UPD43256BGU-70L

DATA SHEET MOS INTEGRATED CIRCUIT µPD43256B 256K-BIT CMOS STATIC RAM 32K-WORD BY 8-BIT Description The µPD43256B is a high speed, low power, and 262, 144 bits (32,768 words by 8 bits) CMOS static RAM. Battery backup is available (L, LL, A, and B versions). And A and B versions are wide voltage operations. The µPD43256B is packed in 28-pin plastic DIP, 28-pin plastic SOP and 28-pin plastic TSOP (I). Features • 32,768 words by 8 bits organization • Fast access time: 70, 85, 100, 120, 150 ns (MAX.) • Wide voltage range (A version: VCC = 3.0 to 5.5 V, B version: VCC = 2.7 to 5.5 V) • 2 V data retention • OE input for easy application Operating supply voltage V 4.5 to 5.5 Operating temperature °C 0 to 70 Standby supply current µA (MAX.) 50 15 3.0 to 5.5 2.7 to 5.5 Data retention supply currentNote 1 µA (MAX.) 3 2 Part number Access time ns (MAX.) 70, 85 70, 85 85, 100Note 2, 120Note 2 µPD43256B-L µPD43256B-LL µPD43256B-A µPD43256B-BNote 2 100, 120, 150 Notes 1. TA ≤ 40 ˚C, VCC = 3 V 2. Access time : 85 ns (MAX.) (VCC = 4.5 to 5.5 V) Version X and P This data sheet can be applied to the version X and P. Each version is identified with its lot number. Letter X in the fifth character position in a lot number signifies version X, letter P, version P. JAPAN D43256B Lot number The information in this document is subject to change without notice. Document No. M10770EJ9V0DS00 (9th edition) Date Published May 1997 N Printed in Japan The mark shows major revised points. © 1990, 1993, 1994 µPD43256B Ordering Information Operating supply voltage V 4.5 to 5.5 Operating temperature ˚C 0 to 70 Part number Package Access time ns (MAX.) 70 85 70 85 Remark µ PD43256BCZ-70L µ PD43256BCZ-85L µ PD43256BCZ-70LL µ PD43256BCZ-85LL µ PD43256BGU-70L µ PD43256BGU-85L µ PD43256BGU-70LL µ PD43256BGU-85LL µ PD43256BGU-A85 µ PD43256BGU-A10 µ PD43256BGU-A12 µ PD43256BGU-B10 µ PD43256BGU-B12 µ PD43256BGU-B15 µ PD43256BGW-70LL-9JL µ PD43256BGW-85LL-9JL µ PD43256BGW-A85-9JL µ PD43256BGW-A10-9JL µ PD43256BGW-A12-9JL µ PD43256BGW-B10-9JL µ PD43256BGW-B12-9JL µ PD43256BGW-B15-9JL µ PD43256BGW-70LL-9KL µ PD43256BGW-85LL-9KL µ PD43256BGW-A85-9KL µ PD43256BGW-A10-9KL µ PD43256BGW-A12-9KL µ PD43256BGW-B10-9KL µ PD43256BGW-B12-9KL µ PD43256BGW-B15-9KL 28-pin plastic DIP (600 mil) L Version LL Version 28-pin plastic SOP (450 mil) 70 85 70 85 85 100 120 100 120 150 2.7 to 5.5 3.0 to 5.5 L Version LL Version A Version B Version 28-pin plastic TSOP (I) (8 × 1 3.4 mm) (Normal bent) 70 85 85 100 120 100 120 150 4.5 to 5.5 LL Version 3.0 to 5.5 A Version 2.7 to 5.5 B Version 28-pin plastic TSOP (I) (8 × 1 3.4 mm) (Reverse bent) 70 85 85 100 120 100 120 150 4.5 to 5.5 LL Version 3.0 to 5.5 A Version 2.7 to 5.5 B Version 2 µPD43256B Pin Configuration (Marking Side) 28-pin plastic DIP (600 mil) µ PD43256BCZ 28-pin plastic SOP (450 mil) µ PD43256BGU A14 A12 A7 A6 A5 A4 A3 A2 A1 A0 I/O1 I/O2 I/O3 GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 VCC WE A13 A8 A9 A11 OE A10 CS I/O8 I/O7 I/O6 I/O5 I/O4 A0 - A14 CS WE OE V CC GND : Address inputs : Chip Select : Write Enable : Output Enable : Power supply : Ground I/O1 - I/O8 : Data inputs/outputs 3 µPD43256B 28-pin plastic TSOP (I) (8 × 13.4 mm) (Normal bent) µ PD43256BGW-9JL OE A11 A9 A8 A13 WE VCC A14 A12 A7 A6 A5 A4 A3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 A10 CS I/O8 I/O7 I/O6 