SF4B-A48CA-J05

499 FIBER SENSORS Compact Light Curtain Type 4 SF4B-C SERIES Related Information LASER SENSORS ■■General terms and conditions.............. F-7 ■■SF-C10.......................................... P.703~ ■■General precautions.................... P.1458~ ■■Sensor selection guide.................. P.497~ ■■Glossary of terms........................ P.1455~ ■■Korea’s S-mark.............................. P.1506 PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Conforming to Machine & EMC Directive AREA SENSORS Conforming to OSHA / ANSI Certified by NRTL LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS Certified Certified PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS diagnosis Category 4 PLe SIL3 panasonic.net/id/pidsx/global Compact, light weight design, and advanced functionality in one package Test input PNP output type available Compact profile design, maximize the machinery opening area The SF4B-C series is designed to fit onto an aluminum frame, maximizing the machinery opening area. It can even allow zero dead zone. Side mounting MACHINE VISION SYSTEMS UV CURING SYSTEMS Width Just Selection Guide Self-diagnosis 20 0.787 mm Depth in 27.4 1.079 mm ■ The presence of light curtain does not narrow the opening area. ■ The light curtain is thin, so its bulge from frame can be minimized. * When using standard mounting brackets (optional) in Light Curtains Safety Components Optical Touch Switch Control Units Definition of Sensing Heights SF4B-C SF4C SF2C SF4B SF2B BSF4-AH80 BSF4-AH80 Buried mounting (side) ■ The light curtain fits onto frame perfectly, even in embedded installations. ■ The light curtain protrudes neither into the machinery opening nor outside the frame. ■ The light curtain will not be damaged due to collision with workpiece. * When using standard mounting brackets (optional) Rear mounting ■ The light curtain fits onto a 20 × 20 mm 0.787 × 0.787 in aluminum frame perfectly. ■ The light curtain does not protrude from the frame. * When using standard mounting brackets (optional) Compact Light Curtain Type 4 SF4B-C SERIES Plastic × metal Maximum protection height of 1,943.4 mm 76.512 in The SF4B-C series features a proprietary double structure of a “plastic body” with a “metal inner frame” which lightens the weight while maintaining the durability. Despite its compact, plastic body, the SF4B-C series features a metal inner frame that increases toughness and also keeps its enclosure not to curve. Protective heights range from 263.4 mm to 1,943.4 mm 10.370 in to 76.512 in. 500 FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS Metal inner frame Plastic seamless enclosure PARTICULAR USE SENSORS * This is an only image for seamless enclosure partially cut. Max. 1,943.4 mm 76.512 in SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES Min. 263.4 mm 10.370 in LASER MARKERS PLC HUMAN MACHINE INTERFACES 45% lighter* for easy installation in high places and when mounting long models ENERGY CONSUMPTION VISUALIZATION COMPONENTS Thanks to its plastic body, the SF4B-C series is 45% lighter* than previous models with aluminum enclosures. This helps to reduce the overall weight of the equipment during transport and when shipping it overseas. FA COMPONENTS MACHINE VISION SYSTEMS * Comparing SF4B-H80 with SF4B-H80CA-J05 UV CURING SYSTEMS Selection Guide Light Curtains Large multi-purpose indicator SF4B-□CA-J05 The SF4B-C series incorporates a large multi-purpose indicator (orange) positioned around workers’ eye level. The indicator shows the presence of the light curtain, helping to prevent unintentional beam interruption. The indicator can be used in a variety of applications such as a muting indicator and work indicator. Safety Components Optical Touch Switch Control Units Definition of Sensing Heights SF4B-C SF4C Exceptional visibility with wide angle The large multi-purpose indicator shines brightly through the plastic body to ensure exceptional visibility. SF2C SF4B SF2B BSF4-AH80 501 FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS Compact Light Curtain Type 4 SF4B-C SERIES Handy-controller SFB-HC (optional) offers easy access to settings for a range of functionality Muting control function for individual beams: Limit the muting area SF4B-□CA-J05 Fixed blanking function: Choose active beam channels The SFB-HC handy-controller (optional) allows to perform muting control for certain beams only. Since beam channels can be specified, so there is no need to install a separate guard to prevent intrusions. For example, according to the height of a sensing object, when muting control from the lowermost beam channel to the 10th beam channel is activated, the light curtain will detect any beam interruption at the 11th or higher beam channel as a human entry and stop the machinery. The SFB-HC handy-controller provides a fixed blanking function that prevents control output (OSSD) from turning off even if certain beam channels are interrupted. This function is convenient for applications where an obstacle always interrupts certain beam channels. Additionally, it is safe since control output (OSSD) is forcibly turned off in the event the obstruction moves outside the detection area. During muting (line operating) Line stopped PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Floating blanking function: Disable unspecified beams Use output and indicators to achieve preventive maintenance when the incident light intensity gets unstable The floating blanking function allows to disable up to three unspecified beam channels. Control output (OSSD) will not turn off as long as the number of interrupted beam channels is less than the set number of beam channels. This function is convenient when an obstruction moves inside the detection area during setup changes or when loading materials within the detection area of light curtain. By setting the auxiliary output switching function to off or on when light reception becomes unstable, the light curtain provides notification in the event of a reduction in the incident light intensity due to beam misalignment or dirt via auxiliary output (non-safety output) in addition to the incident light intensity indicator. Auxiliary output Incident light intensity indicator * The min. sensing object will change when the floating blanking function is used. Incident light intensity (Note 1) LASER MARKERS Selection Guide 130 % 100 % Set to off for unstable incident light (Note 3) Set to on for unstable incident light (Note 3) ON OFF OFF ON Under stable light received condition: Green Incident light intensity: 130 % or greater Under unstable light received condition: Orange Incident light intensity: 100 % to less than 130 % When light is interrupted (Note 2): Off Notes: 1) An incident light intensity value of 100 % refers to the threshold value at which control outputs (OSSD1, OSSD2) change from off to on. 2) Interruption of the light refers to the presence of an object interrupts beam in the detection area. 3) This setting is not available when using muting control for individual beams, fixed blanking, or floating blanking. Light Curtains Safety Components Optical Touch Switch Control Units Definition of Sensing Heights SF4B-C SF4C SF2C SF4B SF2B BSF4-AH80 BSF4-AH80 Extensive array of other functions PNP / NPN polarity support Extraneous light check & avoid (ELCA) function Since a single model number can be switched between PNP and NPN input, fewer model numbers need to be registered. The ELCA function reduces interference without an interference prevention line. External device monitor function Beam-axis alignment indicator External devices (such as safety relays, etc.) can be directly connected to the handy-controller without any dedicated unit, simplifying installation, reducing costs, and helping to avoid various problems. Beam-axis alignment indicators are indicated in 4 blocks, allowing to see at a glance where light is being received. Compact Light Curtain Type 4 SF4B-C SERIES PRODUCT CONFIGURATION 502 FIBER SENSORS Pigtailed type (with muting function) (with 0.5 m 1.640 ft connector attached cable) LASER SENSORS Cable type (with 5 m 16.404 ft cable) PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS 1 2 LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS 3 5 INDUCTIVE PROXIMITY SENSORS 3 4 Cable 5 m 16.404 ft (discrete wire) Connector attached cable 0.5 m 1.640 ft SENSOR OPTIONS ORDER GUIDE 1 SIMPLE WIRE-SAVING UNITS 2 Light curtains Hand protection type Arm / Foot protection type Min. sensing object ø45 mm ø1.772 in (40 mm 1.575 in beam pitch) Min. sensing object ø25 mm ø0.984 in (20 mm 0.787 in beam pitch) Type Appearance Beam channel No. Operating range (Note 1) 22.2 mm 0.874 in Protective height Beam pitch 20 mm 0.787 in 0.3 to 7 m 0.984 to 22.966 ft 22.2 mm 0.874 in 42.2 mm 1.661 in Beam pitch Protective 40 mm height 1.575 in Beam channel No. 0.3 to 7 m 0.984 to 22.966 ft 42.2 mm 1.661 in Model No. (Note 2) WIRE-SAVING SYSTEMS 1 Pigtailed type 2 Cable type Number of beam channels SF4B-H12CA-J05 SF4B-H12C 12 263.4 mm 10.370 in SF4B-H16CA-J05 SF4B-H16C 16 343.4 mm 13.520 in STATIC ELECTRICITY PREVENTION DEVICES SF4B-H20CA-J05 SF4B-H20C 20 423.4 mm 16.669 in LASER MARKERS SF4B-H24CA-J05 SF4B-H24C 24 503.4 mm 19.819 in SF4B-H28CA-J05 SF4B-H28C 28 583.4 mm 22.969 in SF4B-H32CA-J05 SF4B-H32C 32 663.4 mm 26.118 in SF4B-H36CA-J05 SF4B-H36C 36 743.4 mm 29.268 in SF4B-H40CA-J05 SF4B-H40C 40 823.4 mm 32.417 in SF4B-H48CA-J05 SF4B-H48C 48 983.4 mm 38.717 in SF4B-H56CA-J05 SF4B-H56C 56 1,143.4 mm 45.016 in SF4B-H64CA-J05 SF4B-H64C 64 1,303.4 mm 51.315 in SF4B-H72CA-J05 SF4B-H72C 72 1,463.4 mm 57.614 in SF4B-H80CA-J05 SF4B-H80C 80 1,623.4 mm 63.913 in SF4B-H88CA-J05 SF4B-H88C 88 1,783.4 mm 70.212 in SF4B-H96CA-J05 SF4B-H96C 96 1,943.4 mm 76.512 in SF4B-A8CA-J05 SF4B-A8C 8 343.4 mm 13.520 in SF4B-A12CA-J05 SF4B-A12C 12 503.4 mm 19.819 in SF4B-A16CA-J05 SF4B-A16C 16 663.4 mm 26.118 in SF4B-A20CA-J05 SF4B-A20C 20 823.4 mm 32.417 in SF4B-A24CA-J05 SF4B-A24C 24 983.4 mm 38.717 in SF4B-A28CA-J05 SF4B-A28C 28 1,143.4 mm 45.016 in SF4B-A32CA-J05 SF4B-A32C 32 1,303.4 mm 51.315 in SF4B-A36CA-J05 SF4B-A36C 36 1,463.4 mm 57.614 in SF4B-A40CA-J05 SF4B-A40C 40 1,623.4 mm 63.913 in SF4B-A44CA-J05 SF4B-A44C 44 1,783.4 mm 70.212 in SF4B-A48CA-J05 SF4B-A48C 48 1,943.4 mm 76.512 in (with muting function) Notes: 1) The operating range is the distance possible to set between the emitter and the receiver. Receiver cannot be placed in this range Actual operating range of the light curtain 0.3 m 0.984 ft Setting range of the receiver Emitter Receiver PARTICULAR USE SENSORS 7 m 22.966 ft Protective height MEASUREMENT SENSORS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Light Curtains Safety Components Optical Touch Switch Control Units Definition of Sensing Heights SF4B-C SF4C SF2C SF4B SF2B BSF4-AH80 Receiver 2) The model No. with “E” shown on the label affixed to the product is the emitter, “D” shown on the label is the receiver. 503 FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS Compact Light Curtain Type 4 SF4B-C SERIES ORDER GUIDE 3 Mounting brackets Mounting bracket is not supplied with the light curtain. Be sure to order it separately. Designation Appearance Model No. Description MS-SF4BC-1 Allows the light curtain to be mounted on the rear or side of the target equipment. Designed for use with one M5 hexagon-socket head bolt. (4 pcs. per set for the emitter and receiver) MS-SF4BC-2 Allows the light curtain to be mounted on the rear of the target equipment. Allows beam adjustment. Designed for use with one M5 hexagon-socket head bolt. For space-saving mounting, use one M5 hexagon head bolt. (4 pcs. per set for the emitter and receiver) MS-SF4BC-3 Allows the light curtain to be mounted on the side of the target equipment. Allows beam adjustment. Designed for use with one M5 hexagon-socket head bolt. For space-saving mounting, use one M5 hexagon head bolt. (4 pcs. per set for the emitter and receiver) MS-SF4BC-4 Supports the middle of the light curtain when installing it with utility mounting brackets. Allows the light curtain to be mounted on the rear or side of the target equipment. Allows beam adjustment. Designed for use with one M5 hexagon head bolt. (2 pcs. each per set for rear mounting and side mounting) Intermediate supporting bracket for standard mounting bracket (Note) MS-SF4BC-5 Supports the middle of the light curtain when installing it with standard mounting brackets. Allows the light curtain to be mounted on the rear or side of the target equipment. Designed for use with two M3 countersunk screws. (2 pcs. each per set for rear mounting and side mounting) Side mounting bracket MS-SF4BC-6 Allows beam axis alignment and the light curtain to be mounted on the device in confined spaces. Designed for use with one M5 hexagon-socket head bolt. (4 pcs. per set for the emitter and receiver) MS-SF4BC-7 Supports the middle of the light curtain when installing it with side mounting brackets. Allows beam axis alignment and the light curtain to be mounted on the device in confined spaces. Designed for use with one M5 hexagon-socket head bolt. (2 pces. per set) Standard mounting bracket Rear utility mounting bracket INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS Side utility mounting bracket SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS Intermediate supporting bracket for utility mounting bracket (Note 1) MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Light Curtains Safety Components Optical Touch Switch Control Units Definition of Sensing Heights SF4B-C Intermediate supporting bracket for use with side mounting bracket (Note) Note: The numbers of sets required by SF4B-H□C(A-J05)(40 or more beam axes) and SF4B-A□C(A-J05) (20 or more beam axes) are as follows: SF4B-H40C(A-J05), SF4B-H48C(A-J05), SF4B-H56C(A-J05), SF4B-A20C(A-J05), SF4B-A24C(A-J05), SF4B-A28C(A-J05): 1 set SF4B-H64C(A-J05), SF4B-H72C(A-J05), SF4B-H80C(A-J05), SF4B-H88C(A-J05), SF4B-H96C(A-J05), SF4B-A32C(A-J05), SF4B-A36C(A-J05), SF4B-A40C(A-J05), SF4B-A44C(A-J05), SF4B-A48C(A-J05): 2 sets Standard mounting bracket and intermediate supporting bracket for standard mounting bracket In case of side mounting In case of side mounting Rear utility mounting bracket and intermediate supporting bracket for utility mounting bracket Space-saving mounting (Note) Standard mounting Standard mounting bracket MS-SF4BC-1 Rear utility mounting bracket MS-SF4BC-2 Intermediate supporting bracket for standard mounting bracket Intermediate supporting bracket for utility mounting bracket MS-SF4BC-4 MS-SF4BC-5 SF4C Side utility mounting bracket and intermediate supporting bracket for utility mounting bracket Space-saving mounting (Note) Standard mounting Side utility mounting bracket MS-SF4BC-3 Intermediate supporting bracket for utility mounting bracket MS-SF4BC-4 Side mounting bracket and intermediate supporting bracket for use with side mounting bracket Space-saving mounting Standard mounting Side mounting bracket MS-SF4BC-6 Intermediate supporting bracket for use with side mounting bracket MS-SF4BC-7 SF2C SF4B SF2B BSF4-AH80 Standard mounting bracket MS-SF4BC-1 Rear utility mounting bracket MS-SF4BC-2 Side utility mounting bracket MS-SF4BC-3 Side mounting bracket MS-SF4BC-6 • MS-SF4BC-1 • MS-SF4BC-2 • MS-SF4BC-3 • MS-SF4BC-6 • MS-SF4BC-5 • MS-SF4BC-4 • MS-SF4BC-4 • MS-SF4BC-7 Four brackets (two each R and L type) per set Eight M3 (length: 5 