UPC2909HB

DATA SHEET BIPOLAR ANALOG INTEGRATED CIRCUIT µPC2900 Series THREE TERMINAL LOW DROPOUT VOLTAGE REGULATOR The µPC2900 series of low dropout voltage three terminal positive regulators is constructed with PNP output transistor. The µPC2900 series feature the ability to source 1 A of output current with a low dropout voltage of typically 0.7 V. The power dissipation of the µPC2900 series can be drastically reduced compared with the conventional three terminal positive voltage regulators that is constructed with NPN output transistor. Also, this series corresponds to the low voltage output (3 V, 3.3 V) which is not in the conventional low dropout regulators (µPC2400A series). FEATURES • Output current in excess of 1.0 A • Low dropout voltage VDIF = 0.7 V TYP. (at IO = 1 A) • On-chip overcurrent and thermal protection circuit • On-chip output transistor safe area protection circuit PIN CONFIGURATION (Marking Side) µPC2900HF Series: MP-45G µPC2900HB Series: MP-3 µPC2900T Series: MP-3Z 4 1 2 3 1: INPUT 2: GND 3: OUTPUT 1 2 3 1: 2: 3: 4: INPUT GND OUTPUT GND (Fin) The information in this document is subject to change without notice. Document No. G10026EJ3V0DS00 (3rd edition) Date Published July 1998 N CP(K) Printed in Japan The mark shows major revised points. © 1997 µPC2900 Series BLOCK DIAGRAM INPUT Safe operating area protection Start-up circuit Reference voltage Error amp. Drive circuit Saturation protection OUTPUT Thermal shut down Over current protection GND ORDERING INFORMATION Part Number Package MP-45G (Isolated TO-220) MP-3 (SC-64) MP-3Z (SC-63) MP-45G (Isolated TO-220) MP-3 (SC-64) MP-3Z (SC-63) MP-45G (Isolated TO-220) MP-3 (SC-64) MP-3Z (SC-63) MP-45G (Isolated TO-220) MP-3 (SC-64) MP-3Z (SC-63) MP-45G (Isolated TO-220) MP-3 (SC-64) MP-3Z (SC-63) MP-45G (Isolated TO-220) MP-3 (SC-64) MP-3Z (SC-63) MP-45G (Isolated TO-220) MP-3 (SC-64) MP-3Z (SC-63) MP-45G (Isolated TO-220) MP-3 (SC-64) MP3Z (SC-63) MP-45G (Isolated TO-220) MP-3 (SC-64) MP-3Z (SC-63) Output Voltage 3.0 V 3.0 V 3.0 V 3.3 V 3.3 V 3.3 V 5.0 V 5.0 V 5.0 V 6.0 V 6.0 V 6.0 V 7.0 V 7.0 V 7.0 V 8.0 V 8.0 V 8.0 V 9.0 V 9.0 V 9.0 V 10.0 V 10.0 V 10.0 V 12.0 V 12.0 V 12.0 V µPC2903HF µPC2903HB µPC2903T µPC2933HF µPC2933HB µPC2933T µPC2905HF µPC2905HB µPC2905T µPC2906HF µPC2906HB µPC2906T µPC2907HF µPC2907HB µPC2907T µPC2908HF µPC2908HB µPC2908T µPC2909HF µPC2909HB µPC2909T µPC2910HF µPC2910HB µPC2910T µPC2912HF µPC2912HB µPC2912T 