UPD753104

User’s Manual µPD753108 4-bit Single-chip Microcontrollers µPD753104 µPD753106 µPD753108 µPD75P3116 Document No. U10890EJ3V0UM00 (3rd edition) Date Published March 1998 N CP(K) © Printed in Japan 1995 [MEMO] 2 NOTES FOR CMOS DEVICES 1 PRECAUTION AGAINST ESD FOR SEMICONDUCTORS Note: Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and ultimately degrade the device operation. Steps must be taken to stop generation of static electricity as much as possible, and quickly dissipate it once, when it has occurred. Environmental control must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using insulators that easily build static electricity. Semiconductor devices must be stored and transported in an anti-static container, static shielding bag or conductive material. All test and measurement tools including work bench and floor should be grounded. The operator should be grounded using wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need to be taken for PW boards with semiconductor devices on it. 2 HANDLING OF UNUSED INPUT PINS FOR CMOS Note: No connection for CMOS device inputs can be cause of malfunction. If no connection is provided to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence causing malfunction. CMOS devices behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected to VDD or GND with a resistor, if it is considered to have a possibility of being an output pin. All handling related to the unused pins must be judged device by device and related specifications governing the devices. 3 STATUS BEFORE INITIALIZATION OF MOS DEVICES Note: Power-on does not necessarily define initial status of MOS device. Production process of MOS does not define the initial operation status of the device. Immediately after the power source is turned ON, the devices with reset function have not yet been initialized. Hence, power-on does not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the reset signal is received. Reset operation must be executed immediately after poweron for devices having reset function. QTOP is a trademark of NEC Corporation. MS-DOS is either a registered trademark or a trademark of Microsoft Corporation in the United States and/or other countries. IBM DOS, PC/AT, and PC DOS are trademarks of International Business Machines Corporation. 3 The export of this product from Japan is regulated by the Japanese government. To export this product may be prohibited without governmental license, the need for which must be judged by the customer. The export or re-export of this product from a country other than Japan may also be prohibited without a license from that country. Please call an NEC sales representative. The information in this document is subject to change without notice. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. NEC devices are classified into the following three quality grades: "Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a customer designated “quality assurance program“ for a specific application. The recommended applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance. Anti-radioactive design is not implemented in this product. M7 96.5 4 Regional Information Some information contained in this document may vary from country to country. Before using any NEC product in your application, please contact the NEC office in your country to obtain a list of authorized representatives and distributors. They will verify: • Device availability • Ordering information • Product release schedule • Availability of related technical literature • Development environment specifications (for example, specifications for third-party tools and components, host computers, power plugs, AC supply voltages, and so forth) • Network requirements In addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary from country to country. NEC Electronics Inc. (U.S.) Santa Clara, California Tel: 408-588-6000 800-366-9782 Fax: 408-588-6130 800-729-9288 NEC Electronics (Germany) GmbH Benelux Office Eindhoven, The Netherlands Tel: 040-2445845 Fax: 040-2444580 NEC Electronics Hong Kong Ltd. Hong Kong Tel: 2886-9318 Fax: 2886-9022/9044 NEC Electronics Hong Kong Ltd. NEC Electronics (France) S.A. Velizy-Villacoublay, France Tel: 01-30-67 58 00 Fax: 01-30-67 58 99 Seoul Branch Seoul, Korea Tel: 02-528-0303 Fax: 02-528-4411 NEC Electronics (Germany) GmbH Duesseldorf, Germany Tel: 0211-65 03 02 Fax: 0211-65 03 490 NEC Electronics (France) S.A. NEC Electronics (UK) Ltd. Milton Keynes, UK Tel: 01908-691-133 Fax: 01908-670-290 Spain Office Madrid, Spain Tel: 01-504-2787 Fax: 01-504-2860 NEC Electronics Singapore Pte. Ltd. United Square, Singapore 1130 Tel: 65-253-8311 Fax: 65-250-3583 NEC Electronics Taiwan Ltd. NEC Electronics Italiana s.r.1. Milano, Italy Tel: 02-66 75 41 Fax: 02-66 75 42 99 NEC Electronics (Germany) GmbH Scandinavia Office Taeby, Sweden Tel: 08-63 80 820 Fax: 08-63 80 388 Taipei, Taiwan Tel: 02-719-2377 Fax: 02-719-5951 NEC do Brasil S.A. Cumbica-Guarulhos-SP, Brasil Tel: 011-6465-6810 Fax: 011-6465-6829 J98. 2 5 Major Revisions in this Edition Page Throughout p. 41 p. 71 p. 122 Description Data bus pins (D0 to D7) are added. Table 2-3 List of Recommended Connections for Unused Pins is changed. Caution in Table 4-1 Differences between Mk I Mode and Mk II Mode is changed. Description on feedback resistor mask option in 5.2.2 (6) Subsystem clock oscillator control register (SOS) is deleted. p. 124 p. 125 p. 238 p. 340 p. 353 p. 354 p. 358 p. 449 Table 5-5 Maximum Time Required to Switch System to/from CPU Clocks is changed. Figure 5-19 Switching between System Clock and CPU Clock is changed. Cautions are added to 5.6.7 (a) Bus release signal (REL) and 5.6.7 (b) Command signal (CMD). 7.4 Mask Option Selection is added. 9.2 Writing Program Memory is changed. 9.3 Reading Program Memory is changed. 10.3 Mask Option of Feedback Resistor for Subsystem Clock is deleted. Ordering media in APPENDIX C ORDERING MASK ROMS are changed. The mark shows major revised points. 6 INTRODUCTION Readers: This manual is intended for user engineers who understand the functions of the µ PD753104, 753106, 753108, and 75P3116 4-bit single-chip microcontrollers, and wish to design application systems using any of these microcontrollers. Purpose: This manual describes the hardware functions of the µ PD753104, 753106, 753108, and 75P3116 in the organization described below. Organization: This manual contains the following information: • General • Pin Functions • Features of Architecture and Memory Map • Internal CPU Functions • Peripheral Hardware Functions • Interrupt Functions and Test Functions • Standby Functions • Reset Function • Writing and Verifying PROM • Mask options • Instruction Set How to Read This Manual: It is assumed that readers for this manual have general knowledge on electricity, logic circuits, and microcontrollers. • If you have experience of using the µ PD75308B, → Read APPENDIX A µ PD75308B, 753108, AND 75P3116 FUNCTIONAL LIST to check differences between the µ PD75308B and the microcontrollers described in this manual. • If you use this manual as the manual for the µ PD753104, 753106, and 75P3116, → Unless otherwise specified, the µPD753108 is regarded as the representative model, and description throughout this manual is focused on this model. Refer to section 1.3 Differences among µ PD753108 Subseries Products to check the differences among the respective models. • To check the functions of an instruction whose mnemonic is known, → Refer to APPENDIX D INSTRUCTION INDEX . • To check the functions of a specific internal circuit, → Refer to APPENDIX E HARDWARE INDEX. • To understand the overall functions of the µ PD753104, 753106, 753108, and 75P3116, → Read this manual in the order of Contents. 7 Legend Data significance Active low Address of memory map Note Caution Remark Numeric notation : Left: higher, right: lower : ××× (top bar over signal or pin name) : Top: low, Bottom: high : Footnote : Important information : Supplement : Binary .................. ×××× or ××××B Decimal ............... ×××× Hexadecimal ....... ××××H Important point and emphasis : Bold letters 8 Related Documents The related documents indicated in this publication may include preliminary versions. However, preliminary versions are not marked as such. Documents related to devices Document Name Document Number English Japanese U10890J U10086J U11369J IEM-5600 U10453J µ PD753108 User’s Manual µ PD753104, 753106, 753108 Data Sheet µ PD75P3116 Data Sheet µ PD753108 Instruction Table 75XL Series Selection Guide U10890E (This manual) U10086E U11369E — U10453E Documents related to development tools Document Number Document Name English Hardware IE-75000-R/IE-75001-R User’s Manual IE-75300-R-EM User’s Manual EP-753108GC/GK-R User’s Manual PG-1500 User’s Manual Software RA75X Assembler Package User’s Manual PG-1500 Controller User’s Manual Operation Language PC-9800 series (MS-DOS TM-based) DOSTM-based) EEU-1416 U11354E EEU-1495 U11940E U12622E U12385E EEU-1291 U10540E Japanese EEU-846 U11354J EEU-968 U11940J U12622J U12385J EEU-704 EEU-5008 IBM PC series (PC Other documents Document Name IC Package Manual Semiconductor Device Mounting Technology Manual Quality Grades on NEC Semiconductor Devices NEC Semiconductor Device Reliability/Quality Control System Guide to Prevent Damage for Semiconductor Devices by Electrostatic Discharge (ESD) Guide to Quality Assurance for Semiconductor Devices Microcomputer Product Series Guide Document Number English C10943X C10535E C11531E C10983E C11892E MEI-1202 — C10535J C11531J C10983J C11892J — U11416J Japanese Caution The above related documents are subject to change without notice. Be sure to use the latest edition when you design your system. 9 [MEMO] 10 CONTENTS CHAPTER 1 1.1 1.2 1.3 1.4 1.5 GENERAL .................................................................................................................. 21 22 23 23 24 25 Functional Outline .............................................................................................................................. Ordering Information ......................................................................................................................... Differences among µPD753108 Subseries Products .................................................................... Block Diagram ..................................................................................................................................... Pin Configuration (Top View) ........................................................................................................... CHAPTER 2 2.1 2.2 PIN FUNCTION ........................................................................................................ 27 27 31 31 32 32 33 33 33 33 33 34 34 35 35 35 35 35 35 35 36 36 36 37 37 37 37 37 37 38 41 Pin Functions of µ PD753108 ............................................................................................................ Pin Functions ...................................................................................................................................... 