mm 0.197 in) hexagon-socket head bolts and four M5 flat washers are attached. Two pcs. for rear mounting, two pcs. for side mounting Four brackets (two each R and L type) per set Eight M3 (length: 6 mm 0.236 in) hexagon-socket head bolts and four M5 flat washers are attached. Two brackets per set M5 flat washers, two pcs. assembled M3 (length: 6 mm 0.236 in) hexagon-socket head bolts for rear mounting, two pcs. attachments for side mounting Note: For space-saving mounting, use an M5 hexagon head bolt. Four brackets (two each R and L type) per set Eight M3 (length: 6 mm 0.236 in) hexagon-socket head bolts and four M5 flat washers are attached. Two brackets per set M5 flat washers, two pcs. assembled M3 (length: 6 mm 0.236 in) hexagon-socket head bolts for rear mounting, two pcs. attachments for side mounting Four brackets (two each R and L type) per set Eight M3 (length: 6 mm 0.236 in) hexagon-socket head bolts and four M5 flat washers are attached. Two brackets per set Two pcs. M5 flat washers, two pcs. assembled M3 (length: 6 mm 0.236 in) hexagon-socket head bolts for side mounting Compact Light Curtain Type 4 4 504 ORDER GUIDE FIBER SENSORS 5 Mating cables LASER SENSORS PHOTOELECTRIC SENSORS Description SFB-CC10-MU Length: 3 m 9.843 ft Cable with connector on one end for pigtailed type (with Net weight: 430 g approx. (2 cables) muting function) Two cables per set for emitter and receiver Length: 7 m 22.966 ft Cable color: Gray for emitter, Net weight: 1,000 g approx. (2 cables) Gray with black line for receiver Connector color: Gray for emitter, Black for receiver Length: 10 m 32.808 ft Net weight: 1,300 g approx. (2 cables) Min. bending radius: R6 mm R0.236 in SFB-CCJ3E-MU Length: 3 m 9.843 ft Net weight: 190 g approx. (1 cable) SFB-CC7-MU For emitter 5 Model No. SFB-CC3-MU SFB-CCJ10E-MU Length: 10 m 32.808 ft Net weight: 660 g approx. (1 cable) For receiver With connectors on both ends 4 Appearance With connector on one end Type Mating cables SF4B-C SERIES SFB-CCJ3D-MU Length: 3 m 9.843 ft Net weight: 210 g approx. (1 cable) Cable with connectors on both ends for pigtailed type (with muting function) Cable color: Gray for emitter, Gray with black line for receiver Connector color: Gray for emitter, Black for receiver Min. bending radius: R6 mm R0.236 in SFB-CCJ10D-MU Length: 10 m 32.808 ft Net weight: 680 g approx. (1 cable) Model No. Test rod ø25 SF4B-TR25 LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS Description STATIC ELECTRICITY PREVENTION DEVICES Min. sensing object for regular checking (ø25 mm ø0.984 in), for hand protection type (min. sensing object ø25 mm ø0.984 in) LASER MARKERS OPTIONS PLC Control units Designation AREA SENSORS SIMPLE WIRE-SAVING UNITS Spare parts (Accessories for light curtain) Designation MICRO PHOTOELECTRIC SENSORS HUMAN MACHINE INTERFACES Appearance Slim type control unit Model No. Description ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS SF-C13 Use a discrete wire cable to connect to the light curtain. Muting function can be used. Compatible with up to Control Category 4. When connecting pigtailed type (with muting function) SF4B-□CA-J05, be sure to order a mating cable separately. • Mating cable: SFB-CC□-MU • Extension cable: SFB-CCJ□-MU MACHINE VISION SYSTEMS UV CURING SYSTEMS Handy-controller Designation Appearance Model No. Pigtailed type (with muting function) Selection Guide Light Curtains Handycontroller Fix ed Floa bla ting nki Aux blan ng Lig iliary king ht con emoutput trol iss ion Co de Mo Pr nitor ote Co ct py FU NC TIO N CA Safety Components SFB-HC 8core NC EL EN TE R Optical Touch Switch 8core Control Units Definition of Sensing Heights FUNCTION 12-core → 8-core * 2 adapter cables included 8-core → 12-core CANCEL ENTER Adapter cable (Accessory) Adapter cable (Accessory) Extension cable Handy-controller Cable set for cable type connection SFC-WNC1 SF4B-C SF4C Cable type SF2C SF4B 12-core → 8-core +V 0V Cable set Synchronization Synchronization + Control circuit SF2B Adapter cable (Accessory) Not used 8-core 8-core FUNCTION CANCEL Terminal block ENTER Handy-controller BSF4-AH80 505 FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Compact Light Curtain Type 4 SF4B-C SERIES OPTIONS Metal protection case Designation Applicable beam channels Hand protection Arm / Foot type protection type AREA SENSORS 12 16 20 24 28 32 36 40 48 56 64 72 80 88 96 LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS Metal protection case (2 pcs. per set) (Note) Appearance Model No. MS-SF4BCH-12 MS-SF4BCH-16 MS-SF4BCH-20 MS-SF4BCH-24 MS-SF4BCH-28 MS-SF4BCH-32 MS-SF4BCH-36 MS-SF4BCH-40 MS-SF4BCH-48 MS-SF4BCH-56 MS-SF4BCH-64 MS-SF4BCH-72 MS-SF4BCH-80 MS-SF4BCH-88 MS-SF4BCH-96 8 12 16 20 24 28 32 36 40 44 48 Note: In the case of using a metal protection case MS-SF4BCH-□(optional), make sure to assemble it with a standard mounting bracket MS-SF4BC-1 (optional). STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS Others Designation Test rod ø45 Model No. SF4B-TR45 Min. sensing object for regular checking (ø45 mm ø1.772 in), for arm / foot protection type (min. sensing object ø45 mm ø1.772 in) With the auxiliary output of the light curtain, the operation is easily observable from various directions. Specifications FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Large display unit for light curtain Description Large display unit for light curtain SF-IND-2 • Supply voltage: 24 V DC ±15 % • Current consumption: 12 mA or less • Indicators: Orange LED (8 pcs. used) [Light up when external contact is ON] • Ambient temperature: –10 to +55 °C +14 to +131 °F (No dew condensation or icing allowed) • Material: POM (Enclosure) Polycarbonate (Cover) Cold rolled carbon steel (SPCC) (Bracket) • Cable: 0.3 mm2 2-core cabtyre cable, 3 m 9.843 ft long • Weight: 70 g approx. (including bracket) • SF-IND-2 M5 hexagonsocket head bolt length: 10 mm 0.394 in or more Purchase separately. * Cannot be attached together with a mounting bracket to the light curtain using a single bolt. Selection Guide Light Curtains Safety Components Optical Touch Switch Control Units Definition of Sensing Heights SF4B-C SF4C Recommended safety relay Safety relay Panasonic Corporation SF series Safety relay SFS3-L-DC24V (AG1S132) SFS4-L-DC24V (AG1S142) DIN terminal block SFS4-SFD (AG1S847)[4-poles type] SFS6-SFD (AG1S867)[6-poles type] SF2C SF4B SF2B BSF4-AH80 Note: Contact Panasonic Corporation for details on the recommended products. Item Type Model No. Part No. Contact arrangement Rated nominal switching capacity Min. switching capacity Coil rating Rated power consumption Operation time Release time Ambient temperature Applicable standards With LED indicator SFS3-L-DC24V SFS4-L-DC24V AG1S132 AG1S142 3a1b 4a2b 6 A / 250 V AC, 6 A / 30 V DC 1 mA / 5 V DC 15 mA / 24 V DC 20.8 mA / 24 V DC 360 mW 500 mW 20 ms or less 20 ms or less –40 to +85 °C –40 to +185 °F (Humidity: 5 to 85 % RH) • • UL, C-UL, TUV, Korea's S-mark Compact Light Curtain Type 4 SF4B-C SERIES SPECIFICATIONS FIBER SENSORS Model No. Light curtain individual specifications SF4B-H□C(A-J05) Item Type SF4B-H12CA-J05 Pigtailed type SF4B-H12C Cable type Number of beam channels Protective height Item Pigtailed type Model No. Current consumption Cable type When large multi-purpose indicator turns OFF When large multi-purpose indicator lights up PFHd* MTTFd* Net weight Pigtailed type (Total of emitter and receiver) Cable type 12 263.4 mm 10.37 in Protective height LASER SENSORS Min. sensing object ø25 mm ø0.984 in (20  mm 0.787 in beam pitch) SF4B-H16CA-J05 SF4B-H20CA-J05 SF4B-H24CA-J05 SF4B-H28CA-J05 SF4B-H32CA-J05 SF4B-H16C SF4B-H20C SF4B-H24C SF4B-H28C SF4B-H32C 16 343.4 mm 13.52 in 24 503.4 mm 19.819 in 28 583.4 mm 22.969 in Emitter: 70 mA or less Receiver: 85 mA or less Emitter: 80 mA or less Receiver: 95 mA or less 2.4 × 10−9 2.6 × 10−9 2.8 × 10−9 100 years or more Approx.520 g Approx. 590 g Approx. 680 g Approx. 860 g Approx. 930 g Approx. 1,000 g Emitter: 75 mA or less, Receiver: 85 mA or less 1.9 × 10 −9 Approx. 360 g Approx. 700 g 40 823.4 mm 32.417 in 2.1 × 10 −9 Approx. 430 g Approx. 770 g 32 663.4 mm 26.118 in 48 983.4 mm 38.717 in Pigtailed type 56 1,143.4 mm 45.016 in 64 1,303.4 mm 51.315 in Emitter: 85 mA or less Receiver: 120 mA or less 72 1,463.4 mm 57.614 in PHOTOELECTRIC SENSORS SF4B-H36CA-J05 SF4B-H36C 36 743.4 mm 29.268 in Emitter: 75 mA or less Receiver: 95 mA or less Emitter: 85 mA or less Receiver: 105 mA or less 3.0 × 10−9 3.3 × 10−9 Approx. 750 g Approx. 1,100 g Min. sensing object ø25 mm ø0.984 in (20 mm 0.787 in beam pitch) SF4B-H48CA-J05 SF4B-H56CA-J05 SF4B-H64CA-J05 SF4B-H72CA-J05 SF4B-H80CA-J05 SF4B-H48C SF4B-H56C SF4B-H64C SF4B-H72C SF4B-H80C Cable type Emitter: 80 mA or less When large multi-purpose Receiver: 100 mA or less indicator turns OFF When large multi-purpose Emitter: 90 mA or less indicator lights up Receiver: 110 mA or less PFHd* 3.5 × 10−9 3.9 × 10−9 MTTFd* Approx. 910 g Approx. 1,100 g Net weight Pigtailed type (Total of emitter and receiver) Cable type Approx. 1,300 g Approx. 1,400 g Current consumption 20 423.4 mm 16.669 in Emitter: 65 mA or less, Receiver: 75 mA or less Type SF4B-H40CA-J05 Pigtailed type SF4B-H40C Cable type Number of beam channels 80 1,623.4 mm 63.913 in Emitter: 95 mA or less Receiver: 130 mA or less Approx. 840 g Approx. 1,200 g SF4B-H88CA-J05 SF4B-H88C 88 1,783.4 mm 70.212 in Emitter: 100 mA or less Receiver: 140 mA or less Emitter: 95 mA or less Emitter: 105 mA or less Emitter: 110 mA or less Receiver: 130 mA or less Receiver: 140 mA or less Receiver: 155 mA or less 4.4 × 10−9 4.8 × 10−9 5.3 × 10−9 5.7 × 10−9 6.2 × 10−9 100 years or more Approx. 1,300 g Approx. 1,400 g Approx. 1,600 g Approx. 1,700 g Approx. 1,800 g Approx. 1,600 g Approx. 1,700 g Approx. 2,000 g Approx. 2,000 g Approx. 2,100 g * PFHd: Probability of dangerous failure per hour, MTTFd: Mean time to dangerous failure. Model No. Item Pigtailed type Cable type Number of beam channels Protective height Item Pigtailed type Model No. Current consumption Cable type When large multi-purpose indicator turns OFF When large multi-purpose indicator lights up PFHd* MTTFd* Net weight Pigtailed type (Total of emitter and receiver) Cable type Min. sensing object ø25 mm ø0.984 in (20 mm 0.787 in beam pitch) SF4B-H96CA-J05 SF4B-H96C 96 1,943.4 mm 76.512 in Emitter: 105 mA or less Receiver: 145 mA or less Emitter: 115 mA or less Receiver: 155 mA or less 6.6 × 10−9 100 years or more Approx. 1,900 g Approx. 2,200 g Type SF4B-A24CA-J05 Pigtailed type SF4B-A24C Cable type Number of beam channels Protective height 24 983.4 mm 38.717 in Pigtailed type Emitter: 60 mA or less Receiver: 70 mA or less 16 663.4 mm 26.118 in 28 1,143.4 mm 45.016 in 36 1,463.4 mm 57.614 in Emitter: 65 mA or less Receiver: 75 mA or less INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS Selection Guide 40 1,623.4 mm 63.913 in 44 1,783.4 mm 70.212 in Light Curtains Safety Components Optical Touch Switch Control Units Definition of Sensing Heights SF4B-A48CA-J05 SF4B-A48C 48 1,943.4 mm 76.512 in Emitter: 75 mA or less Receiver: 95 mA or less Emitter: 80 mA or less Receiver: 100 mA or less Emitter: 85 mA or less Receiver: 105 mA or less 3.2 × 10−9 3.4 × 10−9 3.7 × 10−9 100 years or more Approx. 1,400 g Approx. 1,600 g Approx. 1,700 g Approx. 1,700 g Approx. 2,000 g Approx. 2,000 g Emitter: 90 mA or less Receiver: 110 mA or less 3.9 × 10−9 4.2 × 10−9 * PFHd: Probability of dangerous failure per hour. MTTFd: Mean time to dangerous failure. PRESSURE / FLOW SENSORS UV CURING SYSTEMS Emitter: 70 mA or less Emitter: 75 mA or less Receiver: 80 mA or less Receiver: 85 mA or less 1.7 × 10−9 1.9 × 10−9 2.2 × 10−9 2.4 × 10−9 100 years or more Approx. 430 g Approx. 590 g Approx. 750 g Approx. 910 g Approx. 770 g Approx. 930 g Approx. 1,100 g Approx. 1,300 g 32 1,303.4 mm 51.315 in LIGHT CURTAINS / SAFETY COMPONENTS 20 823.4 mm 32.417 in Min. sensing object ø45 mm ø1.772 in (40 mm 1.575 in beam pitch) SF4B-A28CA-J05 SF4B-A32CA-J05 SF4B-A36CA-J05 SF4B-A40CA-J05 SF4B-A44CA-J05 SF4B-A28C SF4B-A32C SF4B-A36C SF4B-A40C SF4B-A44C Cable type Emitter: 70 mA or less When large multi-purpose Receiver: 85 mA or less indicator turns OFF When large multi-purpose Emitter: 80 mA or less indicator lights up Receiver: 95 mA or less PFHd* 2.7 × 10−9 2.9 × 10−9 MTTFd* Approx. 1,100 g Approx. 1,300 g Net weight Pigtailed type (Total of emitter and receiver) Cable type Approx. 1,400 g Approx. 1,600 g Current consumption 12 503.4 mm 19.819 in AREA SENSORS MACHINE VISION SYSTEMS Min. sensing object ø45 mm ø1.772 in (40 mm 1.575 in beam pitch) SF4B-A8CA-J05 SF4B-A12CA-J05 SF4B-A16CA-J05 SF4B-A20CA-J05 SF4B-A8C SF4B-A12C SF4B-A16C SF4B-A20C 8 343.4 mm 13.52 in MICRO PHOTOELECTRIC SENSORS FA COMPONENTS SF4B-A□C(A-J05) Type 506 Approx. 1,800 g Approx. 2,100 g Approx. 1,900 g Approx. 2,200 g SF4B-C SF4C SF2C SF4B SF2B BSF4-AH80 507 Compact Light Curtain Type 4 SPECIFICATIONS FIBER SENSORS LASER SENSORS Light curtain common specifications Pigtailed type (with muting function) Cable type Min. sensing object Min. sensing object Min. sensing object Min. sensing object ø25 mm ø0.984 in ø45 mm ø1.772 in ø25 mm ø0.984 in ø45 mm ø1.772 in (20  mm 0.787 in beam pitch) (40 mm 1.575 in beam pitch) (20  mm 0.787 in beam pitch) (40 mm 1.575 in beam pitch) SF4B-H□CA-J05 SF4B-A□CA-J05 SF4B-H□C SF4B-A□C Model No. PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS Type Item Applicable standards MICRO PHOTOELECTRIC SENSORS International standard MEASUREMENT SENSORS JIS B 9704-1/2 (Type 4), JIS B 9705-1 (Category 4), JIS C 0508 (SIL3) Europe (EU) (Note 2) North America (Note 3) South Korea (S-Mark) Operating range (Note 4) Beam pitch Min. sensing object (Note 5) Effective aperture angle Supply voltage Control outputs (OSSD 1, OSSD 2) STATIC ELECTRICITY PREVENTION DEVICES PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Light Curtains Safety Components Optical Touch Switch Control Units Definition of Sensing Heights SF4B-C SF4C SF2C SF4B SF2B BSF4-AH80 Operation mode Protection circuit Response time Auxiliary output (Non-safety output) EN 61496-1 (Type 4), EN ISO 13849-1 (Category 4, PLe), EN 61508-1 to 7 (SIL3), EN 55011, EN 50178, EN 61000-6-2 ANSI/UL 61496-1/2 (Type 4), ANSI/UL 508, CAN/CSA 61496-1/2 (Type 4), CAN/CSA C22.2 No.14, OSHA 1910.212, OSHA 1910.217(C), ANSI B11.1 to B11.19, ANSI/RIA 15.06 S1-G-35-2005, S2-W-11-2003 0.3 to 7 m 0.984 to 22.966 ft 20 mm 0.787 in 40 mm 1.575 in 20 mm 0.787 in 40 mm 1.575 in ø25 mm ø0.984 in opaque object ø45 mm ø1.772 in opaque object ø25 mm ø0.984 in opaque object ø45 mm ø1.772 in opaque object ±2.5° or less [for an operating range exceeding 3 m 9.843 ft (conforming to IEC 61496-2 / UL 61496-2)] 24 V DC ±10 % Ripple P-P 10 % or less PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 200 mA • Maximum sink current: 200 mA • Applied voltage: Same as supply voltage (between the control output • Applied voltage: Same as supply voltage (between the control output and +V) and 0 V) • Residual voltage: 2.5 V or less • Residual voltage: 2.5 V or less (source current 200 mA, when using 20 m 65.617 ft length cable) (sink current 200 mA, when using 20 m 65.617 ft length cable) • Leakage current: 0.1 mA or less (Including power supply OFF • Leakage current: 0.1 mA or less (Including power supply OFF condition) condition) • Maximum load capacity: 0.22 μF (No load to maximum output current) • Maximum load capacity: 0.22 μF (No load to