I/O5 I/O4 GND I/O3 I/O2 I/O1 A0 A1 A2 28-pin plastic TSOP (I) (8 × 13.4 mm) (Reverse bent) µ PD43256BGW-9KL A10 CS I/O8 I/O7 I/O6 I/O5 I/O4 GND I/O3 I/O2 I/O1 A0 A1 A2 28 27 26 25 24 23 22 21 20 19 18 17 16 15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 OE A11 A9 A8 A13 WE VCC A14 A12 A7 A6 A5 A4 A3 4 µPD43256B Block Diagram Address buffer A0 | A14 Row decoder Memory cell array 262,144 bits I/O1 | I/O8 Input data controller Sense/Switch Output data controller Column decoder Address buffer CS OE WE VCC GND Truth Table CS H L L L OE × H × L WE × H L H Mode Not selected Output disable Write Read D IN D OUT I/O High impedance Supply current I SB I CCA Remark × : Don’t care 5 µPD43256B Electrical Characteristics Absolute Maximum Ratings Parameter Supply voltage Input/Output voltage Operating ambient temperature Storage temperature Symbol V CC VT TA T stg Rating –0.5 Note t o +7.0 –0.5 Note t o V CC + 0 .5 0 to 70 –55 to +125 Unit V V ˚C ˚C Note – 3.0 V (MIN.) (Pulse width 50 ns) Caution Exposing the device to stress above those listed in absolute maximum ratings could cause permanent damage. The device is not meant to be operated under conditions outside the limits described in the operational sections of this characteristics. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Recommended Operating Conditions µ PD43256B-L µ PD43256B-LL MIN. Supply voltage High level input voltage Low level input voltage Operating ambient temperature V CC V IH V IL TA 4.5 2.2 –0.3 Note 0 MAX. 5.5 V CC + 0 .5 +0.8 70 µ PD43256B-A MIN. 3.0 2.2 –0.3 Note 0 MAX. 5.5 V CC + 0 .5 +0.5 70 µ PD43256B-B Unit MIN. 2.7 2.2 –0.3 Note 0 MAX. 5.5 V CC + 0 .5 +0.5 70 V V V ˚C Parameter Symbol Note – 3.0 V (MIN.) (Pulse width 50 ns) 6 µPD43256B DC Characteristics (Recommended operating conditions unless otherwise noted) (1/2) µ PD43256B-L Parameter Input leakage current I/O leakage current Symbol I LI I LO Test conditions V IN = 0 V t o VCC V I/O = 0 V t o V CC OE = V IH o r CS = V IH o r WE = V IL CS = V IL, Minimum cycle time, I I/O = 0 m A CS = V IL, I I/O = 0 m A CS ≤ 0 .2 V, Cycle = 1 MHz, I I/O = 0 m A V IL ≤ 0 .2 V, V IH ≥ V CC – 0 .2 V CS = V IH CS ≥ V CC – 0 .2 V I OH = – 1.0 mA I OH = – 0.1 mA I OL = 2 .1 mA 2.4 V CC–0.5 0.4 1.0 µ PD43256B-LL Unit MIN. TYP. MAX. MIN. TYP. MAX. –1.0 –1.0 +1.0 –1.0 +1.0 –1.0 +1.0 +1.0 µA µA mA Operating supply current I CCA1 45 45 I CCA2 I CCA3 10 10 10 10 Standby supply current I SB I SB1 3 50 2.4 V CC–0.5 0.5 3 15 mA µA V High level output voltage V OH1 V OH2 Low level output voltage V OL 0.4 V Remarks 1. V IN: Input voltage 2. These DC Characteristics are in common regardless of package types. 7 µPD43256B DC Characteristics (Recommended operating conditions unless otherwise noted) (2/2) µ PD43256B-A Parameter Input leakage current I/O leakage current Symbol I LI I LO Test conditions V IN = 0 V t o VCC V I/O = 0 V t o V CC CS = V IH o r WE = V IL o r OE = V IH CS = V IL, µ PD43256B-A85 Minimum cycle time, µ PD43256B-A10 I I/O = 0 m A µ PD43256B-A12 µ PD43256B-B Unit MIN. TYP. MAX. MIN. TYP. MAX. –1.0 –1.0 +1.0 –1.0 +1.0 –1.0 +1.0 +1.0 µA µA mA Operating supply current I CCA1 45 — µ PD43256B-B10 µ PD43256B-B12 µ PD43256B-B15 V CC ≤ 3 .3 V I CCA2 CS = V IL, I I/O = 0 m A V CC ≤ 3 .3 V I CCA3 CS ≤ 0 .2 V, Cycle = 1 MHz, I I/O = 0 m A, V IL ≤ 0 .2 V, V IH ≥ V CC – 0 .2 V Standby supply current I SB