2.2.1 2.2.2 2.2.3 2.2.4 2.2.5 2.2.6 2.2.7 2.2.8 2.2.9 2.2.10 2.2.11 2.2.12 2.2.13 2.2.14 2.2.15 2.2.16 2.2.17 2.2.18 2.2.19 2.2.20 2.2.21 2.2.22 2.2.23 2.2.24 2.2.25 2.2.26 P00 to P03 (PORT0), P10 to P13 (PORT1) ......................................................................... P20 to P23 (PORT2), P30 to P33 (PORT3), P50 to P53 (PORT5), P60 to P63 (PORT6), P80 to P83 (PORT8), and P90 to P93 (PORT9) ................................................................. TI0 to TI2 ................................................................................................................................. PTO0 to PTO2 ........................................................................................................................ PCL .......................................................................................................................................... BUZ .......................................................................................................................................... SCK, SO/SB0, and SI/SB1 .................................................................................................... INT4 ......................................................................................................................................... INT0 and INT1 ........................................................................................................................ INT2 ......................................................................................................................................... KR0 to KR3 ............................................................................................................................. S0 to S23 ................................................................................................................................ COM0 to COM3 ...................................................................................................................... VLC0 to V LC2 ............................................................................................................................. BIAS ........................................................................................................................................ LCDCL ..................................................................................................................................... SYNC ....................................................................................................................................... X1 and X2 ............................................................................................................................... XT1 and XT2 ........................................................................................................................... RESET ..................................................................................................................................... MD0 to MD3 (µ PD75P3116 only).......................................................................................... D0 to D7 (µ PD75P3116 only) ................................................................................................ IC (µ PD753104, 753106, and 753108 only) ........................................................................ VPP (µ PD75P3116 only) ......................................................................................................... VDD ........................................................................................................................................... VSS ........................................................................................................................................... 2.3 2.4 Pin Input/Output Circuits .................................................................................................................. Recommended Connections for Unused Pins .............................................................................. CHAPTER 3 3.1 3.1.1 3.1.2 3.2 3.3 FEATURES OF ARCHITECTURE AND MEMORY MAP ................................. Bank configuration of data memory ...................................................................................... Addressing mode of data memory ........................................................................................ 43 43 43 45 59 64 Bank Configuration of Data Memory and Addressing Mode ...................................................... Bank Configuration of General-Purpose Registers ...................................................................... Memory-Mapped I/O ........................................................................................................................... 11 CHAPTER 4 4.1 4.1.1 4.1.2 4.2 4.3 4.4 INTERNAL CPU FUNCTIONS ............................................................................... Difference between Mk I and Mk II modes .......................................................................... Setting method of stack bank selection register (SBS) ....................................................... 71 71 71 72 73 74 79 79 80 84 85 85 89 93 Switching Function between Mk I Mode and Mk II Mode ............................................................ Program Counter (PC) ....................................................................................................................... Program Memory (ROM) .................................................................................................................... Data Memory (RAM) ........................................................................................................................... 4.4.1 4.4.2 Configuration of data memory ............................................................................................... Specifying bank of data memory ........................................................................................... 4.5 4.6 4.7 4.8 4.9 General-Purpose Registers ............................................................................................................... Accumulators ...................................................................................................................................... Stack Pointer (SP) and Stack Bank Selection Register (SBS) ................................................... Program Status Word (PSW) ............................................................................................................ Bank Selection Register (BS) ........................................................................................................... CHAPTER 5 5.1 5.1.1 5.1.2 5.1.3 5.1.4 5.1.5 5.1.6 5.2 5.2.1 5.2.2 5.2.3 5.2.4 5.3 5.3.1 5.3.2 5.3.3 5.3.4 5.3.5 5.3.6 5.4 5.4.1 5.4.2 5.5 5.5.1 5.5.2 5.5.3 5.5.4 5.5.5 5.5.6 PERIPHERAL HARDWARE FUNCTION .............................................................. Types, features, configuration of digital I/O ports ............................................................... Setting I/O mode .................................................................................................................... Digital I/O port manipulation instruction ............................................................................... Operation of digital I/O port ................................................................................................... Connecting pull-up resistors .................................................................................................. I/O timing of digital I/O port ................................................................................................... Clock generator configuration ............................................................................................... Clock generator function and operation ............................................................................... Setting of system clock and CPU clock ................................................................................ Clock output circuit ................................................................................................................. Basic interval timer/watchdog timer configuration ............................................................... Basic interval timer mode register (BTM) ............................................................................. Watchdog timer enable flag (WDTM) ................................................................................... Basic interval timer operations .............................................................................................. Watchdog timer operations .................................................................................................... Other functions ....................................................................................................................... Configuration of watch timer .................................................................................................. Watch mode register .............................................................................................................. Configuration of timer/event counter .................................................................................... 8-bit timer/event counter mode operation ............................................................................ PWM pulse generator mode (PWM mode) operation .......................................................... 16-bit timer/event counter mode operation .......................................................................... Carrier generator mode (CG mode) operation ..................................................................... Notes on using timer/event counter ...................................................................................... 95 95 96 101 103 106 108 110 112 112 113 124 126 129 129 130 132 133 134 136 138 138 139 141 141 151 165 171 184 196 Digital I/O Port ..................................................................................................................................... Clock Generator .................................................................................................................................. Basic Interval Timer/Watchdog Timer ............................................................................................. Watch Timer ......................................................................................................................................... Timer/Event Counter .......................................................................................................................... 12 5.6 Serial Interface .................................................................................................................................... 5.6.1 5.6.2 5.6.3 5.6.4 5.6.5 5.6.6 5.6.7 5.6.8 Serial interface function ......................................................................................................... Configuration of serial interface ............................................................................................ Register function ..................................................................................................................... Operation stop mode .............................................................................................................. Operation in 3-wire serial I/O mode ...................................................................................... Operation in 2-wire serial I/O mode ...................................................................................... SBI mode operation ............................................................................................................... SCK pin output manipulation ................................................................................................. LCD controller/driver configuration ....................................................................................... LCD controller/driver functions .............................................................................................. Display mode register (LCDM) .............................................................................................. Display control register (LCDC) ............................................................................................ LCD/port selection register (LPS) ......................................................................................... Display data memory ............................................................................................................. Common signal and segment signal ..................................................................................... Supply of LCD drive power VLC0, VLC1 , and VLC2 ................................................................. Display mode .......................................................................................................................... 203 203 204 208 216 218 228 235 268 269 269 271 271 273 275 276 278 282 285 298 5.7 LCD Controller/Driver ........................................................................................................................ 5.7.1 5.7.2 5.7.3 5.7.4 5.7.5 5.7.6 5.7.7 5.7.8 5.7.9 5.8 Bit Sequential Buffer .......................................................................................................................... CHAPTER 6 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 INTERRUPT FUNCTION AND TEST FUNCTION ............................................. 