maximum output current) • Load wiring resistance: 3 Ω or less • Load wiring resistance: 3 Ω or less ON when all beam channels are received, OFF when one or more beam channels are interrupted (OFF also in case of any malfunction in the light curtain or the synchronization signal) (Note 6, 7) Incorporated OFF response: 14 ms or less, ON response: 80 to 90 ms PNP open-collector transistor / NPN open-collector transistor (switching method) • Maximum source current: 60 mA • Maximum sink current: 60 mA • Applied voltage: Same as supply voltage (between the auxiliary • Applied voltage: Same as supply voltage (between the auxiliary output and +V) output and 0 V) • Residual voltage: 2.5 V or less • Residual voltage: 2.5 V or less (source current 60 mA, when using 20 m 65.617 ft length cable) (sink current 60 mA, when using 20 m 65.617 ft length cable) OFF when control outputs are ON, ON when control outputs are OFF [Factory setting, operating mode can be changed using the SFB-HC (optional) handy-controller.] Incorporated NPN open-collector transistor • Maximum sink current: 100 mA • Applied voltage: Same as supply voltage (between the Muting auxiliary output muting auxiliary output and 0 V) • Residual voltage: 2.5 V or less (sink current 100 mA, when using 20 m 65.617 ft length cable) When muting auxiliary output: ON Operation mode Protection circuit Incorporated ELCA function Incorporated (reducing mutual interference automatically) Emission halt function Incorporated Interlock function Incorporated [Manual reset / Auto reset (Note 8)] External device monitoring function Incorporated Override function Incorporated Muting function Incorporated Large multi-purpose indicator function Incorporated Muting setting changing, override setting changing, fixed Fixed blanking, floating blanking, light emitting amount control, blanking, floating blanking, light emitting amount control, Optional functions (Note 9) auxiliary output switching, protecting, interlock setting auxiliary output switching, protecting, interlock setting changing, external relay monitor setting changing changing, external relay monitor setting changing Pollution degree 3 Operating altitude 2,000 m 6,561.68 ft or less (Note 10) Degree of protection IP65 (IEC) Ambient temperature –10 to +55 °C +14 to +131 °F (No dew condensation or icing allowed), Storage: –25 to +60 °C –3 to +140 °F Ambient humidity 30 to 85 % RH, Storage: 30 to 85 % RH Ambient illuminance Incandescent light: 3,500 ℓx or less at the light-receiving face Dielectric strength voltage / 1,000 V AC for one min. between all supply terminals connected together and enclosure / 20 MΩ or more, with 500 V DC Insulation resistance megger between all supply terminals connected together and enclosure 10 to 55 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each / 300 m/s2 acceleration Vibration resistance / (30 G approx.) in X, Y and Z directions for three times each Shock resistance Operation mode Protection circuit Environmental resistance LASER MARKERS IEC 61496-1/2 (Type 4), ISO 13849-1 (Category 4, PLe), IEC 61508-1 to 7 (SIL3) Japan SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS SF4B-C SERIES Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F. 2) Regarding EU Machinery Directive, a Notified Body, TÜV SÜD, has certified with the type examination certificate. 3) The product has been safety-certified in accordance with UL, ANSI, CSA, and other standards by TÜV SÜD, a nationally recognized safety laboratory (NRTL) that has been approved by the Occupational Safety and Health Administration (OSHA) as defined by 29 CFR 1910.7 4) The operating range is the possible setting distance between the emitter and the receiver. 5) In case the blanking function is valid, the operation mode is changed. 6) During muting, control output will not turn off even if the beams are interrupted. 7) When the blanking function is enabled, the operating mode will change. 8) The manual reset and automatic reset are possible to be switched depending on the wiring status. 9) In case of using optional function, the handy-controller SFB-HC (optional) is required. 10) Do not use or store the device in an environment where the air pressure is higher than the atmospheric pressure at an altitude of 0 meters. Compact Light Curtain Type 4 SF4B-C SERIES SPECIFICATIONS FIBER SENSORS Light curtain common specifications Item Emitting element Material LASER SENSORS Pigtailed type (with muting function) Cable type Min. sensing object Min. sensing object Min. sensing object Min. sensing object Type ø25 mm ø0.984 in ø45 mm ø1.772 in ø25 mm ø0.984 in ø45 mm ø1.772 in (20 mm 0.787 in beam pitch) (40 mm 1.575 in beam pitch) (20  mm 0.787 in beam pitch) (40 mm 1.575 in beam pitch) Model No. SF4B-H□CA-J05 SF4B-A□CA-J05 SF4B-H□C SF4B-A□C Infrared LED (Peak emission wavelength: 850 nm 0.033 mil) Enclosure: Polycarbonate 0.15 mm2 (power line: 0.2 mm2) 12-core heat-resistant PVC 0.15 mm2 (power line: 0.2 mm2) 8-core heat-resistant PVC cable with connector, 0.5 m 1.640 ft long cable, 5 m 16.404 ft long Extension up to total 50 m 164.042 ft is possible for both Extension up to total 50 m 164.042 ft is possible for 0.2 mm2 emitter and receiver optional mating cables or more, cable (Note) Cable Cable extension SF4B-TR25 (Test rod): 1 pc. Accessories SF4B-TR25 (Test rod): 1 pc. Note: When the synchronization + wire (orange) and synchronization - wire (orange / black) is extended with a cable other than exclusive cable, use a 0.2 mm2 or more shielded twisted pair cable. PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS Control unit Connectable light curtains Applicable standards Control category Supply voltage Current consumption Fuse (rating) Enabling path Utilization category Rated operation voltage (Ue) / Rated operation current (le) Contact resistance Contact protection fuse rating Pick-up delay (Auto reset / Manual reset) Response time Auxiliary output Rated operation voltage / current Contact protection fuse rating Semiconductor auxiliary output (AUX) Output operation Excess voltage category Polarity selection function Pollution degree Protection Ambient temperature Ambient humidity Vibration resistance Enclosure material Weight SIMPLE WIRE-SAVING UNITS SF-C13 Light curtains manufactured by Panasonic Industrial Devices SUNX EN 61496-1 (Type 4), EN 55011, EN ISO 13849-1 (Category 4, PLe), IEC 61496-1 (Type 4), ISO 13849-1 (Category 4, PLe), JIS B 9704-1 (Type 4), JIS B 9705-1 (Category 4), ANSI/UL 61496-1 (Type 4), UL 1998 (Class 2) ISO 13849-1 (EN ISO 13849-1, JIS B 9705-1) compliance up to Category 4, PLe standards 24 V DC ±10 % Ripple P-P 10 % or less 100 mA or less (excluding light curtain) Built-in electronic fuse, Triggering current: 0.5 A or more, Reset after power down NO contact × 3 (13-14, 23-24, 33-34) AC-15, DC-13 (IEC 60947-5-1) 30 V DC / 4 A, 230 V AC / 4 A, resistive load (For inductive load, during contact protection) Min. applicable load: 10 mA (at 24 V DC) (Note 2) 100 mΩ or less (initial value) 4 A (slow blow) 80 ms or less / 90 ms or less 10 ms or less Safety relay contact (NC contact) × 1 (41-42) (Related to enabling path) 24 V DC / 2 A, Min. applicable load: 10 mA (at 24 V DC) 2 A (slow blow) PNP open‑collector transistor • Maximum source current: 60 mA ON when the light curtain is interrupted II Incorporated (Cable connection allows selection of plus / minus ground) Minus ground: Correspond to PNP output light curtain Plus ground: Correspond to NPN output light curtain 2 Enclosure: IP40, Terminal: IP20 –10 to +55 °C +14 to +131 °F (No dew condensation or icing allowed), Storage: –25 to +70 °C –13 to +158 °F 30 to 85 % RH, Storage: 30 to 95 % RH Resistance / malfunction 10 to 55 Hz frequency, 0.35 mm 0.014 in amplitude in X, Y, and Z directions for twenty times each ABS Net weight: 200 g approx. Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F. 2) If several SF-C13 units are being used in line together, leave a space of 5 mm 0.197 in or more between each unit. If the units are touching each other, reduce the rated operating current for safety output in accordance with the ambient operating temperature as shown in the graphs at right. 3) Refer to our website for details of specifications. Dilating when SF-C13 units are mounted close together 6 Rated operation current (A) Model No. Item Environmental resistance 508 WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Light Curtains Safety Components Optical Touch Switch Control Units Definition of Sensing Heights SF4B-C 5 SF4C 4 3 SF2C 2 SF4B 1 SF2B 0 32 35 40 45 50 55 95 104 113 122 131 Ambient temperature (°C °F) BSF4-AH80 509 FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS Compact Light Curtain Type 4 SPECIFICATIONS Handy-controller Model No. Item Supply voltage Current consumption Communication method Digital display Function indicator PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS Functions PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Light Curtains Safety Components Optical Touch Switch Control Units Definition of Sensing Heights SF4B-C SF4C SF2C SF4B SF2B BSF4-AH80 SF4B-C SERIES Ambient temperature Ambient humidity Voltage withstandability Insulation resistance Cable Weight Accessory SFB-HC 24 V DC ±10 % Ripple P-P10 % or less (common to light curtain power supply) 65 mA or less RS-485 two-way communications (Specific procedure) 4-digit red LED display × 2 (Selected beam channels, setting contents etc. are displayed.) Green LED × 9 (set function is displayed.) Fixed blanking (Factory setting: Disabled) / Floating blanking (Factory setting: Disabled) / Auxiliary output changing (Factory setting: Negative Logic of OSSD) / Light emitting amount control (Factory setting: Disabled) / Muting setting changing [Factory setting: All beam channels enabled, A = B, Setting of the muting lamp diagnosis function enabled (Ver. 2 or later), Muting sensor output operation setting N.O. / N.O. (Ver. 2.1 or later)] / Interlock setting changing (Factory setting: start / restart) / External device monitoring setting change (Factory setting: Enabled, 300 ms) / Override setting changing 60 sec. (Ver. 2.1 or later) / Setting detail monitoring / / Protecting (Factory setting: Disabled) (Factory password setting: 0000) / Initialization / Copy –10 to +55 °C +14 to +131 °F (No dew condensation or icing allowed), Storage: –25 to +70 °C –13 to +158 °F 30 to 85 % RH, Storage: 30 to 85 % RH 1,000 V AC for one min. between all supply terminals connected together and enclosure 20 MΩ , or more, with 500 V DC megger between all supply terminals connected together and enclosure 8-core shielded cable, 0.5 m 1.640 ft long, with a connector at the end (2 cables) Net weight: 200 g approx. Adapter cable: 2 cables Note: Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F. Compact Light Curtain Type 4 ・ 510 SF4B-C SERIES I/O CIRCUIT AND WIRING DIAGRAMS FIBER SENSORS SF4B-□CA-J05 Pigtailed type (with muting function) PHOTOELECTRIC SENSORS I/O circuit diagrams 0.22 μF Terminal No. of pigtailed type Emitter Lead wire color of mating cable (Brown) +V (Brown) +V (Yellow) Override input (Shield) Output polarity setting wire 470 Ω (Red) Muting auxiliary output *S1 0.22 μF 470 Ω (Pink) Emission halt input / *S1 Reset input 0.22 μF 470 Ω (Pale purple) Interlock setting input LIGHT CURTAINS / SAFETY COMPONENTS Load PRESSURE / FLOW SENSORS Load INDUCTIVE PROXIMITY SENSORS (Yellow-green / Black) Auxiliary output *S1 + – (Yellow-green / Black) Auxiliary output 24 V DC ±10 % (Gray / Black) Large multi-purpose *S1 indicator input (Emitter side) (Gray / Black) Large multi-purpose indicator input (Emitter side) Sensor circuit Sensor circuit AREA SENSORS Load (Red) Muting auxiliary output Load (Gray) NC (Gray) NC – 24 V DC ±10 % SENSOR OPTIONS (Pale purple) Interlock setting input SIMPLE WIRE-SAVING UNITS 0.22 μF 470 Ω (Pink) Emission halt input / *S1 Reset input WIRE-SAVING SYSTEMS 470 Ω (Yellow) Override input MEASUREMENT SENSORS *S1 (Orange) Synchronization+ (Orange) Synchronization+ (Orange / Black) Synchronization- (Orange / Black) SynchronizationInternal circuit STATIC ELECTRICITY PREVENTION DEVICES Users’ circuit LASER MARKERS Receiver 1 kΩ 0.047 μF 1 kΩ 0.22 μF 470 Ω (Orange / Black) Synchronization- (Orange / Black) Synchronization- (Orange) Synchronization+ (Orange) Synchronization+ (Brown) +V (Brown) +V (Sky-blue / White) Muting input A (Shield) Output polarity setting wire (Sky-blue / Black) Muting input B (Yellow-green) External device monitor input HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS K1 (Black) Control output 1 (OSSD 1) *S1 K2 K1 K2 (Gray) NC Sensor circuit PLC *S1 *S1 (Gray / Black) Large multi-purpose indicator input (Receiver side) Sensor circuit 0.047 μF PARTICULAR USE SENSORS 470 Ω (Blue) 0 V Users’ circuit + *S1 (Blue) 0 V Receiver *S1 0.22 μF 0.22 μF (Shield) Output polarity setting wire Internal circuit MICRO PHOTOELECTRIC SENSORS Terminal No. of pigtailed type Emitter Lead wire color of mating cable LASER SENSORS MACHINE VISION SYSTEMS (White) Control output 2 (OSSD 2) (Gray / Black) Large multi-purpose indicator input (Receiver side) FA COMPONENTS *S1 UV CURING SYSTEMS (Black) Control output 1 (OSSD 1) (Gray) NC (White) Control output 2 (OSSD 2) K1 (Shield) Output polarity setting wire K2 470 Ω 0.047 μF 1 kΩ (Sky-blue / White) Muting input A 0.047 μF 1 kΩ (Sky-blue / Black) Muting input B (Blue) 0 V Internal circuit K1, K2: External device (Forced guided relay or magnetic contactor) Users’ circuit *S1 Switch S1 Internal circuit K1 K2 (Yellow-green) External device monitor input 0.22 μF *S1 *S1 (Blue) 0 V K1, K2: External device (Forced guided relay or magnetic contactor) Users’ circuit *S1 Switch S1 • Emission halt input / Reset input For manual reset 0 to +1.5 V (source current 5 mA or less): Emission halt Open: Emission For automatic reset 0 to +1.5 V (source current 5 mA or less): Emission Open: Emission halt • Interlock setting input, Override input, Muting input A / B, External device monitor input Vs to Vs – 2.5 V (sink current 5 mA or less): Valid (Note) Open: Invalid • Interlock setting input, Override input, Muting input A / B, External device monitor input 0 to +1.5 V (source current: 5 mA or less): Valid, Open: Invalid Note: Vs is the applying supply voltage. Light Curtains Safety Components Optical Touch Switch Control Units • Emission halt input / Reset input For manual reset Vs to Vs – 2.5 V (sink current 5 mA or less): Emission halt (Note) Open: Emission For automatic reset Vs to Vs – 2.5 V (sink current 5 mA or less): Emission (Note) Open: Emission halt • Large multi-purpose indicator input 0 to +1.5 V (source current 5 mA or less): Lights up, Open: Turns OFF Selection Guide • Large multi-purpose indicator input 0 to +1.5 V (source current 5 mA or less): Lights up, Open: Turns OFF Definition of Sensing Heights SF4B-C SF4C SF2C SF4B SF2B BSF4-AH80 511 Compact Light Curtain Type 4 ・ I/O CIRCUIT AND WIRING DIAGRAMS FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Muting control components: Interlock function “disabled (automatic reset)”, external device monitoring function “enabled” Lead wire color of mating cable (Gray / Black) Large multi-purpose indicator input (Emitter side) Gray cable (Pale purple) Interlock setting input (Brown) +V (Pink) Emission halt input / Reset input Emitter Receiver (Red) Muting auxiliary output *S1 Load + (Yellow-green / Black) Auxiliary output – Load *S1 (Pink) Emission halt input / Reset input (Orange) Synchronization+ Gray cable (with black line) K1 K2 (Yellow-green) External device monitor input (Brown) +V *S1 *S1 (Sky-blue / White) Muting input A (Black) Control output 1 (OSSD 1) (Shield) Output polarity setting wire Emitter K2 (Blue) 0 V (Yellow-green / Black) Auxiliary output (Gray) NC K1, K2: External device (Forced guided relay or magnetic contactor) *S1 Receiver Switch S1 • Emission halt input / Reset input For automatic reset Vs to Vs – 2.5 V (sink current 5 mA or less): Emission (Note) Open: Emission halt For manual reset Vs to Vs – 2.5 V (sink current 5 mA or less): Emission halt (Note) Open: Emission • Muting input A / B, Override input Vs to Vs – 2.5 V (sink current 5 mA or less): Valid (Note), Open: Invalid (Yellow-green) External device monitor input Note: Vs is the applying supply voltage. Lead wire color of mating cable Emitter Receiver Gray cable Light Curtains In case of setting the external device monitoring function to “disabled” K1 (Gray / Black) Large multi-purpose indicator input (Receiver side) Selection Guide (Pale purple) Interlock setting input (Sky-blue / Black) Muting input B LASER MARKERS UV CURING SYSTEMS +24 V DC (Orange / Black) Synchronization- (White) Control output 2 (OSSD 2) MACHINE VISION SYSTEMS Emitter (Orange / Black) Synchronization- STATIC ELECTRICITY PREVENTION DEVICES FA COMPONENTS • When the interlock function is set to “Enable (manual reset),” the override function cannot be used. (Orange) Synchronization+ MEASUREMENT SENSORS ENERGY CONSUMPTION VISUALIZATION COMPONENTS 24 V DC ±20 % (Blue) 0 V WIRE-SAVING SYSTEMS HUMAN MACHINE INTERFACES In case of setting the interlock function to “enabled (manual reset)” *S1 (Yellow) Override input (Shield) Output polarity setting wire SENSOR OPTIONS PLC The diagram at left shows the configuration when using PNP output, interlock function “disabled (automatic reset)” and external device monitoring function “enabled”. (Gray) NC PARTICULAR USE SENSORS SIMPLE WIRE-SAVING UNITS Pigtailed type (with muting function) Connection examples LIGHT CURTAINS / SAFETY COMPONENTS INDUCTIVE PROXIMITY SENSORS ・ SF4B-□CA-J05 AREA SENSORS PRESSURE / FLOW SENSORS SF4B-C SERIES Safety Components (Gray) NC (Gray / Black) Large multi-purpose indicator input (Emitter side) (Pale purple) Interlock setting input (Brown) +V (Yellow-green / Black) Auxiliary output Load (Shield) Output polarity setting wire (Red) Muting auxiliary output Load (Yellow) Override input (Pink) Emission halt input / Reset input *S1 (Blue) 0 V (Orange) Synchronization+ (Orange / Black) Synchronization(Orange / Black) Synchronization(Orange) Synchronization+ Optical Touch Switch Control Units Definition of Sensing Heights Gray cable (with black line) SF4B-C SF4C SF2C SF4B SF2B (Yellow-green) External device monitor input (Brown) +V (Black) Control output 1 (OSSD 1) K1 (White) Control output 2 (OSSD 2) K2 (Shield) Output polarity setting wire (Sky-blue / White) Muting input A (Sky-blue / Black) Muting input B *S1 The diagram at left shows the configuration when using NPN output, interlock function “disabled (automatic reset)” and external device monitoring function “enabled”. In case of setting the interlock function to “enabled (manual reset)” + *S1 – 24 V DC ±20 % • When the interlock function is set to “Enable (manual reset),” the override function cannot be used. Emitter (Pale purple) Interlock setting input (Pink) Emission halt input / Reset input *S1 K1 K2 0V In case of setting the external device monitoring function to “disabled” Emitter *S1 (Blue) 0 V (Gray / Black) Large multi-purpose indicator input (Receiver side) (Gray) NC BSF4-AH80 *S1 (Yellow-green / Black) Auxiliary output K1, K2: External device (Forced guided relay or magnetic contactor) Switch S1 • Emission halt input / Reset input For automatic reset 0 to +1.5 V (source current 5 mA or less): Emission, Open: Emission halt For manual reset 0 to +1.5 V (source current 5 mA or less): Emission halt, Open: Emission • Muting input A / B, Override input 0 to + 1.5 V (source current 5 mA or less): Valid, Open: Invalid Receiver (Yellow-green) External device monitor input Compact Light Curtain Type 4 ・ 512 SF4B-C SERIES I/O CIRCUIT AND WIRING DIAGRAMS FIBER SENSORS SF4B-□C Cable type PHOTOELECTRIC SENSORS I/O circuit diagrams Emitter Lead wire color 470 Ω 0.22 μF 470 Ω Sensor circuit 0.22 μF (Pale purple) Interlock setting input (Shield) Output polarity setting wire *S1 + – 24 V DC ±10 % Load (Blue) 0 V (Yellow-green / Black) Auxiliary output 470 Ω 0.22 μF 470 Ω (Orange / Black) Synchronization- (Orange / Black) SynchronizationInternal circuit Receiver (Orange) Synchronization+ (Brown) +V WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES (Shield) Output polarity setting wire K1 K2 470 Ω SIMPLE WIRE-SAVING UNITS (Orange / Black) Synchronization- (Brown) +V LASER MARKERS K1 (Black) Control output 1 (OSSD 1) Sensor circuit (Black) Control output 1 (OSSD 1) (White) Control output 2 (OSSD 2) K2 (White) Control output 2 (OSSD 2) K1 (Shield) Output polarity setting wire K2 (Yellow-green) External device monitor input K1 K2 (Blue) 0 V Internal circuit 0.22 μF K1, K2: External device (Forced guided relay or magnetic contactor) Users’ circuit *S1 Switch S1 470 Ω Internal circuit (Blue) 0 V K1, K2: External device (Forced guided relay or magnetic contactor) Users’ circuit *S1 PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Switch S1 • Emission halt input / Reset input For manual reset Vs to Vs – 2.5 V (sink current 5 mA or less): Emission halt (Note) Open: Emission For automatic reset Vs to Vs – 2.5 V (sink current 5 mA or less): Emission (Note) Open: Emission halt • Emission halt input / Reset input For manual reset 0 to +1.5 V (source current 5 mA or less): Emission halt Open: Emission For automatic reset 0 to +1.5 V (source current 5 mA or less): Emission Open: Emission halt • Interlock setting input Vs to Vs – 2.5 V (sink current 5 mA or less): Valid (Note) Open: Invalid • Interlock setting input 0 to +1.5 V (source current 5 mA or less): Valid, Open: Invalid Note: Vs is the applying supply voltage. INDUCTIVE PROXIMITY SENSORS SENSOR OPTIONS Users’ circuit (Orange) Synchronization+ PRESSURE / FLOW SENSORS PARTICULAR USE SENSORS *S1 (Blue) 0 V (Orange) Synchronization+ (Orange / Black) Synchronization- Sensor circuit (Pink) Emission halt input / Reset input 24 V DC ±10 % *S1 (Pale purple) Interlock setting input 0.22 μF (Orange) Synchronization+ Users’ circuit + – (Yellow-green) External device monitor input 0.22 μF LIGHT CURTAINS / SAFETY COMPONENTS Load (Pink) Emission halt input / Reset input *S1 (Shield) Output polarity setting wire Receiver AREA SENSORS (Brown) +V (Yellow-green / Black) Auxiliary output Internal circuit MICRO PHOTOELECTRIC SENSORS Lead wire color (Brown) +V Sensor circuit Emitter LASER SENSORS Selection Guide Light Curtains Safety Components Optical Touch Switch Control Units Definition of Sensing Heights SF4B-C SF4C SF2C SF4B SF2B BSF4-AH80 513 Compact Light Curtain Type 4 ・ I/O CIRCUIT AND WIRING DIAGRAMS FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS SF4B-C SERIES SF4B-□C Cable type Connection examples Interlock function “enabled (manual reset)”, external device monitoring function “enabled” AREA SENSORS Emitter PRESSURE / FLOW SENSORS Receiver LIGHT CURTAINS / SAFETY COMPONENTS (Brown) +V Gray cable INDUCTIVE PROXIMITY SENSORS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS – 24 V DC ±10 % (Pink) Emission halt input / Reset input (Pale purple) Interlock setting input (Yellow-green) External device monitor input K1 K2 Open (Brown) +V (Black) Control output 1 (OSSD 1) K1 (White) Control output 2 (OSSD 2) In case of setting the external device monitoring function to “disabled” K2 (Shield) Output polarity setting wire (Blue) 0 V Emitter K1, K2: External device (Forced guided relay or magnetic contactor) *S1 (Yellow-green / Black) Auxiliary output Switch S1 • Emission halt input / Reset input For manual reset Vs to Vs – 2.5 V (sink current 5 mA or less): Emission halt (Note) Open: Emission For automatic reset Vs to Vs – 2.5 V (sink current 5 mA or less): Emission (Note) Open: Emission halt • Interlock setting input Vs to Vs – 2.5 V (sink current 5 mA or less): Valid (Note) Open: Invalid Receiver (Yellow-green) External device monitor input Note: Vs is the applying supply voltage. Emitter Receiver Gray cable The diagram at left shows the configuration when using NPN output, interlock function “enabled (manual reset)” and external device monitoring function “enabled”. (Brown) +V (Yellow-green / Black) Auxiliary output (Shield) Output polarity setting wire Safety Components (Pink) Emission halt input / Reset input (Pale purple) Interlock setting input + *S1 – 24 V DC ±10 % (Pale purple) Interlock setting input Gray cable (with black line) (Brown) +V (Black) Control output 1 (OSSD 1) (Shield) Output polarity setting wire SF4B-C *S1 K1 K2 (Blue) 0 V SF4C Open (Pink) Emission halt input / Reset input (Yellow-green) External device monitor input K1 K2 (White) Control output 2 (OSSD 2) 0V In case of setting the external device monitoring function to “disabled” Emitter K1, K2: External device (Forced guided relay or magnetic contactor) SF2C BSF4-AH80 Emitter Load (Orange / Black) Synchronization(Orange) Synchronization+ Optical Touch Switch SF2B In case of setting the interlock function to “disabled (automatic reset)” (Blue) 0 V (Orange) Synchronization+ (Orange / Black) Synchronization- Light Curtains SF4B +24 V DC (Orange) Synchronization+ Gray cable (with black line) Selection Guide Definition of Sensing Heights Emitter *S1 Lead wire color Control Units In case of setting the interlock function to “disabled (automatic reset)” (Orange / Black) Synchronization- MEASUREMENT SENSORS ENERGY CONSUMPTION VISUALIZATION COMPONENTS + Load (Orange / Black) Synchronization- WIRE-SAVING SYSTEMS HUMAN MACHINE INTERFACES (Yellow-green / Black) Auxiliary output (Orange) Synchronization+ SIMPLE WIRE-SAVING UNITS PLC (Pink) Emission halt input / Reset input (Blue) 0 V SENSOR OPTIONS LASER MARKERS *S1 (Pale purple) Interlock setting input (Shield) Output polarity setting wire PARTICULAR USE SENSORS STATIC ELECTRICITY PREVENTION DEVICES The diagram at left shows the configuration when using PNP output, interlock function “enabled (manual reset)” and external device monitoring function “enabled”. Lead wire color *S1 Switch S1 • Emission halt input / Reset input For manual reset 0 to +1.5 V (source current 5 mA or less): Emission halt Open: Emission For automatic reset 0 to +1.5 V (source current 5 mA or less): Emission Open: Emission halt • Interlock setting input 0 to +1.5 V (source current 5 mA or less): Valid, Open: Invalid (Yellow-green / Black) Auxiliary output Receiver (Yellow-green) External device monitor input Compact Light Curtain Type 4 ・ 514 SF4B-C SERIES I/O CIRCUIT AND WIRING DIAGRAMS FIBER SENSORS LASER SENSORS SF-C13 SF4B-□C wiring diagrams (Control Category 4) PHOTOELECTRIC SENSORS For PNP output (minus ground) For NPN output (plus ground) • Connect the light curtain control outputs OSSD 1 and OSSD 2 to S1 and S2 respectively. • Connect the light curtain control outputs OSSD 1 and OSSD 2 to S4 and S2 respectively and ground the + side. Emitter Emitter Receiver Cable color: Gray Synchronization+ (Orange) Synchronization(Orange / Black) +V (Brown) +24 V DC Load 0 V (Blue) Synchronization+ (Orange) Synchronization(Orange / Black) +V (Brown) +24 V DC Emission halt input / Auxiliary output Interlock setting input (Pale purple) Reset input Yellow-green / Black Open +V (Brown) (Pink) Output polarity setting wire (Shield) 0 V (Blue) Output polarity Emission Auxiliary output Interlock setting input (Pale purple) setting wire halt input / Yellow-green (Shield) Reset input / Black Open (Pink) +V (Brown) 0 V (Blue) Load Output polarity setting wire (Shield) S1 S2 S3 (Note 1) S4 X1 X2 X3 F FUSE1 13 23 (Note 1) FUSE2 33 41 A1 F.G. S1 S2 S3 S4 X1 X2 F A2 0V F.G. KA, KB: External device (Forced guided relay or magnetic contactor) KA N 33 41 PLC RESET (Note 1, 2) HUMAN MACHINE INTERFACES K2 FAULT 14 24 AUX LASER MARKERS FUSE2 SF-C13 control circuit K2 INTER_LOCK FUSE1 X3 13 23 K1 Ui SF-C13 control circuit OUT STATIC ELECTRICITY PREVENTION DEVICES L1 K1 Ui MEASUREMENT SENSORS OSSD 1 (Black) OSSD 2 (White) A1 WIRE-SAVING SYSTEMS OSSD 2 (White) L1 34 42 L1L2L3 KB OUT KB KA M 3 Notes: 1) The above diagram is when using manual reset. If automatic reset is used, disconnect the lead from X2 and connect it to X3. In this case, a reset (RESET) button is not needed. 2) Use a momentary-type switch as the reset (RESET) button. A2 INTER_LOCK AUX 0V KA, KB: External device (Forced guided relay or magnetic contactor) PARTICULAR USE SENSORS SIMPLE WIRE-SAVING UNITS Output polarity setting wire (Shield) External device monitor input (Yellow-green) OSSD 1 (Black) INDUCTIVE PROXIMITY SENSORS SENSOR OPTIONS 0 V (Blue) External device monitor input (Yellow-green) RESET (Note 1, 2) PRESSURE / FLOW SENSORS Cable color: Gray with black line Cable color: Gray AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS Receiver Cable color: Gray with black line MICRO PHOTOELECTRIC SENSORS FAULT 14 24 KA N 34 42 L1L2L3 KB KB KA M 3 Notes: 1) The above diagram is when using manual reset. If automatic reset is used, disconnect the lead from X2 and connect it to X3. In this case, a reset (RESET) button is not needed. 2) Use a momentary-type switch as the reset (RESET) button. ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Terminal arrangement diagram A1 A2 S1 S2 S3 S4 AUX X1 X2 X3 13 14 23 24 33 34 41 42 Terminal Description A1 +24 V DC A2 0V S1 to S4 AUX Light curtain control output (OSSD) input terminal Semiconductor auxiliary output X1 Reset output terminal X2 Reset input terminal (Manual) X3 Reset input terminal (Automatic) 13-14, 23-24, 33-34 Enabling path (NO contact × 3) 41-42 Auxiliary output (NC contact × 1) A terminal block is required for wiring of light curtain side. Selection Guide Light Curtains Safety Components Optical Touch Switch Control Units Definition of Sensing Heights SF4B-C SF4C SF2C SF4B SF2B BSF4-AH80 515 ・ FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES Compact Light Curtain Type 4 MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Light Curtains Safety Components Optical Touch Switch Control Units Definition of Sensing Heights SF4B-C SF4C SF2C SF4B SF2B BSF4-AH80 Refer to the instruction manual for details. The instruction manual can be downloaded from our website. PRECAUTIONS FOR PROPER USE Wiring Emission halt function Refer to the applicable regulations for the region where this device is to be used when setting up the device. In addition, make sure that all necessary measures are taken to prevent possible dangerous operating errors resulting from earth faults. • Make sure to carry out the wiring in the power supply off condition. • Verify that the supply voltage variation is within the rating. • If power is supplied from a commercial switching regulator, ensure that the frame ground (F.G.) terminal of the power supply is connected to an actual ground. • In case noise generating equipment (switching regulator, inverter motor, etc.) is used in the vicinity of this sensor, connect the frame ground (F.G.) terminal of the equipment to an actual ground. • Do not run the wires together with high-voltage lines or power lines or put them in the same raceway. This can cause malfunction due to induction. Interlock function • The selection of manual reset / automatic reset is available by applying the interlock input (pale purple) wiring. The interlock becomes available by selecting manual reset. Interlock setting input wire (pale purple) Interlock function When selecting PNP output: Connected to +V When selecting NPN output: Connected to 0 V Manual reset Open Automatic reset ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS SF4B-C SERIES In case of using the interlock function, be sure there exists no operator inside of the dangerous area. It causes death or serious injury without the confirmation. Manual reset • The control outputs (OSSD 1, OSSD 2) are not turned ON automatically even though this device is received the light. When this device is reset in light received state [open the emission halt input / reset input → short-circuit the device to 0 V or +V → open], the control outputs (OSSD 1, OSSD 2) are turned ON. The reset switch shall be placed in area where all over the dangerous zone shall be comprehend and out side of the dangerous zone. Automatic reset • The control outputs (OSSD 1, OSSD 2) are turned ON automatically when this device receives the light. Emitter +24 V DC (or 0 V) • This function stops the emission process of the emitter. You can select whether emission is on or halted by means of the connection status for the emission halt input / reset input wire (pink). Interlock function Manual reset Automatic reset Emission halt input / Reset input wire (pink) Emission halt input Control output status (OSSD 1, OSSD 2) Open When selecting PNP output: Connected to +V When selecting NPN output: Connected to 0 V Open When selecting PNP output: Connected to +V When selecting NPN output: Connected to 0 V Invalid ON Valid OFF Valid OFF Invalid ON • During emission halt, the control outputs (OSSD 1, OSSD 2) become OFF status. • By using this function, malfunction due to extraneous noise or abnormality in the control outputs (OSSD 1, OSSD 2) and the auxiliary output can be determined even from the machinery side. • Normal operation is restored when the emission halt input / reset input wire (pink) is connected to 0 V or +V (for manual reset: open). Do not use the emission halt function for the purpose of stopping the machine in which the SF4B-C series is installed. Failure to do so could result in death or serious injury. External device monitoring function • This is the function for checking whether the external safety relay connected to the control outputs (OSSD 1, OSSD 2) perform normally in accordance with the control outputs (OSSD 1, OSSD 2) or not. Monitor the contacting point “b” of the external safety relay, and if any abnormality such as deposit of the contacting point, etc. is detected, change the status of the light curtain into lockout one, and turn OFF the control outputs (OSSD 1, OSSD 2). In case of setting the external device monitoring function to enabled • Connect the external device monitoring input (yellowgreen) to the external safety relay connected the control outputs (OSSD 1, OSSD 2). In case of not using the external device monitoring function • Connect the external device monitoring input (yellowgreen) to the auxiliary output (yellow-green / black). At this time, set the auxiliary output as [negative logic of control outputs (OSSD 1, OSSD 2)] (factory setting). • The auxiliary output cannot be connected to external devices. Emitter Receiver Emission halt input / Reset input (Pink) Interlock setting input (Pale purple) Open In case that this light curtain is used under automatic reset mode, set the system not to be auto reset by the safety relay unit, etc. (conforming to EN 60204-1) • It is possible to change the conditions for interlocking by using the handy-controller SFB-HC (optional). Refer to instruction manual enclosed with this product for details. Auxiliary output (Yellow-green / Black) External device monitor input (Yellow-green) • It is also possible to set the external device monitoring function into invalid by using the handy-controller SFB‑HC (optional). Refer to instruction manual enclosed with this product for details. Compact Light Curtain Type 4 Refer to the instruction manual for details. The instruction manual can be downloaded from our website.・ PRECAUTIONS FOR PROPER USE Auxiliary output (Non-safety output) Normal mode Auxiliary output setting Negative logic of OSSD (Factory setting) Control outputs Emission (OSSD 1, OSSD 2) status Lockout halt Beam Beam received interrupted ON OFF ON ON • Incorrect use of the muting control may cause accidents. Please understand the muting control fully, and use it. As for the muting control, the following international standards define the requirements. ISO 13849-1 (EN ISO 13849-1 / JIS B 9705-1) IEC 61496-1 (ANSI / UL 61496 / JIS B 9704-1) IEC 60204-1 (JIS B 9960-1) EN 415-4 ANSI B11.19-1990 ANSI/RIA R15.06-1999 • Use the muting control while the machine cycle is not in danger mode. Maintain safety with the other measure while the muting control is activated. • For the application that the muting control is activated when a workpiece passes through the sensor, place the muting sensor so that the conditions for the muting control cannot be satisfied by intrusion of personnel when the workpiece is passing through the sensor or the workpiece is not passing through it. • Be sure to check the operation of the muting function before its use. • This function turns the safety function of this light curtain into disabled temporarily. When the control outputs (OSSD 1, OSSD 2) are ON, this function is available for passing the workpiece through the sensing area of the light curtain without stopping the machinery. The muting function becomes valid when all the conditions listed below are satisfied. (1) The control outputs (OSSD 1, OSSD 2) shall be ON. (2)  The output of the muting sensors A and B shall be changed from OFF (open) to ON. At this time, the time difference occurred by changing the output of the muting sensors A and B into ON status shall be within 0.03 to 3 sec. (Note 1) • The following devices, photoelectric sensor with semiconductor output, inductive proximity sensor, position switch on N.O. (Normally open) contact, etc. are available for applying to the muting sensor. Notes: 1) 0 to 3 sec. is allowable by using the handy controller Ver. 2.1 (SFB-HC) (optional) and connecting N.O. (Normally Open) type muting sensor to the input A, as well as connecting N.C. (Normally Closed) type muting sensor to the input B. 2) The muting indicator diagnosis function can be set with the handy controller Ver. 2 or later (SFB-HC) (optional), but it must be set to invalid. If the muting indicator diagnosis function is set to valid, the muting function cannot be used. FIBER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS Gray cable Do not use the auxiliary output for the purpose of stopping the device with SF4B-C installed. Failure to do so could result in serious injury or death. Muting Function (For SF4B-□CA-J05 only) 516 LASER SENSORS • To trigger a large multi-purpose indicator during muting operation, connect the wiring as follows: As for lead wires other than below, perform wiring depending on your application. Emitter • This light curtain incorporates the auxiliary output (yellowgreen / black) for the non-safety output. The auxiliary output is incorporated with the emitter. Receiver ・ SF4B-C SERIES (Gray / Black) Large multi-purpose indicator input (Emitter side) (Red) Muting auxiliary output (Brown) +V + (Blue) 0 V – 24 V DC ±10 % (Orange) Synchronization+ (Orange / Black) SynchronizationGray cable (with black line) (Orange / Black) Synchronization(Orange) Synchronization+ (Brown) +V (Blue) 0 V (Gray / Black) Large multi-purpose indicator input (Receiver side) Override function (For SF4B-□CA-J05 only) • This function sets the safety function of this light curtain enabled forcibly. When using the muting function, the override function can be used to start the machinery at times such as when the control outputs (OSSD 1 and OSSD 2) are OFF or when the muting sensors are ON when the line is to be started. The override function becomes valid when all the conditions listed below are satisfied. (1) The signal shall be input to either muting sensor A, B, or A and B. (2) The override input (yellow) shall be short-circuited to 0 V or +V, and the emission halt input / reset input (pink) shall be opened. (3 sec. continuously) If one of the two conditions above becomes invalid or timing exceeds 60 sec. (Note 1), the override function becomes invalid. PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS • The override function only operates when the interlock function is disabled (automatic reset). Notes: 1) By using handy-controller (SFB-HC) (optional) Ver.2.1 or later, a change between 60 and 600 sec. by 10 sec. per unit is possible. 2) The muting indicator diagnosis function can be set with the handy controller Ver. 2 or later (SFB-HC) (optional), but it must be set to invalid. If the muting indicator diagnosis function is set to valid, the muting function cannot be used. 3) The override function only operates when the interlock function is disabled (automatic reset). • Make sure manually to operate system for starting override function. Furthermore, the system shall be placed in area where all over the dangerous zone shall be comprehend and out side of the dangerous zone. • Using override function, make sure that there exist no operator in the dangerous zone, which may result in death or serious injury. Selection Guide Light Curtains Safety Components Optical Touch Switch Control Units Definition of Sensing Heights SF4B-C SF4C SF2C SF4B SF2B BSF4-AH80 Compact Light Curtain Type 4 ・ FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS Others • When this device is used in the “PSDI mode”, an appropriate control circuit must be configured between this device and the machinery. For details, be sure to refer to the standards or regulations applicable in each region or country. • To use this product in the U.S.A., refer to OSHA 1910. 212 and OSHA 1910. 217 for installation, and in Europe, refer to EN 999 as well. Observe your national and local requirements before installing this product. PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS • This catalog is a guide to select a suitable product. Be sure to read instruction manual attached to the product prior to its use. • Both emitter and receiver are combined adjusted on factory setting, please apply both emitter and receiver with the same serial No. The serial No. is indicated on the plates of both emitter and receiver. (Indicated under model No.) • Make sure to carry out the test run before regular operation. • Do not use this product with machinery that cannot be stopped immediately during the operating cycle by means of an emergency stop system. Sensing area • Make sure to install this product such that any part of the human body must pass through its sensing area in order to reach the dangerous parts of the machinery. Furthermore, ensure that some part of the operator’s body always remains in the sensing area when operation is done with the dangerous parts of the machine. If the human body is not detected, there is a danger of serious injury or death. • Do not use any reflection type or recursive reflection type arrangement. • Multiple receivers (emitters) cannot be connected to one emitter (receiver). FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Light Curtains Safety Components Optical Touch Switch Influence of reflective surfaces • Do not use during the initial transient time (2 sec.) after the power supply is switched on. • Avoid dust, dirt and steam. • Take care that the light curtain does not come in direct contact with water, oil, grease, or organic solvents, such as, thinner, etc. • Take care that the light curtain is not directly exposed to fluorescent light from a rapid-starter lamp or a high frequency lighting device, as it may affect the sensing performance. INDUCTIVE PROXIMITY SENSORS MEASUREMENT SENSORS Example of correct installation Dangerous part Sensing area Protective structure Control Units Definition of Sensing Heights SF4B-C Dangerous part SF4C Sensing area SF2C SF4B SF2B BSF4-AH80 Refer to the instruction manual for details. The instruction manual can be downloaded from our website.・ PRECAUTIONS FOR PROPER USE PRESSURE / FLOW SENSORS WIRE-SAVING SYSTEMS SF4B-C SERIES Example of incorrect installation Dangerous part Sensing area Install the light curtain by considering the effect of nearby reflective surfaces, and take countermeasures such as painting, masking, or changing the material of the reflective surface, etc. Failure to do so may cause the light curtain not to detect, resulting in serious body injury or death. • Install this device at a distance of at least A (m) (given below) away from reflective surfaces such as metal walls, floors, ceilings, workpiece, covers, panels or glass surfaces. Side view Top view Reflective ceiling Emitter A Reflective surface Receiver Emitter θ θ A Receiver Sensing range L Sensing range L A Reflective floor Distance between emitter and receiver Setting distance L 0.3 to 3 m 0.984 to 9.843 ft 3 to 7 m 9.843 to 22.966 ft 0.5 1.640 Allowable installation distance A Allowable installation distance A (m ft) 517 0.4 1.312 0.3 0.984 0.2 0.656 0.16 m 0.525 ft L/2 × tan2θ = L/2 × 0.105 (m) 0.344 (ft) (θ = 3°) 0.1 0.328 0 Install in this area Do not install in this area 1 3 5 7 3.281 9.843 16.404 22.966 Sensing range L (m ft) Note: The effective aperture angle for this device is ±2.5° or less (when L > 3 m 9.843 ft) as required by IEC 61496-2, ANSI/UL 61496-2. However, install this device away from reflective surfaces considering an effective aperture angle of ±3° to take care of beam misalignment, etc. during installation. Handy-controller This device enables to set each function using the handy-controller SFB-HC (optional). Among the functions, the contents related to the safety distance such as the size of the minimum sensing object and response time are varied depending on the setting condition. When setting each function, re-calculate the safety distance, and make enough space larger than the calculated safety distance. Failure to do so might cause the accident that the device cannot stop quickly before reaching the dangerous area of the machinery, resulting in the serious injury or death. Dangerous part • Refer to the instruction manual enclosed with the handy-controller for details of the function settings for using handy-controller SFB-HC (optional). Sensing area 9 29.528 Compact Light Curtain Type 4 ・ PRECAUTIONS FOR PROPER USE Safety distance • Calculate the safety distance correctly, and always maintain a distance which is equal to or greater than the safety distance, between the sensing area of this light curtain and the dangerous parts of the machinery. (Please check the latest standards for the equation.) If the safety distance is miscalculated or if sufficient distance is not maintained, there is a danger of serious injury or death. • Before designing the system, refer to the relevant standards of the region where this device is to be used and then install this device. Dangerous part of machine Emitter S Beam axis Receiver S: Safety distance The sizes of the minimum sensing objects for this device vary depending on whether or not the floating blanking function is being used. Calculate the safety distance with the proper size of the minimum sensing object and appropriate equation. Size of minimum sensing object when applying floating blanking function Invalid Setting (Note) 1 beam 2 beam 3 beam channel channels channels SF4B-H□C(A-J05) Min. sensing object ø25 mm ø0.984 in ø25 mm ø0.984 in ø45 mm ø1.772 in ø65 mm ø85 mm ø2.559 in ø3.346 in SF4B-H□C(A-J05) Min. sensing object ø45 mm ø1.772 in ø45 mm ø1.772 in ø85 mm ø3.346 in ø125 mm ø165 mm ø4.921 in ø6.496 in Note: Refer to P. 501 for details of the floating blanking function. • Safety distance is calculated based on the following equation when a person moves perpendicular (normal intrusion) to the sensing area of the light curtain. In case the intrusion direction is not perpendicular to the sensing area, be sure to refer to the relevant standard (regional standard, specification of the machine, etc.) for details of the calculation. For use in Europe (EU) (as EN 999) (Also applicable to ISO 13855 / JIS B 9715) For intrusion direction perpendicular to the sensing area • Equation S=K×T+C S: Safety distance (mm) Minimum required distance between the sensing area surface and the dangerous parts of the machine K: Intrusion velocity of operator’s body or object (mm/sec.) Taken as 2,000 (mm/sec.) for calculation T: Response time of total equipment (sec.) T = Tm + TSF4B Tm: Maximum halting time of machinery (sec.) TSF4B: Response time of the SF4B-C series (sec.) C: Additional distance calculated from the size of the minimum sensing object of the SF4B-C series (mm) However, the value of “C” cannot be under 0. C = 8 × (d - 14) d: Minimum sensing object diameter (mm) SF4B-C SERIES 518 Refer to the instruction manual for details. The instruction manual can be downloaded from our website.