84PW021

INVERTER 84PW021 DATA SHEET DOD-PD-0743 (2nd edition) This DATA SHEET fromDOD-PD-0364(1). is updated document All information is subject to change without notice. Please confirm the sales representative before starting to design your system. Document Number: DOD-PD-0743 (2nd edition) Published date: December 2004 CP(N) 1 © NEC LCD Technologies, Ltd. 2004 All rights reserved. 84PW021 INTRODUCTION No part of this document shall be copied in any form or by any means without the prior written consent of NEC LCD Technologies, Ltd. (hereinafter called "NEC"). NEC does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a product described herein or any other liability arising from use of such application. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC or of others. While NEC has been making continuous effort to enhance the reliability of its products, the possibility of failures cannot be eliminated entirely. To minimize risks of damage to property or injury to person arising from a failure in an NEC product, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment and anti-failure features. NEC products are classified into the following three quality grades: "Standard", "Special", "Specific" The "Specific" quality grade applies only to applications developed based on a customer designated "quality assurance program" for a specific application. The recommended applications of a product depend on its quality grade, as indicated below. Customers must check the quality grade of each application before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Military systems, aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems (medical equipment, etc.) and any other equipment The quality grade of this product is "Standard" unless otherwise specified in this document. If customers intend to use this product for applications other than those specified for "Standard" quality grade, they should contact NEC sales representative in advance. DATA SHEET DOD-PD-0743 (2nd edition) 2 84PW021 CONTENTS INTRODUCTION ..........................................................................................................................................2 1. OUTLINE....................................................................................................................................................4 2. SPECIFICATION .......................................................................................................................................4 2.1 GENERAL SPECIFICATIONS..............................................................................................................4 2.2 ABSOLUTE MAXIMUM RATINGS ....................................................................................................4 2.3 ELECTRICAL CHARACTERISTICS...................................................................................................5 2.4 FUSE.......................................................................................................................................................5 2.5 POWER SUPPLY VOLTAGE SEQUENCE ..........................................................................................6 2.6 CONNECTIONS AND FUNCTIONS FOR INTERFACE PINS...........................................................7 2.7 LUMINANCE CONTROL.....................................................................................................................8 3. RELIABILITY TEST.................................................................................................................................8 4. PRECAUTIONS .........................................................................................................................................9 4.1 MEANING OF CAUTION SIGNS ........................................................................................................9 4.2 CAUTIONS ............................................................................................................................................9 4.3 ATTENTIONS ........................................................................................................................................9 4.3.1 Handling of the product .................................................................................................................9 4.3.2 Environment.................................................................................................................................10 4.3.3 Other ............................................................................................................................................10 5. OUTLINE DRAWINGS ........................................................................................................................... 