UPC574J

DATA SHEET BIPOLAR ANALOG INTEGRATED CIRCUIT µPC574 MONOLITHIC BIPOLAR INTEGRATED CIRCUIT VOLTAGE STABILIZER FOR ELECTRONIC TUNER The µPC574 is a monolithic integrated voltage stabilizer especially designed as voltage supplier for electronic tuners. FEATURES • Low temperature coefficient • Low dynamic resistance • Typical reference voltage of 33 V EQUIVALENT CIRCUIT 2 R4 PIN CONFIGURATION (Marking Side) µPC574J: 2-pin plastic SIP (TO-92) D1 D2 D3 D4 D5 Q3 R3 Q2 Q1 R2 R1 1 1 1. Anode 2. Cathode 2 ORDERING INFORMATION Part Number Package 2-pin plastic SIP (TO-92) µPC574J The information in this document is subject to change without notice. Document No. S13200EJ4V0DS00 (4th edition) (Previous No. IC-1006) Date Published January 1998 N CP(K) Printed in Japan The mark shows major revised points. © 1998 µPC574 ABSOLUTE MAXIMUM RATINGS (TA = 25°C, unless otherwise specified.) Parameter Zener Current Power Dissipation Operating Ambient Temperature Range Storage Temperature Range Symbol IZ PD TA Tstg Ratings 10 200 (TA = 75°C) –20 to +75 –40 to +125 Unit mA mW °C °C Caution Exposure to Absolute Maximum Ratings for extended periods may affect device reliability; exceeding the ratings could cause permanent damage. The parameters apply independently. The device should be operated within the limits specified under DC and AC Characteristics. ELECTRICAL CHARACTERISTICS (TA = 25°C, unless otherwise specified.) Parameter Stabilized Voltage Stabilized Voltage Temperature Drift Dynamic Resistance Symbol VZ I Z = 5 mA IZ = 5 mA, TA = –20 to +75°C Conditions MIN. 31 –1.0 0 TYP. MAX. 35 +1.0 Unit V mV/°C Ω ∆VZ/∆T rZ IZ = 5 mA, f = 1 kHz, IAC = 0.5 mA 10 25 2 µPC574 TYPICAL CHARACTERISTIC (TA = 25°C, unless otherwise specified.) Power Dissipation vs. Ambient Temperature 80 60 Dynamic Resistance vs. Zener Current Free Air PD - Power Dissipation - mW 400 rZ - Dynamic Resistance - Ω 40 IAC = IZ 10 f = 1 kHz 300 20 200 10 8 6 4 100 2 –20 0 25 50 75 TA - Operating Ambient Temperature - °C 0 2 4 6 8 IZ - Zener Current - mA 10 ∆VZ/ ∆ T - Stabilized Voltage Temperature Drift - mV/°C Stabilized Voltage Temperature Drift vs. Zener Current Stabilized Voltage Variation vs. Time +4 +3 +2 +1 0 –1 –2 –3 –4 0 2 4 6 8 IZ - Zener Current - mA 10 ∆ VZ - Stabilized Voltage Variation - mV +80 +60 +40 +20 0 –20 –40 –60 –80 0 5 10 15 20304050 1 s. t - Time 5 10 20 30 min. IZ = 5 mA XY – Recoder Free Air IZ = 5 mA +– VZ = 33.11 V VREF ( ∆ VZ/VZ) × 100 - Stabilized Voltage Variation - % Stabilized Voltage Variation & Supply Voltage Variation vs. Zener Current +1.0 +0.2 0 –0.2 –0.4 –0.6 –0.8 –1.0 0 2 = 1 10 +0.4 VB V 574J VZ kΩ 2 RS +0.6 =2 RS A IZ +30 +20 +10 0 –10 ∆VZ = VZ (IZ) – VZ (5) –20 TA = –20 °C TA = +25 °C –30 TA = +75 °C 4 6 8 IZ - Zener Current - mA 10 ∆VB - Supply Voltage Variation - V +0.8 R S 0k Ω Reference IZ = 5 mA 3 µPC574 MEASURING CIRCUITS (i) Measuring Circuit for Stabilized Voltage VZ IZ = 5 mA A 2 RB µ PC574 EB 1 V Digital Volt Meter (ii) Measuring Circuit for Dynamic Resistance rZ IZ 10 IZ A 2 C 0.1 µF EB 1 + 50 µF RB IAC = 100 Ω VV2 VV1 µ PC574 f = 1 kHz VZ IZ 0.5 mA 5 mA rZ = VV1 0.5 mA VV1 4 µPC574 TYPICAL APPLICATION Ri Ach Bch Ych Zch 2 Vi µ PC574 1 C 15 kΩ 15 kΩ 15 kΩ 15 kΩ Channel setting Variable resistor to tuning diodes (VARACTOR) in case of Ych ON 5 µPC574 PACKAGE DRAWING 2 PIN PLASTIC SIP (TO-92) A N M Q 1 2 K Y H F G J M V U NOTE Each lead centerline is located within 0.25 mm (0.01 inch) of its true position (T.P.) at maximum material condition. ITEM A F G H J K M N Q U V Y MILLIMETERS 5.2 MAX. 0.5±0.1 0.25 2.54 1.33 MAX. 1.8 MIN. 5.5 MAX. 4.2 MAX. 8.0 MAX. 2.8 MAX. 0.5±0.1 15.0±0.7 INCHES 0.205 MAX. 0.02 +0.004 –0.005 0.01 0.1 0.053 MAX. 0.07 MIN. 0.217 MAX. 0.166 MAX. 0.315 MAX. 0.111 MAX. 0.02 +0.004 –0.005 0.591 +0.028 –0.029 P2J-254B-1 6 µPC574 RECOMMENDED SOLDERING CONDITIONS When soldering this product, it is highly recommended to observe the conditions as shown below. If other soldering processes are used, or if the soldering is performed under different conditions, please make sure to consult with our sales offices. For more details, refer to our document “SEMICONDUCTOR DEVICE MOUNTING TECHNOLOGY MANUAL” (C10535E). Through-hole device µPC574J: 2-pin plastic SIP (TO-92) Process Wave soldering (only to leads) Partial heating method Solder temperature: 260°C or below, Flow time: 10 seconds or less. Pin temperature: 300°C or below, Heat time: 3 seconds or less (per each lead.) Conditions Caution For through-hole device, the wave soldering process must be applied only to leads, and make sure that the package body does not get jet soldered. 7 µPC574 [MEMO] The application circuits and their parameters are for reference only and are not intended for use in actual design-ins. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. NEC devices are classified into the following three quality grades: "Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific application. The recommended applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance. Anti-radioactive design is not implemented in this product. M4 96.5