・ • For calculating the safety distance “S”, there are the following five cases. First calculate by substituting the value K = 2,000 (mm/sec.) in the equation above. Then, classify the obtained value of “S” into three cases, 1) S < 100, 2) 100 ≤ S ≤ 500, and 3) S > 500. For Case 3) S > 500, recalculate by substituting the value K = 1,600 (mm/sec.). After that, classify the calculation result into two cases, 4) S ≤ 500 and 5) S > 500. For details, refer to the instruction manual enclosed with this product. • When this product is used in the “PSDI mode”, an appropriate safety distance “S” must be calculated. For details, be sure to refer to the standards or regulations applicable in each region or country. • Equation S=K×T+C S: Safety distance (mm) K: Intrusion velocity of operator’s body or object (mm/sec.) Taken as 1,600 (mm/sec.) for calculation T: Response time of total equipment (sec.) T = Tm + TSF4B Tm: Maximum halting time of machinery (sec.) TSF4B: Response time of the SF4B-C series (sec.) C: Additional distance calculated from the size of the minimum sensing object of the SF4B-C series (mm) C = 850 (mm) (Constant) For use in the United States of America (as per ANSI/RIA 15.06) • Equation S = K × (TS + TC + TSF4B + Tbm) + Dpf S: Safety distance (mm) Minimum required distance between the sensing area surface and the dangerous parts of the machine K: Intrusion velocity {Recommended value in OSHA is 63 (inch/s) [≈ 1,600 (mm/sec.)] } ANSI/RIA 15.06 does not define the intrusion speed “K”. When determining K, consider possible factors including physical ability of operators. TS: Halting time calculated from the operation time of the control element (air valve, etc.) (sec.) TC: Maximum response time of the control circuit required for functioning the brake (sec.) TSF4B: Response time of the SF4B-C series (sec.) Tbm: Additional halting time tolerance for the brake monitor (sec.) The following equation holds when the machine is equipped with a brake monitor. Tbm = Ta - (TS + TC) Ta: Setting time of brake monitor (sec.) When the machine is not equipped with a brake monitor, it is recommended that 20 % or more of (TS + TC) is taken as additional halting time. Dpf: Additional distance calculated from the size of the minimum sensing object of the device (mm) SF4B-H□C(A-J05): Dpf = 61.2 mm 2.409 in SF4B-A□C(A-J05): Dpf = 129.2 mm 5.087 in Dpf = 3.4 × (d - 0.276) (inch) ≈ 3.4 × (d - 7) (mm) d: Minimum sensing object diameter 0.985 (inch) ≈ 25 (mm) [SF4B-H□C(A-J05)] Minimum sensing object diameter 1.772 (inch) ≈ 45 (mm) [SF4B-A□C(A-J05)] • When the floating blanking function is applied, the minimum sensing object becomes large. According to ANSI/RIA 15.06, Dpf = 900 mm (3 ft) when d > 64 mm (2.5 inches). FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Light Curtains Safety Components Optical Touch Switch Control Units Definition of Sensing Heights SF4B-C SF4C SF2C SF4B SF2B BSF4-AH80 519 ・ FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Compact Light Curtain Type 4 DIMENSIONS (Unit: mm in) SF4B-□CA-J05 SF4B-□C B SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES 6 × M3 mounting hole for countersunk screw 27.4 1.079 5 0.197 6 × M3 mounting holeF for countersunk screw 20 0.787 B 5 0.197 33 1.299 2 0.079 2 0.079 2 0.079 F (3.2 0.126) 2 0.079 10.7 0.421 E (46.6 1.835) 5.4 0.213 (2 0.079) 2 0.079 10.7 0.421 108 4.252 120 A 4.724 C 19.6 0.772 29.9 1.177 120 A C 4.724 Beam pitch ø5 ø0.197 Gray cable 21.6 0.850 H Beam pitch ø5 ø0.197 Gray cable 21.6 0.850 5.4 0.213 11.8 0.465 10 0.394 21.6 0.850 (45 1.772)No. Model SF4B-H12C(A-J05) SF4B-H16C(A-J05) ø15.6 ø0.614 SF4B-A8C(A-J05) SF4B-A12C(A-J05) SF4B-H28C(A-J05) SF4B-H32C(A-J05) SF4B-A16C(A-J05) SF4B-H36C(A-J05) Control Units SF4B-H40C(A-J05) SF4B-A20C(A-J05) SF4B-H48C(A-J05) SF4B-A24C(A-J05) SF4B-C SF4B-H56C(A-J05) SF4B-A28C(A-J05) SF4C SF4B-H64C(A-J05) SF4B-A32C(A-J05) SF4B-H72C(A-J05) SF4B-A36C(A-J05) SF4B-H80C(A-J05) SF4B-A40C(A-J05) SF4B-H88C(A-J05) SF4B-A44C(A-J05) SF4B-H96C(A-J05) SF4B-A48C(A-J05) SF2B BSF4-AH80 29.9 1.177 10.7 2 0.421 0.079 Receiver ø15.6 ø0.614 Optical Touch Switch SF4B F 5.4 0.213 3.2 0.465 11.8 10 0.394 0.126 29.9 21.6 0.850 1.177 E 5.4 0.213 ø5 ø0.197 Gray cable (with black line) (46.6 1.835) 2 0.079 G ø5 ø0.197 Gray cable (with black line) B (45 1.772) SF4B-H24C(A-J05) SF2C 2 0.079 G 5 2 0.197 0.079 Model No. G H SF4B-H□C(A-J05) 21.7 0.854 20 0.787 SF4B-A□C(A-J05) 41.7 1.642 40 1.575 A B C 294.4 11.591 374.4 14.740 454.4 17.890 534.4 21.039 614.4 24.189 694.4 27.339 774.4 30.488 854.4 33.638 1,014.4 39.937 1,174.4 46.236 1,334.4 52.535 1,494.4 58.835 1,654.4 65.134 1,814.4 71.433 1,974.4 77.732 279 10.984 359 14.134 439 17.283 519 20.433 599 23.583 679 26.732 759 29.882 839 33.031 999 39.331 1,159 45.630 1,319 51.929 1,479 58.228 1,639 64.528 1,799 70.827 1,959 77.126 263.4 10.370 343.4 13.520 423.4 16.669 503.4 19.819 583.4 22.969 663.4 26.118 743.4 29.268 823.4 32.417 983.4 38.717 1,143.4 45.016 1,303.4 51.315 1,463.4 57.614 1,623.4 63.913 1,783.4 70.212 1,943.4 76.512 D SF4B-H□C(A-J05) SF4B-A□C(A-J05) 220 8.661 — 300 11.811 380 14.961 460 18.110 540 21.260 620 24.409 700 27.559 780 30.709 760 29.921 940 37.008 920 36.220 1,100 43.307 1,080 42.520 1,260 49.606 1,240 48.819 1,420 55.906 1,400 55.118 1,580 62.205 1,560 61.417 1,740 68.504 1,720 67.716 1,900 74.803 1,880 74.016 280 11.024 — 440 17.323 — 600 23.622 — E F — — — — — — — — — — — — — — 395 15.551 475 18.701 555 21.850 415 16.339 468 18.425 521 20.512 574 22.598 627 24.685 F 3.2 0.126 SF4B-H20C(A-J05) Definition of Sensing Heights 5 0.197 2 0.079 (46.6 1.835) 108 4.252 5.4 0.213 10 0.394 11.8 0.465 H 33 1.299 H D Emitter MACHINE VISION SYSTEMS Safety Components 33 1.299 D 108 4.252 FA COMPONENTS Light Curtains 27.4 120 A 1.079 C 4.724 2 0.079 20 0.787 H (46.6 1.835) G 5.4 0.213 10 0.394 11.8 0.465 ENERGY CONSUMPTION VISUALIZATION COMPONENTS Selection Guide 20 0.787 Protective height G 29.9 1.177 120 A 4.724 C D 19.6 0.772 (3.2 0.126) 33 1.299 D 5.4 0.213 (2 0.079) 108 4.252 E HUMAN MACHINE INTERFACES UV CURING SYSTEMS 27.4 1.079 2 0.079 Protective height MS-SF4BC-5 LASER MARKERS PLC 2 0.079 The figure depicts rear mounting using the standard mounting bracket MS-SF4BC-1(optional) and the intermediate supporting bracket for 19.6 19.6 0.772 0.772 standard mounting bracket MS-SF4BC-5(optional). MS-SF4BC-5 LIGHT CURTAINS / SAFETY COMPONENTS PARTICULAR USE SENSORS Light curtain MS-SF4BC-1 27.4 1.079 20 0.787 MS-SF4BC-1 INDUCTIVE PROXIMITY SENSORS The CAD data in the dimensions can be downloaded from our website.・ Assembly dimensions AREA SENSORS PRESSURE / FLOW SENSORS SF4B-C SERIES — — — 854 33.622 961 37.835 1,068 42.047 1,175 46.260 1,282 50.472 5.4 0.213 10.7 2 0.421 0.079 E Compact Light Curtain Type 4 ・ DIMENSIONS (Unit: mm in) SF4B-□CA-J05 SF4B-□C The CAD data in the dimensions can be downloaded from our website.・ Light curtain MS-SF4BC-1 (2 0.079) (2 0.079) Assembly dimensions 27.4 1.079 The figure depicts side mounting using the standard mounting standard mounting bracket MS-SF4BC-5(optional). 19.6 0.772 bracket 27.4 1.079 (2 0.079) 27.4 1.079 B 5 0.197 20 0.787 25 6 × M3 mounting hole K 0.984 for countersunk screw 3 D 0.118 5 0.197 J 108 4.252 20 0.787 MS-SF4BC-5 B 5 0.197 20 0.787 25 K 0.984 J 15 0.591 10.7 0.421 29.9 1.177 11.8 0.465 19.6 0.772 27.4 1.079 C A (2 0.079) H A Beam pitch G H SAFETY 5 0.197 COMPONENTS 2 INDUCTIVE 0.9 15 0.591 PROXIMITY SENSORS B (46.6 1.835) 5 0.197 (3 0.118) PARTICULAR 21.6 0.850 Emitter 20 0.787 15 0.591 2 0.079 ø5 ø0.197 Gray cable (with black line) (3 0.118) (46.6 1.835) WIRE-SAVING SYSTEMS 10.7 0.421 Receiver HUMAN MACHINE INTERFACES ø15.6 ø0.614 SF4B-H12C(A-J05) SF4B-H16C(A-J05) ø15.6 ø0.614 SF4B-A8C(A-J05) SF4B-H20C(A-J05) SF4B-H24C(A-J05) SF4B-A12C(A-J05) SF4B-H28C(A-J05) SF4B-H32C(A-J05) SF4B-A16C(A-J05) SF4B-H36C(A-J05) SF4B-H40C(A-J05) SF4B-A20C(A-J05) SF4B-H48C(A-J05) SF4B-A24C(A-J05) SF4B-H56C(A-J05) SF4B-A28C(A-J05) SF4B-H64C(A-J05) SF4B-A32C(A-J05) SF4B-H72C(A-J05) SF4B-A36C(A-J05) SF4B-H80C(A-J05) SF4B-A40C(A-J05) SF4B-H88C(A-J05) SF4B-A44C(A-J05) SF4B-H96C(A-J05) SF4B-A48C(A-J05) Model No. G H SF4B-H□C(A-J05) 21.7 0.854 20 0.787 SF4B-A□C(A-J05) 41.7 1.642 40 1.575 STATIC ELECTRICITY PREVENTION DEVICES PLC (45 1.772) No. MEASUREMENT SENSORS LASER MARKERS (45 1.772) Model USE 20 0.787 SENSOR OPTIONS 25 0.984 K 10 11.8 0.465 0.394 SIMPLE 29.9 WIRE-SAVING 21.6 0.850 UNITS1.177 J 10 11.8 0.465 0.394 29.9 21.6 0.850 1.177 ø5 ø0.197 Gray cable (with black line) ENERGY CONSUMPTION VISUALIZATION COMPONENTS A B C 294.4 11.591 374.4 14.740 454.4 17.890 534.4 21.039 614.4 24.189 694.4 27.339 774.4 30.488 854.4 33.638 1,014.4 39.937 1,174.4 46.236 1,334.4 52.535 1,494.4 58.835 1,654.4 65.134 1,814.4 71.433 1,974.4 77.732 279 10.984 359 14.134 439 17.283 519 20.433 599 23.583 679 26.732 759 29.882 839 33.031 999 39.331 1,159 45.630 1,319 51.929 1,479 58.228 1,639 64.528 1,799 70.827 1,959 77.126 263.4 10.370 343.4 13.520 423.4 16.669 503.4 19.819 583.4 22.969 663.4 26.118 743.4 29.268 823.4 32.417 983.4 38.717 1,143.4 45.016 1,303.4 51.315 1,463.4 57.614 1,623.4 63.913 1,783.4 70.212 1,943.4 76.512 FA COMPONENTS D SF4B-H□C(A-J05) SF4B-A□C(A-J05) 8.661 220 — 300 11.811 380 14.961 460 18.110 540 21.260 620 24.409 700 27.559 780 30.709 760 29.921 940 37.008 920 36.220 1,100 43.307 1,080 42.520 1,260 49.606 1,240 48.819 1,420 55.906 1,400 55.118 1,580 62.205 1,560 61.417 1,740 68.504 1,720 67.716 1,900 74.803 1,880 74.016 280 11.024 — 440 17.323 — 50 PRESSURE / 2 FLOW 0.7 SENSORS 20 0.787 G 5.4 0.213 ø5 ø0.197 Gray cable (2 SENSORS G 5.4 0.213 108 4.252 ø5 ø0.197 Gray cable LIGHT CURTAINS / D 5 0.197 H PHOTOELECTRIC AREA SENSORS 108 4.252 D LASER SENSORS MICRO PHOTOELECTRIC SENSORS (2 0.079) 27.4 A C 120 1.079 4.724 C 120 4.724 FIBER SENSORS 27.4 SENSORS 1.079 bracket for 2 0.079 10 0.394 11.8 0.465 29.9 21.6 0.850 1.177 H Beam (46.6 1.835) pitch G 5.4 0.213 10 0.394 120 4.724 10.7 0.4212 0.079 3 0.118 (2 0.079) Protective height 6 × M3 mounting hole for countersunk screw 19.6 D 0.772 5 0.197 27.4 108 1.079 4.252 20 0.787 Protective height 15 0.591 2 0.079 120 4.724 A C (46.6 1.835) 5.4 0.213 19.6 0.772 supporting 27.4 1.079 MS-SF4BC-1(optional) and the intermediate MS-SF4BC-5 MS-SF4BC-1 (2 0.079) 520 SF4B-C SERIES 600 23.622 — J K — — — — — — — — — — — — — — 390 15.354 470 18.504 550 21.654 410 16.142 463 18.228 516 20.315 569 22.402 622 24.488 — — MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Light Curtains Safety Components Optical Touch Switch Control Units Definition of Sensing Heights — SF4B-C 849 33.425 956 37.638 1,063 41.850 1,170 46.063 1,277 50.275 SF4C SF2C SF4B SF2B BSF4-AH80 1 521 Compact Light Curtain Type 4 ・ DIMENSIONS (Unit: mm in) FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS SF4B-C SERIES SF4B-□CA-J05 The CAD data in the dimensions can be downloaded from our website.・ SF4B-□C Light curtain Assembly dimensions The figure depicts rear mounting using the rear utility mounting bracket MS-SF4BC-2(optional) and the intermediate supporting bracket for utility mounting bracket MS-SF4BC-4(optional). AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS 19.6 0.772 (4.2 0.165) MS-SF4BC-2 19.6 0.772 (4.2 0.165) (4.2 0.165) MS-SF4BC-2 PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS B B 19.6 19.6 0.772 0.772 32.2 32.2 1.268 1.268 10.8 0.425 120 M 4.724 D L 0.417 10.6 MS-SF4BC-4 108 4.252 4 0.157 10.6 0.417 MS-SF4BC-4 4 0.157 32.2 1.268 10.8 0.425 5.4 0.213 5.4 0.213 (4.2 0.165) 19.6 0.772 Protective height L D M 108 4.252 LASER MARKERS PLC HUMAN MACHINE INTERFACES N N H (46.6 1.835) 5.4 0.213 Q 5.4 0.213 10 0.394 8 0.315 10 0.394 8 0.315 (46.6 1.835) Beam pitch Q Model No. H H Beam pitch (46.6 1.835) H 4 0.157 (46.6 1.835) N Q 5.4 0.213 ø5 ø0.197 Gray cable ø5 ø0.197 Gray cable (with black line) ø5 ø0.197 Gray cable SF4B-H12C(A-J05) SF4B-H16C(A-J05) SF4B-A8C(A-J05) SF4B-A12C(A-J05) SF4B-H28C(A-J05) SF4B-H32C(A-J05) D B SF4B-A16C(A-J05) SF4B-H40C(A-J05) SF4B-A20C(A-J05) SF4B-H48C(A-J05) SF4B-A24C(A-J05) SF4B-C SF4B-H56C(A-J05) SF4B-A28C(A-J05) SF4C SF4B-H64C(A-J05) SF4B-A32C(A-J05) SF4B-H72C(A-J05) SF4B-A36C(A-J05) SF4B-H80C(A-J05) SF4B-A40C(A-J05) SF4B-H88C(A-J05) SF4B-A44C(A-J05) SF4B-H96C(A-J05) SF4B-A48C(A-J05) SF2B B 10.6 0.417 ø5 ø0.197 Gray cable (with black line) 10 0.394 5.4 0.213 8 0.315 23.8 0.937 ø15.6 ø0.614 ø15.6 ø0.614 Control Units BSF4-AH80 L (45 1.772) (45 1.772) SF4B-H36C(A-J05) SF4B D Receiver Optical Touch Switch SF2C 120 4.724 SF4B-H24C(A-J05) Definition of Sensing Heights M 108 4.252 10.6 0.417 Emitter SF4B-H20C(A-J05) Safety Components L Q 23.8 0.937 23.8 0.937 MACHINE VISION SYSTEMS Light Curtains D 5.4 0.213 5.4 0.213 P FA COMPONENTS Selection Guide 10.8 0.425 10.8 0.425 Protective height 120 M 120 4.724 4.724 (4.2 0.165) 19.6 0.772 P P ENERGY CONSUMPTION VISUALIZATION COMPONENTS UV CURING SYSTEMS 32.2 1.268 108 4.252 MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES (4.2 0.165) (4.2 0.165) 19.6 0.772 (4.2 0.165) Model No. H Q SF4B-H□C(A-J05) 20 0.787 22.2 0.874 SF4B-A□C(A-J05) 40 1.575 42.2 1.661 279 10.984 359 14.134 439 17.283 519 20.433 599 23.583 679 26.732 759 29.882 839 33.031 999 39.331 1,159 45.630 1,319 51.929 1,479 58.228 1,639 64.528 1,799 70.827 1,959 77.126 SF4B-H□C(A-J05) SF4B-A□C(A-J05) 220 8.661 — 300 11.811 380 14.961 460 18.110 540 21.260 620 24.409 700 27.559 780 30.709 760 29.921 940 37.008 920 36.220 1,100 43.307 1,080 42.520 1,260 49.606 1,240 48.819 1,420 55.906 1,400 55.118 1,580 62.205 1,560 61.417 1,740 68.504 1,720 67.716 1,900 74.803 1,880 74.016 280 11.024 — 440 17.323 — 600 23.622 — L M 316.4 12.457 396.4 15.606 476.4 18.756 556.4 21.906 636.4 25.055 716.4 28.205 796.4 31.354 876.4 34.504 1,036.4 40.803 1,196.4 47.102 1,356.4 53.402 1,516.4 59.701 1,676.4 66.000 1,836.4 72.299 1,996.4 78.598 264.4 10.409 344.4 13.559 424.4 16.709 504.4 19.858 584.4 23.008 664.4 26.157 744.4 29.307 824.4 32.457 984.4 38.756 1,144.4 45.055 1,304.4 51.354 1,464.4 57.654 1,624.4 63.953 1,784.4 70.252 1,944.4 76.551 N P — — — — — — — — — — — — — — 399.5 15.728 479.5 18.878 559.5 22.028 419.5 16.516 472.5 18.602 525.5 20.689 578.5 22.776 631.5 24.862 — — — 858.5 33.799 965.5 38.012 1,072.5 42.224 1,179.5 46.437 1,286.5 50.650 10 0.394 23.8 0.937 Compact Light Curtain Type 4 ・ DIMENSIONS (Unit: mm in) SF4B-□CA-J05 522 SF4B-C SERIES The CAD data in the dimensions can be downloaded from our website.