UPD4990AG

DATA SHEET MOS INTEGRATED CIRCUIT µPD4990A SERIAL I/O CALENDAR & CLOCK CMOS LSI The µPD4990A is a CMOS LSI developed to input/output calendar & clock data serially to/from the micro computer. The crystal frequency is 32.768 kHz and the data items included are time, minute, second, year, month, day, and week. FEATURES • • • • • Built-in counters for time (hour, minute, and second) and date (year, month, day, and week) Leap years are adjusted automatically. Data is represented in BCD notation (except months in hexadecimal notation) and input/output serially. Commands can be set by inputting serial data. Selective timing pulses (TPs) are 64 Hz, 256 Hz, 2 048 Hz, and 4 096 Hz and selective output intervals are 1, 10, 30, and 60 seconds. ORDERING INFORMATION PART No. PACKAGE 14-pin plastic DIP (300 mil) 16-pin plastic SOP (300 mil) µPD4990AC µPD4990AG CONNECTION DIAGRAM (Top View) C2 C1 C0 STB CS DATA IN GND (VSS) 1 2 3 4 5 6 7 14 13 12 11 10 9 8 VDD (+) XTAL XTAL OUT ENBL TP DATA OUT CLK C2 C1 C0 NC STB CS DATA IN GND (VSS) 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 VDD (+) XTAL XTAL NC OUT ENBL TP DATA OUT CLK µ PD4990AC µ PD4990AG NC: NO CONNECTION Document No. IC-1755 (1st edition) Date Published March 1997 P Printed in Japan © 1989 µPD4990A ABSOLUTE MAXIMUM RATINGS Supply Voltage Input Voltage Operating Temperature Range Storage Temperature Range Output Terminal Voltage VDD − VSS VIN Topt Tstg VOUT −0.5 to 7.0 VSS −0.3 to VDD +0.3 − 40 to +85 −65 to +125 −0.5 to 7.0 V V °C °C V ELECTRICAL CHARACTERISTICS (f = 32.768 kHz, CG = CD = 20 pF, CI = 20 kΩ, Ta = 25 °C) CHARACTERISTIC Operating Voltage Current Consumption SYMBOL VDD − VSS IDD 100 Low Level Output Voltage CLK Input Frequency Input Leakage Current High Level Input Voltage Low Level Input Voltage VOL fCLK IIN VIH VIL 0.7 VDD VSS DC 0.4* 500 ±1 VDD 0.3 VDD MIN. 2.00 8 TYP. MAX. 5.50 20 UNIT V TEST CONDITIONS µA µA V kHz VDD − VSS = 3.60 V VDD − VSS = 5.50 V VDD − VSS = 2.0 to 5.5 V IOL = 500 µA VDD − VSS = 2.0 V, Duty 50 % VDD − VSS = 5.50 V µA V V * TP and DATA OUT are N-channel open drain output. A.C. ELECTRICAL CHARACTERISTICS (f = 32.768 kHz, VDD − VSS = 2.0 V, Ta = 25 °C) CHARACTERISTIC C0 to 2, CS − STB Set-up Time STB Pulse Width C0 to 2, CS − STB Hold Time STB LATCH Delay Time CLK-DATA OUT Delay time DATA IN Set-up Time DATA IN Hold Time SYMBOL tSU tSTB tHLD td1 td(c-o) tDSU tDHLD 1 1 MIN. 1 1 1 1** 1 TYP. MAX. UNIT TEST CONDITIONS µs µs µs µs µs µs µs except Time Read mode RL = 33 kΩ, C L = 15 pF ** Note: When a function mode is Time Read mode (other than Test mode), STB LATCH delay time is 20 µs MAX. (td2). 2 BLOCK DIAGRAM OE N-ch OPEN DRAIN DATA OUT MPX CLK DATA IN CLK COMMAND Register 48 Bit Shift Register CLK RH CS C3' C2' C1' C0' 1 Hz YEAR PS MON -TH D/W DAY HOUR MIN SEC Time counter 15 Stage Binary Divider XTAL XTAL OSC Select signal generator circuit 1/215 64 Hz STOP 1 Hz C3' C2' C1' C0' C2 C1 C0 DATA SELECTOR DECODER 1/26 TEST SEC RESET TP MPX CS STB MPX PS D/W CS TP RH : : : : : Multiplexer Preset Day of the Week Chip Select Timing Pulse µPD4990A : Register Hold 3 µPD4990A FUNCTION SPECIFICATIONS • • Crystal frequency (X tal osc.). ° 32.768 kHz Data Data types are: second, minute, day, week, month, and year. Leap years, 31-day months, and months with 30 or less days are adjusted automatically. A 24-hour system is used and last two digits of Gregorian year are indicated. It is assumed that leap years are expressed by multiples of 4. • • Data format Data is represented in BCD notation. Only months are represented in