CS = V IH V CC ≤ 3 .3 V I SB1 CS ≥ V CC – 0 .2 V V CC ≤ 3 .3 V High level output voltage V OH1 I OH = – 1.0 mA, VCC ≥ 4 .5 V I OH = – 0.5 mA, V CC < 4 .5 V V OH2 I OH = – 0.1 mA I OH = – 0.02 mA Low level output voltage V OL I OL = 2 .1 mA, V CC ≥ 4 .5 V I OL = 1 .0 mA, V CC < 4 .5 V V OL1 I OL = 0 .02 mA 2.4 2.4 — VCC –0.1 0.5 V CC ≤ 3 .3 V — 45 — 10 — 10 20 10 5 10 — 3 — 15 — 2.4 2.4 — VCC –0.1 0.4 0.4 0.1 0.5 0.5 5 3 2 15 10 V mA µA 0.4 0.4 0.1 V Remarks 1. V IN: Input voltage 2. These DC characteristics are in common regardless of package types. Capacitance (T A = 2 5 ˚C, f = 1 MHz) Parameter Input capacitance Input/Output capacitance Symbol CIN CI/O V IN = 0 V V I/O = 0 V Test conditions MIN. TYP. MAX. 5 8 Unit pF pF Remarks 1. V IN: Input voltage 2. These parameters are periodically sampled and not 100 % tested. 8 µPD43256B AC Characteristics (Recommended operating conditions unless otherwise noted) AC Test Conditions Input waveform (Rise/fall time ≤ 5 n s) Input pulse levels 0.8 V to 2.2 V: µ PD43256B-L, 43256B-LL 0.5 V to 2.2 V: µ PD43256B-A, 43256B-B 1.5 V Test points 1.5 V Output waveform 1.5 V Test points 1.5 V Output load µ PD43256B-A, 43256B-B : 1TTL + 100 pF µ PD43256B-L, 43256B-LL: AC characteristics with notes should be measured with the output load shown in Figure 1 a nd F igure 2 . Figure 1 (For t AA, tACS , t OE, t OH) +5 V Figure 2 (For t CHZ, t CLZ , t OHZ, t OLZ , t WHZ, t OW ) +5 V 1.8 kΩ 1.8 kΩ I/O (Output) I/O (Output) 990 Ω 100 pF CL 990 Ω 5 pF CL R emark C L i ncludes capacitances of the probe and jig, and stray capacitances. 9 µPD43256B Read Cycle (1/2) V CC ≥ 4 .5 V Parameter Symbol µ PD43256B-70 MIN. MAX. µ PD43256B-85 µ PD43256B-A85/A10/A12 µ PD43256B-B10/B12/B15 MIN. 85 MAX. Unit Condition Read cycle time Address access time CS access time OE access time Output hold from address change CS to output in low impedance OE to output in low impedance CS to output in high impedance OE to output in high impedance t RC t AA t ACS t OE t OH t CLZ t OLZ t CHZ t OHZ 70 70 70 35 10 10 5 30 30 ns 85 85 40 ns ns ns ns ns ns 30 30 ns ns Note 2 Note 1 10 10 5 Notes 1. See the output load shown in F igure 1 e xcept for µ PD43256B-A, 43256B-B. 2. See the output load shown in F igure 2 e xcept for µ PD43256B-A, 43256B-B. Remark T hese AC characteristics are in common regardless of package types and L, LL versions. Read Cycle (2/2) V CC ≥ 3 .0 V Parameter V CC ≥ 2 .7 V Symbol µ PD43256B-A85 µ PD43256B-A10 µ PD43256B-A12 µ PD43256B-B10 µ PD43256B-B12 µ PD43256B-B15 Unit MIN. MAX. MIN. MAX. MIN. MAX. MIN. MAX. MIN. MAX. MIN. MAX. Condition Read cycle time Address access time CS access time OE access time Output hold from address change CS to output in low impedance OE to output in low impedance CS to output in high impedance OE to output in high impedance t RC t AA t ACS t OE tOH tCLZ tOLZ tCHZ tOHZ 85 85 85 50 10 10 5 35 35 100 100 100 60 10 10 5 35 35 120 120 120 60 10 10 5 40 40 100 100 100 60 10 10 5 35 35 120 120 120 60 10 10 5 40 40 150 ns 150 ns Note 150 ns 70 ns ns ns ns 50 50 ns ns 10 10 5 Note L oading condition is 1TTL + 100 pF. Remark T hese AC characteristics are in common regardless of package types and L, LL versions. 10 µPD43256B Read Cycle Timing Chart tRC Address (Input) tAA tACS CS (Input) tCLZ OE (Input) tOE tOLZ I/O (Output) High impedance Data out High impedance tOHZ tCHZ tOH Remark I n read cycle, WE should be fixed to high level. 