PS9851-2-V-F3-A

PRELIMINARY DATA SHEET PHOTOCOUPLER PS9851-1,-2 HIGH NOISE REDUCTION, 15 Mbps CMOS OUTPUT TYPE 8-PIN SSOP PHOTOCOUPLER −NEPOC Series− DESCRIPTION The PS9851-1, -2 are optically coupled isolators containing GaAlAs LED on the input side and a CMOS output IC on the output side. They are high common mode transient immunity (CMR), high-speed CMOS output type photocouplers designed for high-speed logic interface circuits. FEATURES • High-speed response (15 Mbps) • Operable at high temperature (−40 to +100°C) • High common mode transient immunity (CMH, CML = ±15 kV/µs TYP.) • High isolation voltage (BV = 2 500 Vr.m.s.) • Pulse width distortion (tPHL−tPLH = 5 ns TYP.) • Ordering number of tape product : PS9851-1-F3, F4: 1 500 pcs/reel : PS9851-2-F3, F4: 1 500 pcs/reel • Safety standards • UL awaiting approved • DIN EN60747-5-2 (VDE0884 Part2) awaiting approved 1 2 3 4 SHIELD PIN CONNECTION (Top View) 8 7 PS9851-1 65 1. NC 2. Anode 3. Cathode 4. NC 5. GND 6. VO 7. NC 8. VDD 8 7 • FA Network • Measurement equipment • PDP 1 2 The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Not all devices/types available in every country. Please check with local NEC Compound Semiconductor Devices representative for availability and additional information. Document No. PN10493EJ01V0DS (1st edition) Date Published May 2004 CP(K) Printed in Japan  NEC Compound Semiconductor Devices 2004 SHIELD APPLICATIONS PS9851-2 65 1. Anode1 2. Cathode1 3. Cathode2 4. Anode2 5. GND 6. VO2 7. VO1 8. VDD 34 PS9851-1,-2 PACKAGE DIMENSIONS (UNIT: mm) 5.21±0.25 (include burr) 5.08±0.15 6.0±0.2 3.95±0.1 3.27±0.2 0.15 +0.10 –0.05 0.1±0.1 1.27 0.4 +0.10 –0.05 0.25 M 0.5±0.3 0.10 S MARKING EXAMPLE PS9851-1 PS9851-2 9851-1 N451 N N 4 51 No. 1 pin Mark Initial of NEC (Engraved mark) Type Number Assembly Lot *1 9851-2 N451 N N 4 51 No. 1 pin Mark Initial of NEC (Engraved mark) Type Number Assembly Lot *1 Week Assembled Year Assembled (Last 1 Digit) Rank Code Week Assembled Year Assembled (Last 1 Digit) Rank Code *1 For the external plating Sn-Bi product, L is indicated at the second digit of the rank. *1 For the external plating Sn-Bi product, L is indicated at the second digit of the rank. 2 Preliminary Data Sheet PN10493EJ01V0DS PS9851-1,-2 ORDERING INFORMATION Part Number Package Packing Style Safety Standards Approval PS9851-1 PS9851-1-F3 PS9851-1-F4 PS9851-2 PS9851-2-F3 PS9851-2-F4 PS9851-1-V PS9851-1-V-F3 PS9851-1-V-F4 PS9851-2-V PS9851-2-V-F3 PS9851-2-V-F4 PS9851-1-A PS9851-1-F3-A PS9851-1-F4-A PS9851-2-A PS9851-2-F3-A PS9851-2-F4-A PS9851-1-V-A PS9851-1-V-F3-A PS9851-1-V-F4-A PS9851-2-V-A PS9851-2-V-F3-A PS9851-2-V-F4-A 20 pcs (Tape 20 pcs cut) Embossed Tape 1 500 pcs/reel 20 pcs (Tape 20 pcs cut) Embossed Tape 1 500 pcs/reel DIN EN60747-5-2 (VDE0884 Part2) awaiting approved (Option) PS9851-2 PS9851-1 20 pcs (Tape 20 pcs cut) Embossed Tape 1 500 pcs/reel 20 pcs (Tape 20 pcs cut) Embossed Tape 1 500 pcs/reel Standard products (UL awaiting approved) PS9851-2 Sn-Bi PS9851-1 20 pcs (Tape 20 pcs cut) Embossed Tape 1 500 pcs/reel 20 pcs (Tape 20 pcs cut) Embossed Tape 1 500 pcs/reel DIN EN60747-5-2 (VDE0884 Part2) awaiting approved (Option) PS9851-2 PS9851-1 20 pcs (Tape 20 pcs cut) Embossed Tape 1 500 pcs/reel 8-pin SSOP (SO-8) 20 pcs (Tape 20 pcs cut) Embossed Tape 1 500 pcs/reel Standard products (UL awaiting approved) PS9851-2 Solder plating specification Sn-Pb Application Part Number PS9851-1 *1 *1 For the application of the Safety Standard, following part number should be used. Preliminary Data Sheet PN10493EJ01V0DS 3 PS9851-1,-2 ABSOLUTE MAXIMUM RATINGS (TA = 25°C, unless otherwise specified) Parameter Diode Forward Current Reverse Voltage Detector Symbol IF VR VDD VO IO BV TA Tstg Ratings 20 5 0 to 5.5 −0.5 to VDD+0.5 2 2 500 −40 to +100 −55 to +125 Unit mA V V V mA Vr.m.s. °C °C Supply Voltage Output Voltage Output Current Isolation Voltage *1 Operating Ambient