PS9714-V-F3

NEC's HIGH CMR, 10 Mbps OPEN COLLECTOR OUTPUT TYPE 5 PIN SOP OPTOCOUPLER FEATURES • HIGH COMMON MODE TRANSIENT IMMUNITY: CMH, CML: ± 20 kV/µs TYP • PULSE WIDTH DISTORTION: |tPHL - tPLH| = 3 ns TYP • HIGH SPEED RESPONSE: 10 Mbps • HIGH ISOLATION VOLTAGE: BV: 2500 Vr.m.s. • OPEN COLLECTOR OUTPUT TYPE • SMALL OUTLINE PACKAGE: 5 PIN SOP • TAPE AND REEL AVAILABLE: PS9714-F3, F4: 3500 Pcs/Reel • SAFETY STANDARDS: UL and VDE0884 approved PS9714 DESCRIPTION NEC's PS9714 is an optically coupled, high speed isolator containing a GaAIAs LED on the light emitting diode (input) side and a photodiode and a signal procesing circuit on the detector (output) side on one chip. The PS9714 is in a plastic SOP (Small Outline Package) for high density applications. APPLICATIONS • MEASUREMENT EQUIPMENT • PDP • FACTORY AUTOMATION NETWORK ELECTRICAL CHARACTERISTICS (TA = -40 to +85°C unless otherwise specified) PART NUMBER SYMBOLS PARAMETERS Forward Voltage, IF = 10 mA, TA = 25°C Reverse Current, VR = 3 V, TA = 25°C Terminal Capacitance, V = 0 V, f = 1 MHz, TA = 25°C High Level Output Current, VCC = VO = 5.5 V, VF = 0.8 V Low Level Output Voltage, VCC = 5.5 V, IF = 5 mA, IO = 13 mA High Level Supply Current, VCC = 5.5 V, IF = 0 mA Low Level Supply Current, VCC = 5.5 V, IF = 10 mA Threshold Input Current, VCC = 5 V, VO = 0.8 V, RL = 350 Ω Isolation Resistance,Vin-out = 1kVDC, RH = 40 to 60%, TA = 25°C Isolation Capacitance, V = 0, f = 1 MHz, TA = 25°C Propagation Delay Time, High → Low1,VCC = 5 V, IF = 7.5 mA, RL = 350 Ω TA = 25°C Propagation Delay Time, Low → High1, VCC = 5 V, IF = 7.5 mA, RL = 350 Ω TA = 25°C Rise Time, VCC = 5 V, IF = 7.5 mA, RL = 350 Ω Fall Time, VCC = 5 V, IF = 7.5 mA, RL = 350 Ω Pulse Width Distortion, VCC = 5 V, IF = 7.5 mA, RL = 350 Ω Propagation Skew, VCC = 5 V, IF = 7.5 mA, RL = 350 Ω Common Mode Transient Immunity at High Level Output2 VCC = 5 V, VCM = 1 kV, TA = 25°C, IF = 0 mA, VO (MIN) = 2 V Common Mode Transient Immunity at Low Level Output2 VCC = 5 V, VCM = 1 kV, TA = 25°C, IF = 7.5 mA, VO (MAX) = 0.8 V UNITS V µA pF µA V mA mA % Ω pF ns 54 ns 51 ns ns ns ns kV/µs kV/µs 10 10 20 20 20 10 3 50 60 1011 0.9 100 75 100 75 30 0.02 0.15 3 7.0 2.0 250 0.6 8 11 5.0 MIN 1.4 VF IR Ct IOH PS9714 TYP 1.65 MAX 1.9 10 Diode Detector VOL ICCH ICCL IFHL RI-O CI-O tPHL tPLH Coupled tr tf PWD tPSK CMH CML Please see notes on the next page. California Eastern Laboratories PS9714 ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C unless otherwise specified) SYMBOLS Diode IF VR Detector VCC VO IO PC BV TA TSTG PARAMETERS Forward Current Reverse Voltage Supply Voltage Output Voltage Output Current Power Dissipation2 Isolation Voltage3 Operating Ambient Temp. Storage Temperature UNITS mA V V V mA mW Vr.m.s. °C °C RATINGS 30 3 7 7 25 40 2500 -40 to +85 -55 to +125 RECOMMENDED OPERATING CONDITIONS SYMBOLS VFL IFH VCC N RL PARAMETERS Low Level Input Voltage High Level Input Current Supply Voltage TTL (loads) (RL = 1kΩ) Pull-up Resistance Ω 330 UNITS MIN TYP MAX V mA V 0 6.3 4.5 5 0.8 12.5 5.5 5 4k MARKING Notes: 1. Operation in excess of any one of these parameters may result in permanent damage. 