11 DATA SHEET DOD-PD-0743 (2nd edition) 3 84PW021 1. OUTLINE This 84PW021 inverter is for LCD module. Adaptable LCD module is as follows. Adaptable LCD module NL10276BC16-01 2. SPECIFICATION 2.1 GENERAL SPECIFICATIONS Item Specification Unit Size See "5.OUTLINE DRAWINGS". mm Weight 49 (max.) g Delivery unit 10 (min.) set 2.2 ABSOLUTE MAXIMUM RATINGS Parameter Symbol Rating Unit Remarks Power supply voltage VDDB 0 to +14.0 V Ta = 25°C BRTC signal VBC 0 to +14.0 V BRTI signal VBI 0 to +5.3 V Storage temperature Tst -30 to +85 °C - Operating temperature Top -20 to +70 °C - ≤ 95 % Ta ≤ 40°C ≤ 85 % 40 < Ta ≤ 50°C ≤ 70 % 50 < Ta ≤ 55°C ≤ 73 Note2 g/m3 Input voltage Relative humidity Note1 Absolute humidity Note1 RH AH Ta = 25°C VDDB = 12.0V Ta > 55°C Note1: No condensation Note2: Water amount at Ta=55°C and RH=70% DATA SHEET DOD-PD-0743 (2nd edition) 4 84PW021 2.3 ELECTRICAL CHARACTERISTICS (Ta = 25°C) Parameter Symbol min. typ. max. Unit Remarks Power supply voltage VDDB 10.8 12.0 13.2 V Note1, Note2 Power supply current IDDB 790 880 970 mΑ VDDB = 12.0V (At luminance control is maximum.) Note2 High VBCH 2.0 - VDDB V Low VBCL 0 - 0.8 V VBI 0 - 2.5 V High IBCH - - 1.5 mA Low IBCL -1.5 - - mA BRTI signal IBI -1.0 - - mA Open lamp voltage VO 950 - - Vrms Note3 Lamp voltage (at steady state) VBLH - 440 - Vrms - High VAMH - 5.3 - V at malfunction Low VAML - 0 - V at normal IBL 4.5 5.0 5.5 mArms - IAMH - - 1.0 mA - Oscillation frequency FO 49 54 59 kHz - Luminance control frequency FB 245 270 295 Hz - BRTC signal Input voltage BRTI signal - BRTC signal Input current - Output voltage AM signal Output current Lamp current (per lamp) AM signal High Note1: When designing of the power supply, take the measures for the prevention of surge voltage. Note2: The power supply lines (VDDB and GNDB) occurs large ripple voltage while luminance control of LCD lamps. There is the possibility that the ripple voltage produces acoustic noise and signal wave noise in audio circuit and so on. Put a capacitor (5,000 to 6,000µF) between the power source lines (VDDB and GNDB) to reduce the noise, if the noise occurred in the circuit. Note3: Measured value with high voltage probe of a load capacitance of 3pF It is guaranteed that the adaptable LCD module can be turned on at Ta= 0 °C. 2.4 FUSE Parameter Fuse Type Supplier 11CT2A S.O.C. Corporation Rating Fusing current Remarks 4.0A Note1 2.0 A VDDB 72 V Note1: The power supply capacity should be more than the fusing current. If the power capacity is less than the fusing current, the fuse may not blow for a short time, and then nasty smell, smoking and so on may occur. DATA SHEET DOD-PD-0743 (2nd edition) 5 84PW021 2.5 POWER SUPPLY VOLTAGE SEQUENCE 10.8V 10.8V VDDB 0V 800ms max. 0s min. 0s min. BRTC 0V DATA SHEET DOD-PD-0743 (2nd edition) 6 84PW021 2.6 CONNECTIONS AND FUNCTIONS FOR INTERFACE PINS CN1 socket (Inverter side): Adaptable plug: Pin No. Symbol Function 1 VDDB Power supply 2 VDDB Power supply 3 GNDB Ground 4 GNDB Ground 5 BRTC 6 BRTI 7 BRTH 8 ☆ 53261-1171 (MOLEX Inc.) 51021-1100 (MOLEX Inc.) Backlight ON/OFF signal Remarks Note1 High or Open: Backlight ON Low: Backlight OFF This pin is pulled-up to VDDB in the product. Pull-up resistance: 3.3 kΩ Luminance control terminal Note2 AM Alert signal output at malfunction Note3 9 RSVD - 10 RSVD - 11 RSVD - Keep this pin Open. Note1: All GNDB and VDDB terminals should be used without any non-connected lines. Note2: See "2.7 LUMINANCE CONTROL". Note3: If anyone of terminals Pin No. 1, 2 or 4 (CN2 and CN3) opens, then the alert signal (+5.0V) is output. ☆ CN2 socket (Inverter side): Adaptable plug (Backlight side): ☆ SM03 (7-D1) B-BHS-1-TB(LF)(SN) (J.S.T. Mfg Co., Ltd.) BHR-04VS-1 (J.S.T. Mfg Co., Ltd.) Pin No. Symbol Signal Remarks 1 VBLH High voltage (Hot) - 2 VBLH High voltage (Hot) - 3 N. C. - Keep this pin Open. 4 VBLC Low voltage (Cold) - Note1: VBLH and VBLC must be connected correctly. If customer connects wrongly, customer will be hurt and the module will be broken. ☆ CN3 socket (Inverter side): Adaptable plug (Backlight side): ☆ SM03 (7-D1) B-BHS-1-TB(LF)(SN) (J.S.T. Mfg Co., Ltd.) BHR-04VS-1 (J.S.T. Mfg Co., Ltd.) Pin No. Symbol Signal Remarks 1 VBLH High voltage (Hot) - 2 VBLH High voltage (Hot) - 3 N. C. - Keep this pin Open. 4 VBLC Low voltage (Cold) ☆ Note1: VBLH and VBLC must be connected correctly. If customer connects wrongly, customer