11 µPD43256B Write Cycle (1/2) V CC ≥ 4 .5 V Parameter Symbol µ PD43256B-70 MIN. MAX. µ PD43256B-85 µ PD43256B-A85/A10/A12 µ PD43256B-B10/B12/B15 MIN. 85 70 70 60 35 0 0 0 MAX. Unit Condition Write cycle time CS to end of write Address valid to end of write Write pulse width Data valid to end of write Data hold time Address setup time Write recovery time WE to output in high impedance Output active from end of write t WC t CW t AW t WP t DW t DH t AS t WR t WHZ t OW 70 50 50 55 30 0 0 0 30 10 ns ns ns ns ns ns ns ns 30 ns ns Note 10 Note S ee the output load shown in F igure 2 e xcept for µ PD43256B-A, 43256B-B. Remark T hese AC characteristics are in common regardless of package types and L, LL versions. Write Cycle (2/2) V CC ≥ 3 .0 V Parameter V CC ≥ 2 .7 V Condition Symbol µ PD43256B-A85 µ PD43256B-A10 µ PD43256B-A12 µ PD43256B-B10 µ PD43256B-B12 µ PD43256B-B15 Unit MIN. MAX. MIN. MAX. MIN. MAX. MIN. MAX. MIN. MAX. MIN. MAX. Write cycle time CS to end of write Address valid to end of write Write pulse width Data valid to end of write Data hold time Address setup time Write recovery time WE to output in high impedance Output active from end of write t WC t CW t AW t WP t DW t DH t AS t WR tWHZ t OW 85 70 70 60 60 0 0 0 30 10 100 70 70 60 60 0 0 0 35 10 120 90 90 80 70 0 0 0 40 10 100 70 70 60 60 0 0 0 35 10 120 90 90 80 70 0 0 0 40 10 150 100 100 90 80 0 0 0 50 10 ns ns ns ns ns ns ns ns ns Note ns Note L oading condition is 1TTL + 100 pF. Remark T hese AC characteristics are in common regardless of package types and L, LL versions. 12 µPD43256B Write Cycle Timing Chart 1 (WE Controlled) tWC Address (Input) tCW CS (Input) tAW tAS WE (Input) tOW tWHZ I/O (Input/Output) Indefinite data out High impedance tDW Data in tDH High impedance Indefinite data out tWP tWR Cautions 1. CS or WE should be fixed to high level during address transition. 2. When I/O pins are in the output state, do not apply to the I/O pins signals that are opposite in phase with output signals. Remarks 1. Write operation is done during the overlap time of a low level CS and a low level WE. 2. When WE is at low level, the I/O pins are always high impedance. When WE is at high level, read operation is executed. Therefore OE should be at high level to make the I/O pins high impedance. 3. If CS changes to low level at the same time or after the change of WE to low level, the I/O pins will remain high impedance state. 13 µPD43256B Write Cycle Timing Chart 2 (CS Controlled) tWC Address (Input) tAS CS (Input) tAW tWP WE (Input) tCW tWR tDW High impedance I/O (Input) Data In tDH High impedance Cautions 1. CS or WE should be fixed to high level during address transition. 2. When I/O pins are in the output state, do not apply to the I/O pins signals that are opposite in phase with output signals. Remark W rite operation is done during the overlap time of a low level CS and a low level WE. 14 µPD43256B Low V CC D ata Retention Characteristics L Version ( µ PD43256B-L: T A = 0 t o 70 ˚C) Parameter Symbol Test conditions CS ≥ V CC – 0 .2 V V CC = 3 .0 V, CS ≥ V CC – 0 .2 V 0 MIN. 2.0 0.5 TYP. MAX. 5.5 20 Note Unit V Data retention supply voltage V CCDR Data retention supply current Chip deselection to data retention mode Operation recovery time I CCDR t CDR µA ns tR 5 ms Note 3 µ A (T A ≤ 4 0 ˚C) LL