2 µPC2900 Series ABSOLUTE MAXIMUM RATINGS (TA = 25 °C, Unless otherwise specified.) Rating Parameter Input Voltage Internal Power DissipationNote Symbol VIN PT TA TJ Tstg Rth (J-C) Rth (J-A) 7 65 15 –30 to +85 –30 to +150 –55 to +150 12.5 125 µPC2900HF 20 µPC2900HB, µPC2900T Unit V 10 W °C °C °C °C/W °C/W Operating Ambient Temperature Operating Junction Temperature Storage Temperature Thermal Resistance (Junction to Case) Thermal Resistance (Junction to Ambient) Note TC = 25 °C, Internally limited When operating junction temperature rises up to 150 °C, the internal circuit shutdown output voltage. Caution Exposure to Absolute Maximum Ratings for extended periods may affect device reliability; exceeding the ratings could cause permanent damage. The parameters apply independently. The device should be operated within the limits specified under DC and AC Characteristics. TYPICAL CONNECTION D1 INPUT µ PC2900 OUTPUT + D2 CIN COUT CIN COUT D1 D2 : More than 0.1 µF. Required if regulator is located an appreciable distance from power supply filter. You must use to prevent from the parasitic oscillation. : More than 47 µF. You must use the Low-impedance-type (low ESR) capacitor. : Need for VO > VIN : Need a shottky barrier diode for VO < GND. 3 µPC2900 Series RECOMMENDED OPERATING CONDITIONS Parameter Input Voltage Symbol VIN Type Number MIN. 4.0 4.3 6 7 8 9 10 11 13 0 –30 –30 TYP. MAX. 16 16 16 16 16 18 18 18 18 1.0 +85 +125 A °C °C Unit V µPC2903 µPC2933 µPC2905 µPC2906 µPC2907 µPC2908 µPC2909 µPC2910 µPC2912 Output Current Operating Ambient Temperature Operating Junction Temperature IO TA TJ all all all ELECTRICAL CHARACTERISTICS µ PC2903 (TJ = 25 °C, VIN = 5 V, IO = 500 mA, CIN = 0.22 µF, COUT = 47 µF, unless otherwise specified.) Parameters Output Voltage Symbol VO 0 °C ≤ TJ ≤ 125 °C, 4.0 V ≤ VIN ≤ 16 V, 0 A ≤ IO ≤ 500 mA 0 °C ≤ TJ ≤ 125 °C, 0 A ≤ IO ≤ 1 A Line Regulation Load Regulation Quiescent Current REGIN REGL IBIAS 4.0 V ≤ VIN ≤ 16 V 0 A ≤ IO ≤ 1 A IO = 0 A IO = 1 A Startup Quiescent Current IBIAS (s) VIN = 2.95 V, IO = 0 A VIN = 2.95 V, IO = 1 A Quiescent Current Change Output Noise Voltage Ripple Rejection Dropout Voltage Short Circuit Current ∆IBIAS Vn R·R VDIF IO short 0 °C ≤ TJ ≤ 125 °C, 4.0 V ≤ VIN ≤ 16 V 10 Hz ≤ f ≤ 100 kHz f = 120 Hz, 4.0 V ≤ VIN ≤ 16 V 0 °C ≤ TJ ≤ 125 °C, IO = 1 A VIN = 4.5 V VIN = 16 V Peak Output Current IO peak VIN = 4.5 V VIN = 16 V Temperature Coefficient of Output