will be hurt and the module will be broken. DATA SHEET DOD-PD-0743 (2nd edition) 7 84PW021 2.7 LUMINANCE CONTROL Method Adjustment and luminance ratio • Adjustment The variable resistor (R) for luminance control should be 10kΩ ±5%, B curve, 1/10W. Minimum point of the resistor is the minimum luminance. Also maximum point of the resistor is the maximum luminance. The resistor (R) must be connected between BRTH-BRTI terminals. Resistor control BRTH R BRTI • Luminance ratio Note1 Resistance Luminance ratio 0Ω 20 % (Minimum) 10 kΩ 100 % (Maximum) • Adjustment Voltage control method works, when BRTH terminal is 0V and VBI voltage is input between BRTI-BRTH terminals. This control method can carry out continuation adjustment of luminance. Luminance is maximum when BRTI terminal is Open. Voltage control • Luminance ratio Note1 BRTI signal (VBI) Luminance ratio 0V 20 % (Minimum) 2.5 V 100 % (Maximum) Note1: These data are the target values. 3. RELIABILITY TEST This test is in accordance with the adaptable LCD module. Refer to Reliability Test of the adaptable LCD module. DATA SHEET DOD-PD-0743 (2nd edition) 8 84PW021 4. PRECAUTIONS 4.1 MEANING OF CAUTION SIGNS The following caution signs have very important meaning. Be sure to read "4.2 CAUTIONS" and "4.3 ATTENTIONS", after understanding these contents! ! This sign has the meaning that customer will be injured by himself or the product will sustain a damage, if customer has wrong operations. This sign has the meaning that customer will get an electrical shock, if customer has wrong operations. This sign has the meaning that customer will be injured by himself, if customer has wrong operations. 4.2 CAUTIONS ∗ Do not touch the inverter while the inverter is working, because there is a danger that customer will get an electric shock. ∗ Do not remove the inverter protection sheet, because there is a danger that customer will get an electrical shock. ∗ Be sure to wait some time after turning power OFF before starting replacement work, because the inverter is charged at a high voltage after working. ∗ Be sure to wait some time after turning power OFF before starting replacement work, because the inverter is hot after working. ∗ Do not shock the inverter, because there is a danger of breaking. 4.3 ATTENTIONS ! 4.3.1 Handling of the product ① Take hold of both ends without touch the mounting parts when customer pulls out products from packing box. If customer touches it, products may be broken down or out of adjustment, because of stress to mounting parts. ② Take the measures of electrostatic discharge such as earth band, ionic shower and so on, when customer handles the product, because products may be damaged by electrostatic. ③ Do not push-pull the interface connectors while the product is working, because wrong power sequence may break down the product. ④ Do not hook cables nor pull connection cables such as lamp cable and so on, for fear of damage. ⑤ Properly connect the adaptable plug (backlight side) to socket (inverter side) without incomplete connection. After connecting, be careful not to hook the lamp cables because incomplete connection may occur by hooking the lamp cables. This incomplete connection may cause abnormal operation of high voltage circuit. DATA SHEET DOD-PD-0743 (2nd edition) 9 84PW021 4.3.2 Environment ① Do not operate or store in high temperature, high humidity, dewdrop atmosphere or corrosive gases. Keep the product in antistatic pouch in room temperature, because of avoidance for dusts and sunlight, if customer stores the product. ② In order to prevent dew condensation occurring by temperature difference, the product packing box should be opened after leave under the environment of an unpacking room temperature enough. Because a situation of dew condensation occurring is changed by the environmental temperature and humidity, evaluate the leaving time sufficiently. (Recommendation leaving time: 6 hour or more with packing state) ③ Do not operate in high magnetic field. Product may be broken down by it. ④ This product is not designed as radiation hardened. 4.3.3 Other ① All GNDB and VDDB terminals should be used without any non-connected lines. ② Do not disassemble a product without permission of NEC. ③ Pack the product with original shipping package, because of avoidance of some damages during transportation, when customer returns it to NEC for repair and so on. DATA SHEET DOD-PD-0743 (2nd edition) 10 84PW021 5. OUTLINE DRAWINGS (Unit: mm) ☆ ☆ Note1: The values in parentheses are for reference. DATA SHEET DOD-PD-0743 (2nd edition) 11