Version ( µ PD43256B-LL: T A = 0 t o 70 ˚C) A Version ( µ PD43256B-A: T A = 0 t o 70 ˚C) B Version ( µ PD43256B-B: T A = 0 t o 70 ˚C) Parameter Data retention supply voltage Data retention supply current Chip deselection to data retention mode Operation recovery time Symbol V CCDR I CCDR t CDR Test conditions CS ≥ V CC – 0 .2 V V CC = 3 .0 V, CS ≥ V CC – 0 .2 V 0 MIN. 2.0 0.5 TYP. MAX. 5.5 7 Note Unit V µA ns tR 5 ms Note 2 µ A (T A ≤ 4 0 ˚C), 1 µ A (T A ≤ 2 5 ˚C) 15 µPD43256B Data Retention Timing Chart tCDR 5.0 V 4.5 V Note Data retention mode tR VCC CS VIH (MIN.) VCCDR CS ≥ VCC – 0.2 V VIL (MAX.) GND Note A V ersion: 3.0 V, B Version: 2.7 V Remark T he other pins (address, OE, WE, I/Os) can be in high impedance state. 16 µPD43256B Package Drawings 28 PIN PLASTIC DIP (600 mil) 28 15 1 A 14 K L J I G H F D N M C B M R NOTES 1) Each lead centerline is located within 0.25 mm (0.01 inch) of its true position (T.P.) at maximum material condition. 2) Item "K" to center of leads when formed parallel. ITEM MILLIMETERS A B C D F G H I J K L M N R 38.10 MAX. 2.54 MAX. 2.54 (T.P.) 0.50±0.10 1.2 MIN. 3.6±0.3 0.51 MIN. 4.31 MAX. 5.72 MAX. 15.24 (T.P.) 13.2 0.25 +0.10 –0.05 0.25 0 ~ 15 ° INCHES 1.500 MAX. 0.100 MAX. 0.100 (T.P.) +0.004 0.020 –0.005 0.047 MIN. 0.142±0.012 0.020 MIN. 0.170 MAX. 0.226 MAX. 0.600 (T.P.) 0.520 0.010 +0.004 –0.003 0.01 0 ~ 15 ° P28C-100-600A1-1 17 µPD43256B 28 PIN PLASTIC SOP (450 mil) 28 15 detail of lead end 1 A G 14 H I J F E C D M M N B K L NOTE Each lead centerline is located within 0.12 mm (0.005 inch) of its true position (T.P.) at maximum material condition. ITEM MILLIMETERS A B C D E F G H I J K L M N P 19.05 MAX. 1.27 MAX. 1.27 (T.P.) 0.40±0.10 0.2±0.1 3.0 MAX. 2.55±0.1 11.8±0.3 8.4±0.1 1.7±0.2 0.20 +0.07 –0.03 0.7±0.2 0.12 0.10 5°±5° P INCHES 0.750 MAX. 0.050 MAX. 0.050 (T.P.) 0.016 +0.004 –0.005 0.008±0.004 0.119 MAX. 0.100 +0.005 –0.004 0.465 +0.012 –0.013 0.331 +0.004 –0.005 0.067±0.008 0.008 +0.003 –0.002 0.028 +0.008 –0.009 0.005 0.004 5°±5° P28GU-50-450A-1 18 µPD43256B 28PIN PLASTIC TSOP ( I ) (8×13.4) 1 28 detail of lead end S R 14 15 Q P I J A G H L K NOTE (1) Each lead centerline is located within 0.08 mm (0.003 inch) of its true position (T.P.) at maximum material condition. (2) "A" excludes mold flash. (Includes mold flash : 8.4mm MAX. ) C N D M M B ITEM MILLIMETERS A 8.0±0.1 B C D G H I J K L M N P Q R S 0.6 MAX. 0.55 (T.P.) 0.22 +0.08 –0.07 1.0 12.4±0.2 11.8±0.1 0.8±0.2 INCHES 0.315±0.004 0.024 MAX. 0.022 (T.P.) 0.009±0.003 0.039 0.488±0.008 0.465 +0.004 –0.005 0.031 +0.009 –0.008 0.145 +0.025 0.006±0.001 –0.015 0.5±0.1 0.08 0.10 13.4±0.2 0.1±0.05 3 ° +7 ° –3 ° 1.2 MAX. 0.020 +0.004 –0.005 0.003 0.004 0.528 +0.008 –0.009 0.004±0.002 3 ° +7 ° –3 ° 0.048 MAX. P28GW-55-9JL-1 19 µPD43256B 28PIN PLASTIC TSOP ( I ) (8×13.4) 1 28 detail of lead end Q R S 14 15 K H N L D M M C B G I P J A NOTE (1) Each lead centerline is located within 0.08 mm (0.003 inch) of its true position (T.P.) at maximum material condition. (2) "A" excludes mold flash. (Includes mold flash : 8.4mm MAX. ) ITEM MILLIMETERS A 8.0±0.1 B C D G H I J K L M N P Q R S 0.6 MAX. 0.55 (T.P.) 0.22 +0.08 –0.07 1.0 12.4±0.2 11.8±0.1 0.8±0.2 INCHES 0.315±0.004 0.024 MAX. 0.022 (T.P.) 0.009±0.003 0.039 0.488±0.008 0.465 +0.004 –0.005 0.031 +0.009 –0.008 0.145 +0.025 0.006±0.001 –0.015 0.5±0.1 0.08 0.10 13.4±0.2 0.1±0.05 