PS7122AL-2B

6, 8 PIN DIP 250 V BREAK DOWN VOLTAGE PS7122A-1B, -2B NORMALLY CLOSED TYPE PS7122AL-1B, -2B 1-CH, 2-CH OPTICAL COUPLED MOSFET FEATURES • 1 CHANNEL TYPE: 1b Output • 2 CHANNEL TYPE: 1b + 1b Output • DESIGNED FOR AC/DC SWITCHING LINE CHANGER • SMALL AND THIN PACKAGE: 6, 8 PIN DIP • LOW LED OPERATING CURRENT: IF = 2 mA • LOW OFFSET VOLTAGE • SURFACE MOUNT AVAILABLE DESCRIPTION PS7122A-1B, -2B and PS7122AL-1B, -2B are solid state relays containing a GaAs LED on the light emitting side (input side) and normally close (N.C.) contact MOSFETs on the output side. They are suitable for analog signal control because of their low offset and high linearity. APPLICATIONS • EXCHANGE EQUIPMENT • MEASUREMENT EQUIPMENT • FA/OA EQUIPMENT ELECTRICAL CHARACTERISTICS (TA = 25°C) PART NUMBER SYMBOLS MOSFET Diode PS7122A-1B, -2B, PS7122AL-1B, -2B UNITS V µA µA pF/ch Ω ms ms Ω pF/ch 109 1.1 0.03 340 4.5 0.04 0.5 8.0 0.2 1.5 MIN TYP 1.2 MAX 1.4 5.0 1.0 PARAMETERS Forward Voltage, IF = 10 mA Reverse Current, VR = 5 V Off-State Leakage Current, IF = 10 mA, VD = 250 V Output Capacitance, IF = 10 mA,, V = 0 V, f = 1 MHz On-State Resistance, Turn-On Time1 Turn-Off Time1 IF = 0 mA, IL = 10 mA IF = 0 mA, IL = 200 mA, t≤10 ms IF = 10 mA, VL = 5 V, RL = 500 Ω, PW ≥ 10 ms VF IR ILoff COUT Ron1 Ron2 ton toff Rl-O Cl-O Coupled Isolation Resistance, Vin-out = 1.0 kVDC Isolation Capacitance, V = 0 V, f = 1 MHz Note: 1. Turn-On, Turn-Off Time. IF Pulse Input VL Input 50% 0 PS7122A-1B PS7122AL-1B 6 5 4 8 PS7122A-2B PS7122AL-2B 7 6 5 Input Monitor Rin RL VO Monitor VO = 5 V Output 90% 10% toff ton 1 2 3 1 2 3 4 California Eastern Laboratories PS7122A-1B, -2B, PS7122AL-1B, -2B ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C) SYMBOLS PARAMETERS Notes: RATINGS 1. Operation in excess of any one of these parameters may result PS7122A-1B PS7122A-2B in permanent damage. PS7122AL-1B PS7122AL-2B 2. PW = 100 µs, Duty Cycle = 1 % 3. Conditions: IF≥2 mA. The following types of load connections are available: V 5 mA 50 6 1 mW/ch 50 Connection A 2 VL (AC/DC) 5 IL A 1 3 L 4 UNITS V mA 350 500 250 200 — — Connection C Connection B 1 2 3 1 2 3 1 2 3 6 5 4 6 5 4 6 5 4 IL IL L L IL + IL IL + _ VL (DC) IL L + _ VL (DC) Diode VR IF PD IF (Peak) MOSFET VL IL Reverse Voltage Forward Current (DC) Power Dissipation Peak Forward Current2 Break Down Voltage Continuous Load Current3 Connection A Connection B Connection C Pulse Load AC/DC Connection Power Dissipation Isolation Voltage5 Total Power Dissipation Storage Temperature Operating Ambient Temp. Current4 ILP PD Coupled BV PT TSTG TA + _ VL (DC) mW/ch Vr.m.s. mW °C °C 560 1500 610 -40 to +100 -40 to +80 375 1500 850 -40 to +100 -40 to +80 4. PW = 100 ms, 1 shot. 5. AC voltage for 1 minute at TA = 25 °C, RH = 60 % between input and output. ORDERING INFORMATION RECOMMENDED OPERATING CONDITIONS (TA = 25 °C) SYMBOL IF VF PARAMETER LED Operating Current LED Off Voltage UNITS MIN TYP MAX mA V 2 0 10 20 0.5 PART NUMBER PS7122A-1B PS7122AL-1B PS7122AL-1B-E3 PS7122AL-1B-E4 PS7122A-2B PS7122AL-2B PS7122AL-2B-E3 Embossed tape 1000 pcs/reel PS7122AL-2B-E4 8-pin DIP Magazine case 50 pcs Embossed tape 1000 pcs/reel PACKAGE 6-pin DIP PACKING STYLE Magazine case 50 pcs OUTLINE DIMENSIONS (Units in mm) PS7122A-1B, -2B, PS7122AL-1B, -2B OUTLINE DIMENSIONS (Units in mm) PS7122A-1B 9.25±0.5 6 5 PS7122AL-1B (TOP VIEW) 4 (TOP VIEW) 9.25±0.5 6 5 4 1. LED Anode 2. LED Cathode 3. NC 1 2 3 4. MOSFET Drain 5. MOSFET Source 6. MOSFET Drain +0.10 -0.05 1 2 3 1. LED Anode 2. LED Cathode 3. NC 4. MOSFET Drain 5. MOSFET Source 6. MOSFET Drain 3.5±0.3 1.34±0.1 0.25 M 6.5±0.5 0.10 2.54 0.9±0.25 9.60±0.4 4.15±0.3 7.62 6.5±0.5 3.5±0.3 3.3±0.3 1.34 ± 0.1 0.25 M 2.54 0.50 ± 0.1 0 to 15 ˚ PS7122A-2B 9.25±0.5 PS7522AL-2B (TOP VIEW) 9.25±0.5 5 8 (TOP VIEW) 7 6 5 8 7 6 1 2 3 4 1 2 3 4 6.5±0.5 7.62 6.5±0.5 4.15±0.3 3.5±0.3 3.5±0.3 2.54 0.9±0.25 9.60±0.4 1. LED Anode 0.10 -0.05 +0.10 1.34±0.1 3.3±0.3 1.34 ± 0.10 2.54 0.25 M 0.50 ± 0.10 1. LED Anode 2. LED Cathode 3. LED Anode 4. LED Cathode 5. MOSFET 6. MOSFET 7. MOSFET 8. MOSFET 2. LED Cathode 0 to 15 ˚ 5. MOSFET 6. MOSFET 7. MOSFET 8. MOSFET 3. LED Anode 4. LED Cathode TYPICAL PERFORMANCE CURVES (TA = 25 °C) MAXIMUM FORWARD CURRENT vs. AMBIENT TEMPERATURE 100 300 MAXIMUM LOAD CURRENT vs. AMBIENT TEMPERATURE Maximum Forward Current, IF (mA) Maximum Load Current, IL (mA) 80 250 200 60 150 40 100 20 50 0 -25 0 25 50 75 80 100 0 -25 0 25 50 75 80 100 Ambient Temperature, TA (°C) Ambient Temperature, TA (°C) PS7122A-1B, -2B, PS7122AL-1B, -2B TYPICAL PERFORMANCE CURVES (TA = 25 °C) FORWARD VOLTAGE vs. AMBIENT TEMPERATURE 1.6 400 f = 1 MHz OUTPUT CAPACITANCE vs. SUPPLY VOLTAGE 1.4 IF = 50 mA 1.2 30 mA 20 mA 10 mA 5 mA 1.0 1 mA Output Capacitance, COUT (pF) Forward Voltage, VF (V) 300 200 100 0.8 -25 0 25 50 75 100 0 20 40 60 80 100 120 Ambient Temperature, TA (°C) NORMALIZED ON-STATE RESISTANCE vs. AMBIENT TEMPERATURE 3.0 Supply Voltage, VCC (V) ON-STATE RESISTANCE DISTRIBUTION 30 n = 50 pcs IF = 0 m A IL = 10 mA Normalized On-State Resistance, Ron 2.5 Normalized to 1.0 at TA = 25 °C IF = 0 m A IL = 10 mA 25 1.5 Number (pcs) 0 25 50 75 100 2.0 20 15 1.0 10 0.5 5 0.0 -25 0 4.3 4.4 4.5 4.6 4.7 Ambient Temperature, TA (°C) OFF-STATE LEAKAGE CURRENT vs. SUPPLY VOLTAGE 10-5 On-State Resistance, Ron (Ω) LOAD CURRENT vs. LOAD VOLTAGE 200 Off-State Leakage Current, ILoff (A) IF = 10 mA TA = 80°C Load Current, IL (mA) 10-6 100 10-7 -2.0 -1.0 0 1.0 2.0 25°C 10 -8 -100 -200 10-9 0 50 100 150 200 250 Supply Voltage, VCC (V) Load Voltage, VL (V) PS7122A-1B, -2B, PS7122AL-1B, -2B TYPICAL PERFORMANCE CURVES (TA = 25 °C) TURN-ON TIME vs. FORWARD CURRENT 0.6 VL = 5V, RL = 500 kΩ 0.5 TURN-ON TIME DISTRIBUTION 30 n = 50 pcs IF = 