hexadecimal notation. Data input-output and Clock Data is input/output synchronously with reference to the external clocks input from the CLK pin using the serial input/output system. (See Fig. 1.) • Timing pulse output Three frequencies, 64 Hz, 256 Hz, and 2 048 Hz, can be set with C0, C1 and C2 pins. Using serial data input command, selective timing pulses (TPs) are 64 Hz, 256 Hz, 2 048 Hz, and 4 096 Hz and selective output intervals are 1, 10, 30, and 60 seconds. • Function mode selection A function mode can be selected by the inputs from C0, C 1, and C2. Also a function mode can be selected through serial data input. (C0 = C1 = C2 = VDD) Each command is latched with STB (strobe). • • Chip select Connecting the CS pin to the ground level inhibits CLK and STB inputs. Data output inhibition Connecting the OUT ENBL pin to the ground level sets the DATA OUT pin at high impedance. Figure 1. MSB command register Ten's of Unit of year year month LSB day of Ten's of Unit of Ten's of Unit of Ten's of Unit of Ten's of Unit of the week days days hours hours minutes minutes seconds seconds C3' C2' C1' C0' D3 D2 D1 D0 52 Bit Shift Register * DATA of 52 Bit Shift Register appears on DATA OUT terminal from LSB of second. 4 µPD4990A TERMINALS • Input terminals ° ° ° ° ° ° • ° ° • ° ° • ° ° DATA IN CLK C 0, C 1, C 2 STB CS OUT ENBL Data input of 40-/52-bit shift register Shift clock input of 40-/52-bit shift register Command input (3 bit) Strobe input Chip select input (Prohibits CLK & STB) Output control input (Makes the DATA OUT high impedance by inputting low level). Output terminals (N-channel Open Drain) DATA OUT TP Data output of 40-/52-bit shift register Timing pulse output Oscillation terminals XTAL XTAL Oscillation inverter input (OSC IN) Oscillation inverter output (OSC OUT) Power supply terminals VDD GND (VSS) Plus power supply Common line 5 µPD4990A COMMAND SPECIFICATIONS ° Commands input from C0, C1, and C2 pins (1 ...H, 0 ...L) Shift register 40 bit (The year function is ineffective.) (Operates as the existing µPD1990AC in other than test mode) C2 0 0 0 0 1 1 1 1 C1 0 0 1 1 0 0 1 1 C0 0 1 0 1 0 1 0 1 Register Hold Register Shift Time Set & Counter Hold Time Read TP = 64 Hz TP = 256 Hz TP = 2 048 Hz Serial command transfer mode FUNCTION DATA OUT = 1 Hz DATA OUT = [LSB] = 0 or 1 DATA OUT = [LSB] = 0 or 1 DATA OUT = 1 Hz * The test mode is cancelled by [C2, C1, C0] = [0, 0, 0] to [1, 1, 0]. ° Serial data commands Set [C2, C1, C0] = [1, 1, 1] at all time. Shift register 52 bit (The year function is effective.) C 3' 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 C 2' 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 C1' 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 C0' 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Register Hold Register Shift Time Set & Counter Hold Time Read TP = 64 Hz TP = 256 Hz TP = 2 048 Hz TP = 4 096 Hz TP = 1 s interval set (counter reset & start) TP = 10 s interval set (counter reset & start) TP = 30 s interval set (counter reset & start) TP = 60 s interval set (counter reset & start) Interval Output Flag Reset Interval Timer Clock Run Interval Timer Clock Stop TEST MODE SET FUNCTION DATA OUT = 1 Hz DATA OUT = [LSB] = 0 or 1 DATA OUT = [LSB] = 0 or 1 DATA OUT = 1 Hz When serial data commands are used, C0, C1, and C2 pins should be connected V DD pin. 6 µPD4990A • Command input (1) 3-bit binary code input: C2, C1, C0 (2) 4-bit serial transfer command input: C3', C2', C1', C0' • Number of commands C2, C1, C0 Register control TP select TP control Test mode set 4 