PS7200A-1A-F3

4 PIN SOP 3.0 pF LOW OUTPUT CAPACITANCE 1-CH OPTICAL COUPLED MOSFET FEATURES • LOW C X R: C X R = 30 pF • Ω • LOW OUTPUT CAPACITANCE: COUT = 3.0 pF TYP • LOW OFF-STATE LEAKAGE CURRENT: ILOFF = 0.1 nA TYP • HIGH SPEED TURN-ON TIME: tON = 0.01 ms TYP • 1 CHANNEL TYPE: (1a output) • DESIGNED FOR AC/DC SWITCHING LINE CHANGER • SMALL PACKAGE: 4 pin SOP • HIGH ISOLATION VOLTAGE: (BV = 1500 Vr.m.s.) • LOW OFFSET VOLTAGE • LOW LED OPERATING CURRENT: I F = 2 mA • SURFACE MOUNT AVAILABLE PS7200A-1A DESCRIPTION PS7200A-1A is a low output capacitance solid state relay containing a GaAs LED on the light emitting side (input side) and MOS FETs on the output side. It is suitable for high-frequency signal control, due to its low C x R, low output capacitance, and low off-state leakage current. APPLICATIONS • MEASUREMENT EQUIPMENT ELECTRICAL CHARACTERISTICS (TA = 25 °C) PART NUMBER SYMBOLS PARAMETERS Forward Voltage, IF = 10 mA Reverse Current, VR = 5 V Off-State Leakage Current, VD = 40 V Output Capacitance, V = 0 V, f = 1 MHz LED On-state Current, IL = 100 mA On-State Resistance Turn-on Time1 Turn-off Time1 IF = 10 mA, IL = 10 mA IF = 10 mA, IL = 100 mA, t≤10 ms UNITS V µA nA pF mA Ω ms ms Ω pF/ch 10 9 PS7200A-1A MIN TYP 1.2 0.1 3.0 2.0 9.3 0.01 0.07 12 0.5 0.2 MAX 1.4 5.0 100 MOS Diode FET VF IR ILOFF COUT IFon RON1 RON2 tON tOFF RI-O CI-O Coupled IF = 10 mA, VO = 5 V, PW ≥ 10 ms Isolation Resistance, VI-O = 1.0 kVDC Isolation Capacitance, V = 0 V, f = 1 MHz 0.5 Note: 1. Test Circuit for Switching Time: IF Pulse Input VL Input 50% 0 PS7200A-1A 4 3 Input Monitor Rin RL VO Monitor VO = 5 V Output 90% 1 10% ton toff 2 California Eastern Laboratories PS7200A-1A ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C) SYMBOLS Diode IF VR PD IFP MOSFET VL IL ILP PD Coupled BV PT TOP TSTG PARAMETERS Forward Current (DC) Reverse Voltage Power Dissipation Peak Foward Current2 Break Down Voltage Continuous Load Current Pulse Load Current3 AC/DC Connection Power Dissipation Isolation Voltage4 Total Power Dissipation Operating Ambient Temp. Storage Temperature UNITS mA V mW/ch A V mA mA mW/ch Vr.m.s. mW °C °C RATINGS 50 5.0 50 1 40 100 200 100 1500 150 -40 to +80 -40 to +100 RECOMMENDED OPERATING CONDITIONS (TA = 25°C) PART NUMBER SYMBOLS PARAMETERS IF LED Operating Current VF LED Off Voltage PS7200A-1A UNITS mA V MIN TYP MAX 2 10 20 0 0.5 ORDERING INFORMATION PART NUMBER PS7200A-1A PS7200A-1A-E3 PS7200A-1A-E4 PS7200A-1A-F3 PS7200A-1A-F4 Notes: 1. Operation in excess of any one of these parameters may result in permanent damage. 2. PW = 100 µs, Duty Cycle = 1 % 3. PW = 100 ms, 1 shot. 4. AC voltage for 1 minute at TA = 25 °C, RH = 60 % between input and output. Embossed tape 3500 pcs/reel PACKAGE 4-pin SOP PACKING STYLE Magazine case 100 pcs Embossed tape 900 pcs/reel TYPICAL PERFORMANCES CURVES (TA = 25˚C) MAXIMUM FORWARD CURRENT vs. AMBIENT TEMPERATURE 100 150 MAXIMUM LOAD CURRENT vs. AMBIENT TEMPERATURE Maximum Forward Current, IF (mA) 80 Maximum Load Current, IL (mA) 100 60 40 50 20 0 -25 0 25 50 75 80 100 0 -25 0 25 50 75 80 100 Ambient Temperature (TA ˚C) FORWARD VOLTAGE vs. AMBIENT TEMPERATURE 1.6 5.0 Ambient Temperature (TA ˚C) OUTPUT CAPACITANCE vs. APPLIED VOLTAGE f = 1 MHz 4.0 1.4 IF = 50 mA 1.2 30 mA 20 mA 10 mA 5 mA 1.0 1 mA Output Capacitance, COUT (pF) Forward Voltage, VF (V) 3.0 2.0 1.0 0.8 -25 0 25 50 75 100 0 0 5 10 15 20 25 30 Ambient Temperature (TA ˚C) Applied Voltage, VD (V) PS7200A-1A TYPICAL PERFORMANCE CURVES (TA = 25˚C) NORMALIZED ON-STATE RESISTANCE vs. AMBIENT TEMPERATURE 3.0 ON-STATE RESISTANCE DISTRIBUTION 30 n = 50 pcs IF = 10 mA IL = 10 mA Normalized On-state Resistance, Ron 2.5 Normalized to 1.0 at TA = 25˚C, IF = 10 mA IL = 10 mA 25 2.0 Number (pcs) 20 1.5 15 1.0 10 5 0.5 0 0.0 -25 8.8 9.0 9.2 9.4 9.6 0 25 50 75 100 Ambient Temperature,TA (˚C) On-state Resistance, Ron (Ω) OFF-STATE LEAKAGE CURRENT vs. APPLIED VOLTAGE 10-6 LOAD CURRENT vs. LOAD VOLTAGE IF = 10 mA 100 Off-state Leakage Current, ILoff (A) 10-7 TA = 80˚C Load Current, IL (mA) 10-8 50 10-9 25˚C -2.0 -1.0 0 1.0 2.0 10 -10 -50 10-11 10-12 0 10 20 30 40 50 -100 Applied Voltage, VCC (V) Load Voltage, VL (V) TURN-ON TIME vs. FORWARD CURRENT 0.05 VO = 5 V 0.04 TURN-OFF TIME vs. FORWARD CURRENT 0.5 VO = 5 V 0.4 Turn-on Time ton (mS) 0.03 Turn-off Time toff (mS) 0 5 10 15 20 25 30 0.3 0.02 0.2 0.01 0.1 0 0 5 10 15 20 25 30 Forward Current IF (mA) Forward Current IF (mA) PS7200A-1A TYPICAL PERFORMANCE CURVES (TA = 25˚C) TURN-ON TIME DISTRIBUTION 30 n = 50 pcs IF = 10 mA VO = 5 V 30 n = 50 pcs IF = 10 mA VO = 5 V TURN-OFF TIME DISTRIBUTION 25 25 (pcs) (pcs) TNumber 20 20 TNumber 15 15 10 10 5 5 0 0.01 0.02 0.03 0.04 0.05 0 0.06 0.08 Turn-on Time, ton (mS) NORMALIZED TURN-ON TIME vs. AMBIENT TEMPERATURE 3.0 Normalized to 1.0 at TA = 25˚C, IF = 10 mA VO = 5 V Turn-off Time, toff (mS) NORMALIZED TURN-OFF TIME vs. AMBIENT TEMPERATURE 3.0 Normalized to 1.0 at TA = 25˚C, IF = 10 mA VO = 5 V Normalized Turn-on Time, ton 2.5 Normalized Turn-off Time, ton 100 2.5 2.0 2.0 1.5 1.5 1.0 1.0 0.5 0.5 0.0 -25 0 25 50 75 0.0 -25 0 25 50 75 100 Ambient Temperature,TA (˚C) Ambient Temperature,TA (˚C) OUTLINE DIMENSIONS (Units in mm) PS7200A-1A TOP VIEW 4.0±0.5 4 3 1 2 7.0±0.3 4.4 2.05 +0.08 -0.05 +0.10 0.15 -0.05 0.5 +0.08 -0.05 0.4 -0.05 2.54 0.25 M +0.10 0.5±0.3 1. LED Anode 2. LED Cathode 3. MOS FET 4. MOS FET PS7200A-1A TAPING SPECIFICATIONS (Units in mm) Tape Outline and Dimensions 2.0 ± 0.1 1.75 ± 0.1 4.0 ± 0.1 1.55 ± 0.1 2.4 ± 0.1 5.5 ± 0.1 7.4 ± 0.1 12.0 ± 0.2 0.3 1.55 ± 0.1 4.6 ± 0.1 8.0 ± 0.1 Tape Direction PS7200A-1A-E3 PS7200A-1A-E4 Reel Outline and Dimensions 2.0 2.0±0.5 ø13.0±0.5 15° 15° ø21.0±0.8 13.0±0.5 ø180 ø60 13.0±1.0 Packing: 900 pcs/reel PS7200A-1A TAPING SPECIFICATIONS (Units in mm) Tape Outline and Dimensions 2.0 ± 0.1 1.75 ± 0.1 4.0 ± 0.1 1.55 ± 0.1 2.4 ± 0.1 5.5 ± 0.1 7.4 ± 0.1 12.0 ± 0.2 0.3 1.55 ± 0.1 4.6 ± 0.1 8.0 ± 0.1 Tape Direction PS7200A-1A-F3 PS7200A-1A-F4 Reel Outline and Dimensions 1.5 ± 0.1 1.5 ± 0.1 12 0° φ21.0 ± 0.8 1.5 ± 0.5 60 ° 6.0 ± 1 φ 330 2.0 ± 0.5 φ13.0±0.5 φ80±5.0 12.4 -0.0 +2.0 PS7200A-1A RECOMMENDED SOLDERING CONDITIONS (1) Infrared reflow soldering • Peak reflow temperature • Time of temperature higher than 210 °C • Number of reflows • Flux 235 °C or below (package surface temperature) 30 seconds or less Two Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt % is recommended.) Recommended Temperature Profile of Infrared Reflow Package Surface Temperature T (˚C) (heating) to 10 s 235 ˚C (peak temperature) 210 ˚C to 30 s 100 to 160 ˚C 60 to 120 s (preheating) Time (s) (2) Dip soldering • Temperature • Time • Number of times • Flux 260 °C or below (molten solder temperature) 10 seconds or less One Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt % is recommended.) (3) Cautions • Fluxes Avoid removing the residual flux with freon-based cleaning solvent. EXCLUSIVE NORTH AMERICAN AGENT FOR NEC RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS CALIFORNIA EASTERN LABORATORIES • Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054-1817 • (408) 988-3500 • Telex 34-6393 • FAX (408) 988-0279 Internet: http://WWW.CEL.COM DATA SUBJECT TO CHANGE WITHOUT NOTICE 09/04/2001