3 ° +7 ° –3 ° 1.2 MAX. 0.020 +0.004 –0.005 0.003 0.004 0.528 +0.008 –0.009 0.004±0.002 3 ° +7 ° –3 ° 0.048 MAX. P28GW-55-9KL-1 20 µPD43256B Recommended Soldering Conditions The following conditions (See table below) must be met when soldering µ PD43256B. For more details, refer to our document “ SEMICONDUCTOR DEVICE MOUNTING TECHNOLOGY MANUAL” ( C10535E) . Please consult with our sales offices in case other soldering process is used, or in case soldering is done under different conditions. Types of Surface Mount Device µ PD43256BGU: 28-pin plastic SOP (450 mil) µ PD43256BGW-9JL: 28-pin plastic TSOP (I) (8 × 1 3.4 mm) (Normal bent) µ PD43256BGW-9KL: 28-pin plastic TSOP (I) (8 × 1 3.4 mm) (Reverse bent) Please consult with our sales offices. Type of Through Hole Mount Device µ PD43256BCZ: 28-pin plastic DIP (600 mil) Soldering process Wave soldering (only to leads) Partial heating method Soldering conditions Solder temperature: 260 ˚C or below, Flow time: 10 seconds or below Terminal temperature: 300 ˚C or below, Time: 3 seconds or below (Per one lead) Caution Do not jet molten solder on the surface of package. 21 µPD43256B [MEMO] 22 µPD43256B NOTES FOR CMOS DEVICES 1 PRECAUTION AGAINST ESD FOR SEMICONDUCTORS Note: Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and ultimately degrade the device operation. Steps must be taken to stop generation of static electricity as much as possible, and quickly dissipate it once, when it has occurred. Environmental control must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using insulators that easily build static electricity. Semiconductor devices must be stored and transported in an anti-static container, static shielding bag or conductive material. All test and measurement tools including work bench and floor should be grounded. The operator should be grounded using wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need to be taken for PW boards with semiconductor devices on it. 2 HANDLING OF UNUSED INPUT PINS FOR CMOS Note: No connection for CMOS device inputs can be cause of malfunction. If no connection is provided to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence causing malfunction. CMOS device behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected to VDD o r GND with a resistor, if it is considered to have a possibility of being an output pin. All handling related to the unused pins must be judged device by device and related specifications governing the devices. 3 STATUS BEFORE INITIALIZATION OF MOS DEVICES Note: Power-on does not necessarily define initial status of MOS device. Production process of MOS does not define the initial operation status of the device. Immediately after the power source is turned ON, the devices with reset function have not yet been initialized. Hence, power-on does not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the reset signal is received. Reset operation must be executed immediately after power-on for devices having reset function. 23 µPD43256B [MEMO] No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. NEC devices are classified into the following three quality grades: "Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific application. The recommended applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance. Anti-radioactive design is not implemented in this product. M4 96.5 2