NX2016SA-27.12MHz-EXS00A-CS06744

Document No. EXS10B-18997 1/7 SPECIFICATION Customer: MTK Receipt Item: Crystal Unit Type: NX2016SA Nominal Frequency: 27.12 MHz Customer’s Spec. No.: --- NDK Spec. No.: EXS00A-CS06744 Charge: Sales Engineer NDK-TP Lilian Chiu Tel. 1st Eng. Dept. Y. Takaki Tel. 886-2-2555-0232 81-4-2900-6631 Approved M. Kubota Checked I. Miyahara Drawn Y. Takaki Revision Record Rev. Rev. Date Items Contents Remarks --- 25. Mar. 2013 Issue --- --- NIHON DEMPA KOGYO CO., LTD. Form P-1E (2006.6.28) Document No. EXS10B-18997 2/7 1. Customer specifications number : --- 2. NDK specification number : EXS00A-CS06744 3. Type : NX2016SA 4. Electrical characteristics 4.1 Nominal frequency (Fnom) 4.2 Overtone order 4.3 Adjustment Tolerance 4.4 Frequency stability over temperature 4.5 Equivalent Resistance (RR) 4.6 Shunt Capacitance (C0) 4.7 Insulation Resistance 4.8 Maximum drive level 5. Measurement circuit 5.1 Frequency measurement ･ Measuring instrument ･ Load capacitance(CL) ･ Level of drive 5.2 Equivalent resistance measurement ･ Measuring instrument ･ Load capacitance(CL) ･ Level of drive 6. Other performances 6.1 Operating Temperature range 6.2 Storage Temperature range 6.3 Air-tightness 6.4 Aging : 27.12 MHz : Fundamental : 1010-6 Max. (+ 25C) : 3010-6 Max. (-40 to +85C) The reference temp. shall be +25 C : 60  Max. : 2.0 pF Max.(Not Grounded) : Terminal to terminal insulation resistance also terminal to cover insulation resistance must be 500M (Min.) when DC100V 15V is applied. : 100W Max. : IEC  -Network : 10pF : 10uW : IEC  -Network : Series : 10uW : - 40 to + 85 C : - 40 to + 85 C : Less than 1.110-9 Pa m3/s (Helium leak detector) : 510-6 Max. / year 7. Examination results document Since a performance is guaranteed, an examination results document does not submit. 8. Application drawing 8.1 External dimension 8.2 Taping and reel figure 8.3 Holder marking 8.4 Reliability assurance Item : EXD14B-00467 : EXK17B-00200 : EXH11B-00317 : EXS30B-00250 NIHON DEMPA KOGYO CO., LTD. Form P-3B Document No. EXS10B-18997 3/7 9. Notice 9.1 Order items are manufactured according to specification. As to conditions, which are not indicated in this specification and unpredictable such as applied condition and oscillation margin, please check them beforehand. 9.2 Unless we receive request for modification within 3 weeks from the issue date of this NDK specification sheet, we will supply products according to this specification. Also, if you’d like to modify specification of order, which has been placed with delivery request within 3 weeks from the issue data of this specification sheet, we would like to discuss with you separately. 9.3 In no event shall the company be liable for any product failure resulting from an inappropriate handling or operation of the product beyond the scope of its guarantee. 9.4 Where any change to the process condition is made due to the change(s) in the production line, inform personnel of the specifications. 9.5 Should this specification data give rise to any disputes relating to any intellectual property rights or any other rights of a third person, the company shall not indemnify anyone for any damage. Their disclosure must not be construed as the grant of a license to use any of the intellectual property rights owned by the company. 9.6 If you intend to use products listed on this specification for applications that may result in loss of life or assets (controls relating to safety, medical equipment, aeronautical equipment, space equipment, etc.), please do not fail to advise us of your intention beforehand. 9.7 In the company’s production process whatever amount of ozone depleting substances (ODS) as specified in the Montreal protocol is not used. 9.8 Information contained in this specification must not be quoted, reproduced or used for other purposes including processing either in part or in full without obtaining prior approval from the company. 9.9 Crystal units will be damaged by ultrasonic welding process due to resonance of crystal wafer itself. NDK does not recommend using ultrasonic welding. If Ultra Sonic welding used, NDK strongly recommend verifying crystal unit damage by ultrasonic weld. 9.10 The appearance color has a different case by purchasing it more than 2 suppliers of the component, but characteristic and reliability are guaranteed. 