ERG3127A

Document No. EKS10B-04485 1/10 SPECIFICATION Customer: Receipt Item: Crystal Clock Oscillators Type: NZ2520SD Nominal Frequency: 45.1584 MHz Customer’s Spec. No.: --------- NDK Spec. No.: ERG3127A Charge: Sales NDK-TP Sherise Peng Tel. +886-2-2555-0232 e-Mail sherise@tp.ndk.com Engineer Engineering dept. 3 Y.Akasaka Tel. +81-4-2900-6634 e-Mail akasaka@ndk.com Revision Record Rev. Date Items Contents Approved Checked Drawn --- 9.Apr.2014 Issue --- A.Konda Y.Akasaka C.Sakurai NIHON DEMPA KOGYO CO., LTD. Form P-1E Document No. EKS10B-04485 2/10 1. Customer’s Spec. No. : -------------- 2. NDK Spec. No. : ERG3127A 3. Type : NZ2520SD 4. Maximum Ratings Ratings Item 1 2 Supply Voltage Storage Temperature Range min Max Units -0.6 -55 6.0 +125 V C Notes 5. Electrical Specifications (Unless otherwise noted, TA=-20 to +85 C, VCC=1.8 V, Load=15 pF) Parameters 1 2 3 4 5 6 7 8 SYM Nominal Frequency Supply Voltage Current Consumption (Operating) Current Consumption (Stand-by) Output Level Load Capacitance Operating Temperature Range Overall Frequency Tolerance 9 Output Voltage 10 Rise Time(tr), Fall Time(tf) 11 Symmetry 12 Start-up Time 13 Phase Noise (1.8 V, 25 C) fnom VCC ICC IST RL Topr f/fnom VOL VOH tr/tf SYM tsu Electrical Spec. min typ max 1.71 45.1584 1.8 1.89 4 10 C-MOS 15 -20 -50 +85 +50 0.1 0.9 6 55 4 45 Units MHz V mA A pF C ppm VCC VCC ns % ms L(f) -62 dBc/Hz L(f) -92 dBc/Hz L(f) -140 dBc/Hz Notes at 1.8 V, 25 C at 1.8 V, 25 C *1 0.1 VCC to 0.9 VCC at 1/2 VCC 1 Hz offset frequency, 10 Hz offset frequency, 1 kHz offset frequency 14 Output Wave Form Rectangular Stand-by Function #1 PAD input # 3 PAD output 15 H level (0.7 VCC to VCC) or open Operating L level (0.3 VCC max) High impedance *1 Inclusive of 25 C tolerance, temp. characteristics, and supply voltage change Tr Tf VOH 0.9VCC 1/2VCC 0.1VCC 0V VOL t T Symmetry = t/T × 100% NIHON DEMPA KOGYO CO., LTD. Form P-3E Document No. EKS10B-04485 3/10 6. Measuring circuits OS VCC A 4 3 X 1 FC 2 Cby CL V CL ; 15pF MAX including input capacity of osilloscope Cby ; Bypass capacitor (0.01uF) 7. Test data will not be submitted. 8. Application drawing 8.1 Dimension drawing EKD14B-00027 8.2 Marking drawing EKH11B-00052 8.3 Reliability assurance Item EKS30B-00060 8.4 Taping & Reel drawing EKK17B-00032 EEK17B-00015 9. Instruction Notice 9.1 Noise When the NZ2520 series are used, the 0.01 F capacitor should be connected between VCC and GND line. (Closer to the product terminal is desirable.) 9.2 Resistance to dropping The NZ2520 series is designed to be impactproof so that no damage occurs when dropped a height(75 cm) three times. However, if dropped from a desk etc., it is advisable to check their performance or contact us to check it. 9.3 Electrostatic protection The NZ2520 series employ C-MOS ICs for the active element. Please use them in static-free environments. 9.4 High temperature Normal operation cannot be guaranteed for the NZ2520 series at +125 C (for 24 hours). Be sure that the units are kept within the specified temperature range. 9.5 Cleaning Basically, the NZ2520 series are applicable for ultrasonic wave cleaning. However, in some case, during ultrasonic wave cleanings, internal design may get damage. Please check condition carefully beforehand. 9.6 Other The NZ2520 series are C-MOS applied products. And careful handling(same as with C-MOS IC) are needed to avoid electrostatic problems. Incorrect PAD connection is cause of trouble. Please make sure to connect correctly as below. #2 terminal  GND #4 terminal  VCC NIHON DEMPA KOGYO CO., LTD. Form P-3E Document No. EKS10B-04485 4/10 10. Notice 10.1 Order items are manufactured according to specification. As to conditions, which are not indicated in this specification and unpredictable such as applied condition and oscillation margin, please check them beforehand. 