Voltage ∆V O / ∆ T 0 °C ≤ TJ ≤ 125 °C, IO = 5 mA 1.0 1.3 1.2 48 3.2 52 63 0.7 1.7 1.2 1.5 1.7 –0.5 3.0 2.8 mV/°C A 1.0 3.0 11 9 1.9 23 12 30 30 4.0 60 30 80 20 mA mA mV mV mA Conditions MIN. 2.88 2.85 TYP. 3.0 MAX. 3.12 3.15 Unit V µVr.m.s. dB V A 4 µPC2900 Series ELECTRICAL CHARACTERISTICS µ PC2933 (TJ = 25 °C, VIN = 5 V, IO = 500 mA, CIN = 0.22 µF, COUT = 47 µF, unless otherwise specified.) Parameters Output Voltage Symbol VO 0 °C ≤ TJ ≤ 125 °C, 4.3 V ≤ VIN ≤ 16 V, 0 A ≤ IO ≤ 500 mA 0 °C ≤ TJ ≤ 125 °C, 0 A ≤ IO ≤ 1 A Line Regulation Load Regulation Quiescent Current REGIN REGL IBIAS 4.3 V ≤ VIN ≤ 16 V 0 A ≤ IO ≤ 1 A IO = 0 A IO = 1 A Startup Quiescent Current IBIAS (s) VIN = 3.1 V, IO = 0 A VIN = 3.1 V, IO = 1 A Quiescent Current Change Output Noise Voltage Ripple Rejection Dropout Voltage Short Circuit Current ∆IBIAS Vn R·R VDIF IO short 0 °C ≤ TJ ≤ 125 °C, 4.3 V ≤ VIN ≤ 16 V 10 Hz ≤ f ≤ 100 kHz f = 120 Hz, 4.3 V ≤ VIN ≤ 16 V 0 °C ≤ TJ ≤ 125 °C, IO = 1 A VIN = 4.5 V VIN = 16 V Peak Output Current IO peak VIN = 4.5 V VIN = 16 V Temperature Coefficient of Output Voltage ∆V O / ∆ T 0 °C ≤ TJ ≤ 125 °C, IO = 5 mA 1.0 1.3 1.2 48 3.0 55 64 0.7 1.6 1.2 1.4 1.7 –0.4 3.0 2.8 mV/°C A 1.0 3.0 12 23 2.0 30 10 33 33 4.0 60 30 80 20 mA mA mV mV mA Conditions MIN. 3.17 3.14 TYP. 3.3 MAX. 3.43 3.46 Unit V µVr.m.s. dB V A 5 µPC2900 Series ELECTRICAL CHARACTERISTICS µ PC2905 (TJ = 25 °C, VIN = 8 V, IO = 500 mA, CIN = 0.22 µF, COUT = 47 µF, unless otherwise specified.) Parameters Output Voltage Symbol VO 0 °C ≤ TJ ≤ 125 °C, 6 V ≤ VIN ≤ 16 V, 0 A ≤ IO ≤ 500 mA 0 °C ≤ TJ ≤ 125 °C, 0 A ≤ IO ≤ 1 A Line Regulation Load Regulation Quiescent Current REGIN REGL IBIAS 6 V ≤ VIN ≤ 16 V 0 A ≤ IO ≤ 1 A IO = 0 A IO = 1 A Startup Quiescent Current IBIAS (s) VIN = 4.5 V, IO = 0 A VIN = 4.5 V, IO = 1 A Quiescent Current Change Output Noise Voltage Ripple Rejection Dropout Voltage Short Circuit Current ∆IBIAS Vn R·R VDIF IO short 0 °C ≤ TJ ≤ 125 °C, 6 V ≤ VIN ≤ 16 V 10 Hz ≤ f ≤ 100 kHz f = 120 Hz, 6 V ≤ VIN ≤ 16 V 0 °C ≤ TJ ≤ 125 °C, IO = 1 A VIN = 6.5 V VIN = 16 V Peak Output Current IO peak VIN = 6.5 V VIN = 16 V Temperature Coefficient of Output Voltage ∆V O / ∆ T 0 °C ≤ TJ ≤ 125 °C, IO = 5 mA 1.1 1.4 1.15 46 2.9 90 61 0.7 1.8 1.1 1.5 2.0 0.6 3.0 2.8 mV/°C A 1.0 3.0 23 28 2.2 30 10 50 50 4.0 60 30 80 20 mA mA mV mV mA Conditions MIN. 4.8 4.75 TYP. 5.0 MAX. 5.2 5.25 Unit V µVr.m.s. dB V A 6 µPC2900 Series ELECTRICAL CHARACTERISTICS