10. Prohibited items Be sure to use the product under the following conditions. Otherwise, the characteristics deterioration or destruction of the product may result. (1) Reflow soldering heat resistance Peak temperature: 265C, 10 sec Heating: 230C or higher, 40 sec Preheating: 150C to 180C, 120 sec Reflow passage times: twice (2) Manual soldering heat resistance Pressing a soldering iron of 400C on the terminal electrode for four seconds (twice). NIHON DEMPA KOGYO CO., LTD. Form P-3B 1.6±0.1 Document No. EXS10B-18997 4/7 0.45±0.05 2.0 ± 0.1 Cover (Metal) Base (Alumina Ceramics) #2 (0.55) #1 Terminal Au plating finish Ni pre-plating on metalize (0.55) C0.2 #4 (0.65) (0.65) #3 LAND PATTERN (TYPICAL) PIN CONNECTION （TOP 　 VIEW ) 0.85 #4 #3 #1 #2 1.05 0.75 COVER TERMINAL #1,#3 : XTAL #2,#4 : GND(CONNECTION WITH COVER) 1.35 A Date of Revise 15.Feb.2011 Charge H.Ouchi Approved Reason K.Ueki Index position correction. Third Angle Projection Tolerance Dimension:mm ---- Date Name Drawn 19.Oct.2009 M.Harada Designed Checked 19.Oct.2009 M.Harada --- --- NX2016SA Approved 20.Oct.2009 K.Ueki Dimension Drawing Title Drawing No. EXD14B-00467 Scale --/-Rev. A NIHON DEMPA KOGYO CO., LTD. Form M-1 Document No. EXS10B-18997 5/7 1.75 0.1 PULL DIRECTION TOP TAPE material : polyethylene terephthalate 40.0 0.15（4×10P) 4.0 0.1 B 0.25 0.05 2.25 3 max 8.0 0.2 2.0 0.05 0.1 3.5 0.05 1.55 0.05 1.85 0.1 1.05 0.05 4.0 0.1 0.65 0.1 NX2016 Crystal Unit DIRECTION OF UNIT TAPING material: Conductive PS 12600 N 09 12600 N 09 12600 N 09 2.0 0.5 13.0 0.2 60 0 +1 0 180 -1. 5 21.0 0.8 +0. 3 9.0 0 LABEL 11.4 1.0 Reel material: Conductive PS EIAJ standard reel Start Begin Close End 3000pcs-Product Tape A Date of Revise 26.Nov.2009 Date Drawn 12.Apr.2005 Designed Checked 12.Apr.2005 Approved 12.Apr.2005 ------------ Charge H.Ouchi Name K.Oguri K.Oguri --------K. Miyashita Approved K.Ueki Reason Title change Third Angle Projection Dimension:mm Title NX2016 Series Taping and Reel Spec. Tolerance Drawing No. EXK17B-00200 Scale / Rev. A NIHON DEMPA KOGYO CO., LTD. Form M-1 Document No. EXS10B-18997 6/7 Marking Frequency #3 #4 Trace code (product date and Line number) AB CD #1 #2 Month Code (See Table) Year Code (Last One Digit) Manufacture's Symbol NOTE 1. Frequency Code Marking Frequency is consist of five digits, first five digits of Nominal Frequency Example Nominal Frequency 28.636363 MHz 28.636 Frequency Code 2. Month Code Table Month Month Code 1 2 3 4 5 6 Jan. Feb. Mar. Apr. May. Jun. 1 2 3 4 5 6 7 Jul. 7 8 9 10 Aug. Sep. Oct. 8 9 X 11 12 Nov. Dec. Y Z *Marking digits are not include a decimal point and dot mark. B Date of Revise 10.July.2008 Charge Miyahara Date Name Drawn 16.Jan.2006 Designed Checked 16.Jan.2006 Approved 16.Jan.2006 I.Miyahara I.Miyahara --K.Okamoto 16.Jan.2006 Approved Reason K.Kubota Delete application period. Third Angle Projection Tolerance Dimension:mm Title Crystal Holder Marking Drawing No. EXH11B-00317 Scale / Rev. B NIHON DEMPA KOGYO CO., LTD. Form M-1 Document No. EXS10B-18997 7/7 Reliability assurance item No. Test Item Test Methods (page: 1/1) Spec. Code 1 High Temperature +85±3C 720h Storage A 2 Low Temperature -40±3C 500h Storage A 3 Temperature Humidity A 4 Temperature Cycling 5 Vibration 6 Shock 7 Drop 8 Solderability 9 Reflow resistance Specification code A B +85±3C 80~85%RH 500h -40±3C / +85±3C It is 1000 cycles using 30 minutes each as 1 cycle. Frequency Range : 10~2000Hz Amplitude or Acceleration : 1.52mm or 196m/s2 1 cycle : 20 minutes Test time : Three mutually perpendicular axes each 4 hours. Devices are shocked to half sine wave (29418m/s2, 0.3msec) six mutually perpendicular axis each 1 times. Preparation : Test pieces should be fixed on the dummy load with 200g weight. Condition : Height 1.5m onto concrete Drop times : 10 times in 6 mutually perpendicular axes Pre-heat temperature : +150±10C Pre-heat time : 60~120s When the temperature of the specimen is reached at +215±3C, it shall be left for 30±1sec. Peak temperature 240±5C Material: Pb-free (Sn-3.0Ag-0.5Cu) Flux : Rosin resin methyl alcohol solvent ( 1 : 4 ) Pre-heat temperature : +150~180C Pre-heat time : 90±30s Heat temperature : more than +230C Heat time : 30s ±10s Peak temperature : +260±5C Peak time : less than 10s A A A A B A Specification f/f   3 ppm CI/CI   15 % or 5  make use larger value The electrodes should be covered by a new solder at least 90% of immersed area. Reliability assurance item: EXS30B-00250J NIHON DEMPA KOGYO CO., LTD. Form M-3