301 301 303 305 313 314 316 318 320 320 328 328 328 Configuration of Interrupt Control Circuit ..................................................................................... Types of Interrupt Sources and Vector Tables ............................................................................. Hardware Controlling Interrupt Function ....................................................................................... Interrupt Sequence ............................................................................................................................. Multiple Interrupt Service Control ................................................................................................... Vector Address Share Interrupt Service ........................................................................................ Machine Cycles until Interrupt Processing .................................................................................... Effective Usage of Interrupt .............................................................................................................. Application of Interrupt ..................................................................................................................... 6.10.1 6.10.2 Types of test sources ............................................................................................................. Hardware devices controlling test function .......................................................................... 6.10 Test Function ...................................................................................................................................... CHAPTER 7 7.1 7.2 7.3 7.4 7.5 STANDBY FUNCTION ............................................................................................. 333 335 337 339 340 340 Standby Mode Setting and Operation Status ................................................................................ Standby Mode Release ...................................................................................................................... Operation After Releasing Standby Mode ...................................................................................... Mask Option Selection ....................................................................................................................... Application of Standby Mode ........................................................................................................... CHAPTER 8 CHAPTER 9 9.1 9.2 9.3 9.4 RESET FUNCTION .................................................................................................. 347 WRITING AND VERIFYING PROM (PROGRAM MEMORY) .......................... 351 352 353 354 355 Operation Mode for Writing/Verifying Program Memory ............................................................. Writing Program Memory .................................................................................................................. Reading Program Memory ................................................................................................................ Screening of One-Time PROM ......................................................................................................... 13 CHAPTER 10 10.1.1 10.1.2 MASK OPTION ........................................................................................................ 357 357 357 357 358 Mask option of P50 through P53 .......................................................................................... Mask option of VLC0 through VLC2 .......................................................................................... 10.1 Pins ....................................................................................................................................................... 10.2 Mask Option of Standby Function ................................................................................................... CHAPTER 11 11.1.1 11.1.2 11.1.3 11.1.4 11.1.5 INSTRUCTION SET ............................................................................................... 359 359 359 360 360 361 362 363 383 389 390 396 400 401 409 410 412 414 415 419 424 429 430 432 433 GETI instruction ...................................................................................................................... Bit manipulation instruction ................................................................................................... String-effect instruction .......................................................................................................... Base number adjustment instruction .................................................................................... Skip instruction and number of machine cycles required for skipping ............................... 11.1 Unique Instructions ............................................................................................................................ 11.2 Instruction Sets and their Operations ............................................................................................ 11.3 Op Code of Each Instruction ............................................................................................................ 11.4 Instruction Function and Application ............................................................................................. 11.4.1 11.4.2 11.4.3 11.4.4 11.4.5 11.4.6 11.4.7 11.4.8 11.4.9 Transfer instructions ............................................................................................................... Table reference instructions .................................................................................................. Bit transfer instructions .......................................................................................................... Operation instructions ............................................................................................................ Accumulator manipulation instructions ................................................................................. Increment/decrement instructions ......................................................................................... Compare instructions ............................................................................................................. Carry flag manipulation instructions ..................................................................................... Memory bit manipulation instructions ................................................................................... 11.4.10 Branch instructions ................................................................................................................. 11.4.11 Subroutine stack control instructions .................................................................................... 11.4.12 Interrupt control instructions .................................................................................................. 11.4.13 Input/output instructions ......................................................................................................... 11.4.14 CPU control instructions ........................................................................................................ 11.4.15 Special instructions ................................................................................................................ APPENDIX A APPENDIX B APPENDIX C APPENDIX D D.1 D.2 µPD75308B, 753108 AND 75P3116 FUNCTIONAL LIST .............................. 437 DEVELOPMENT TOOLS ....................................................................................... 441 ORDERING MASK ROMS .................................................................................... 449 INSTRUCTION INDEX ........................................................................................... 451 451 453 Instruction Index (by function) ........................................................................................................ Instruction Index (alphabetical order) ............................................................................................ APPENDIX E APPENDIX F HARDWARE INDEX ............................................................................................... 455 REVISION HISTORY ............................................................................................... 457 14 LIST OF FIGURES (1/4) Figure 3-1 3-2 3-3 3-4 3-5 3-6 3-7 4-1 4-2 4-3 4-4 4-5 4-6 4-7 4-8 4-9 4-10 4-11 4-12 4-13 4-14 4-15 5-1 5-2 5-3 5-4 5-5 5-6 5-7 5-8 5-9 5-10 5-11 5-12 5-13 5-14 5-15 5-16 5-17 5-18 5-19 5-20 Title Selecting MBE = 0 Mode and MBE = 1 Mode .............................................................................. Data Memory Configuration and Addressing Range for Each Addressing Mode ....................... Static RAM Address Update Method .............................................................................................. Example of Using Register Banks .................................................................................................. General-Purpose Register Configuration (for 4-bit operation) ..................................................... General-Purpose Register Configuration (for 8-bit operation) ..................................................... Page 44 46 52 60 62 63 66 72 73 75 81 83 84 84 85 86 87 87 88 88 89 93 95 97 98 98 99 µ PD753108 I/O Map ........................................................................................................................ Stack Bank Selection Register Format .......................................................................................... Program Counter Configuration ...................................................................................................... Program Memory Map ..................................................................................................................... Data Memory Map ........................................................................................................................... Configuration of Display Data Memory .......................................................................................... General-Purpose Register Configuration ....................................................................................... Register Pair Configuration ............................................................................................................. Accumulators .................................................................................................................................... Stack Pointer and Stack Bank Selection Register Configuration ................................................ Data Saved in Stack Memory (Mk I mode) .................................................................................... Data Restored from Stack Memory (Mk I mode) .......................................................................... Data Saved in Stack Memory (Mk II mode) ................................................................................... Data Restored from Stack Memory (Mk II mode) ......................................................................... Program Status Word Configuration .............................................................................................. Bank Selection Register Configuration .......................................................................................... Digital Ports Data Memory Addresses ........................................................................................... Ports 0, 1 Configuration .................................................................................................................. Ports 3, 6 Configuration .................................................................................................................. Port 2 Configuration ......................................................................................................................... Port 5 Configuration ......................................................................................................................... Ports 8, 9 Configuration .................................................................................................................. 