µ PC2906 (TJ = 25 °C, VIN = 9 V, IO = 500 mA, CIN = 0.22 µF, COUT = 47 µF, unless otherwise specified.) Parameters Output Voltage Symbol VO 0 °C ≤ TJ ≤ 125 °C, 7 V ≤ VIN ≤ 16 V, 0 A ≤ IO ≤ 500 mA 0 °C ≤ TJ ≤ 125 °C, 0 A ≤ IO ≤ 1 A Line Regulation Load Regulation Quiescent Current REGIN REGL IBIAS 7 V ≤ VIN ≤ 16 V 0 A ≤ IO ≤ 1 A IO = 0 A IO = 1 A Startup Quiescent Current IBIAS (s) VIN = 5.5 V, IO = 0 A VIN = 5.5 V, IO = 1 A Quiescent Current Change Output Noise Voltage Ripple Rejection Dropout Voltage Short Circuit Current ∆IBIAS Vn R·R VDIF IO short 0 °C ≤ TJ ≤ 125 °C, 7 V ≤ VIN ≤ 16 V 10 Hz ≤ f ≤ 100 kHz f = 120 Hz, 7 V ≤ VIN ≤ 16 V 0 °C ≤ TJ ≤ 125 °C, IO = 1 A VIN = 7.5 V VIN = 16 V Peak Output Current IO peak VIN = 7.5 V VIN = 16 V Temperature Coefficient of Output Voltage ∆V O / ∆ T 0 °C ≤ TJ ≤ 125 °C, IO = 5 mA 1.1 1.4 44 2.2 108 60 0.7 1.8 1.1 1.5 2.0 0.6 3.0 2.8 mV/°C A 1.0 25 29 2.0 23 10 60 60 4.0 60 30 80 20 mA mA mV mV mA Conditions MIN. 5.76 5.70 TYP. 6.0 MAX. 6.24 6.30 Unit V µVr.m.s. dB V A 7 µPC2900 Series ELECTRICAL CHARACTERISTICS µ PC2907 (TJ = 25 °C, VIN = 10 V, IO = 500 mA, CIN = 0.22 µF, COUT = 47 µF, unless otherwise specified.) Parameters Output Voltage Symbol VO 0 °C ≤ TJ ≤ 125 °C, 8 V ≤ VIN ≤ 16 V, 0 A ≤ IO ≤ 500 mA 0 °C ≤ TJ ≤ 125 °C, 0 A ≤ IO ≤ 1 A Line Regulation Load Regulation Quiescent Current REGIN REGL IBIAS 8 V ≤ VIN ≤ 16 V 0 A ≤ IO ≤ 1 A IO = 0 A IO = 1 A Startup Quiescent Current IBIAS (s) VIN = 6.5 V, IO = 0 A VIN = 6.5 V, IO = 1 A Quiescent Current Change Output Noise Voltage Ripple Rejection Dropout Voltage Short Circuit Current ∆IBIAS Vn R·R VDIF IO short 0 °C ≤ TJ ≤ 125 °C, 8 V ≤ VIN ≤ 16 V 10 Hz ≤ f ≤ 100 kHz f = 120 Hz, 8 V ≤ VIN ≤ 16 V 0 °C ≤ TJ ≤ 125 °C, IO = 1 A VIN = 8.5 V VIN = 16 V Peak Output Current IO peak VIN = 8.5 V VIN = 16 V Temperature Coefficient of Output Voltage ∆V O / ∆ T 0 °C ≤ TJ ≤ 125 °C, IO = 5 mA 1.1 1.4 43 2.3 126 59 0.7 1.8 1.1 1.5 2.0 0.6 3.0 2.8 mV/°C A 1.0 27 30 2.0 24 10 70 70 4.0 60 30 80 20 mA mA mV mV mA Conditions MIN. 6.72 6.65 TYP. 7.0 MAX. 7.28 7.35 Unit V µVr.m.s. dB V A 8 µPC2900 Series ELECTRICAL CHARACTERISTICS µ PC2908 (TJ = 25 °C, VIN = 11 V, IO = 500 mA, CIN = 0.22 µF, COUT = 47 µF, unless otherwise specified.) Parameters Output Voltage Symbol VO 0 °C ≤ TJ ≤ 125 °C, 9 V ≤ VIN ≤ 18 V, 0 A ≤ IO ≤ 500 mA 0 °C ≤ TJ ≤ 125 °C, 0 A ≤ IO ≤ 1 A Line Regulation Load Regulation Quiescent Current REGIN REGL IBIAS 9 V ≤ VIN ≤ 