UPB1511TB

800 MHz INPUT DIVIDE BY 2, 4 PRESCALER IC, UPB1511TB FOR PORTABLE SYSTEMS FEATURES • SUPPLY VOLTAGE VCC = 2.4 to 3.3 V • OPERATING FREQUENCY fIN = 50 to 700 MHz at ÷ 2 50 to 800 MHz at ÷ 4 • LOW CURRENT CONSUMPTION 3.5 mA at VCC = 3.0 V • SELECTABLE DIVISION ÷ 2, ÷ 4 • HIGH-DENSITY SURFACE MOUNTING 6-pin super minimold 1 000 pF 3 SW 2 GND 1 OUT IN 4 1 000 pF IN 5 TEST CIRCUIT 1 000 pF Vcc 6 1 000 pF 1 000 pF DESCRIPTION The UPB1511TB is a silicon monolithic integrated circuit designed as a divide by 2,4 prescaler IC for portable radio systems. This IC is manufactured using NEC's 30 GHz fMAX UHS0 (Ultra High Speed Process) silicon bipolar process. Consequently, this IC is lower circuit current and smaller package than conventional UPB1509GV. The low power makes this device ideally suited for cellular and cordless telephone applications. NEC's stringent quality assurance and test procedures ensure the highest reliability and performance. Power Supply APPLICATIONS • Portable radio systems • Cellular/cordless telephone 2nd local prescaler ELECTRICAL CHARACTERISTICS (TA = +25°C, VCC = 3.0 V) PART NUMBER PACKAGE OUTLINE SYMBOLS ICC fIN (u)1 fIN (u)2 fIN (L)1 fIN (L)2 PIN1 PIN2 VOUT VIH VIL PARAMETERS AND CONDITIONS Circuit Current, No Signals Upper Limit Operating Frequency 1, PIN = -20 to 0 dBm Upper Limit Operating Frequency 2, PIN = -20 to -5 dBm @ ÷ 2 @ ÷4 Lower Limit Operating Frequency 1, PIN = -20 to 0 dBm Lower Limit Operating Frequency 2, PIN = -20 to -5 dBm Input Power 1, fIN = 50 to 800 MHz Input Power 2, fIN = 50 to 500 MHz Output Voltage, RL = 200 Ω Divide Ratio Control Input High Divide Ratio Control Input Low MHz MHz dBm dBm VP-P V V -20 -20 0.2 0.7 x VCC -0.5 0.3 VCC + 0.5 VCC x 0.3 UNITS mA MHz MHz MIN 3.1 500 700 800 50 500 -5 0 UPB1511TB TYP 3.5 MAX 4.1 California Eastern Laboratories UPB1511TB ABSOLUTE MAXIMUM RATINGS1 SYMBOLS VCC VIN PD TA TSTG PARAMETERS Supply Voltage TA = +25° C Input Voltage TA = +25° C, SW Pin Total Power Dissipation2 (TA = +85° C) Operating Ambient Temp. Storage Temperature UNITS V V mW °C °C RATINGS 3.6 3.6 200 -40 to +85 -55 to +150 RECOMMENDED OPERATING CONDITIONS SYMBOLS VCC TA PARAMETERS Supply Voltage Operating Ambient Temp. UNITS MIN V °C 2.4 -40 TYP MAX 3.0 +25 3.3 +85 SYSTEM APPLICATION EXAMPLE LNA RX DEMOD. I Q Notes: 1. Operation in excess of any one of these conditions may result in permanent damage. 2. Mounted on double sided copper clad 50 x 50 x 1.6mm epoxy glass PWB VCO VCO SW ÷N UPB1511TB I 0˚ TX Phase Shifter 90˚ Q ÷N PLL PLL INTERNAL BLOCK DIAGRAM D IN CLK IN Q CLK Q OUT Q D Q PA SW PRODUCT LINE-UP PART NUMBER ICC (mA) UPB1509 GV UPB1511 TB 5.0 3.5 VCC (V) 2.2 to 5.5 2.4 to 3.3 ÷2 fIN (MHZ) 50 to 700 50 to 700 ÷4 fIN (MHZ) 50 to 800 50 to 800 ÷8 fIN (MHZ) 50 to 1000 8-pin SSOP 6-pin super minimold PACKAGE PIN EXPLANATIONS PIN NO. 1 SYMBOL OUT APPLIED VOLTAGE (V) – FUNCTIONS AND EXPLANATION Divided Frequency Output Pin. This pin is designed as an emitter follower output and can deliver 0.2 VP-P minimum into a 200 Ω load. This pin should be coupled to the load device with a capacitor (example: 1000 pF) for DC cut. Ground Pin. Ground pattern on the board should be as wide as possible to minimize ground impedance. Divide Ratio Control Pin. Divide ratio can be determined by the following applied level to these pins. 2 3 GND SW 0 H/L SW Divide ratio H 1/2 L 1/4 These pins must be each equipped with bypass capacitor to minimize their impedance. 4 5 6 IN IN VCC – – 2.4 TO 3.3 Signal Input Pin. This pin should be coupled to the signal source with a capacitor (example: 1000 pF) for DC cut. Signal Input Bypass Pin. This pin must be equipped with a bypass capacitor (example: 1000 pF) to minimize ground impedance. Power Supply Pin. This pin must be equipped with a bypass capacitor (example: 1000 pF) to minimize ground impedance. UPB1511TB OUTLINE DIMENSIONS (Units in mm) 6-PIN SUPER MINIMOLD 2.1 ±0.1 1.25 ±0.1 PIN CONNECTIONS (Top View) (Bottom View) C2Z 3 0.2 ±0.1 4 5 6 4 5 6 3 2 1 2 1 0.65 TEST CIRCUIT 2.0 ±0.2 0.9 ±0.1 High Impedance Oscilloscope 50 Ω Counter (or Spectrum Analyzer) Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. CALIFORNIA EASTERN LABORATORIES • Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054-1817 • (408) 988-3500 • Telex 34-6393 • FAX (408) 988-0279 Internet: http://WWW.CEL.COM DATA SUBJECT TO CHANGE WITHOUT NOTICE 07/18/2002 1.3 1 000 pF 150 Ω EXCLUSIVE NORTH AMERICAN AGENT FOR NEC RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS 0.65 0.1 MIN PIN CONNECTION 1. OUT 2. GND 3. SW 4. IN 5. IN 6. VCC 0.7 0.15 +0.1 -0 0 to 0.1 3 SW 2 GND 1 OUT IN 4 IN 5 Vcc 6 1 000 pF ORDERING INFORMATION PART NUMBER UPB1511TB-E3 1 000 pF 50 Ω Signal Generator PACKAGE 6-pin super minimold QUANTITY Qty 3 kpcs/reel. 1 000 pF Notes: 1. Embossed tape 8 mm wide. Pin 1, 2, 3 face the tape perforation side. 1 000 pF Power Supply Divide Ratio Setting SW H L 1/2 1/4