・ SF4B-□C Light curtain Assembly dimensions MICRO PHOTOELECTRIC SENSORS MS-SF4BC-2 AREA SENSORS MS-SF4BC-2 4.2 0.165 (4.2 0.165) 5.4 0.213 19.6 0.772 32.2 1.268 10.8 (4.2 0.165) 0.425 19.6 0.772 Protective 10.8 height 0.425 10.6 0.417 R S H Q ø5 ø0.197 Gray cable M 108 4.252 FLOW SENSORS 5.4 0.213 10.8 0.425 10.6 0.417 D U 120 4.724 INDUCTIVE PROXIMITY 5.4 0.213 SENSORS 4 0.157 T 5.4 0.213 (47.1 1.854) Beam pitch (4.2 PRESSURE 0.165) / U Q H PARTICULAR USE SENSORS 10.6SENSOR 0.417 OPTIONS WIRE-SAVING 5.4 0.213 SYSTEMS 8 0.315 23.8 14 0.551 0.937 ø5 ø0.197 Gray cable (with black line) Receiver 23.8 Emitter 0.937 R SIMPLE WIRE-SAVING UNITS S (47.1 1.854) Q 10 0.394 14 0.551 ø5 ø0.197 Gray cable (with black line) ø5 ø0.197 Gray cable 14 0.551 10 0.394 8 0.315 H (47.1 1.854) 14 0.551 23.8 0.937 D LIGHT CURTAINS / SAFETY COMPONENTS 19.6 0.772 108 4.252 Beam pitch Q 5.4 0.213 10 0.394 8 0.315 H (47.1 1.854) 5.4 0.213 10.8 0.425 Protective height (4.2 0.165) 4.2 0.165 19.6 0.772 32.2 1.268 108 4.252 T S 4.2 0.165 M 120 4.724 120 M 4.724 U D MS-SF4BC-4 108 4.252 10.6 0.417 4 0.157 T 120 M 4.724 U D MS-SF4BC-4 4 0.157 19.6 0.772 32.2 19.6 1.268 0.772 32.2 1.268 4.2 0.165 5.4 0.213 R LASER SENSORS PHOTOELECTRIC SENSORS The figure depicts space-saving mounting using the rear utility mounting bracket MS-SF4BC-2(optional) and the intermediate supporting bracket for utility mounting bracket MS-SF4BC-4(optional). 19.6 0.772 FIBER SENSORS MEASUREMENT SENSORS 10STATIC 0.394 ELECTRICITY PREVENTION 23 DEVICES 0.9 LASER MARKERS PLC (45 1.772) ø15.6 ø0.614 HUMAN MACHINE INTERFACES (45 1.772) ENERGY CONSUMPTION VISUALIZATION COMPONENTS ø15.6 ø0.614 FA COMPONENTS D Model No. SF4B-H□C(A-J05) SF4B-H12C(A-J05) SF4B-A□C(A-J05) 220 300 11.811 SF4B-H20C(A-J05) 380 14.961 SF4B-H24C(A-J05) SF4B-A12C(A-J05) 460 18.110 SF4B-H28C(A-J05) 540 21.260 SF4B-H32C(A-J05) SF4B-A16C(A-J05) 620 24.409 SF4B-H36C(A-J05) 700 27.559 SF4B-H40C(A-J05) SF4B-A20C(A-J05) 780 30.709 760 29.921 SF4B-H48C(A-J05) SF4B-A24C(A-J05) 940 37.008 920 36.220 SF4B-H56C(A-J05) SF4B-A28C(A-J05) 1,100 43.307 1,080 42.520 SF4B-H64C(A-J05) SF4B-A32C(A-J05) 1,260 49.606 1,240 48.819 SF4B-H72C(A-J05) SF4B-A36C(A-J05) 1,420 55.906 1,400 55.118 SF4B-H80C(A-J05) SF4B-A40C(A-J05) 1,580 62.205 1,560 61.417 SF4B-H88C(A-J05) SF4B-A44C(A-J05) 1,740 68.504 1,720 67.716 SF4B-H96C(A-J05) SF4B-A48C(A-J05) 1,900 74.803 1,880 74.016 SF4B-H16C(A-J05) SF4B-A8C(A-J05) Model No. H Q SF4B-H□C(A-J05) 20 0.787 22.2 0.874 SF4B-A□C(A-J05) 40 1.575 42.2 1.661 8.661 — 280 11.024 — 440 17.323 — 600 23.622 — M R 264.4 10.409 344.4 13.559 424.4 16.709 504.4 19.858 584.4 23.008 664.4 26.157 744.4 29.307 824.4 32.457 984.4 38.756 1,144.4 45.055 1,304.4 51.354 1,464.4 57.654 1,624.4 63.953 1,784.4 70.252 1,944.4 76.551 245.8 9.677 325.8 12.827 405.8 17.748 485.8 19.126 565.8 22.276 645.8 25.425 725.8 28.575 805.8 31.724 965.8 38.024 1,125.8 44.323 1,285.8 50.622 1,445.8 56.921 1,605.8 63.220 1,765.8 69.520 1,925.8 75.819 S T — — — — — — — — — — — — — — 382.9 15.075 462.9 18.224 542.9 21.374 402.9 15.862 455.9 17.949 508.9 20.035 561.9 22.122 614.9 24.209 — — — 841.9 33.146 948.9 37.358 1,055.9 41.571 1,162.9 45.783 1,269.9 49.996 U 270.4 10.646 350.4 13.795 430.4 16.945 510.4 20.094 590.4 23.244 670.4 26.394 750.4 29.543 830.4 32.693 990.4 38.992 1,150.4 45.291 1,310.4 51.590 1,470.4 57.890 1,630.4 64.189 1,790.4 70.488 1,950.4 76.787 MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Light Curtains Safety Components Optical Touch Switch Control Units Definition of Sensing Heights SF4B-C SF4C SF2C SF4B SF2B BSF4-AH80 523 Compact Light Curtain Type 4 ・ DIMENSIONS (Unit: mm in) FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS SF4B-□CA-J05 MS-SF4BC-3 (1.3 0.051) 5 0.197 B 108 4.252 5.4 0.213 P 5 0.197 D B P 27.4 1.079 N 120 D 4.724 M L 12.9 0.508 12.9 0.508 LASER MARKERS PLC HUMAN MACHINE INTERFACES 22.7 0.894 8.7 0.343 10 0.394 10 0.394 28.7 1.130 8.7 0.343 H H ø5 ø0.197 Gray cable ø5 ø0.197 Gray (with cableblack line) Emitter (45 1.772) Model No. SF4B-H12C(A-J05) SF4B-H16C(A-J05) SF4B-A8C(A-J05) SF4B-A12C(A-J05) SF4B-H28C(A-J05) SF4B-H32C(A-J05) SF4B-A16C(A-J05) SF4B-H40C(A-J05) SF4B-A20C(A-J05) SF4B-H48C(A-J05) SF4B-A24C(A-J05) SF4B-C SF4B-H56C(A-J05) SF4B-A28C(A-J05) SF4C SF4B-H64C(A-J05) SF4B-A32C(A-J05) SF4B-H72C(A-J05) SF4B-A36C(A-J05) SF4B-H80C(A-J05) SF4B-A40C(A-J05) SF4B-H88C(A-J05) SF4B-A44C(A-J05) SF4B-H96C(A-J05) SF4B-A48C(A-J05) SF2B D B Control Units BSF4-AH80 0.394 8.7 0.343 22.710 0.894 Model No. H Q SF4B-H□C(A-J05) 20 0.787 22.2 0.874 SF4B-A□C(A-J05) 40 1.575 42.2 1.661 279 10.984 359 14.134 439 17.283 519 20.433 599 23.583 679 26.732 759 29.882 839 33.031 999 39.331 1,159 45.630 1,319 51.929 1,479 58.228 1,639 64.528 1,799 70.827 1,959 77.126 SF4B-H□C(A-J05) SF4B-A□C(A-J05) 220 8.661 — 300 11.811 380 14.961 460 18.110 540 21.260 620 24.409 700 27.559 780 30.709 760 29.921 940 37.008 920 36.220 1,100 43.307 1,080 42.520 1,260 49.606 1,240 48.819 1,420 55.906 1,400 55.118 1,580 62.205 1,560 61.417 1,740 68.504 1,720 67.716 1,900 74.803 1,880 74.016 280 11.024 — 440 17.323 — 600 23.622 — L M 316.4 12.457 396.4 15.606 476.4 18.756 556.4 21.906 636.4 25.055 716.4 28.205 796.4 31.354 876.4 34.504 1,036.4 40.803 1,196.4 47.102 1,356.4 53.402 1,516.4 59.701 1,676.4 66.000 1,836.4 72.299 1,996.4 78.598 264.4 10.409 344.4 13.559 424.4 16.709 504.4 19.858 584.4 23.008 664.4 26.157 744.4 29.307 824.4 32.457 984.4 38.756 1,144.4 45.055 1,304.4 51.354 1,464.4 57.654 1,624.4 63.953 1,784.4 70.252 1,944.4 76.551 N P — — — — — — — — — — — — — — 399.5 15.728 479.5 18.878 559.5 22.028 419.5 16.516 472.5 18.602 525.5 20.689 578.5 22.776 631.5 24.862 10 0. 28.7 1.130 ø15.6 ø0.614 SF4B-H36C(A-J05) SF4B ø5 ø0.197 Gray cable 22.7 8.7 0.343 (with0.894 black line) N 5.4 0.213 Q (45 1.772) Optical Touch Switch SF2C 27.4 1.079 (47.1 1.854) N 5.4 0.213 Receiver ø15.6 ø0.614 SF4B-H24C(A-J05) Definition of Sensing Heights P 28.7 1.130 SF4B-H20C(A-J05) Safety Components 5.4 5 0.213 0.197 MACHINE VISION SYSTEMS Light Curtains 27.4 H 1.079 Q FA COMPONENTS Selection Guide 108 4.252 5.4 5 0.213 0.197 (47.1 1.854) B D Beam pitch 28.7 1.130 ENERGY CONSUMPTION VISUALIZATION COMPONENTS UV CURING SYSTEMS 2.3 0.091 L M 120 4.724 D Q (47.1 1.854) ø5 ø0.197 Gray cable 22.7 0.894 31.5 1.240 12.9 0.508 2.3 0.091 108 4.252 MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES L M 120 4.724 120 4.724 M L 12.9 Beam 0.508pitch 12.9 0.508 27.4 1.079H N (47.1 1.854) 5.4 0.213 Q 5.4 0.213 12.9 0.508 Protective height 108 4.252 5.4 0.213 34.3 1.350 31.5 1.240 Protective height MS-SF4BC-4 (1.3 19.6 0.772 34.3 1.350 34.3 1.350 2.3 0.091 MS-SF4BC-4 19.6 0.772 19.6 0.772 31.5 1.240 34.3 1.350 2.3 0.091 (1.3 0.051) (12.9 0.508) (12.9 0.508) 19.6 0.772 31.5 1.240 SENSOR OPTIONS WIRE-SAVING SYSTEMS Light curtain MS-SF4BC-3 (1.3 0.051) INDUCTIVE PROXIMITY SENSORS SIMPLE WIRE-SAVING UNITS SF4B-□C The figure depicts side mounting using the side utility mounting bracket MS-SF4BC-3(optional) and the intermediate supporting bracket for utility mounting bracket MS-SF4BC-4(optional). PRESSURE / FLOW SENSORS PARTICULAR USE SENSORS The CAD data in the dimensions can be downloaded from our website.・ Assembly dimensions AREA SENSORS LIGHT CURTAINS / SAFETY COMPONENTS SF4B-C SERIES — — — 858.5 33.799 965.5 38.012 1,072.5 42.224 1,179.5 46.437 1,286.5 50.650 Compact Light Curtain Type 4 ・ DIMENSIONS (Unit: mm in) SF4B-□CA-J05 524 SF4B-C SERIES The CAD data in the dimensions can be downloaded from our website.・ SF4B-□C Light curtain Assembly dimensions The figure depicts space-saving mounting using the side utility mounting bracket MS-SF4BC-3(optional) and the intermediate supporting bracket for utility mounting bracket MS-SF4BC-4(optional). MS-SF4BC-3 MS-SF4BC-3 27.4 1.079 (1.3 0.051) 34.3 1.350 27.4 1.079 MS-SF4BC-4 R 31.5 1.240 R 2.3 0.091 5.4 0.213 T S 10 0.394 28.7 1.130 D 10 0.394 120 4.724 120 M U 4.724 12.9 H0.508 Beam pitch 12.9 H 0.508 Q (47.1 1.854) D U M H 120 108 4.724 4.252 5.4 0.213 5 0.197 108 4.252 (47.1 1.854) H Beam pitch 22.7 0.894 ø5 ø0.197 ø5 ø0.197 Gray cable Gray cable 22.7 (with black line) 0.894 ø5 ø0.197 Gray cable 8.7 0.343 28.7 1.130 U M 108 4.252 22.7 0.894 8.7 0.343 Protective height 120 M U 4.724 108 1.240 31.5 4.252 2.3 0.091 12.9 0.508 Protective height MS-SF4BC-4 12.9 5.4 0.213 0.508 12.9 0.508 5 0.197 Q (47.1 1.854) 5.4 0.213 T 5 0.197 5.4 0.213 S D 34.3 1.350 27.4 1.079 19.6 0.772 31.5 1.24034.3 1.350 2.3 12.9 0.091 0.508 34.3 1.350 19.6 0.772 ø5 ø0.197 Gray cable (with black line) Emitter D 5.4 0.213 Q (47.1 1.854) 31.5 1.240 2.3 R 0.091 INDUCTIVE PROXIMITY SENSORS T 5.4 0.213 5 0.197 S SENSOR OPTIONS 5.4 0.213 WIRE-SAVING SYSTEMS Q 10 0.394 8.7 0.343 22.728.7 0.894 1.130 8.7 0.343 PARTICULAR USE R SENSORS T SIMPLE WIRE-SAVING UNITS S LASER MARKERS PLC HUMAN MACHINE INTERFACES ø15.6 (45ø0.614 1.772) ø15.6 ø0.614 ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS D SF4B-H□C(A-J05) SF4B-A□C(A-J05) 220 300 11.811 SF4B-H20C(A-J05) 380 14.961 SF4B-H24C(A-J05) SF4B-A12C(A-J05) 460 18.110 SF4B-H28C(A-J05) 540 21.260 SF4B-H32C(A-J05) SF4B-A16C(A-J05) 620 24.409 SF4B-H36C(A-J05) 700 27.559 SF4B-H40C(A-J05) SF4B-A20C(A-J05) 780 30.709 760 29.921 SF4B-H48C(A-J05) SF4B-A24C(A-J05) 940 37.008 920 36.220 SF4B-H56C(A-J05) SF4B-A28C(A-J05) 1,100 43.307 1,080 42.520 SF4B-H64C(A-J05) SF4B-A32C(A-J05) 1,260 49.606 1,240 48.819 SF4B-H72C(A-J05) SF4B-A36C(A-J05) 1,420 55.906 1,400 55.118 SF4B-H80C(A-J05) SF4B-A40C(A-J05) 1,580 62.205 1,560 61.417 SF4B-H88C(A-J05) SF4B-A44C(A-J05) 1,740 68.504 1,720 67.716 SF4B-H96C(A-J05) SF4B-A48C(A-J05) 1,900 74.803 1,880 74.016 SF4B-H16C(A-J05) SF4B-A8C(A-J05) Model No. H Q SF4B-H□C(A-J05) 20 0.787 22.2 0.874 SF4B-A□C(A-J05) 40 1.575 42.2 1.661 MEASUREMENT SENSORS 10 0.394 STATIC 28.7 ELECTRICITY 1.130 PREVENTION DEVICES (45 1.772) SF4B-H12C(A-J05) MICRO PHOTOELECTRIC SENSORS PRESSURE / FLOW SENSORS 27.4 1.079 Receiver Model No. PHOTOELECTRIC SENSORS LIGHT CURTAINS / SAFETY COMPONENTS (1.3 0.051) (12.9 0.508) (1.3 0.051) 19.6 0.772 19.6 0.772 LASER SENSORS AREA SENSORS (12.9 0.508) (1.3 0.051) FIBER SENSORS 8.661 — 280 11.024 — 440 17.323 — 600 23.622 — M R 264.4 10.409 344.4 13.559 424.4 16.709 504.4 19.858 584.4 23.008 664.4 26.157 744.4 29.307 824.4 32.457 984.4 38.756 1,144.4 45.055 1,304.4 51.354 1,464.4 57.654 1,624.4 63.953 1,784.4 70.252 1,944.4 76.551 245.8 9.677 325.8 12.827 405.8 17.748 485.8 19.126 565.8 22.276 645.8 25.425 725.8 28.575 805.8 31.724 965.8 38.024 1,125.8 44.323 1,285.8 50.622 1,445.8 56.921 1,605.8 63.220 1,765.8 69.520 1,925.8 75.819 S T — — — — — — — — — — — — — — 382.9 15.075 462.9 18.224 542.9 21.374 402.9 15.862 455.9 17.949 508.9 20.035 561.9 22.122 614.9 24.209 — — — 841.9 33.146 948.9 37.358 1,055.9 41.571 1,162.9 45.783 1,269.9 49.996 U 270.4 10.646 350.4 13.795 430.4 16.945 510.4 20.094 590.4 23.244 670.4 26.394 750.4 29.543 830.4 32.693 990.4 38.992 1,150.4 45.291 1,310.4 51.590 1,470.4 57.890 1,630.4 64.189 1,790.4 70.488 1,950.4 76.787 MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Light Curtains Safety Components Optical Touch Switch Control Units Definition of Sensing Heights SF4B-C SF4C SF2C SF4B SF2B BSF4-AH80 525 ・ FIBER SENSORS LASER SENSORS PHOTOELECTRIC SENSORS MICRO PHOTOELECTRIC SENSORS Compact Light Curtain Type 4 DIMENSIONS (Unit: mm in) SF4B-□CA-J05 SF4B-□C MS-SF4BC-6 MS-SF4BC-3 (24 0.945) (1.3 0.051) 27.4 1.079 68.7 2.705 PRESSURE / FLOW SENSORS 2.3 0.091 46.4 1.827 MS-SF4BC-4 5 0.197 B D V 31.5 1.240 SENSOR OPTIONS 10 0.394 SIMPLE WIRE-SAVING UNITS P MEASUREMENT SENSORS ø5 ø0.197 Gray cable 10 0.394 LASER MARKERS 108 4.252 108 4.252 12.9 0.508 12.9 0.508 (47.1 1.854) 1.854) Q (47.1 2.3 0.091 5.4 0.213 5.4 0.213 N 5.4 0.213 D P 24 0.945 WIRE-SAVING SYSTEMS 4.7 0.185 MS-SF4BC-7 27.4 1.079 N 5.4 0.213 39 1.535 Protective height Protective 120 120 height 120 4.7244.724 M L 4.724 M M 10 0.394 8.7 0.343 46.4 1.827 28.7 1.130 66.4 2.614 H 24 H H Beam pitch Model No. ø5 ø0.197 Gray cable SF4B-H12C(A-J05) SF4B-H16C(A-J05) SF4B-A8C(A-J05) SF4B-A12C(A-J05) SF4B-H28C(A-J05) SF4B-H32C(A-J05) SF4B-A16C(A-J05) Control Units SF4B-H40C(A-J05) SF4B-A20C(A-J05) SF4B-H48C(A-J05) SF4B-A24C(A-J05) SF4B-H56C(A-J05) SF4B-A28C(A-J05) SF4B SF2B BSF4-AH80 39 1.535 24.3 0.957 ø5 ø0.197 Gray cable (with black line) 46.4 1.827 12.5 0.492 66.4 2.614 26 1.024 D B SF4B-H36C(A-J05) SF2C 0.945 (47.1 1.854) H P (47.1 1.854) 5.4 0.213 N 27.4 1.079 SF4B-H64C(A-J05) SF4B-A32C(A-J05) SF4B-H72C(A-J05) SF4B-A36C(A-J05) SF4B-H80C(A-J05) SF4B-A40C(A-J05) SF4B-H88C(A-J05) SF4B-A44C(A-J05) SF4B-H96C(A-J05) SF4B-A48C(A-J05) Model No. H Q SF4B-H□C(A-J05) 20 0.787 22.2 0.874 SF4B-A□C(A-J05) 40 1.575 42.2 1.661 279 10.984 359 14.134 439 17.283 519 20.433 599 23.583 679 26.732 759 29.882 839 33.031 999 39.331 1,159 45.630 1,319 51.929 1,479 58.228 1,639 64.528 1,799 70.827 1,959 77.126 SF4B-H□C(A-J05) SF4B-A□C(A-J05) 220 8.661 — 300 11.811 380 14.961 460 18.110 540 21.260 620 24.409 700 27.559 780 30.709 760 29.921 940 37.008 920 36.220 1,100 43.307 1,080 42.520 280 11.024 — 440 17.323 — 600 23.622 — 1,260 49.606 1,240 48.819 1,420 55.906 1,400 55.118 1,580 62.205 1,560 61.417 1,740 68.504 1,720 67.716 1,900 74.803 1,880 74.016 M 22.7 0.894 8.7 0.343 10 0.394 ø5 ø0.197 Gray cable (with black line) 264.4 10.409 344.4 13.559 424.4 16.709 504.4 19.858 584.4 23.008 664.4 26.157 744.4 29.307 824.4 32.457 984.4 38.756 1,144.4 45.055 1,304.4 51.354 1,464.4 57.654 1,624.4 63.953 1,784.4 70.252 1,944.4 76.551 N P — — — — — — — — — — — — — — 399.5 15.728 479.5 18.878 559.5 22.028 419.5 16.516 472.5 18.602 525.5 20.689 578.5 22.776 631.5 24.862 — — — 858.5 33.799 965.5 38.012 1,072.5 42.224 1,179.5 46.437 1,286.5 50.650 N 5.4 0.213 Q ø15.6 ø0.614 Optical Touch Switch SF4C 5.4 0.213 Beam pitch 5.4 5 0.213 0.197 (45 1.772) SF4B-H24C(A-J05) SF4B-C 2.3 0.091 Receiver SF4B-H20C(A-J05) Definition of Sensing Heights 108 10 0.394 4.252 Q 22.7 0.894 12.5 0.492 24.3 0.957 26 1.024 BD 31.5 1.240 MACHINE VISION SYSTEMS Safety Components L M 120 4.724 V 108 4.252 FA COMPONENTS Light Curtains D Emitter ENERGY CONSUMPTION VISUALIZATION COMPONENTS Selection Guide 46.4 1.827 4.7 0.185 Q HUMAN MACHINE INTERFACES UV CURING SYSTEMS 10.8 0.425 32.2 1.268 (1.3 (12.9 0.508) 27.4 1.079 68.7 19.6 0.772 2.705 34.3 1.350 39 31.5 1.240 1.535 12.9 2.3 0.091 0.508 19.6 0.772 19.6 0.772 10.8 34.3 0.425 1.350 32.2 1.268 31.5 1.240 39 1.535 B (24 0.945) 19.6 0.772 INDUCTIVE PROXIMITY SENSORS PLC Light curtain The figure depicts side mounting using the side mounting bracket MS-SF4BC-6(optional) and the intermediate supporting bracket for side mounting bracket MS-SF4BC-7(optional). LIGHT CURTAINS / SAFETY COMPONENTS STATIC ELECTRICITY PREVENTION DEVICES The CAD data in the dimensions can be downloaded from our website.