18 V 0 A ≤ IO ≤ 1 A IO = 0 A IO = 1 A Startup Quiescent Current IBIAS (s) VIN = 7.5 V, IO = 0 A VIN = 7.5 V, IO = 1 A Quiescent Current Change Output Noise Voltage Ripple Rejection Dropout Voltage Short Circuit Current ∆IBIAS Vn R·R VDIF IO short 0 °C ≤ TJ ≤ 125 °C, 9 V ≤ VIN ≤ 18 V 10 Hz ≤ f ≤ 100 kHz f = 120 Hz, 9 V ≤ VIN ≤ 18 V 0 °C ≤ TJ ≤ 125 °C, IO = 1 A VIN = 9.5 V VIN = 18 V Peak Output Current IO peak VIN = 9.5 V VIN = 18 V Temperature Coefficient of Output Voltage ∆V O / ∆ T 0 °C ≤ TJ ≤ 125 °C, IO = 5 mA 1.1 1.4 42 2.4 145 58 0.7 1.9 1.0 1.5 2.0 0.6 3.0 2.8 mV/°C A 1.0 31 30 1.9 25 10 80 80 4.0 60 30 80 20 mA mA mV mV mA Conditions MIN. 7.68 7.6 TYP. 8.0 MAX. 8.32 8.4 Unit V µVr.m.s. dB V A 9 µPC2900 Series ELECTRICAL CHARACTERISTICS µ PC2909 (TJ = 25 °C, VIN = 12 V, IO = 500 mA, CIN = 0.22 µF, COUT = 47 µF, unless otherwise specified.) Parameters Output Voltage Symbol VO 0 °C ≤ TJ ≤ 125 °C, 10 V ≤ VIN ≤ 18 V, 0 A ≤ IO ≤ 500 mA 0 °C ≤ TJ ≤ 125 °C, 0 A ≤ IO ≤ 1 A Line Regulation Load Regulation Quiescent Current REGIN REGL IBIAS 10 V ≤ VIN ≤ 18 V 0 A ≤ IO ≤ 1 A IO = 0 A IO = 1 A Startup Quiescent Current IBIAS (s) VIN = 8.5 V, IO = 0 A VIN = 8.5 V, IO = 1 A Quiescent Current Change Output Noise Voltage Ripple Rejection Dropout Voltage Short Circuit Current ∆IBIAS Vn R·R VDIF IO short 0 °C ≤ TJ ≤ 125 °C, 10 V ≤ VIN ≤ 18 V 10 Hz ≤ f ≤ 100 kHz f = 120 Hz, 10 V ≤ VIN ≤ 18 V 0 °C ≤ TJ ≤ 125 °C, IO = 1 A VIN = 10.5 V VIN = 18 V Peak Output Current IO peak VIN = 10.5 V VIN = 18 V Temperature Coefficient of Output Voltage ∆V O / ∆ T 0 °C ≤ TJ ≤ 125 °C, IO = 5 mA 1.1 1.4 41 3.0 155 58 0.7 1.9 1.0 1.5 2.0 1.0 3.0 3.0 mV/°C A 1.0 31 32 1.9 27 11 90 90 4.0 60 30 80 20 mA mA mV mV mA Conditions MIN. 8.64 8.55 TYP. 9.0 MAX. 9.36 9.45 Unit V µVr.m.s. dB V A 10 µPC2900 Series ELECTRICAL CHARACTERISTICS µ PC2910 (TJ = 25 °C, VIN = 13 V, IO = 500 mA, CIN = 0.22 µF, COUT = 47 µF, unless otherwise specified.) Parameters Output Voltage Symbol VO 0 °C ≤ TJ ≤ 125 °C, 11 V ≤ VIN ≤ 18 V, 0 A ≤ IO ≤ 500 mA 0 °C ≤ TJ ≤ 125 °C, 0 A ≤ IO ≤ 1 A Line Regulation Load Regulation Quiescent Current REGIN REGL IBIAS 11 V ≤ VIN ≤ 18 V 0 A ≤ IO ≤ 1 A IO = 0 A IO = 1 A Startup Quiescent Current IBIAS (s) VIN = 9.5 V, IO = 0 A VIN = 9.5 V, IO = 1 A Quiescent Current Change Output Noise Voltage Ripple Rejection Dropout Voltage Short Circuit Current ∆IBIAS Vn R·R VDIF IO short 0 °C ≤ TJ ≤ 125 °C, 11 V ≤ VIN ≤ 18 V 10 Hz ≤ f ≤ 100 kHz