10.2 Unless we receive request for modification within 3 weeks from the issue date of this NDK specification sheet, we will supply products according to this specification. Also, if you’d like to modify specification of order, which has been placed with delivery request within 3 weeks from the issue data of this specification sheet, we would like to discuss with you separately. 10.3 In no event shall the company be liable for any product failure resulting from an inappropriate handling or operation of the product beyond the scope of its guarantee. 10.4 Where any change to the process condition is made due to the change(s) in the production line, inform personnel of the specifications. 10.5 Should this specification data give rise to any disputes relating to any intellectual property rights or any other rights of a third person, the company shall not indemnify anyone for any damage. Their disclosure must not be construed as the grant of a license to use any of the intellectual property rights owned by the company. 10.6 If you intend to use products listed on this specification for applications that may result in loss of life or assets (controls relating to safety, medical equipment, aeronautical equipment, space equipment, etc.), please do not fail to advise us of your intention beforehand. 10.7 In the company’s production process whatever amount of ozone depleting substances (ODS) as specified in the Montreal protocol is not used. 10.8 Information contained in this specification must not be quoted, reproduced or used for other purposes including processing either in part or in full without obtaining prior approval from the company. 10.9 The appearance color and so on have a different case by purchasing it more than 2 suppliers of the component, but characteristic and reliability are guaranteed. 11. Prohibited items Be sure to use the product under the following conditions. Otherwise, the characteristics deterioration or destruction of the product may result. (1)Reflow soldering heat resistance Peak temperature: 265 C, 10 sec Heating: 230 C or higher, 40 sec Preheating: 150 C to 180 C, 120 sec Reflow passage times: 3 times (2)Manual soldering heat resistance Pressing a soldering iron of 350 C on the terminal electrode for 3 sec. NIHON DEMPA KOGYO CO., LTD. Form P-3E Document No. EKS10B-04485 5/10 *Example For Soldering Conditions (The below graph corresponds to Pb free solder) 300 Peak 260 ? 5 degC / 10sec. Max Temperature(degC) 250 4.5degC/s Max 4.5degC/s Max 200 230degC over 30 ? 10sec. 150 150-180degC 90 ? 30 sec. 100 4.5degC/s Max 50 0 Time * Recommended footprint [mm] NIHON DEMPA KOGYO CO., LTD. Form P-3E Document No. EKS10B-04485 6/10 Terminal land connections #1 STAND-BY #2 GND #3 OUTPUT #4 VCC C Date of Revise 2.Aug.2012 Charge Y.Oishi Date Name Drawn 23.Oct.2003 M.Yamaguchi Designed Checked 27.Jun.2003 M.Yamaguchi ----- Approved 23.Oct.2003 ----H.Omata Approved Reason Change VDDVCC, PAD CONNECTIONSTerminal land connections C.Ishimaru Third Angle Projection Tolerance Scale Dimension : mm -------------Title NZ2520S Dimension of External Drawing No. EKD14B-00027 Rev. C NIHON DEMPA KOGYO CO., LTD. Form M-1 Document No. EKS10B-04485 7/10 2 1 DOT MARK #1 PIN LOCATION 4 MANUFACTURES LOGO 3 1 [FREQUENCY] Digits are five and 6TH digit will be omitted. MHz unit sign is not marked. ex, ) 28.63636MHz  28.636 [Unit sign not marked] 2 [MODEL MARK] A last digit of model is marked. [MODEL MARK] NZ2520SA  Space NZ2520SB  B NZ2520SC  C NZ2520SD  D NZ2520SEA E NZ2520SF  F NZ2520SG  G NZ2520SH  H 3 [WEEK CODE (Digit are three)] ex1,) In case of 7TH week of 2006 6 0 7 Week No. (Digit are two) Lower one digit of year ex2,) In case of 31TH week of 2006 6 3 1 4 [Trace code] Trace code consists of four digits number or letter. This code indicates production date and production line number. Date of Revise G Drawn Designed Checked Approved 17.Apr.2013 Charge Approved Reason Y.Oishi C.Ishimaru Date Name Third Angle Projection Model mark addition.