10 mA VL = 5 V RL = 500 Ω 25 Turn-On Time, tON (ms) Number (pcs) 5 10 15 20 25 30 0.4 20 0.3 15 0.2 10 0.1 5 0 0 0.03 0.04 0.05 0.06 Forward Current, IF (mA) Turn-On Time, tON (ms) OFF-STATE LEAKAGE CURRENT vs. SUPPLY VOLTAGE 10-7 TURN-OFF TIME DISTRIBUTION 30 Off-State Leakage Current, ILOFF (A) 25 n = 50 pcs IF = 10 mA VL = 5 V RL = 500 Ω IF = 10 mA TA = 80°C 10 -8 Number (pcs) 20 15 10-9 25°C 10 10 -10 5 0 0.3 0.4 0.5 10 -11 0 50 100 150 200 250 Turn-Off Time, tOFF (ms) LOAD CURRENT vs. LOAD VOLTAGE 12 Supply Voltage, VCC (V) TURN-OFF TIME vs. FORWARD CURRENT VL = 5 V, RL = 500 Ω 10 200 Load Current, IC (mA) 100 Turn-Off Time, tOFF (ms) 8 6 -2.0 -1.0 0 1.0 2.0 4 -100 2 -200 0 5 10 15 20 25 30 Load Voltage, VL (V) Forward Current, IF (mA) PS7122A-1B, -2B, PS7122AL-1B, -2B TYPICAL PERFORMANCE CURVES (TA = 25 °C) NORMALIZED TURN-ON TIME vs. AMBIENT TEMPERATURE 3.0 Normalized to 1.0 at TA = 25 °C IF = 10 mA VL = 5 V RL = 500 Ω 3.0 NORMALIZED TURN-OFF TIME vs. AMBIENT TEMPERATURE Normalized Turn-Off Time, TOFF Normalized Turn-On Time, TON 2.5 2.5 2.0 Normalized to 1.0 at TA = 25 °C IF = 10 mA VL = 5 V RL = 500 Ω 2.0 1.5 1.5 1.0 1.0 0.5 0.5 0.0 -25 0 25 50 75 100 0.0 -25 0 25 50 Ambient Temperature, TA75 C) (° 100 Ambient Temperature, TA (°C) TAPING SPECIFICATIONS (Units in mm) OUTLINE AND DIMENSIONS (TAPE) 1.75 ± 0.1 OUTLINE AND DIMENSIONS (REEL) 2.0 ± 0.1 4.0 ± 0.1 1.55 ± 0.1 4.3 ± 0.2 1.5 2.0 ± 0.5 7.5 ± 0.1 16.0 ± 0.3 φ13.0 ± 0.5 10.3 ± 0.1 R 1.0 0.3 1.55 ± 0.1 10.4 ± 0.1 φ21.0 ± 0.8 12.0 ± 0.1 16.4- 0.0 +2.0 Notes: 1. Packing : 1000 pcs/reel TAPING DIRECTION PS7122AL-1B-E3 PS7122AL-2B-E3 PS7122AL-1B-E4 PS7122AL-2B-E4 φ80.0 ± 5.0 φ330 PS7122A-1B, -2B, PS7122AL-1B, -2B RECOMMENDED SOLDERING CONDITIONS (1) Infrared reflow soldering • Peak reflow temperature • Time of temperature higher than 210 °C • Number of reflows • Flux 235 °C or below (package surface temperature) 30 seconds or less Two Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt % is recommended.) Recommended Temperature Profile of Infrared Reflow Package Surface Temperature T (˚C) (heating) to 10 s 235 ˚C (peak temperature) 210 ˚C to 30 s 100 to 160 ˚C 60 to 120 s (preheating) Time (s) (2) Dip soldering • Temperature • Time • Number of times • Flux 260 °C or below (molten solder temperature) 10 seconds or less One Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt % is recommended.) (3) Cautions • Fluxes Avoid removing the residual flux with freon-based cleaning solvent. EXCLUSIVE NORTH AMERICAN AGENT FOR RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS CALIFORNIA EASTERN LABORATORIES • Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054-1817 • (408) 988-3500 • Telex 34-6393 • FAX (408) 988-0279 24-Hour Fax-On-Demand: 800-390-3232 (U.S. and Canada only) • Internet: http://WWW.CEL.COM 07/17/2001 DATA SUBJECT TO CHANGE WITHOUT NOTICE