3 0 1 C'3, C'2, C' 1, C' 0 4 8 3 1 • Commands (C3', C2', C1', C0' commands are made effective only when [C2, C1, C0] = [1, 1, 1].) (1) Register control [C2, C1, C0] / [C3', C2', C1', C0'] [0, 0, 0] / [0, 0, 0, 0] ° Register Hold Mode [C2, C1, C0] The 40-bit shift register is held. The year function is ineffective. [C3', C2', C1', C0'] The 48-bit shift register is held. The command register is not held. * The DATA OUT output frequency is 1 Hz. ° Register Shift Mode [C2, C1, C0] [0, 0, 1] / [0, 0, 0, 1] The 40-bit shift register data can be shifted. The year function is ineffective. [C3', C2', C1', C0'] Data in 52-bit shift registers (including command registers) can be shifted. For command register, data can be always shifted using the serial command transfer mode. * The DATA OUT output is LSB data from the shift register. ° Time Set and Counter Hold Mode [C2, C1, C0] [0, 1, 0] / [0, 0, 1, 0] Data is transferred from the 40-bit shift register to the time counter. The year function is ineffective. [C3', C2', C1', C0'] Data is transferred from the 48-bit shift register to the time counter. * This command is used to reset the last 10-15 of 15 Stage Binary Divider and holds the time counter. 15 Stage Binary Divider resetting and time counter release are executed by the following: [C2, C1, C0] = [0, 0, 0] [0, 0, 1] [0, 1, 1] [C3', C2', C1', C0'] = [0, 0, 0, 0] [0, 0, 0, 1] [0, 0, 1, 1] The time setting accuracy is ±15.625 ms. The DATA OUT pin outputs LSB data (0 or 1) from the shift register. After this command is executed, the 40-/48-bit shift register is held and data cannot be shifted. ° Time Read Mode [C2, C1, C0] [0, 1, 1] / [0, 0, 1, 1] Data is transferred from the time-counter to the 40-bit shift register. The year function is ineffective. [C3', C2', C1', C0'] Data is transferred from the time counter to the 48-bit shift register. * The DATA OUT pin output is a 1 Hz frequency. After this command is executed, the 40-/48-bit shift register is held and data cannot be shifted. 7 µPD4990A (2) TP selection and control [C2, C1, C0] / [C3', C2', C1', C0'] • • • TP = 64 Hz Set Mode [1, 0, 0] / [0, 1, 0, 0] 64 Hz (50 % duty) is output to the TP pin. [C2, C1, C0]: The year function is ineffective and the interval timer stops. TP = 256 Hz Set Mode [1, 0, 1] / [0, 1, 0, 1] 256 Hz (50 % duty) is output to the TP pin. [C2, C1, C0]: The year function is ineffective and the interval timer stops. TP = 2 048 Hz Set Mode [1, 1, 0] / [0, 1, 1, 0] 2 048 Hz (50 % duty) is output to the TP pin. [C2, C1, C0]: The year function is ineffective and the interval timer stops. Modes permitted only for serial commands [C3', C2', C1', C0'] • • • • • • • • TP = 4 098 Hz Set Mode [0, 1, 1, 1] 4 098 Hz (50 % duty) is output to the TP pin. The interval timer stops. TP = 1-second Interval Set Mode (counter reset & start) [1, 0, 0, 0] A 1-second interval signal is output to the TP pin. TP = 10-second Interval Set Mode (counter reset & start) [1, 0, 0, 1] A 10-second interval signal is output to the TP pin. TP = 30-second Interval Set Mode (counter reset & start) [1, 0, 1, 0] A 30-second interval signal is output to the TP pin. TP = 60-second Interval Set Mode (counter reset & start) [1, 0, 1, 1] A 60-second interval signal is output to the TP pin. Interval Output Flag Reset [1, 1, 0, 0] The interval signal output to the TP pin is reset. The interval timer counter continue the operation. Interval Timer Clock Run [1, 1, 0, 1] The timer for outputting interval signals is reset then started. Interval Timer Clock Stop [1, 1, 1, 0] The timer for