(NZ2520SH) 27.Jan.2006 27.Jan.2006 27.Jan.2006 27.Jan.2006 Y.Oishi Y.Okajima C.Ishimaru H.Omata mm Title Tolerance Scale ------- ------- Drawing No. NZ2520S Marking EKH11B-00052 Rev. G NIHON DEMPA KOGYO CO., LTD. Form M-1 Document No. EKS10B-04485 8/10 Environmental Test Conditions Specification 1.Thermal Shock Test 1 cycle -40C (30 minutes)  +85C(30 minutes) 1 Number of cycle: 100 cycle. 2.High Temperature High Humidity Test Temperature  +85C, Humidity  80  85%, 1 Time  250 hours. 3.+85C Aging (Non Operating) 1 Temperature  +85C, Time  500 Hours. 4.Vibration Test MIL-STD-202F test method:204D Test condition  D 1 10  2000Hz, 1.52mmp-p, or 196m/s2 20 minutes/cycle, XYZ 3 directions 4 times. 5.Shock Test MIL-STD-202F test method  213B 1 Test condition  Half sinusoidal wave 29400m/s2, 0.3ms, 3 directions, 3 times each. 6. Drop Test (JIG attachment ) Dummy load : 200g, Height : 1.5m, Fall conditions : On concrete 1 The number of times of fall : Six directions and 1 time each are made into 1 cycle, and it is 10 cycle. 7.Soldering Test (Reflow ) More than 90% of should be covered Pre heat : 15010C, 60120sec. by solder. Main heat : 301 seconds after amounting to 215 C. Peak temperature : 240C 8.Soldering Resistance ( Reflow ) Pre heat  18010C, 120 sec min, Main heat : 225C min, 70sec max. 1 Peak temperature : 260C . Reflow time : 3 times. 1 After the test mentioned above, the electrical specifications are satisfied. Also frequency deviation before and after test should be F/F 1010-6 The electrical specifications are ICC, Tr/Tf, VOL/VOH, duty cycle, stand-by function, stand-by current consumption. Reliability assurance item: EKS30B-00060C NIHON DEMPA KOGYO CO., LTD. Form M-3 Document No. EKS10B-04485 9/10 1.75 0.1 PULL DIRECTION TOP TAPE material : polyethylene terephthalate 40.0 0.15（4×10P) 4.0 0.1 1.55 0.05 2.0 0.05 1.1 3 max 8.0 0.2 2.8 0.1 3.5 0.05 0.25 0.05 2.3 0.1 0.1 4.0 0.1 1.1 0.1 NZ2520 HOLDER TAPING material: Conductive PS DIRECTION OF UNIT 2.0 0.5 13.0 0.2 60 0 0 +1 180 -1. 5 21.0 0.8 +0. 3 9.00 LABEL 11.4 1.0 Reel material: Conductive PS EIAJ standard reel Start Begin Close End 3000pcs MAX-Product Tape C Date of Revise 5.Sep.2012 Date Drawn 7.Oct.2003 Designed Checked 7.Oct.2003 Approved 7.Oct.2003 Charge Approved Y.Oishi C.Ishimaru Name Y.Okajima Y.Okajima H.Omata Reason 3000pcs-Product Tape3000pcs MAX-Product Tape. Third Angle Projection Dimension:mm Title NZ2520 Taping and Reel Spec. Tolerance Drawing No. EKK17B-00032 Scale / Rev. C NIHON DEMPA KOGYO CO., LTD. Form M-1 Document No. EKS10B-04485 10/10 Spacer Material: Paper φ180 reel Pasteboard Material: Corrugated paper A sleeve is inserted when reels are 1 to 4. Shock pad Material:Corrugated paper 154 Sleeve Material:Corrugated paper Label 21 C Date of Revise 4 Jul. 2012 0 0 21 Charge H.Ohkubo Approved K.Oguri Date Name Drawn 26 Feb. 2010 Designed Checked 26 Feb. 2010 26 Feb. 2010 H. Ohkubo K.Oguri K.Oguri Approved 26 Feb. 2010 J. Nakamura Outer box Material: Corrugated paper Reason Addition of condition when reels are 1 to 4. Third Angle Projection Dimension:mm Title 180 dia. Reel package Tolerance --------Drawing No. EEK17B-00015 Scale --------Rev. C NIHON DEMPA KOGYO CO., LTD. Form M-1