100 Port Mode Register Formats ........................................................................................................... 102 Pull-Up Resistor Specify Register Formats ................................................................................... 109 I/O Timing of Digital I/O Port .......................................................................................................... 110 ON Timing of On-Chip Pull-up Resistor Connected via Software ............................................... 111 Clock Generator Block Diagram ..................................................................................................... 112 Processor Clock Control Register Format ..................................................................................... 115 System Clock Control Register Format .......................................................................................... 116 Main System Clock Oscillator External Circuit .............................................................................. 117 Subsystem Clock Oscillator External Circuit ................................................................................. 117 Example of Connecting Resonator Incorrectly .............................................................................. 118 Subsystem Clock Oscillator ............................................................................................................ 121 Subsystem Clock Oscillator Control Register (SOS) Format ....................................................... 123 Switching between System Clock and CPU Clock ........................................................................ 125 Clock Output Circuit Block Diagram ............................................................................................... 126 15 LIST OF FIGURES (2/4) Figure 5-21 5-22 5-23 5-24 5-25 5-26 5-27 5-28 5-29 5-30 5-31 5-32 5-33 5-34 5-35 5-36 5-37 5-38 5-39 5-40 5-41 5-42 5-43 5-44 5-45 5-46 5-47 5-48 5-49 5-50 5-51 5-52 5-53 5-54 5-55 5-56 5-57 5-58 5-59 5-60 5-61 5-62 5-63 5-64 Title Page Clock Output Mode Register Format .............................................................................................. 127 Application Example of Remote Control Waveform Output ......................................................... 128 Basic Interval Timer/Watchdog Timer Block Diagram .................................................................. 129 Basic Interval Timer Mode Register Format .................................................................................. 131 Watchdog Timer Enable Flag (WDTM) Format ............................................................................. 132 Watch Timer Block Diagram ........................................................................................................... 139 Format of Watch Mode Register ..................................................................................................... 140 Timer/Event Counter (Channel 0) Block Diagram ......................................................................... 142 Timer/Event Counter (Channel 1) Block Diagram ......................................................................... 143 Timer/Event Counter (Channel 2) Block Diagram ......................................................................... 144 Timer/Event Counter Mode Register (Channel 0) Format ............................................................ 146 Timer/Event Counter Mode Register (Channel 1) Format ............................................................ 147 Timer/Event Counter Mode Register (Channel 2) Format ............................................................ 148 Timer/Event Counter Output Enable Flag Format ......................................................................... 149 Timer/Event Counter Control Register Format .............................................................................. 150 Timer/Event Counter Mode Register Setup ................................................................................... 152 Timer/Event Counter Control Register Setup ................................................................................ 155 Timer/Event Counter Output Enable Flag Setup ........................................................................... 155 Configuration of Timer/Event Counter ............................................................................................ 158 Count Operation Timing .................................................................................................................. 158 Configuration of Event Count .......................................................................................................... 160 Event Count Operation Timing ....................................................................................................... 161 Timer/Event Counter Mode Register Setup ................................................................................... 166 Timer/Event Counter Control Register Setup ................................................................................ 167 Configuration of PWM Pulse Generator ......................................................................................... 169 PWM Pulse Generator Operation Timing ...................................................................................... 169 Timer/Event Counter Mode Register Setup ................................................................................... 172 Timer/Event Counter Control Register Setup ................................................................................ 173 Timer/Event Counter Operation Configuration .............................................................................. 176 Count Operation Timing .................................................................................................................. 176 Event Count Operation Configuration ............................................................................................ 178 Event Count Operation Timing ....................................................................................................... 179 Timer/Event Counter Mode Register Setup (n = 1, 2) .................................................................. 185 Timer/Event Counter Output Enable Flag Setup ........................................................................... 186 Timer/Event Counter Control Register Setup ................................................................................ 186 Carrier Generator Operation Configuration ................................................................................... 189 Carrier Generator Operation Timing ............................................................................................... 190 Example of SBI System Configuration ........................................................................................... 204 Serial Interface Block Diagram ....................................................................................................... 205 Serial Operation Mode Register (CSIM) Format ........................................................................... 208 Serial Bus Interface Control Register (SBIC) Format ................................................................... 211 System Comprising Shift Register and Peripheral Devices Configuration .................................. 214 Example of System Configuration in 3-wire Serial I/O Mode ....................................................... 218 3-wire Serial I/O Mode Timing ........................................................................................................ 221 16 LIST OF FIGURES (3/4) Figure 5-65 5-66 5-67 5-68 5-69 5-70 5-71 5-72 5-73 5-74 5-75 5-76 5-77 5-78 5-79 5-80 5-81 5-82 5-83 5-84 5-85 5-86 5-87 5-88 5-89 5-90 5-91 5-92 5-93 5-94 5-95 5-96 5-97 5-98 5-99 5-100 5-101 5-102 5-103 5-104 5-105 5-106 5-107 5-108 Title Page Operation of RELT and CMDT ....................................................................................................... 222 Transfer Bit Change Circuit ............................................................................................................. 223 Example of System Configuration in 2-wire Serial I/O Mode ....................................................... 228 2-wire Serial I/O Mode Timing ........................................................................................................ 231 Operation of RELT and CMDT ....................................................................................................... 232 SBI System Configuration Example ............................................................................................... 235 SBI Transfer Timings ....................................................................................................................... 237 Bus Release Signal ......................................................................................................................... 238 Command Signal .............................................................................................................................. 238 Address ............................................................................................................................................. 239 Selecting Slave by Address ............................................................................................................ 239 Command ......................................................................................................................................... 240 Data ................................................................................................................................................... 240 Acknowledge Signal ......................................................................................................................... 241 Busy and Ready Signals ................................................................................................................. 242 RELT, CMDT, RELD, CMDD Operation (master) ......................................................................... 248 RELT, CMDT, RELD, CMDD Operation (slave) ............................................................................ 248 ACKT Operation ............................................................................................................................... 248 ACKE Operation ............................................................................................................................... 249 ACKD Operation .............................................................................................................................. 250 BSYE Operation ............................................................................................................................... 250 Pin Configuration ............................................................................................................................. 253 Address Transmission Operation from Master Device to Slave Device (when WUP = 1) ........ 255 Command Transmission Operation from Master Device to Slave Device .................................. 256 Data Transmission Operation from Master Device to Slave Device ........................................... 257 Data Transmission Operation from Slave Device to Master Device ........................................... 258 Example of Serial Bus Configuration ............................................................................................. 261 Transfer Format of READ Command ............................................................................................. 263 Transfer Formats of WRITE and END Commands ....................................................................... 264 Transfer Format of STOP Command ............................................................................................. 264 Transfer Format of STATUS Command ......................................................................................... 265 Status Format of STATUS Command ............................................................................................ 