f = 120 Hz, 11 V ≤ VIN ≤ 18 V 0 °C ≤ TJ ≤ 125 °C, IO = 1 A VIN = 11.5 V VIN = 18 V Peak Output Current IO peak VIN = 11.5 V VIN = 18 V Temperature Coefficient of Output Voltage ∆V O / ∆ T 0 °C ≤ TJ ≤ 125 °C, IO = 5 mA 1.1 1.4 40 1.9 180 56 0.7 1.7 1.0 1.6 2.0 2.1 3.0 3.0 mV/°C A 1.0 35 33 2.0 25 10 100 100 4.0 60 30 80 20 mA mA mV mV mA Conditions MIN. 9.6 9.5 TYP. 10.0 MAX. 10.4 10.5 Unit V µVr.m.s. dB V A 11 µPC2900 Series ELECTRICAL CHARACTERISTICS µ PC2912 (TJ = 25 °C, VIN = 15 V, IO = 500 mA, CIN = 0.22 µF, COUT = 47 µF, unless otherwise specified.) Parameters Output Voltage Symbol VO 0 °C ≤ TJ ≤ 125 °C, 13 V ≤ VIN ≤ 18 V, 0 A ≤ IO ≤ 500 mA 0 °C ≤ TJ ≤ 125 °C, 0 A ≤ IO ≤ 1 A Line Regulation Load Regulation Quiescent Current REGIN REGL IBIAS 13 V ≤ VIN ≤ 18 V 0 A ≤ IO ≤ 1 A IO = 0 A IO = 1 A Startup Quiescent Current IBIAS (s) VIN = 11.5 V, IO = 0 A VIN = 11.5 V, IO = 1 A Quiescent Current Change Output Noise Voltage Ripple Rejection Dropout Voltage Short Circuit Current ∆IBIAS Vn R·R VDIF IO short 0 °C ≤ TJ ≤ 125 °C, 13 V ≤ VIN ≤ 18 V 10 Hz ≤ f ≤ 100 kHz f = 120 Hz, 13 V ≤ VIN ≤ 18 V 0 °C ≤ TJ ≤ 125 °C, IO = 1 A VIN = 14 V VIN = 18 V Peak Output Current IO peak VIN = 14 V VIN = 18 V Temperature Coefficient of Output Voltage ∆V O / ∆ T 0 °C ≤ TJ ≤ 125 °C, IO = 5 mA 1.1 1.4 40 1.5 210 52 0.7 1.7 1.0 1.6 2.0 2.1 3.0 3.0 mV/°C A 1.0 38 35 2.1 26 10 120 120 4.0 60 30 80 20 mA mA mV mV mA Conditions MIN. 11.52 11.4 TYP. 12 MAX. 12.48 12.6 Unit V µVr.m.s. dB V A 12 µPC2900 Series TYPICAL CHARACTERISTICS Pd vs TA 20 Pd - Total Power Dissipation - W ∆VO - Output Voltage Deviation - mV ∆VO vs TJ 300 200 100 0 –100 –200 –300 IO = 5 mA –400 –50 15 10 Solid line : µPC2900HF Series Broken line: µPC2900HB Series W µPC2900T Series ith in fin ite he at si nk µ PC2912 µPC2905 µ PC2933 5 Without h eatsink 1.92 1.0 0 0 50 85 100 150 TA - Operating Ambient Temperature -°C VO vs VIN (µPC2933) 4.0 TJ = 25 °C 3.5 0 50 100 150 TJ - Operating Junction Temperature - °C IBIAS (IBIAS (s)) vs VIN ( µPC2933) 50 45 IBIAS - Quiescent Current - mA TJ = 25 °C IO = 1.0 A VO - Ouput Voltage - V 40 35 30 25 20 15 10 5 IO = 0 A 2 4 6 8 10 12 14 16 18 20 IO = 0.5 A IO = 1 A 3.0 2.5 IO = 0.5 A IO = 5 mA 2.0 1.5 1.0 0.5 0 1 2 3 4 5 6 7 8 0 VIN - Input Voltage - V VIN - Input Voltage - V VDIF vs TJ 1.0 IO peak - Peak Output Current - A IO peak vs VDIF (µPC2933) 3.0 µPC2933 VDIF - Dropout Voltage - V 0.8 0.6 0.4 µPC2905 µPC2906 µPC2907 