・ Assembly dimensions AREA SENSORS PARTICULAR USE SENSORS SF4B-C SERIES V 308.4 12.142 388.4 15.291 468.4 18.441 548.4 21.591 628.4 24.740 708.4 27.890 788.4 31.039 868.4 34.189 1,028.4 40.488 1,188.4 46.787 1,348.4 53.087 1,508.4 59.386 1,668.4 65.685 1,828.4 71.984 1,988.4 78.283 10 0. 28.7 1.130 Compact Light Curtain Type 4 ・ DIMENSIONS (Unit: mm in) SF4B-□CA-J05 526 SF4B-C SERIES The CAD data in the dimensions can be downloaded from our website.・ SF4B-□C Light curtain Assembly dimensions The figure depicts space-saving mounting using the side mounting bracket MS-SF4BC-6(optional) and the intermediate supporting bracket for side mounting bracket MS-SF4BC-7(optional). (24 0.945) (24 0.945) MS-SF4BC-3 (27.4 1.079) 68.7 10.8 2.705 (1.3 0.051) 0.425 39 46.4 32.2 19.6 0.772 1.535 27.4 1.079 1.827 1.268 34.3 4.7 1.350 0.185 MS-SF4BC-4 MS-SF4BC-6 R R 31.5 1.240 T MS-SF4BC-7 10 0.394 5.4 0.213 T 19.6 2.3 D 31.5 1.240 0.091 0.772 2.3 0.091 108 108 4.252 4.252 5.4 0.213 12.9 0.508 (47.1 1.854) 12.9 0.508 Q (47.1 1.854) Q 24 0.945 S 5 0.197 5.4 0.213 S 5.4 0.213 ø5 ø0.197 Gray cable (39 1.535) 10 0.394 10 0.394 Protective height Protective 120 120 height 4.724 4.724 U M M U 120 M U 4.724 H H H 34.3 1.350 4.7 0.185 12.9 0.508 D U 2.3 19.6 M 120 0.772 0.091 4.724 108 4.252 H Q 27.4 1.079 5.4 0.213 5 0.197 SENSOR OPTIONS 5.4 0.213 WIRE-SAVING SYSTEMS (39 1.535) 22.7 0.894 ø5 ø0.197 0.343 10 0.394 8.7 Gray cable 28.7 (with black line) 1.130 SF4B-H□C(A-J05) SF4B-A□C(A-J05) 220 300 11.811 SF4B-H20C(A-J05) 380 14.961 SF4B-H24C(A-J05) SF4B-A12C(A-J05) 460 18.110 SF4B-H28C(A-J05) 540 21.260 SF4B-H32C(A-J05) SF4B-A16C(A-J05) 620 24.409 SF4B-H36C(A-J05) 700 27.559 SF4B-H40C(A-J05) SF4B-A20C(A-J05) 780 30.709 760 29.921 SF4B-H48C(A-J05) SF4B-A24C(A-J05) 940 37.008 920 36.220 SF4B-H56C(A-J05) SF4B-A28C(A-J05) 1,100 43.307 1,080 42.520 SF4B-H64C(A-J05) SF4B-A32C(A-J05) 1,260 49.606 1,240 48.819 SF4B-H72C(A-J05) SF4B-A36C(A-J05) 1,420 55.906 1,400 55.118 SF4B-H80C(A-J05) SF4B-A40C(A-J05) 1,580 62.205 1,560 61.417 SF4B-H88C(A-J05) SF4B-A44C(A-J05) 1,740 68.504 1,720 67.716 SF4B-H96C(A-J05) SF4B-A48C(A-J05) 1,900 74.803 1,880 74.016 H Q 20 0.787 22.2 0.874 SF4B-A□C(A-J05) 40 1.575 42.2 1.661 10 0.394 STATIC ELECTRICITY PREVENTION DEVICES FA COMPONENTS Model No. MEASUREMENT SENSORS ENERGY CONSUMPTION VISUALIZATION COMPONENTS D SF4B-H□C(A-J05) S HUMAN MACHINE INTERFACES ø15.6 ø0.614 SF4B-A8C(A-J05) T SIMPLE WIRE-SAVING UNITS PLC (45 1.772) SF4B-H16C(A-J05) PARTICULAR USE R SENSORS LASER MARKERS SF4B-H12C(A-J05) PRESSURE / FLOW SENSORS INDUCTIVE PROXIMITY SENSORS Receiver Model No. MICRO PHOTOELECTRIC SENSORS 31.5 1.240 2.3 R0.091 Q 5.4 0.213 Emitter PHOTOELECTRIC SENSORS LIGHT CURTAINS / SAFETY COMPONENTS (1.3 0.051) S (47.1 1.854) 12.5 0.492 12.5 0.492 22.7 ø5 ø0.197 0.894 24.3 ø5 ø0.197 Gray cable 24.3 Gray cable 46.4 1.827 0.957 0.957 (with black line) 26 1.024 26 1.024 66.4 2.614 8.7 46.40.343 1.827 28.7 66.4 2.614 1.130 D 10 0.394 108 5.4 0.213 4.252 T 24 0.945 (47.1 1.854) Beam pitchpitch Beam 31.5 1.240 LASER SENSORS AREA SENSORS (12.9 0.508) (27.4 1.079) 68.7 2.705 39 1.53519.6 0.772 10.8 0.425 32.2 46.4 1.268 1.827 FIBER SENSORS 8.661 — 280 11.024 — 440 17.323 — 600 23.622 — M R 264.4 10.409 344.4 13.559 424.4 16.709 504.4 19.858 584.4 23.008 664.4 26.157 744.4 29.307 824.4 32.457 984.4 38.756 1,144.4 45.055 1,304.4 51.354 1,464.4 57.654 1,624.4 63.953 1,784.4 70.252 1,944.4 76.551 245.8 9.677 325.8 12.827 405.8 17.748 485.8 19.126 565.8 22.276 645.8 25.425 725.8 28.575 805.8 31.724 965.8 38.024 1,125.8 44.323 1,285.8 50.622 1,445.8 56.921 1,605.8 63.220 1,765.8 69.520 1,925.8 75.819 S T — — — — — — — — — — — — — — 382.9 15.075 462.9 18.224 542.9 21.374 402.9 15.862 455.9 17.949 508.9 20.035 561.9 22.122 614.9 24.209 — — — 841.9 33.146 948.9 37.358 1,055.9 41.571 1,162.9 45.783 1,269.9 49.996 U 270.4 10.646 350.4 13.795 430.4 16.945 510.4 20.094 590.4 23.244 670.4 26.394 750.4 29.543 830.4 32.693 990.4 38.992 1,150.4 45.291 1,310.4 51.590 1,470.4 57.890 1,630.4 64.189 1,790.4 70.488 1,950.4 76.787 MACHINE VISION SYSTEMS UV CURING SYSTEMS Selection Guide Light Curtains Safety Components Optical Touch Switch Control Units Definition of Sensing Heights SF4B-C SF4C SF2C SF4B SF2B BSF4-AH80 527 ・ FIBER SENSORS LASER SENSORS Compact Light Curtain Type 4 DIMENSIONS (Unit: mm in) Standard mounting bracket (optional) 9.3 0.366 5.4 17 0.669 0.213 2 0.079 2 × M3 mounting hole (for main body mounting) 45° 45° 9.3 0.366 5.4 0.213 9.3 0.366 5.4 0.213 45 R7.2 R0.283 INDUCTIVE PROXIMITY SENSORS 15.7 11.5 0.618 6.5 0.453 0.256 10.8 0.425 45 ° ° R7.2 R0.283 29.4 10 0.394 1.157 PARTICULAR USE SENSORS SIMPLE WIRE-SAVING UNITS 9.3 0.366 5.4 17 0.669 0.213 2 0.079 10.8 0.425 PRESSURE / FLOW SENSORS SENSOR OPTIONS t1.5 t 0.059 t 1.5 t 0.059 MICRO PHOTOELECTRIC SENSORS LIGHT CURTAINS / SAFETY COMPONENTS The CAD data in the dimensions can be downloaded from our website.・ MS-SF4BC-1 PHOTOELECTRIC SENSORS AREA SENSORS SF4B-C SERIES 2 × M3 mounting hole (for main body mounting) 29.4 1.157 15.7 0.618 11.5 10.7 0.421 0.453 6.5 0.256 10 0.394 10.7 0.421 5 0.197 11.8 0.465 21.6 0.850 5 0.197 11.8 0.465 21.6 0.850 Material: Stainless steel (SUS) Four brackets (two each R and L type) per set Eight M3 (length: 5 mm 0.197 in) hexagon-socket head bolts and four M5 flat washers are attached. WIRE-SAVING SYSTEMS MEASUREMENT SENSORS MS-SF4BC-2 10 0.394 STATIC ELECTRICITY PREVENTION DEVICES 8 0.315 Rear utility mounting bracket (optional) t 2 t 0.079 t 2 t 0.079 3 0.118 9.3 0.366 15 5.4 0.591 0.213 19.6 0.772 LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS 4 0.157 (6 0.236) 8 0.315 12 0.472 R7.2 R0.283 7° 7° (Note) UV CURING SYSTEMS R7.2 R0.283 10 0.394 8 0.315 7° 7° (Note) 20.4 0.803 36.4 1.433 22.7 0.894 17 0.669 2 × M3 mounting hole (for main body mounting) 11 0.433 Note: The adjustment range of the light curtain angle is up to ±7 degrees. Selection Guide Safety Components 10 0.394 4 0.157 14 0.551 23.8 0.937 4 0.157 (6 0.236) 12 0.472 11 0.433 5.5 0.217 Light Curtains 28 1.102 20.4 36.4 0.803 1.433 22.7 0.894 17 0.669 MACHINE VISION SYSTEMS 10 0.394 9.3 15 0.366 0.591 5.4 0.213 19.6 0.772 28 1.102 2 × M3 mounting hole (for main body mounting) FA COMPONENTS 8 0.315 3 0.118 MS-SF4BC-3 5.5 0.217 4 0.157 Material: Stainless steel (SUS) Four brackets (two each R and L type) per set Eight M3 (length: 6 mm 0.236 in) hexagon-socket head bolts and four M5 flat washers are attached. 14 0.551 23.8 0.937 Side utility mounting bracket (optional) t 2 t 0.079 t 2 t 0.079 Optical Touch Switch Control Units Definition of Sensing Heights 28 1.102 28 1.102 SF4B-C SF4C SF4B SF2B 32.5 1.280 32.5 1.280 SF2C R7.2 R0.283 BSF4-AH80 7° 7° (Note) 2 × M3 mounting hole (for main body mounting) 5.4 0.213 9.3 0.366 8.7 0.343 13.7 0.539 19.4 28.7 0.764 1.130 10 0.394 15 0.591 22.7 0.894 Note: The adjustment range of the light curtain angle is up to ±7 degrees. 9.3 0.366 2 × M3 mounting hole (for main body mounting) 5.4 0.213 8.7 0.343 10 0.394 7° 7° (Note) R7.2 R0.283 13.7 0.539 19.4 0.764 28.7 1.130 Material: Stainless steel (SUS) Four brackets (two each R and L type) per set Eight M3 (length: 6 mm 0.236 in) hexagon-socket head bolts and four M5 flat washers are attached. 15 0.591 22.7 0.894 Compact Light Curtain Type 4 ・ DIMENSIONS (Unit: mm in) SF4B-C SERIES The CAD data in the dimensions can be downloaded from our website.・ MS-SF4BC-4 LASER SENSORS PHOTOELECTRIC SENSORS 30 1.181 0.5 0.020 MICRO PHOTOELECTRIC SENSORS 20 0.787 5.4 0.213 AREA SENSORS 33.5 1.319 LIGHT CURTAINS / SAFETY COMPONENTS 26 1.024 18.5 0.728 5.4 0.213 26 1.024 18.5 0.728 13.5 0.531 11 0.433 13.5 0.531 11 0.433 t 1.5 t 0.059 3.6 0.142 9 0.354 PRESSURE / FLOW SENSORS 4 0.157 10.5 0.413 20.5 0.807 27.5 1.083 1 0.039 32.2 1.268 20.6 0.811 (20.2 0.795) INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS SENSOR OPTIONS 31.5 1.240 15.5 0.610 15.5 0.610 (28.5 1.122) t 1.5 t 0.059 (20.2 0.795) 28.5 1.122 38.7 1.524 34.3 1.350 22.7 0.894 11.1 5.7 0.437 0.224 34.7 1.366 11.2 0.441 5.2 0.205 t 2 t 0.079 15 0.591 7.2 0.283 t 2 t 0.079 Material: Stainless steel (SUS) Two pcs. M5 flat washers, two pcs. assembled M3 (length: 6 mm 0.236 in) hexagon-socket head bolts for rear mounting, two pcs. attachments for side mounting Note: The numbers of sets required by SF4B-H□C(A-J05)(40 or more beam axes) and SF4B-A□C(A-J05) (20 or more beam axes) are as follows: SF4B-H40C(A-J05), SF4B-H48C(A-J05), SF4B-H56C(A-J05), SF4B-A20C(A-J05), SF4B-A24C(A-J05), SF4B-A28C(A-J05): 1 set SF4B-H64C(A-J05), SF4B-H72C(A-J05), SF4B-H80C(A-J05), SF4B-H88C(A-J05), SF4B-H96C(A-J05), SF4B-A32C(A-J05), SF4B-A36C(A-J05), SF4B-A40C(A-J05), SF4B-A44C(A-J05), SF4B-A48C(A-J05): 2 sets MS-SF4BC-5 Intermediate supporting bracket for standard mounting bracket (optional) SIMPLE WIRE-SAVING UNITS WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS FA COMPONENTS MACHINE VISION SYSTEMS t 2 t 0.079 t 2 t 0.079 UV CURING SYSTEMS 24.6 0.969 33 1.299 Selection Guide 30.4 1.197 Light Curtains 22.4 0.882 22.8 0.898 14.8 0.583 9.8 0.386 FIBER SENSORS Intermediate supporting bracket for utility mounting bracket (optional) 30.6 1.205 20.6 0.811 6 0.236 38.5 1.516 528 18.7 0.736 13.7 0.539 13.4 0.528 8.7 0.343 2 × M3 mounting hole for countersunk screw Safety Components Optical Touch Switch 6 × M3 mounting hole for countersunk screw Control Units Definition of Sensing Heights 30 20 1.181 0.787 SF4B-C SF4C 5 0.197 40 1.575 20 0.787 20 0.787 60 2.362 SF2C SF4B SF2B 25 0.984 15 0.591 Material: Stainless steel (SUS) Two pcs. for rear mounting, two pcs. for side mounting Note: The numbers of sets required by SF4B-H□C(A-J05)(40 or more beam axes) and SF4B-A□C(A-J05) (20 or more beam axes) are as follows: SF4B-H40C(A-J05), SF4B-H48C(A-J05), SF4B-H56C(A-J05), SF4B-A20C(A-J05), SF4B-A24C(A-J05), SF4B-A28C(A-J05): 1 set SF4B-H64C(A-J05), SF4B-H72C(A-J05), SF4B-H80C(A-J05), SF4B-H88C(A-J05), SF4B-H96C(A-J05), SF4B-A32C(A-J05), SF4B-A36C(A-J05), SF4B-A40C(A-J05), SF4B-A44C(A-J05), SF4B-A48C(A-J05): 2 sets BSF4-AH80 529 ・ FIBER SENSORS LASER SENSORS Compact Light Curtain Type 4 SF4B-C SERIES DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from our website.・ MS-SF4BC-6 Side mounting bracket (optional) PHOTOELECTRIC SENSORS t 2 t 0.079 t 2 t 0.079 MICRO PHOTOELECTRIC SENSORS 24 0.945 24 0.945 AREA SENSORS PRESSURE / FLOW SENSORS SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS M3 mounting hole (for main body mounting) 9 0.354 20 0.787 45.4 1.787 4 0.157 46.4 1.827 66.4 2.614 R7.2 R0.283 Note 1 7° 7° 10 0.394 INDUCTIVE PROXIMITY SENSORS PARTICULAR USE SENSORS 22.3 0.878 3 (26 1.024) 22.3 0.878 (26 1.024) LIGHT CURTAINS / SAFETY COMPONENTS 20 0.78715 0.591 R7.2 R0.283 Note 1 7° M3 mounting hole (for main body mounting) 13.7 0.539 19.4 0.764 25.4 1.000 13.7 0.539 20 19.4 0.787 0.764 25.4 45.4 1.000 1.787 4 0.157 32 1.260 10 0.394 9 0.354 7° 10 0.394 46.4 1.827 20 15 0.787 0.591 32 1.260 66.4 2.614 10 0.394 WIRE-SAVING SYSTEMS MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES LASER MARKERS PLC 5.4 0.213 12.5 0.492 9.3 9.7 0.366 0.382 MS-SF4BC-7 31.5 1.240 t 1.5 t 0.059 32.2 1.268 20.6 0.811 9 0.354 20.2 0.795 t2 12.5 0.492 t 0.079 8.1 0.319 15.5 0.610 37.2 1.465 17.2 0.678 13.2 0.520 Light Curtains Safety Components Optical Touch Switch 15.5 0.610 37.5 1.476 11.5 0.453 Material: Stainless steel (SUS) Two brackets per set Two M5 flat washers and M3 (length: 6 mm 0.236 in) hexagonsocket head bolts in assembled state are attached. 10 10 0.394 0.394 15 0.591 20 0.787 SFB-CC□-MU Mating cable with connector on one end (optional) 45 (1.772 ) SF2C BSF4-AH80 20.8 0.819 4 0.158 1.8 0.071 SF4C SF2B 27.5 1.083 5.4 0.213 Definition of Sensing Heights SF4B 3.6 0.142 14.5 13.5 11 0.433 0.571 0.531 Control Units SF4B-C 9.7 9.3 0.382 0.366 (28.5 1.122) UV CURING SYSTEMS Selection Guide 5.4 0.213 12.5 0.492 Intermediate supporting bracket for side mounting bracket (optional) ENERGY CONSUMPTION VISUALIZATION COMPONENTS MACHINE VISION SYSTEMS 4 0.157 Note: The adjustment range of the light curtain angle is up to ±7 degrees. Material: Stainless steel (SUS) Four brackets (two each L and R type) per set Eight M3 (length: 6 mm 0.236 in) hexagon-socket head bolts and four M5 flat washers are attached. HUMAN MACHINE INTERFACES FA COMPONENTS 4 0.157 SFB-CCJ□-MU 45 (1.772 ) L Mating cable with connectors on both ends (optional) 45 (1.772 ) L ø15.6 ø0.614 ø15.6 ø0.614 ø6 ø0.236 ø6 ø0.236 • Length: L Model No. ø15.6 ø0.614 • Length: L Length: L Model No. SFB-CC3-MU 3,000 118.110 SFB-CCJ3D-MU SFB-CC7-MU 7,000 275.591 SFB-CCJ3E-MU SFB-CC10-MU 10,000 393.701 SFB-CCJ10D-MU SFB-CCJ10E-MU Length: L 3,000 118.110 10,000 393.701 Compact Light Curtain Type 4 ・ DIMENSIONS (Unit: mm in) SF-C13 Control unit (optional) 6.75 0.266 4 0.157 × 5 = 15 34.5 30.118 × 0.197 = 0.591 1.358 35 1.378 67.3 2.650 130 5.118 10 0.394 13.5 0.531 ・ SF-IND-2 5 0.197 6 0.236 SF4B-C SERIES The CAD data in the dimensions can be downloaded from our website.・ FIBER SENSORS ・ LASER SENSORS SFB-HC ・・ Handy-controller (optional) PHOTOELECTRIC SENSORS 65 2.559 30 1.181 25.4 1.000 23 0.906 MICRO PHOTOELECTRIC SENSORS AREA SENSORS ø6 ø0.236 cables, 0.5 m 1.640 ft long LIGHT CURTAINS / SAFETY COMPONENTS PRESSURE / FLOW SENSORS 91.6 3.606 6.5 0.256 80 3.150 13 0.512 80.8 3.181 Suitable for 35 mm 1.378 in width DIN rail ・・ INDUCTIVE PROXIMITY SENSORS 140 5.512 5 0.197 PARTICULAR USE SENSORS 22.5 0.886 SENSOR OPTIONS SIMPLE WIRE-SAVING UNITS Large display unit for light curtain (optional) WIRE-SAVING SYSTEMS 22.8 0.898 18.3 0.720 MEASUREMENT SENSORS STATIC ELECTRICITY PREVENTION DEVICES 25 0.984 35.5 1.398 40.1 23 1.579 0.906 4.6 0.181 LASER MARKERS 18 0.709 28 1.102 5.5 0.217 ø3.6 ø0.142 cable, 3 m 9.843 ft long 25.4 1.000 PLC t 1.6 t 0.063 6.6 0.260 10.4 0.409 HUMAN MACHINE INTERFACES ENERGY CONSUMPTION VISUALIZATION COMPONENTS Material: Bracket ··· Cold rolled carbon steel (SPCC)(Black chromate) Enclosure ··· POM Cover ··· Polycarbonate ・ MS-SF4BCH-□   MACHINE VISION SYSTEMS Metal protection case (optional) W W     Model No.             ' % $ & %   UV CURING SYSTEMS       FA COMPONENTS ・・     530     Material: Stainless steel (SUS304)     A B C D MS-SF4BCH-12 294.4 11.591 279 10.984 264.4 10.409 140.4 5.528 MS-SF4BCH-16 374.4 14.740 359 14.134 344.4 13.559 220.4 8.677 Selection Guide MS-SF4BCH-20 454.4 17.890 439 17.283 424.4 16.709 300.4 11.827 Light Curtains MS-SF4BCH-24 534.4 21.039 519 20.433 504.4 19.858 380.4 14.976 Safety Components MS-SF4BCH-28 614.4 24.189 599 23.583 584.4 23.008 460.4 18.126 MS-SF4BCH-32 694.4 27.339 679 26.732 664.4 26.157 540.4 21.276 MS-SF4BCH-36 774.4 30.488 759 29.882 744.4 29.307 620.4 24.425 MS-SF4BCH-40 854.4 33.638 839 33.031 824.4 32.457 700.4 27.575 MS-SF4BCH-48 1,014.4 39.937 999 39.331 984.4 38.756 860.4 33.874 MS-SF4BCH-56 1,174.4 46.236 1,159 45.630 1,144.4 45.055 1,020.4 40.173 MS-SF4BCH-64 1,334.4 52.535 1,319 51.929 1,304.4 51.354 1,180.4 46.472 MS-SF4BCH-72 1,494.4 58.835 1,479 58.228 1,464.4 57.654 1,340.4 52.772 MS-SF4BCH-80 1,654.4 65.134 1,639 64.528 1,624.4 63.953 1,500.4 59.071 MS-SF4BCH-88 1,814.4 71.433 1,799 70.827 1,784.4 70.252 1,660.4 65.370 MS-SF4BCH-96 1,974.4 77.732 1,959 77.126 1,944.4 76.551 1,820.4 71.669 Optical Touch Switch Control Units Definition of Sensing Heights SF4B-C SF4C SF2C SF4B SF2B BSF4-AH80