265 Transfer Format of RESET Command ........................................................................................... 266 Transfer Format of CHGMST Command ....................................................................................... 266 Operations of Master and Slave in Case of Error ......................................................................... 267 SCK/P01 Pin Configuration ............................................................................................................. 268 LCD Controller/Driver Block Diagram ............................................................................................ 270 Display Mode Register Format ....................................................................................................... 272 Format of Display Control Register ................................................................................................ 273 LCD/Port Selection Register Format .............................................................................................. 275 Data Memory Map ........................................................................................................................... 276 Relationship between Display Data Memory and Common Segments ....................................... 277 Common Signal Waveform (Static) ................................................................................................ 280 Common Signal Waveform (1/2 Bias method) .............................................................................. 280 17 LIST OF FIGURES (4/4) Figure 5-109 5-110 5-111 5-112 5-113 5-114 5-115 5-116 5-117 5-118 5-119 5-120 5-121 5-122 5-123 5-124 5-125 5-126 6-1 6-2 6-3 6-4 6-5 6-6 6-7 6-8 6-9 6-10 6-11 7-1 7-2 8-1 8-2 B-1 B-2 Title Page Common Signal Waveform (1/3 Bias method) .............................................................................. 280 Common and Segment Signal Electric Potentials and Phases ................................................... 281 LCD Drive Power Connection Examples (when split resistor is incorporated) ........................... 283 LCD Drive Power Connection Examples (when split resistor is connected externally) ............. 284 Static Mode LCD Display Pattern and Electrode Connection ...................................................... 285 Static LCD Panel Connection Example .......................................................................................... 286 Static LCD Drive Waveform Example ............................................................................................ 287 Division by 2 Mode LCD Display Pattern and Electrode Connection .......................................... 288 Division by 2 LCD Panel Connection Example ............................................................................. 289 Division by 2 LCD Drive Waveform Example (1/2 Bias method) ................................................. 290 Division by 3 Mode LCD Display Pattern and Electrode Connection .......................................... 291 Division by 3 LCD Panel Connection Example ............................................................................. 292 Division by 3 LCD Drive Waveform Example (1/2 Bias method) ................................................. 293 Division by 3 LCD Drive Waveform Example (1/3 Bias method) ................................................. 294 Division by 4 Mode LCD Display Pattern and Electrode Connection .......................................... 295 Division by 4 LCD Panel Connection Example ............................................................................. 296 Division by 4 LCD Drive Waveform Example (1/3 Bias method) ................................................. 297 Bit Sequential Buffer Format ........................................................................................................... 298 Interrupt Control Circuit Block Diagram ......................................................................................... 302 Interrupt Vector Table ...................................................................................................................... 304 Interrupt Priority Selection Register ............................................................................................... 307 Configurations of INT0, INT1, and INT4 ........................................................................................ 309 Noise Eliminator Input/Output Timing ............................................................................................ 310 Edge Detection Mode Register Format .......................................................................................... 311 Interrupt Processing Sequence ...................................................................................................... 313 Multiple Interrupts by Higher-Order Priority Interrupts .................................................................. 314 Multiple Interrupts by Changing Interrupt Status Flag .................................................................. 315 INT2 and KR0 to KR3 Block Diagram ............................................................................................ 330 Format of INT2 Edge Detection Mode Register (IM2) .................................................................. 331 Standby Mode Release Operation ................................................................................................. 337 Wait Time when STOP Mode is Released .................................................................................... 339 Configuration of Reset Function ..................................................................................................... 347 Reset Operation by RESET Signal Generation ............................................................................. 347 Package Drawing of EV-9200GC-64 (for reference only) ............................................................ 446 Recommended Footprint of EV-9200GC-64 (for reference only) ............................................... 447 18 LIST OF TABLES (1/2) Table 2-1 2-2 2-3 3-1 3-2 3-3 3-4 4-1 4-2 4-3 4-4 4-5 4-6 5-1 5-2 5-3 5-4 5-5 5-6 5-7 5-8 5-9 5-10 5-11 5-12 5-13 5-14 5-15 5-16 5-17 5-18 5-19 5-20 5-21 5-22 6-1 6-2 6-3 Title Pin Functions of Digital I/O Ports ................................................................................................... Pin Function of Pins Other Than Port Pins ................................................................................... List of Recommended Connections for Unused Pins ................................................................... Addressing Mode ............................................................................................................................. Register Bank Selected by RBE and RBS .................................................................................... Example of Using Different Register Banks for Normal Routine and Interrupt Routine ............ Addressing Modes Applicable to Operating Peripheral Hardware ............................................... Differences between Mk I Mode and Mk II Mode ......................................................................... Stack Area Selected by SBS .......................................................................................................... PSW Flags Saved and Restored during Stack Operation ............................................................ Carry Flag Manipulation Instructions .............................................................................................. Interrupt Status Flag Indication ....................................................................................................... RBE, RBS, and Selected Register Bank ....................................................................................... Types and Features of Digital Ports ............................................................................................... Page 27 29 41 47 59 60 64 71 85 89 90 91 93 96 I/O Pin Manipulation Instructions .................................................................................................... 105 Operation When I/O Port Is Manipulated ....................................................................................... 107 On-Chip Pull-Up Resistor Specification Method ............................................................................ 108 Maximum Time Required to Switch System to/from CPU Clocks ............................................... 124 Operation Modes of Timer/Event Counter ..................................................................................... 141 Resolution and Maximum Allowable Time Setting (8-bit timer mode) ......................................... 156 Resolution and Maximum Allowable Time Setting (16-bit timer mode) ....................................... 174 Selection of Serial Clock and Applications (in 3-wire serial I/O mode) ....................................... 222 Selection of Serial Clock and Applications (in 2-wire serial I/O mode) ....................................... 232 Selection of Serial Clock and Applications (in SBI mode) ........................................................... 247 Signal in SBI Mode .......................................................................................................................... 251 Maximum Number of Displayed Picture Elements ........................................................................ 271 Common Signal ................................................................................................................................ 278 LCD Drive Voltage (Static) .............................................................................................................. 279 LCD Drive Voltage (1/2 Bias method) ............................................................................................ 279 LCD Drive Voltage (1/3 Bias method) ............................................................................................ 279 LCD Drive Power Supply Values .................................................................................................... 282 S16 to S23 Pin Selection and Non-selection Voltage (Static Display Example) ........................ 285 S12 to S15 Pin Selection and Non-selection Voltage (Division by 2 Display Example) ............ 288 S6 to S8 Pin Selection and Non-selection Voltage (Division by 3 Display Example) ................ 291 S12, S13 Pin Selection and Non-selection Voltage (Division by 4 Display Example) ............... 295 Types of Interrupt Sources .............................................................................................................. 303 Set Signals for Interrupt Request Flags ......................................................................................... 306 IST1 and IST0 and Interrupt Processing Status ........................................................................... 312 19 LIST OF TABLES (2/2) Table 6-4 6-5 6-6 7-1 7-2 8-1 9-1 9-2 10-1 11-1 Title Page Identifying Interrupt Sharing Vector Table Address ...................................................................... 316 Types of Test Sources .................................................................................................................... 328 Set Signal for Test Request Flag ................................................................................................... 328 Operation Status in Standby Mode ................................................................................................ 335 Wait Time Selection by Using BTM ................................................................................................ 339 Status of Each Device After Reset ................................................................................................. 348 Pins Used to Write or Verify Program Memory ............................................................................. 351 Operation Mode ............................................................................................................................... 352 Selecting Mask Option of Pin ......................................................................................................... 