µPC2908 µPC2909 µPC2910 µPC2912 IO = 1.0 A 2.0 TJ = 0 °C TJ = 25 °C 1.0 TJ = 125 °C 0.2 0 –25 0 +25 +50 +75 +100 +125 +150 0 5 10 15 20 TJ - Operating Junction Temperature - °C VDIF - Dropout Voltage - V 13 µPC2900 Series 3.0 IO peak - Peak Output Current - A IO peak vs VDIF (µPC2905) 80 70 R · R - Ripple Rejection - dB R · R vs f TJ = 25 °C IO = 1 A µ PC2933 60 50 2.0 TJ = 0 °C TJ = 25 °C 1.0 TJ = 125 °C µPC2905 40 30 20 0 µPC2912 0 5 10 15 VDIF - Dropout Voltage - V 20 10 100 1k 10 k f - Frequency - Hz 100 k 80 R · R vs IO (µPC2933) TJ = 25 °C 4.3 V ≤ VIN ≤ 16 V f = 120 Hz 1.0 VDIF vs IO (µ PC2933) TJ = 25 °C R · R - Ripple Rejection - dB 60 VDIF - Dropout Voltage - V 0.2 0.4 0.6 0.8 IO - Output Current - A 1.0 70 0.8 0.6 50 0.4 40 0.2 30 0 0 0 0.2 0.4 0.6 0.8 IO - Output Current - A 1.0 6 5 VO - Output Voltage - V 4 3 VO vs IO (µPC2933) TJ = 25 °C VIN = 16 V 2 1 VIN = 5 V 0 0.4 0.8 1.2 1.6 IO - Output Current - A 2.0 2.4 14 µPC2900 Series PACKAGE DRAWINGS µPC2900HF Series 3PIN PLASTIC SIP (MP-45G) A E B P N I L D 1 2 3 M K Y H Z C F NOTE J V U G M ITEM A B C D E F G H I J K L M N P U V Y Z MILLIMETERS 10.0 ± 0.2 7.0 ± 0.2 1.50 ± 0.2 17.0 ± 0.3 φ 3.3 ± 0.2 0.75 ± 0.10 0.25 2.54 (T.P.) 5.0 ± 0.3 2.46 ± 0.2 5.0 ± 0.2 8.5 ± 0.2 8.5 ± 0.2 4.5 ± 0.2 2.8 ± 0.2 2.4 ± 0.5 0.65 ± 0.10 8.9 ± 0.7 1.30 ± 0.2 P3HF-254B-4 Each lead centerline is located within 0.25 mm of its true position (T.P.) at maximum material condition. 15 µPC2900 Series µPC2900HB Series MP-3 (SC-64) (Unit: mm) 1.5 +0.2 –0.1 6.5±0.2 5.0±0.2 4 2.3±0.2 0.5±0.1 1.6±0.2 1.1±0.1 0.5 +0.2 –0.1 2.3 2.3 7.0 MIN. 13.7 MIN. 1 2 3 5.5±0.2 0.5 +0.2 –0.1 µPC2900T Series MP-3Z (SC-63) (Unit: mm) 6.5±0.2 5.0±0.2 2.3±0.2 1.5 +0.2 –0.1 0.75 0.5±0.1 4 4.3 MAX. 5.5±0.2 10.0 MAX. 1 2 3 2.0 MIN. 0.8 0.9 MAX. 2.3 2.3 0.8 MAX. 0.8 16 0.5 1.1±0.2 1.0 MIN. 1.5 TYP. µPC2900 Series RECOMMENDED SOLDERING CONDITIONS When soldering this product, it is highly recommended to observe the conditions as shown below. If other soldering processes are used, or if the soldering is perfomed under different condition, please make sure to consult with our sales offices. Fof more details, refer to our document “SEMICONDUCTOR DEVICE MOUNTING TECHNOLOGY MANUAL” (C10535E). Surface mount devices µPC2900T Series: MP-3Z Process Infrared ray reflow Conditions Peak temperature: 235 °C or below (Package surface temperature), Reflow time: 30 seconds or less (at 210 °C or higher), Maximum number