2. Applies to output pin VO and power supply pin VCC. 2. AC voltage for 1 minute at TA = 25 °C, RH = 60 % between input and output. No. 1 Pin Mark 9714 N003 Assembly lot N 0 03 Week Assembled Year Assembled (Last 1 Digit) Rank Code ORDERING INFORMATION Part Number Packing Style Safety Standards Approval UL Approved VDE0884 Approved PS9714 PS9714-F3 PS9714-F4 PS9714-V PS9714-V-F3 PS9714-V-F4 Magazine Case 100 pcs Embossed Tape 3500 pcs/reel Magazine Case 100 pcs Embossed Tape 3500 pcs/reel PACKAGE OUTLINE (Units in mm) PIN CONNECTION (Top View) 4.0±0.5 5 4 3 1. 2. 3. 4. 5. Anode Cathode GND VO VCC 1 2 7.0 ± 0.3 2.0 4.4 0.15 +0.10 -0.05 1.3 2.1±0.2 0.1 ± 0.1 0.5 ± 0.3 1.27 0.4 +0.10 -0.05 0.25 M PS9714 (Continued from first page.) Notes: 1. Typical values at TA = 25°C. 2. Because VOL of 2 V or more may be output when LED current input and when output supply of VCC = 2.6 V or less, it is important to confirm the characteristics (operation with the power supply on and off) during design, before using this device. 3. Test Circuit for Propagation Delay Time: Pulse Input ( PW = 10 µs Duty Cycle = 1/10) ( 47 Ω 0.1 µF Vcc = 5 V RL = 350 Ω VO (monitor) CL Input IF = 7.5 mA 50 % VOH Input (monitor) Output 1.5 V VOL tPHL tPLH *CL is approximately 15 pF which includes probe and stray wiring capacitance. 4. Test Circuit for Common Mode Transient Immunity: GL SW IF 0.1 µF 90 % 1 kV VCM 10 % Vcc = 5 V RL VO (monitor) CL VO (IF = 0 mA) VOH 2V 0.8 V VOL tr tf 0V VCM VO (IF = 7.5 mA) USAGE CAUTIONS 1. Protect against static electricity when handling this product. 2. Bypass capacitor greater than 0.1 µF is used between VCC and GND near device (lead distance: 10 mm MAX). TYPICAL PERFORMANCE CURVES (TA = 25°C, unless otherwise specified) MAXIMUM FORWARD CURRENT vs. AMBIENT TEMPERATURE DETECTOR POWER DISSIPATION vs. AMBIENT TEMPERATURE 50 Maximum Forward Current, IF (mA) Detector Power Dissipation, PC (mW) 80 85 40 40 30 30 20 20 10 10 0 20 40 60 100 0 0 20 40 60 80 85 100 Ambient Temperature, TA (°C) Ambient Temperature, TA (°C) PS9714 TYPICAL PERFORMANCE CURVES (TA = 25°C, unless otherwise specified) FORWARD CURRENT vs. FORWARD VOLTAGE 100 DETECTOR POWER DISSIPATION vs. AMBIENT TEMPERATURE High Level Supply Current, ICCH (mA) Low Level Supply Current, ICCL (mA) 12 Forward Current, IF (mA) 10 10 TA = +85°C +50°C 1 +25°C 0°C -25°C 0.1 8 ICCL (IF = 10 mA) 6 4 ICCH (IF = 0 mA) 2 0.01 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 0 -50 -25 0 25 50 75 100 Forward Voltage, VF (V) Ambient Temperature, TA (°C) OUTPUT VOLTAGE vs. INPUT CURRENT 6 TA = 25°C 5 0.6 LOW LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE Low Level Output Voltage, VOL (V) VCC = 5.0 V, IF = 5.0 mA VCC = 5.5 V 0.5 Output Voltage, VO (V) 4 RL = 350 Ω 1.0 Ω 4.0 kΩ, 4.7 kΩ 0.4 IOL = 16.0 mA 13.0 mA 10.0 mA 6.0 mA 3 0.3 2 0.2 1 0.1 0 1 2 3 4 5 6 0 -50 -25 0 25 50 75 100 Input Current, IF (mA) Ambient Temperature, TA (°C) Propagation Delay Time, tPHL, tPLH (ns) THRESHOLD INPUT CURRENT vs. AMBIENT TEMPERATURE 2.5 PROPAGATION DELAY TIME vs. AMBIENT TEMPERATURE 100 IF = 7 mA VCC = 5.0 V 80 tPLH: RL = 1.0 kΩ tPLH: RL = 350 Ω Threshold Input Current, IFHL (mA) VCC = 5.0 V VO = 0.6 V 2.0 1.5 RL = 350 Ω 1.0 Ω 4.7 kΩ, 4.0 kΩ 60 40 tPHL: RL = 350 Ω, 1.0 kΩ 1.0 20 0.5 0 -50 0 -50 -25 0 25 50 75 100 -25 0 25 50 75 100 Ambient Temperature, TA (°C) Ambient Temperature, TA (°C) PS9714 TYPICAL PERFORMANCE CURVES (TA = 25°C, PROPAGATION DELAY TIME vs. AMBIENT TEMPERATURE unless otherwise specified) PULSE WIDTH DISTORTION vs. AMBIENT TEMPERATURE 60 Propagation Delay Time, tPHL, tPLH (ns) 120 100 tPLH: RL = 4.0 kΩ 80 tPHL: RL = 4.7 kΩ tPHL: RL = 4.0 kΩ 40 Pulse Width Distortion, |tPHL—tPLH| (ns) IF = 7.5 mA VCC = 5.0 V tPLH: RL = 4.7 kΩ IF = 7 mA VCC = 5.0 V 50 RL = 4.7 kΩ 40 4.0 kΩ 60 30 20 RL = 350 Ω 1.0 kΩ 20 10 0 -50 -25 0 25 50 75 100 0 -50 -25 0 25 50 75 100 Ambient Temperature, TA (°C) Ambient Temperature, TA (°C) SWITCHING TIME vs. AMBIENT TEMPERATURE IF = 7.5 mA VCC = 5.0 V tr: RL = 4.0 kΩ, 4.7 kΩ PROPAGATION DELAY TIME vs. INPUT CURRENT Propagation Delay Time, tPHL, tPLH (ns) 400 120 100 tPLH: RL = 4.0 kΩ 80 Switching Time, tr, tf (ns) 300 200 60 tr: RL = 1.0 kΩ tr: RL = 350 Ω 40 tPLH: RL = 1.0 kΩ tPLH: RL = 350 Ω 100 tr: RL = 350 Ω, 1.0 kΩ, 4.0 kΩ, 4.7 kΩ 20 tPHL: RL = 350 Ω, 1.0 kΩ, 4.0 kΩ VCC = 5.0 V, TA = 25°C 11 13 15 0 -50 -25 0 25 50 75 100 0 05 7 9 Ambient Temperature, TA (°C) Input Current, IF (mA) PS9714 TAPING SPECIFICATIONS Tape Outline and Dimensions 4.0±0.1 2.0±0.05 1.5 -0 +0.1 2.9 MAX 1.75±0.1 5.5±0.05 12±0.2 7.4±0.1 1.55±0.1 4.6±0.1 8±0.1 0.3 2.4±0.1 Tape Direction PS9714-F3 PS9714-F4 Reel Outline and Dimensions 1.5 ± 0.1 12 0° φ21.0 ± 0.8 φ80±5.0 1.5 ± 0.5 60 ° 6.0 ± 1 φ 330 2.0 ± 0.5 φ13.0±0.5 Packing: 3500 pcs/reel 12.4 -0.0 +2.0 PS9714 RECOMMENDED SOLDERING CONDITIONS (1) Infrared reflow soldering • Peak reflow temperature • Time of temperature higher than 210 ºC • Number of reflows • Flux 235 ûC or below (package surface temperature) 30 seconds or less Three Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt % is recommended.) Package Surface Temperature T (ßC) (heating) to 10 s 235 ßC (peak temperature) 210 ßC to 30 s 100 to 160 ßC 60 to 120 s (preheating) Time (s) (2) Cautions • Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. 02/12/2003 A Business Partner of NEC Compound Semiconductor Devices, Ltd.