357 Types of Bit Manipulation Addressing Modes and Specification Range ..................................... 360 20 CHAPTER 1 GENERAL The µPD753104, 753106,753108, and 75P3116 are 4-bit single-chip microcontrollers in the NEC’s 75XL Series, a successor to the 75X Series that boasts a wealth of variations. These four devices are called the µPD753108 Subseries as a general term. The µPD753108 is based on the existing µPD75308B, but has a higher ROM capacity and more sophisticated CPU functions, and can operate at high speeds at a voltage of as low as 1.8 V. In addition, the µPD753108 is also provided with an LCD controller/driver. This model is available in a small plastic QFP (12 × 12 mm) and is ideal for small application set that uses an LCD panel. The features of the µPD753108 are as follows: • Low-voltage operation: VDD = 1.8 to 5.5 V • Variable instruction execution time useful for high-speed operation and power saving 0.95 µs, 1.91 µs, 3.81 µs, 15.3 µs (at 4.19 MHz) 0.67 µs, 1.33 µs, 2.67 µs, 10.7 µs (at 6.0 MHz) 122 µs (at 32.768 kHz) • Five timer channels • Programmable LCD controller/driver • Small package (64-pin plastic QFP (12 × 12 mm)) The µPD75P3116 is provided with a one-time PROM that can be electrically written and is pin-compatible with the µPD753104, 753106, and 753108. This one-time PROM model is convenient for experimental development or small-scale production of an application system. Application Fields • Remote controllers • Camera-contained VCRs (camcoders) • Cameras • Gas meters, etc. Remark Unless otherwise specified, the µPD753108 is regarded as the representative model, and description throughout this manual is focused on this model. 21 CHAPTER 1 GENERAL 1.1 Functional Outline Parameter Function • 0.95, 1.91, 3.81, 15.3 µs (@ 4.19 MHz with main system clock) • 0.67, 1.33, 2.67, 10.7 µs (@ 6.0 MHz with main system clock) • 122 µ s (@ 32.768 kHz with subsystem clock) ROM 4096 × 8 bits (µ PD753104) 6144 × 8 bits (µ PD753106) 8192 × 8 bits (µ PD753108) 16384 × 8 bits (µ PD75P3116) RAM 512 × 4 bits • 4-bit operation: 8 × 4 banks • 8-bit operation: 4 × 4 banks 8 pins 20 pins 4 pins 32 pins 16/20/24 segments (can be changed to CMOS input/output port in 4-pin units; max. 8) • Display mode selection: Static, 1/2 duty (1/2 bias), 1/3 duty (1/2 bias), 1/3 duty (1/3 bias), 1/4 duty (1/3 bias) • On-chip split resistor for LCD drive can be specified by mask optionNote 2 • Segment selection: Of these, seven have software-specifiable on-chip pull-up resistors Twelve have software-specifiable on-chip pull-up resistors, and eight can also be used as segment outputs Each withstands up to 13 V and has a mask-option pull-up resistor Note 1 Instruction execution time On-chip memory General-purpose register Input/ output port CMOS input CMOS input/output N-ch open-drain input/output Total LCD controller/driver Timer 5 channels • 8-bit timer/event counter: 3 channels (Can also be used as a 16-bit timer/event counter, a carrier generator, or a gated timer) • Basic interval timer/watchdog timer: 1 channel • Watch timer: 1 channel • 3-wire serial I/O mode ... MSB or LSB can be selected for transferring first bit • 2-wire serial I/O mode • SBI mode 16 bits • Φ, 524, 262, 65.5 kHz (@ 4.19 MHz with main system clock) • Φ, 750, 375, 93.8 kHz (@ 6.0 MHz with main system clock) (@ 4.19 MHz with main system clock or @ 32.768 kHz with subsystem clock) • 2.93, 5.86, 46.9 kHz (@ 6.0 MHz with main system clock) External: 3, Internal: 5 External: 1, Internal: 1 • Ceramic or crystal oscillator for main system clock oscillation • Crystal oscillator for subsystem clock oscillation STOP/HALT mode V DD = 1.8 to 5.5 V • 64-pin plastic QFP (14 × 14 mm) • 64-pin plastic QFP (12 × 12 mm) • 2, 4, 32 kHz Serial interface Bit sequential buffer (BSB) Clock output (PCL) Buzzer output (BUZ) Vectored interrupt Test input System clock oscillator Standby function Power supply voltage Package Notes 1. The µPD75P3116 is not provided with the function to connect pull-up resistors by mask option. 2. The µPD75P3116 is not provided with a split resistor by mask option. 22 CHAPTER 1 GENERAL 1.2 Ordering Information Part Number Package 64-pin plastic QFP (14 × 14 mm, 0.8-mm pitch) 64-pin plastic QFP (12 × 12 mm, 0.65-mm pitch) 64-pin plastic QFP (14 × 14 mm, 0.8-mm pitch) 64-pin plastic QFP (12 × 12 mm, 0.65-mm pitch) 64-pin plastic QFP (14 × 14 mm, 0.8-mm pitch) 64-pin plastic QFP (12 × 12 mm, 0.65-mm pitch) 64-pin plastic QFP (14 × 14 mm, 0.8-mm pitch) 64-pin plastic QFP (12 × 12 mm, 0.65-mm pitch) Internal ROM Mask ROM Mask ROM Mask ROM Mask ROM Mask ROM Mask ROM One-time PROM One-time PROM µ PD753104GC-××× -AB8 µ PD753104GK-××× -8A8 µ PD753106GC-××× -AB8 µ PD753106GK-××× -8A8 µ PD753108GC-××× -AB8 µ PD753108GK-××× -8A8 µ PD75P3116GC-AB8 µ PD75P3116GK-8A8 Remark ××× indicates ROM code suffix. 1.3 Differences among µPD753108 Subseries Products Item µ PD753104 12 bits Mask ROM 4096 512 µ PD753106 13 bits Mask ROM 6144 µ PD753108 µ PD75P3116 14 bits Program counter Program memory (byte) Data memory (× 4 bits) Mask option of port 5 Wait time after RESET Mask ROM 8192 One-time PROM 16384 Pull-up resistor Available (specifiable to incorporate or not) Available (selectable from 2 17/fX and 215/f X) Note None (Cannot incorporate) None (Fixed to 215/fX) Note None (Cannot incorporate) P30/MD0 to P33/MD3 P50/D4 to P53/D7 P60/KR0/D0 to P63/KR3/D3 VPP Split resistor Available (specifiable to incorporate or not) for LCD driving Pin connection Pins 5 to 8 Pins 10 to 13 Pins 14 to 17 Pin 21 Other P30 to P33 P50 to P53 P60/KR0 to P63/KR3 IC Noise immunity and noise radiation differ because circuit scale and mask layout differ. Note The wait time after RESET becomes 21.8 ms at 6.0 MHz and 31.3 ms at 4.19 MHz if 217 /f X is selected; it becomes 5.46 ms at 6.0 MHz and 7.81 ms at 4.19 MHz if 2 15 /fX is selected. Caution There are differences in noise immunity and noise radiation between the PROM and mask ROM versions. When pre-producing an application set with the PROM version and then massproducing it with the mask ROM version, be sure to conduct sufficient evaluations for the commercial samples (not engineering samples) of the mask ROM version. 23 CHAPTER 1 GENERAL 1.4 Block Diagram BUZ/P23 Watch timer INTW fLCD Program counter CY ALU SBS BANK SP(8) 4 Port 0 4 Port 1 4 4 4 General registers Program memory (ROM)Note 1 4 4 Data memory (RAM) (512 × 4 bits) 4 Port 2 Port 3 Port 5 Port 6 Port 8 Port 9 4 P00 to P03 4 P10 to P13 4 4 4 4 4 4 P20 to P23 P30 to P33 (P30/MD0 to P33/MD3)Note 2 P50 to P53 (P50/D4 to P53/D7)Note 2 P60 to P63 (P60/D0 to P63/D3)Note 2 P80 to P83 P90 to P93 Basic interval timer/ watchdog timer INTBT TI0/P13 PTO0/P20 8-bit timer/event counter #0 INTT0 TOUT0 INTT1 TI1/TI2/ P12/INT2 PTO1/P21 PTO2/PCL /P22 8-bit timer/event Cascaded 16-bit counter #1 timer/ 8-bit event timer/event counter counter #2 Decode and control 16 4 LCD controller/driver 4 4 S0 to S15 S16/P93 to S19/P90 S20/P83 to S23/P80 COM0 to COM3 BIAS VLC0 VLC1 VLC2 SYNC/P31 INTT2 SI/SB1/P03 SO/SB0/P02 SCK/P01 Clocked serial interface INTCSI TOUT0 fX/2N CPU clock Φ Standby control fLCD INT1 INT0/P10 INT1/P11 INT4/P00 INT2/P12/ TI1/TI2 KR0/P60 to KR3/P63 System clock Clock output Clock generator control divider Main Sub Interrupt control 4 Bit-sequential. buffer (16) LCDCL/P30 PCL/PTO2/P22 X1 X2 XT1XT2 IC VDD (VPP)Note 2 VSS RESET Notes 1. Capacity of the ROM depends on the product. 2. The pin names or functions in parentheses applies with the µ PD75P3116. 24 CHAPTER 1 GENERAL 1.5 Pin Configuration (Top View) • 64-pin plastic QFP (14 × 14 mm) µ PD753104GC-××× -AB8, µ PD753106GC-××× -AB8 µ PD753108GC-××× -AB8, µ PD75P3116GC-AB8 • 64-pin plastic QFP (12 × 12 mm) µ PD753104GK-××× -8A8, µ PD753106GK-××× -8A8 µ PD753108GK-××× -8A8, µ PD75P3116GK-8A8 COM3 COM2 COM1 COM0 S10 50 64 63 62 61 60 59 58 57 56 55 54 53 52 51 BIAS VLC0 VLC1 VLC2 P30/LCDCL (/MD0) P31/SYNC (/MD1) P32 (/MD2) P33 (/MD3) VSS P50 (/D4) P51 (/D5) P52 (/D6) P53 (/D7) P60/KR0 (/D0) P61/KR1 (/D1) P62/KR2 (/D2) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 S11 S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 S12 S13 S14 S15 P93/S16 P92/S17 P91/S18 P90/S19 P83/S20 P82/S21 P81/S22 P80/S23 P23/BUZ P22/PCL/PTO2 P21/PTO1 P20/PTO0 RESET Note VDD P00/INT4 P01/SCK P02/SO/SB0 P03/SI/SB1 P10/INT0 P63/KR3 (/D3) P11/INT1 XT1 XT2 X1 X2 P12/INT2/TI1/TI2 Note Directly connect the IC (V PP ) pin to VDD. Remark The pin names or functions in parentheses applies with the µ PD75P3116. IC (VPP) P13/TI0 25 CHAPTER 1 GENERAL Pin Identification BIAS BUZ D0 to D7 IC INT2 KR0 to KR3 LCDCL MD0 to MD3 P00 to P03 P10 to P13 P20 to P23 P30 to P33 P50 to P53 P60 to P63 P80 to P83 : LCD Power Supply Bias Control : Buzzer Clock : Data Bus 0 to 7 : Internally Connected : External Test Input 2 : Key Return 0 to 3 : LCD Clock : Mode Selection 0 to 3 : Port 0 : Port 1 : Port 2 : Port 3 : Port 5 : Port 6 : Port 8 P90 to P93 PCL PTO0 to PTO2 RESET S0 to S23 SB0, SB1 SCK SI SO SYNC TI0 to TI2 VDD VLC0 to V LC2 VPP VSS X1, X2 XT1, XT2 : Port 9 : Programmable Clock : Programmable Timer Output 0 to 2 : Reset : Segment Output 0 to 23 : Serial Data Bus 0, 1 : Serial Clock : Serial Input : Serial Output : LCD Synchronization : Timer Input 0 to 2 : Positive Power Supply : LCD Power Supply 0 to 2 : Programming Power Supply : Ground : Main System Clock Oscillation 1, 2 : Subsystem Clock Oscillation 1, 2 COM0 to COM3 : Common Output 0 to 3 INT0, INT1, INT4 : External Vectored Interrupt 0, 1, 4 26 CHAPTER 2 PIN FUNCTION 2.1 Pin Functions of µPD753108 Table 2-1. Pin Functions of Digital I/O Ports (1/2) Alternate Function INT4 SCK SO/SB0 SI/SB1 INT0 INT1 TI1/TI2/INT2 TI0 Input/Output PTO0 PTO1 PCL/PTO2 BUZ Input/Output LCDCL (/MD0)Note 2 Programmable 4-bit input/output port (PORT3). SYNC (/MD1)Note 2 This port can be specified input/output bit-wise. (MD2)Note 2 On-chip pull-up resistor can be (MD3)Note 2 specified by software in 4-bit units. (D4)Note 2 (D5)Note 2 (D6)Note 2 (D7)Note 2 N-ch open-drain 4-bit input/output port (PORT5). Each pin withstands up to 13 V in open-drain mode. A pull-up resistor can be contained bitwise (mask option).Note 4 No Input E-B 4-bit input port (PORT1). On-chip pull-up resistors can be specified by software in 4-bit units. Noise eliminator can be selected in P10/INT0. 4-bit input/output port (PORT2). On-chip pull-up resistors can be specified by software in 4-bit units. No Input 8-bit I/O Circuit After Reset I/O TypeNote 1 No Input [B] [F]-A [F]-B [M]-C [B]-C Pin Name P00 P01 P02 P03 P10 P11 P12 P13 P20 P21 P22 P23 P30 P31 P32 P33 P50Note 3 P51Note 3 P52Note 3 P53Note 3 Input/Output Input Input/Output Input/Output Input/Output Input Function 4-bit input port (PORT0). For P01 to P03, on-chip pull-up resistors can be specified by software in 3-bit units. No Input E-B Input/Output No M-D High level (when pull- (M-E)Note 2 up resistors are provided) or highimpedance Notes 1. The circuit types enclosed with [ ] are Schmitt-triggered input circuits. 2. The pin names or functions in parentheses are available with the µPD75P3116. 3. If on-chip pull-up resistors are not specified by mask option (when used as N-ch open-drain input port), low level input leakage current increases when input or bit manipulation instruction is executed. 4. The µPD75P3116 is not provided with the function to connect pull-up resistors by mask option. 27 CHAPTER 2 PIN FUNCTION Table 2-1. Pin Functions of Digital I/O Ports (2/2) Pin Name P60 P61 P62 P63 P80 P81 P82 P83 P90 P91 P92 P93 Input/Output Input/Output Input/Output Input/Output Alternate Function KR0 (/D0)Note 2 KR1 (/D1)Note 2 Function Programmable 4-bit input/output port (PORT6). This port can be specified for input/output bit-wise. On-chip pull-up resistors can be specified by software in 4-bit units. 4-bit input/output port (PORT8). On-chip pull-up resistors can be specified by software in 4-bit units.Note 3 4-bit input/output port (PORT9). On-chip pull-up resistors can be specified by software in 4-bit units.Note 3 8-bit I/O Circuit After Reset I/O TypeNote 1 No Input [F]-A KR2 (/D2)Note 2 KR3 (/D3)Note 2 S23 S22 S21 S20 S19 S18 S17 S16 Yes Input H Input H Notes 1. The circuit types enclosed with [ ] are Schmitt-triggered input circuits. 2. The pin names or functions in parentheses are available with the µPD75P3116. 