of reflow processes: 2 times. Peak temperature: 215 °C or below (Package surface temperature), Reflow time: 40 seconds or less (at 200 °C or higher), Maximum number of reflow processes: 2 times. Solder temperature: 260 °C or below, Flow time: 10 seconds or less, Maximum number of flow processes: 1 time, Pre-heating temperature: 120 °C or below (Package surface temperature). Pin temperature: 300 °C or below, Heat time: 3 seconds or less (Per each side of the device). Symbol IR35-00-2 VPS VP15-00-2 Wave soldering WS60-00-1 Partial heating method — Caution Apply only one kind of soldering condition to a device, except for “partial heating method”, or the device will be damaged by heat stress. Through-hole devices µPC2900HF Series: MP-45G µPC2900HB Series: MP-3 Process Wave soldering (only to leads) Partial heating method Conditions Solder temperature: 260 °C or below, Flow time: 10 seconds or less. Pin temperature: 300 °C or below, Heat time: 3 seconds or less (Per each pin). Caution For through-hole device, the wave soldering process must be applied only to leads, and make sure that the package body does not get jet soldered. 17 µPC2900 Series CAUTION ON USE When using the µPC2900 series at the input voltage which is lower than in the recommended operating condition, the big quiescent current flows through devices because the transistor of the output paragraph is saturated (Refer to IBIAS (IBIAS (s)) vs VIN curves in TYPICAL CHARACTERISTICS). The µPC2900 series have saturation protection circuits, but they sometimes need about 80 mA current. Therefore the power supply on the input needs the enough current capacity to pass this quiescent current when the devices startup. REFERENCE DOCUMENTS QUALITY GRADE ON NEC SEMICONDUCTOR DEVICES SEMICONDUCTOR DEVICE MOUNTING TECHNOLOGY MANUAL IC PACKAGE MANUAL GUIDE TO QUALITY ASSUARANCE FOR SEMICONDUCTOR DEVICES SEMICONDUCTORS SELECTION GUIDE NEC SEMICONDUCTOR DEVICE RELIABILITY/QUALITY CONTROL SYSTEM-THREE TERMINAL REGULATOR C11531E C10535E C10943X MEI-1202 X10679E IEI-1212 18 µPC2900 Series [MEMO] 19 µPC2900 Series [MEMO] No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. NEC devices are classified into the following three quality grades: "Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific application. The recommended applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance. Anti-radioactive design is not implemented in this product. M4 96.5 20