outputting interval signals stops. The output status does not change. (3) Serial command transfer mode setting Set [C2, C1, C0] = [1, 1, 1] (4) Test mode setting Set [C2, C1, C0] = [1, 1, 1] [C3', C2', C1', C0'] = [1, 1, 1, 1] ° 3-bit parallel command setting mode [C2, C1, C0] The year function is ineffective when commands are input through C2, C1, and C0 pins. Generally, February involves 28 days. The 29th day can be set optionally. The next day of the February 29th can be set the March 1st automatically. The interval timer is in the halt state. * The test mode is cancelled by [C2, C1, C0] = [0, 0, 0] to [1, 1, 0]. ° Serial command transfer mode [C3', C2', C1', C0'] If a strobe signal is input with C 2, C1, and C0 pins set at the VDD level ([1, 1, 1]), the contents of the serial command register ([C3', C2', C1', C0']) are received as a command; the year function is effective. * The test mode is cancelled by [C3', C2', C1', C0'] = [0, 0, 0] = [0, 1, 0, 0] to [1, 1, 1, 0] In this mode, the serial command register is not held with the Register Hold command. Accordingly, the serial command can be executed irrespective of the mode if the CS pin is active. The year function is effective in the serial command transfer mode. 8 µPD4990A ° Interval output function An interrupt signal can be output by selecting an output from TP. Interrupt signals are output repeatedly at specified intervals until their output is suppressed by a command. Only output flags can be reset to operate the timer continuously. 0.5 s 1s 1s 1s Interval Output Flag Reset Interval of 1 second Interval Timer Clock Stop The interval signal waveform is rectangular (50 % duty) if not reset. The interval timer is independent of the Timer Counter, so it is not affected by the resetting of the current time timer. 30 s 60 s Interval Output Flag Reset The interval timer accuracy is ±15.625 ms. * The interval timer counter is reset by [1, 0, 0, 0] through [1, 0, 1, 1]. 9 µPD4990A ° Test mode In the test mode, data is output to the DATA OUT pin regardless of whether data has been input to OUT ENBL. There are two different test modes depending on the OUT ENBL data. (1) Test mode 1 (OUT ENBL = 0) 8 192 Hz signals are set parallel in the counters for year, month, week, day, time, minute, and second. There is no carry from these counters. Year counter Month counter Week counter Day counter Time counter Minute counter Second counter 8 192 Hz (2) Test mode 2 (OUT ENBL = 1) A 8 192 Hz signal is input to the second counter instead of the 1 Hz signal. There is carry from counters. Year counter Month counter Week counter Day counter Time counter Minute counter Second counter 8 192 Hz Outputs from DATA OUT and TP OUT pins in different function modes are listed below. MODE REGISTER HOLD REGISTER SHIFT TIME SET TIME READ DATA OUT 1 Hz LSB of shift register LSB of shift register 1 Hz TP 64 Hz 32 Hz L Level 32 Hz Test mode 8 192 Hz input to time counter Others By this command, TEST MODE is released. 8 192 Hz input to time counter When the REGISTER HOLD command cancels the test mode, 64 Hz is output to the TP pin. 10 µPD4990A TIMING DIAGRAM FOR SETTING COMMANDS (C0', C1', C2', C3') Figure 2. DATA IN VIH VIL tDSU VIH VIL C0' C1' tDHLD C2' C3' VIH VIL CLK VIH VIL tHLD VIH tSTB STB VIL Other than time read mode NEW COMMAND VALID OLD MODE td1 NEW MODE Time read mode OLD MODE td2 NEW MODE VDD − VSS = 2.0 V tDSU = 1 µs MIN. tDHLD = 1 µs MIN. tHLD = 1 µs MIN. tSTB = 1 µs MIN. td1 td2 = 1 µs MAX. (Other than time read mode) = 20 µs MAX. (Time read mode) Note: Command (C 2, C1, C0) is