3. If these pins are used as segment outputs, do not enable the on-chip pull-up resistors for these pins by software. 28 CHAPTER 2 PIN FUNCTION Table 2-2. Pin Function of Pins Other Than Port Pins (1/2) Pin Name TI0 TI1 TI2 PTO0 PTO1 PTO2 PCL BUZ SCK SO/SB0 SI/SB1 INT4 INT0 Input Input Input/Output Output Input/Output Input P13 P12/INT2/TI2 P12/INT2/TI1 P20 P21 P22/PCL P22/PTO2 P23 P01 P02 P03 P00 P10 Clock output Optional frequency output (for buzzer output or system clock trimming) Serial clock input/output Serial data output Serial data bus input/output Serial data input Serial data bus input/output Edge detection vectored interrupt input (both rising edge and falling edge detection) Edge detection vectored interrupt input (detection edge can be selected). Noise eliminator can be selected in INT0/P10. Rising edge detection testable input Can select with noise eliminator or asynchronous Asynchronous Asynchronous Input Input Note 2 Input Input Note 2 — [B]-C [F]-A G-A H H G-B — Input [B]-C Input Input [F]-A [F]-B [M]-C [B] Timer/event counter output Input E-B Alternate Function event counter. Function Inputs external event pulses to the timer/ After Reset Input I/O Circuit TypeNote 1 [B]-C INT1 INT2 KR0 to KR3 S0 to S15 S16 to S19 S20 to S23 COM0 to COM3 VLC0 to VLC2 Input Input Output Output Output Output — P11 P12/TI1/TI2 P60 to P63 — P93 to P90 P83 to P80 — — Falling edge detection testable input Segment signal output Segment signal output Segment signal output Common signal output LCD drive power On-chip split resistor can be connected by mask option.Note 3 Notes 1. The circuit types enclosed with [ ] are Schmitt-triggered input circuits. 2. Each output selects the following V LCX as input source. S0 to S15: V LC1, COM0 to COM2: VLC2 , COM3: VLC0 3. The µPD75P3116 does not contain the mask options and a split resistor is not on-chip. 29 CHAPTER 2 PIN FUNCTION Table 2-2. Pin Function of Pins Other Than Port Pins (2/2) Pin Name BIAS LCDCL Note 3 SYNCNote 3 X1 Input/Output Output Output Output Input P30 P31 — Alternate Function — Function Output for external split resistor disconnect Clock output for externally expanded driver Clock output for externally expanded driver sync Crystal/ceramic connection pin for the main system clock oscillator. When inputting the external clock, input the external clock to pin X1, and the reverse phase of the external clock to pin X2. Crystal connection pin for the subsystem clock oscillator. When the external clock is used, input the external clock to pin XT1. In this case, input the reverse phase of clock to pin XT2. Pin XT1 can be used as a 1-bit input (test) pin. System reset input (low-level active) Provided only to the µPD75P3116. Select modes for writing/verifying program memory (PROM). Provided only to the µPD75P3116. Data bus pins during program memory (PROM) write/verify. After Reset Note 2 Input Input — I/O Circuit TypeNote 1 — E-B E-B — X2 — XT1 Input — — — XT2 — RESET MD0 to MD3 Input Input — P30 to P33 — Input [B] E-B D0 to D3 D4 to D7 IC VPP Input/Output P60/KR0 to P63/KR3 P50 to P53 Input Highimpedance — — [F]-A M-E — — — — — — Internally connected. Connect this pin directly to V DD. Provided only to the µPD75P3116. Supplies voltage necessary for writing/ verifying program memory (PROM). Directly connect this pin to V DD for normal operation. Apply +12.5 V to this pin to write/verify PROM. Positive power supply Ground potential VDD VSS — — — — — — — — Notes 1. The circuit types enclosed with [ ] are Schmitt-triggered input circuits. 2. When a split resistor is contained .......... Low level When no split resistor is contained ........ High-impedance 3. These pins are provided for future system expansion. At present, these pins are used only as pins P30 and P31. 30 CHAPTER 2 PIN FUNCTION 2.2 Pin Functions 2.2.1 P00 to P03 (PORT0) ··· input shared with INT4, SCK, SO/SB0, and SI/SB1 P10 to P13 (PORT1) ··· input shared with INT0, INT1, INT2/TI1/TI2, and TI0 These pins are 4-bit input ports. These pins have the following functions, in addition to the input port function. • • Port 0 : Vectored interrupt input (INT4) Serial interface I/Os (SCK, SO/SB0, SI/SB1) Port 1 : Vectored interrupt inputs (INT0, INT1) Edge detection test input (INT2) External event pulse input to timer/event counter (TI0 to TI2) The alternate function pin of port 0 is provided with the output function depending on the operation mode when port 0 uses serial interface function. Each pin of port 0 and port 1 is Schmitt trigger input pins to prevent malfunctioning due to noise. In addition, the P10 pin can select a noise eliminator (for details, refer to 6.3 (3) Hardware of INT0, INT1, and INT4). Software enables port 0 in 3-bit units (P01 to P03) and port 1 in 4-bit units (P10 to P13) to connect with on-chip pull-up resistors. Whether or not the on-chip pull-up resistors are connected is specified by using the pull-up resistor specification register group A (POGA). When the RESET signal is asserted, all the pins are set in the input mode. 31 CHAPTER 2 PIN FUNCTION 2.2.2 P20 to P23 (PORT2) ··· I/O shared with PTO0 to PTO2, PCL, and BUZ P30 to P33 (PORT3) ··· I/O shared with LCDCL, SYNC, and MD0 to MD3Note P50 to P53 (PORT5) ··· N-ch open-drain, medium voltage (13 V), I/O shared with D4 to D7Note P60 to P63 (PORT6) ··· I/O shared with KR0 to KR3 and D0 to D3Note P80 to P83 (PORT8) and P90 to P93 (PORT9) ··· I/O shared with S23 to S20 and S19 to S16 These pins are 4-bit I/O ports with output latch. In addition to the I/O port function, ports share the following functions. • Port 2 : Timer/event counter outputs (PTO0 to PTO2) Clock output (PCL) Any frequency output (BUZ) • Port 3 : Clock for driving external expansion LCD driver (LCDCL) Clock for synchronizing external expansion LCD driver (SYNC) Mode selection (MD0 to MD3) Note of program memory (PROM) write/verify • • • Port 5 Port 6 : Data bus (D4 to D7) Note of program memory (PROM) write/verify : Key interrupt input (KR0 to KR3) Data bus (D0 to D3) Note of program memory (PROM) write/verify Ports 8 and 9 : Segment signal outputs (S23 to S20 and S19 to S16) Note Alternate function pin only in the µ PD75P3116. Port 5 is an N-ch open-drain, medium-voltage (13 V) port. Input/output mode selection of each port is set by the port mode register. Ports 2, 5, 8, and 9 can be set in input or output mode in 4-bit units, and ports 3 and 6 can be set in input or output mode in 1-bit units. Ports 2, 3, 6, 8, and 9 can be connected with on-chip pull-up resistors in 4-bit units via software, by manipulating the pull-up resistor specification register group A and B (POGA and POGB). Port 5 can be connected with a pullup resistor in 1-bit units by mask option. However, the µPD75P3116 is not provided with a pull-up resistor by mask option. Ports 8 and 9 can be set in input or output mode in pairs in 8-bit units. When the RESET signal is asserted, ports 2, 3, 6, 8, and 9 are set in input mode (high impedance), and port 5 is set at the high-level (when the pullup resistor of mask option is connected) or high-impedance state. 2.2.3 TI0 to TI2 ··· inputs shared with port 1 These are the external event pulse input pins of timers/event counters 0 through 2. These pins become effective by selecting the external event pulse input for the count pulse (CP) with the timer/ event counter mode register (TM0, TM1, TM2). TI0 through TI2 are Schmitt trigger input pins. Refer to 5.5.1 (1) Timer/event counter mode register (TM0, TM1, TM2). 32 CHAPTER 2 PIN FUNCTION 2.2.4 PTO0 to PTO2 ··· outputs shared with port 2 These are the output pins of timers/event counters 0 through 2, and output square wave pulses. To output the signal of a timer/event counter, clear the output latch of the corresponding pin of port 2 to “0”, and set the bit corresponding to port 2 of the port mode register to “1” to set the output mode. The outputs of these pins are cleared to “0” by the timer start instruction. Refer to 5.5.2 (3) Timer/event counter operation. 2.2.5 PCL ··· output shared with port 2 This is a programmable clock output pin and is used to supply the clock to a peripheral LSI (such as a slave microcomputer). When the RESET signal is asserted, the contents of the clock output mode register (CLOM) are cleared to “0”, disabling the output of the clock. In this case, the PCL pin can be used as an ordinary port pin. Refer to 5.2.4 Clock output circuit. 2.2.6 BUZ ··· output shared with port 2 This is a frequency output pin and is used to issue a buzzer sound or trim the system clock frequency by outputting a specified frequency (2, 4, or 32 kHz: 4.19 MHz of main system clock or 32.768 kHz of subsystem clock). This bit is valid only when the bit 7 (WM7) of the watch mode register (WM) is set to “1”. When the RESET signal is asserted, WM7 is cleared to 0, so that the BUZ pin is used as an ordinary port pin. Refer to 5.4.2 Watch mode register. 2.2.7 SCK, SO/SB0, and SI/SB1 ··· 3-state I/Os shared with port 0 These are serial interface I/O pins and operate in accordance with the setting of the serial operation mode register (CSIM). When 3-wire serial I/O mode is selected, SCK functions as the CMOS I/O, SO functions as the CMOS output, and SI functions as the CMOS input. When 2-wire serial I/O mode or SBI mode is selected, SCK functions as the CMOS I/O, and SB1 (SB0) functions as the N-ch open-drain I/O. When the RESET signal is asserted, the serial interface operation is stopped, and these pins served as input port pins. All these pins are Schmitt trigger input pins. Refer to 5.6 Serial Interface. 2.2.8 INT4 ··· input shared with port 0 This is an external vectored interrupt input pin and becomes active at both the rising and falling edges. When the signal input to this pin changes from high to low level or vice versa, the interrupt request flag is set. INT4 is an asynchronous input pin and the interrupt is acknowledged when a high-level or low-level signal is input to this pin for a fixed time, regardless of the operating clock of the CPU. INT4 can also be used to release the STOP and HALT modes. This pin is a Schmitt trigger input pin. 33 CHAPTER 2 PIN FUNCTION 2.2.9 INT0 and INT1 ··· inputs shared with port 1 These pins input interrupt signals that are detected by the edge. INT0 has a function to select a noise eliminator. The edge can be selected by using the edge detection mode registers (IM0 and IM1). (1) INT0 (bits 0 and 1 of IM0) (a) Active at rising edge (b) Active at falling edge (c) Active at both rising and falling edges (d) External interrupt signal input disabled (2) INT1 (bit 0 of IM1) (a) Active at rising edge (b) Active at falling edge INT0 is an asynchronous input pin. The signal input to this pin is acknowledged as long as the signal has a specific high-level width, regardless of the operating clock of the CPU. Beside that, a noise eliminator can be added with software. Two levels of the sampling clock for noise elimination are provided. The acknowledged signal width differs depending on the CPU operating clock. INT1 is an asynchronous input pin. The signal input to this pin is acknowledged as long as the signal has a specific high-level width, regardless of the operating clock of the CPU. When the RESET signal is asserted, IM0 and IM1 are cleared to “0”, and the rising edge is selected as the active edge. Both INT0 and INT1 can be used to release the STOP and HALT modes. However, when the noise eliminator is selected, INT0 cannot be used to release the STOP and HALT modes. INT0 and INT1 are Schmitt trigger input pins. 2.2.10 INT2 ··· input shared with port 1 This pin inputs an external test signal that is active at the rising edge. When INT2 is selected by the edge detection mode register (IM2), and when the signal input to this pin goes low, an internal test flag (IRQ2) is set. INT2 is an asynchronous input pin. The signal input to this pin is acknowledged as long as the signal has a specific high-level width, regardless of the operating clock of the CPU. When the RESET signal is asserted, the contents of IM2 are cleared to “0”, and the test flag (IRQ2) is set at the rising edge of the INT2 pin. INT2 can be used to release the STOP and HALT modes. INT2 is a Schmitt trigger input pin. 34 CHAPTER 2 PIN FUNCTION 2.2.11 KR0 to KR3 ··· inputs shared with port 6 These are key interrupt input pins, which input interrupt signals that are detected in parallel at falling edge. The interrupt source can be selected from “KR2 and KR3” and “KR0 to KR3” by using the edge detection mode register (IM2). When the RESET signal is asserted, these pins serve as port 6 pins and set in input mode. 2.2.12 S0 to S23 ··· outputs These are segment signal output pins that can directly drive the segment pins (front panel electrodes) of an LCD and perform static and 2- or 3-time division drive of the 1/2 bias method or 3- or 4-time division drive of the 1/3 bias method. S16 through S19 and S20 through S23 are shared with ports 9 and 8, respectively, and the modes of these pins can be selected by using display mode register (LCDM). 