Temperature Storage Temperature *1 AC voltage for 1 minute at TA = 25°C, RH = 60% between input and output. RECOMMENDED OPERATING CONDITIONS (TA = 25°C) Parameter Forward Current Supply Voltage Symbol IF VDD MIN. 10 4.5 5.0 TYP. MAX. 16 5.5 Unit mA V 4 Preliminary Data Sheet PN10493EJ01V0DS PS9851-1,-2 ELECTRICAL specified) CHARACTERISTICS (TA = −40 to +100°C, VDD = 4.5 to 5.5 V, unless otherwise Parameter Diode Forward Voltage Reverse Current Terminal Capacitance Detector High Level Supply Current Low Level Supply Current High Level Output Voltage Low Level Output Voltage Coupled Threshold Input Current Isolation Resistance Symbol VF IR Ct IDDH IDDL VOH VOL IFHL RI-O Conditions IF = 10 mA, TA = 25°C VR = 3 V, TA = 25°C V = 0 V, f = 1 MHz, TA = 25°C IF = 0 mA (1ch) IF = 10 mA (1ch) IO = −20µA, IF = 0 mA IO = 20µA, IF = 10 mA VO < 1 V VI-O = 1 kVDC, RH = 40 to 60%, TA = 25°C V = 0 V, f = 1 MHz, TA = 25°C IF = 10 mA, VDD = 5 V, CL = 15 pF, CMOS Levels MIN. TYP. 1.6 *1 MAX. 1.9 10 Unit V µA pF 30 3 3 4.0 5.0 0.01 0.1 6 10 11 5 5 mA V mA Ω Isolation Capacitance Propagation Delay Time (H → L) *2 CI-O tPHL 0.9 35 60 pF ns Propagation Delay Time (L → H) *2 tPLH 30 60 Pulse Width Pulse Width Distortion (PWD) Propagation Delay Skew Rise Time Fall Time Common Mode Transient Immunity at High Level Output Common Mode Transient Immunity at Low Level Output *3 *3 PW tPHL−tPLH 100 5 30 tPSK tr tf CMH VDD = 5 V, IF = 0 mA, VCM = 1 kV, VO > 4 V, TA = 25°C 10 3 3 15 40 kV/µs CML VDD = 5 V, IF = 10 mA, VCM = 1 kV, VO < 1 V, TA = 25°C 10 15 *1 Typical values at TA = 25°C Preliminary Data Sheet PN10493EJ01V0DS 5 PS9851-1,-2 *2 Test circuit for propagation delay time PS9851-1 Pulse input (IF) (PW = 100 ns, Duty cycle = 50%) Input (Monitor) 47 Ω VDD = 5 V 0.1 µ F VO (Monitor) CL = 15 pF Input IF = 10 mA 50% Output PS9851-2 Pulse input (IF) Input (Monitor) 47 Ω VDD = 5 V 0.1 µ F VO (Monitor) CL = 15 pF tPHL tPLH 2.5 V VOL Remark CL includes probe and stray wiring capacitance. *3 Test circuit for common mode transient immunity PS9851-1 VDD = 5 V IF 0.1 µF SW VO (Monitor) CL = 15 pF VCM 90% 10% VCM tr VO (IF = 0 mA) VO (IF = 10 mA) tf VOH 4V 1V SW 0.1 µF VO (Monitor) VOL 1 kV 0V IF PS9851-2 VDD = 5 V CL = 15 pF VCM Remark CL includes probe and stray wiring capacitance. USAGE CAUTIONS 1. 2. 3. This product is weak for static electricity by designed with high-speed integrated circuit so protect against static electricity when handling. By-pass capacitor of more than 0.1 µF is used between VDD and GND near device. Also, ensure that the distance between the leads of the photocoupler and capacitor is no more than 10 mm. Avoid storage at a high temperature and high humidity. 6 Preliminary Data Sheet PN10493EJ01V0DS PS9851-1,-2 TAPING SPECIFICATIONS (UNIT: mm) Outline and Dimensions (Tape) 5.56±0.1 2.0±0.05 4.0±0.1 1.75±0.1 1.5+0.1 –0 4.05 MAX. 1.7±0.1 8.0±0.1 12.0±0.2 5.5±0.1 6.4±0.1 3.6±0.1 0.3±0.05 Taping Direction PS9851-1-F3 PS9851-2-F3 PS9851-1-F4 PS9851-2-F4 Outline and Dimensions (Reel) 2.0±0.5 2.0±0.5 φ13.0±0.2 R 1.0 φ 21.0±0.8 φ 330±2.0 φ 13.0±0.2 φ 100±1.0 13.5±1.0 17.5±1.0 Packing: 1 500 pcs/reel 11.9 to 15.4 Outer edge of flange Preliminary Data Sheet PN10493EJ01V0DS 7 PS9851-1,-2 NOTES ON HANDLING 1. Recommended soldering conditions (1) Infrared reflow soldering • Peak reflow temperature • Time of peak reflow temperature • Time of temperature higher than 220°C • Time to preheat temperature from 120 to 180°C • Number of reflows • Flux 260°C or below (package surface temperature) 10 seconds or less 60 seconds or less 120±30 s Three Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) Recommended Temperature Profile of Infrared Reflow Package Surface Temperature T (˚C) (heating) to 10 s 260˚C MAX. 220˚C to 60 s 180˚C 120˚C 120±30 s (preheating) Time (s) (2) Wave soldering • Temperature • Time • Preheating conditions • Number of times • Flux 260°C or below (molten solder temperature) 10 seconds or less 120°C or below (package surface temperature) One (Allowed to be dipped in solder including plastic mold portion.) Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (3) Cautions • Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. 2. Cautions regarding noise Be aware that when voltage is applied suddenly between the photocoupler’s input and output or between collector-emitters at startup, the output side may enter the on state, even if the voltage is within the absolute maximum ratings. 8 Preliminary Data Sheet PN10493EJ01V0DS PS9851-1,-2 • The information in this document is current as of May, 2004. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC's data sheets or data books, etc., for the most up-to-date specifications of NEC semiconductor products. Not all products and/or types are available in every country. Please check with an NEC sales representative for availability and additional information. • No part of this document may be copied or reproduced in any form or by any means without prior written consent of NEC. NEC assumes no responsibility for any errors that may appear in this document. • NEC does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC semiconductor products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC or others. • Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of customer's equipment shall be done under the full responsibility of customer. NEC assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. • While NEC endeavours to enhance the quality, reliability and safety of NEC semiconductor products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC semiconductor products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment, and anti-failure features. • NEC semiconductor products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to semiconductor products developed based on a customer-designated "quality assurance program" for a specific application. The recommended applications of a semiconductor product depend on its quality grade, as indicated below. Customers must check the quality grade of each semiconductor product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC semiconductor products is "Standard" unless otherwise expressly specified in NEC's data sheets or data books, etc. If customers wish to use NEC semiconductor products in applications not intended by NEC, they must contact an NEC sales representative in advance to determine NEC's willingness to support a given application. (Note) (1) "NEC" as used in this statement means NEC Corporation, NEC Compound Semiconductor Devices, Ltd. and also includes its majority-owned subsidiaries. (2) "NEC semiconductor products" means any semiconductor product developed or manufactured by or for NEC (as defined above). M8E 00. 4 - 0110 Preliminary Data Sheet PN10493EJ01V0DS 9 PS9851-1,-2 Caution GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. • Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. • Do not burn, destroy, cut, crush, or chemically dissolve the product. • Do not lick the product or in any way allow it to enter the mouth. For further information, please contact NEC Compound Semiconductor Devices, Ltd. http://www.ncsd.necel.com/ E-mail: salesinfo@ml.ncsd.necel.com (sales and general) techinfo@ml.ncsd.necel.com (technical) 5th Sales Group, Sales Division TEL: +81-44-435-1588 FAX: +81-44-435-1579 NEC Compound Semiconductor Devices Hong Kong Limited E-mail: ncsd-hk@elhk.nec.com.hk (sales, technical and general) FAX: +852-3107-7309 TEL: +852-3107-7303 Hong Kong Head Office TEL: +886-2-8712-0478 FAX: +886-2-2545-3859 Taipei Branch Office FAX: +82-2-558-5209 TEL: +82-2-558-2120 Korea Branch Office NEC Electronics (Europe) GmbH http://www.ee.nec.de/ TEL: +49-211-6503-0 FAX: +49-211-6503-1327 California Eastern Laboratories, Inc. http://www.cel.com/ TEL: +1-408-988-3500 FAX: +1-408-988-0279 0401