set to (1, 1, 1) CS = "H" A mode is latched by STB and held until another mode in the same group is set. 11 µPD4990A TIMING DIAGRAM FOR SETTING COMMANDS (C0, C1, C2) Figure 3. CAN CHANGE VIH VIL tSU VIH CS tSU tSTB STB VIH VIL tS-C CLK VIL Other than time read mode td1 NEW COMMAND VALID OLD MODE Time read mode td2 OLD MODE NEW MODE NEW MODE tS-C tHLD tHLD VIH STABLE CAN CHANGE VIH VIL C2,C1,C0 VDD − VSS = 2.0 V tSU = 1 µs MIN. tHLD = 1 µs MIN. tSTB = 1 µs MIN. td1 td2 tS-C = 1 µs MAX. (Other than time read mode) = 20 µs MAX. (Time read mode) = 1 µs MIN. Note: A mode is latched by STB and held until another mode in the same group is set. 12 µPD4990A DATA INPUT/OUTPUT TIMING DIAGRAM Figure 4. Command (C2, C1, C0) is set to (1, 1, 1). Command (C3', C2', C0') is set to [0001] (Register Shift Mode). CS = "H" CLK "1" s. DATA IN "10" s. "1" min. "1" year "10" year '70 July 16 (Sun.) 2 hours 24 minutes 35 seconds. INPUT TIMING OUT ENBL "1" s. "10" s. "1" min. "1" year "10" year OUTPUT TIMING DATA OUT 0 1 2 3 4 5 6 7 8 9 1011 4041424344454647 '86 November 25 (Sat.) 2 hours 23 minutes 49 seconds. Written-in data LSB ("H") appears at output. Note: Reading-in timing of CPU (Trailing edge of CLK). TIMING DIAGRAM OF DATA INPUT AND OUTPUT Figure 5. VIH CLK VIL tdC-O VOH DATA OUT VOL tDSU VIH DATA IN VIL tDHLD tdC-O : 1 µ s MAX. (RL = 33 kΩ, CL = 25 pF) tDSU : 1 µ s MIN. tDHLD : 1 µ s MIN. 13 µPD4990A POWER SUPPLY CIRCUIT 1SS53 µ PD4990A +5 V 2SA733 VDD C0 15 kΩ 1 kΩ 510 Ω C1 1SS53 C2 10 kΩ OE 2SC945 4.7 kΩ 3.6 V Ni−Cd DIN CLK STB 32.768 kHz CG = 20 pF XTAL CS Power Fail GND VSS XTAL CD = 5 to 30 pF +5 V TP DOUT 10 kΩ 14 µPD4990A APPLICATION +5 V 10 kΩ DATA BUS D7 D6 D5 D4 D3 D2 D1 D0 WR Power Fail 4 5 12 D0 D1 D2 Q0 Q1 Q2 2 7 10 CS DIN CLK STB RESET of SYSTEM DOUT OE +5 V 10 kΩ RD Address Decoder 13 D3 9 Q3 15 1 CLK RESET VDD C0 C1 TP 32.768 kHz CG = 20 pF XTAL INT µ PD4175BC Power Supply Circuit C2 XTAL CD = 5 to 30 pF µ PD4990A 15 µPD4990A 14PIN PLASTIC DIP (300 mil) 14 8 1 A 7 K I L J H G F D N M C B M R NOTES 1) Each lead centerline is located within 0.25 mm (0.01 inch) of its true position (T.P.) at maximum material condition. 2) Item "K" to center of leads when formed parallel. ITEM A B C D F G H I J K L M N R MILLIMETERS 20.32 MAX. 2.54 MAX. 2.54 (T.P.) 0.50±0.10 1.2 MIN. 3.5±0.3 0.51 MIN. 4.31 MAX. 5.08 MAX. 7.62 (T.P.) 6.4 0.25 +0.10 –0.05 0.25 0~15 ° INCHES 0.800 MAX. 0.100 MAX. 0.100 (T.P.) 0.020 +0.004 –0.005 0.047 MIN. 0.138±0.012 0.020 MIN. 0.170 MAX. 0.200 MAX. 0.300 (T.P.) 0.252 0.010 +0.004 –0.003 0.01 0~15 ° P14C-100-300A,C-1 16 µPD4990A 16 PIN PLASTIC SOP (300 mil) 16 9 detail of lead end 1 A G 8 H I J F K E C D M N M B L NOTE Each lead centerline is located within 0.12 mm (0.005 inch) of its true position (T.P.) at maximum material condition. ITEM MILLIMETERS A B C D E F G H I J K L M N P 10.46 MAX. 0.78 MAX. 1.27 (T.P.) 0.40 +0.10 –0.05 0.1±0.1 1.8 MAX. 1.55 7.7±0.3 5.6 1.1 0.20 +0.10 –0.05 0.6±0.2 0.12 0.10 ° 3 ° +7° –3 P INCHES 0.412 MAX. 0.031 MAX. 0.050 (T.P.) 0.016 +0.004 –0.003 0.004±0.004 0.071 MAX. 0.061 0.303±0.012 0.220 0.043 0.008 +0.004 –0.002 0.024 +0.008 –0.009 0.005 0.004 ° 3 ° +7° –3 P16GM-50-300B-4 17 µPD4990A [MEMO] 18 µPD4990A [MEMO] 19 µPD4990A No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. NEC devices are classified into the following three quality grades: "Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific application. The recommended applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance. Anti-radioactive design is not implemented in this product. M4 96.5