2.2.13 COM0 to COM3 ··· outputs These are common signal output pins that can directly drive the common pins (rear panel electrodes) of an LCD. They output common signals at static (COM0, 1, 2, and 3 outputs), 2-time division drive of the 1/2 bias method (COM0 and 1 outputs) or 3-time division drive (COM0, 1, and 2 outputs), or 3-time division drive of the 1/3 bias method (COM0, 1, and 2 outputs) or 4-time division drive (COM0, 1, 2, and 3 outputs). 2.2.14 VLC0 to VLC2 These are power supply pins to drive an LCD. With the µ PD753108, a split resistor can be internally connected to the V LC0 through VLC2 pins by mask option, so that power to drive the LCD in accordance with each bias method can be supplied without an external split resistor. The µ PD75P3116 does not have a mask option and is not provided with a split resistor. 2.2.15 BIAS This is an output pin for dividing resistor cutting. It is connected to the VLC0 pin to supply various types of LCD driving voltages and is used to change a resistance division ratio, connect an external resistor along with the VCL0 through VCL2 pins and V SS pin, and fine-tune the LCD driving supply voltage. 2.2.16 LCDCL This is a clock output pin for driving an external LCD expansion driver. 2.2.17 SYNC This is a clock output pin to synchronize an external LCD expansion driver. 35 CHAPTER 2 PIN FUNCTION 2.2.18 X1 and X2 These pins connect a crystal/ceramic oscillator for main system clock oscillation. An external clock can also be input to these pins. (a) Crystal/ceramic oscillation VDD (b) External clock µ PD753108 External clock X1 µ PD753108 X1 X2 VDD Crystal or ceramic resonator (4.194304 MHz typ.) X2 2.2.19 XT1 and XT2 These pins connect a crystal oscillator for subsystem clock oscillation. An external clock can also be input to these pins. (a) Crystal oscillation VDD (b) External clock µ PD753108 External clock XT1 µ PD753108 XT1 XT2 VDD Crystal resonator (32.768 kHz typ.) XT2 Remark Refer to paragraph 5.2.2 (6) when the subsystem clock is not used. 2.2.20 RESET This pin inputs a low-active RESET signal. The RESET signal is an asynchronous input signal and is asserted when a signal with a specific low-level width is input to this pin regardless of the operating clock. The RESET signal takes precedence over all the other operations. This pin can be used to initialize and start the CPU, but also to release the STOP and HALT modes. The RESET pin is a Schmitt trigger input pin. 36 CHAPTER 2 PIN FUNCTION 2.2.21 MD0 to MD3 (µ PD75P3116 only) ··· inputs/outputs shared with port 3 These pins are provided to the µPD75P3116 only, and are used to select a mode when the program memory (one-time PROM) is written or verified. 2.2.22 D0 to D7 (µ PD75P3116 only) ··· inputs/outputs shared with ports 5 and 6 These pins are provided to the µ PD75P3116 only, and are used as data bus pins when the program memory (one-time PROM) is written or verified. 2.2.23 IC (µ PD753104, 753106, and 753108 only) The IC (Internally Connected) pin sets a test mode in which the µPD753108 is tested before shipment. It is usually best to connect the IC pin directly to the VDD pin with as short a wiring length as possible. If a voltage difference is generated between the IC and VDD pins because the wiring length between the IC and VDD pins is too long, or because external noise is superimposed on the IC pin, your program may not be correctly executed. • Directly connect the IC pin to the V DD pin. Keep as short as possible. VDD IC (VPP) VDD 2.2.24 VPP (µ PD75P3116 only) This pin inputs a program voltage when the program memory (one-time PROM) is written or verified. It is usually best to connect this pin directly to the VDD (refer to the figure above). Apply 12.5 V to this pin when the PROM is written or verified. 2.2.25 VDD Positive power supply pin. 2.2.26 GND. VSS 37 CHAPTER 2 PIN FUNCTION 2.3 Pin Input/Output Circuits The µ PD753108 pin input/output circuits are shown schematically. (1/3) TYPE A TYPE D VDD VDD data P-ch IN N-ch output disable N-ch P-ch OUT CMOS specification input buffer. TYPE B Push-pull output that can be placed in output high-impedance (both P-ch, N-ch off). TYPE E-B VDD P.U.R. P.U.R. enable data Type D output disable P-ch IN IN/OUT Schmitt trigger input having hysteresis characteristic. Type A P.U.R. : Pull-Up Resistor TYPE B-C VDD TYPE F-A VDD P.U.R. P.U.R. P.U.R. enable P.U.R. enable data output disable IN Type B Type D P-ch P-ch IN/OUT P.U.R. : Pull-Up Resistor P.U.R. : Pull-Up Resistor 38 CHAPTER 2 PIN FUNCTION (2/3) TYPE F-B VDD P.U.R. P.U.R enable output disable (P) data output disable output disable (N) N-ch data output disable TYPE E-B VDD P-ch IN/OUT P-ch SEG data IN/OUT TYPE G-A TYPE H P.U.R. : Pull-Up Resistor TYPE G-A VLC0 P.U.R. enable P-ch N-ch TYPE M-C VDD P.U.R. P-ch IN/OUT data output disable N-ch VLC2 N-ch P.U.R. : Pull-Up Resistor TYPE G-B TYPE M-D P.U.R. (Mask Option) VLC0 data VLC1 P-ch N-ch output disable input instruction N-ch (+13 V withstand voltage) IN/OUT VDD VLC1 OUT SEG data N-ch VDD P-ch P.U.R. OUT COM data N-ch VLC2 N-ch P-ch Note Voltage limitation circuit (+13 V withstand voltage) Note Pull-up resistor that operates only when an input instruction is executed if on-chip pull-up resistors are not specified by mask option (current flows from VDD to the pin when the pin is low). 39 CHAPTER 2 PIN FUNCTION (3/3) TYPE M-E IN/OUT data output disable VDD input instruction P-ch P.U.R. Note N-ch (+13 V withstand voltage) Voltage limitation Voltage circuit controller (+13 V withstand voltage) Note Pull-up resistor that operates only when an input instruction is executed (current flows from VDD to the pin when the pin is low). 40 CHAPTER 2 PIN FUNCTION 2.4 Recommended Connections for Unused Pins Table 2-3. List of Recommended Connections for Unused Pins Pin Recommended Connection Connect to V SS or VDD. Connect to V SS or VDD individually via resistor. P00/INT4 P01/SCK P02/SO/SB0 P03/SI/SB1 P10/INT0 P11/INT1 P12/TI1/TI2/INT2 P13/TI0 P20/PTO0 P21/PTO1 P22/PCL/PTO2 P23/BUZ P30/LCDCL (/MD0) Note 1 P31/SYNC (/MD1) Note 1 P32 (/MD2) Note 1 P33 (/MD3) Note 1 P50 (/D4) Note 1 P51 (/D5) Note 1 Connect to V SS. Connect to V SS or VDD. Input state : Connect to VSS or VDD individually via resistor. Output state : Leave open. Connect to V SS (Do not connect pull-up resistor by mask option). P52 (/D6) Note 1 P53 (/D7) Note 1 P60/KR0 (/D0) Note 1 P61/KR1 (/D1) Note 1 Input state : Connect to VSS or VDD individually via resistor. Output state : Leave open. P62/KR2 (/D2) Note 1 P63/KR3 (/D3) Note 1 S0 to S15 COM0 to COM3 S16/P93 to S19/P90 S20/P83 to S23/P80 V LC0 to VLC2 BIAS XT1 Note 2 XT2 Note 2 IC (VPP) Note 1 Input state : Connect to VSS or VDD individually via resistor. Output state : Leave open. Connect to V SS. Only if all of V LC0 to VLC2 are unused, connect to VSS. In other cases, leave open. Connect to V SS or VDD. Leave open. Connect directly to V DD. Leave open. Notes 1. ( ): µ PD75P3116 only 2. When not using the subsystem clock, select SOS.0 = 1 (the on-chip feedback resistor is not used). 41 [MEMO] 42 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP The 75XL architecture employed for the µPD753108 has the following features: • Internal RAM: 4K words × 4 bits MAX. (12-bit address) • Expandability of peripheral hardware To realize these superb features, the following methods are employed: (1) Bank configuration of data memory (2) Bank configuration of general-purpose registers (3) Memory mapped I/O This chapter describes each of these features. 3.1 3.1.1 Bank Configuration of Data Memory and Addressing Mode Bank configuration of data memory The µPD753108 is provided with static RAM at the addresses 000H through 1FFH of the data memory space, of which a 24 × 4 bit area of addresses 1E0H through 1F7H can also be used as a display data memory. Peripheral hardware units (such as I/O ports and timers) are allocated to addresses F80H through FFFH. The µPD753108 employs memory bank configuration that directly or indirectly specifies the lower 8 bits of an address by an instruction and the higher 4 bits of the address by a memory bank when the data memory space of 12-bit address (4K words × 4 bits) is addressed. To specify a memory bank (MB), the following hardware units are provided: • Memory bank enable flag (MBE) • Memory bank selection register (MBS) MBS is a register that selects a memory bank. Memory bank 0, 1, or 15 can be selected. MBE is a flag that enables or disables the memory bank selected by MBS. When MBE is 0, the specified memory bank (MB) is fixed, regardless of MBS, as shown in Figure 3-1. When MBE is 1, however, a memory bank is selected according to the setting of MBS, so that the data memory space can be expanded. To address the data memory space, MBE is usually set to 1 and the data memory of the memory bank specified by MBS is manipulated. By selecting a mode of MBE = 0 or a mode of MBE = 1 for each processing of the program, programming can be efficiently carried out. Adapted Program Processing MBE = 0 mode • Interrupt processing • Processing repeating internal hardware manipulation and stack RAM manipulation • Subroutine processing MBE = 1 mode • Normal program processing Effect Saving/restoring MBS unnecessary Changing MBS unnecessary Saving/restoring MBS unnecessary 43 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP Figure 3-1. Selecting MBE = 0 Mode and MBE = 1 Mode (Main program) SET1 MBE MBE =1 (Subroutine) CLR1 MBE MBE = 0 CLR1 MBE Internal hardware and static RAM manipulation repeated MBE =0 SET1 MBE RET (Interrupt processing) ; MBE = 0 by vector table MBE = 0 MBE =1 RETI Remark Solid line: MBE = 1, dotted line: MBE = 0 Because MBE is automatically saved or restored during subroutine processing, it can be changed even while subroutine processing is under execution. MBE can also be saved or restored automatically during interrupt processing, so that MBE during interrupt processing can be specified as soon as the interrupt processing is started, by setting the interrupt vector table. This feature is useful for high-speed interrupt processing. To change MBS by using subroutine processing or interrupt processing, save or restore it to stack by using the PUSH or POP instruction. MBE is set by using the SET1 or CLR1 instruction. Use the SEL instruction to set MBS. Examples 1. To clear MBE and fix memory bank CLR1 SET1 SEL MBE MBE MB1 ; MBE ← 0 ; MBE ← 1 ; MBS ← 1 2. To select memory bank 1 44 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP 3.1.2 Addressing mode of data memory The 75XL architecture employed for the µ PD753108 provides the seven types of addressing modes as shown in Table 3-1, so that the data memory space can be efficiently addressed by the bit length of the data to be processed, and so that programming can be carried out efficiently. (1) 1-bit direct addressing (mem.bit) This mode is for directly addressing each bit of the entire data memory space by using the operand of an instruction. The memory bank (MB) to be specified is fixed to 0 in the mode of MBE = 0 if the address specified by the operand ranges from 00H to 7FH, and to 15 if the address specified by the operand is 80H to FFH. In the mode of MBE = 0, therefore, both the data area of addresses 000H through 07FH and the peripheral hardware area of F80H through FFFH can be addressed. In the mode of MBE = 1, MB = MBS; therefore, the entire data memory space can be addressed. This addressing mode can be used with four instructions: bit set and reset (SET1 and CLR1) instructions, and bit test instructions (SKT and SKF). Example To set FLAG1, reset FLAG2, and test whether FLAG3 is 0 FLAG1 FLAG2 FLAG3 EQU EQU EQU SET1 SEL SET1 CLR1 SKF 03FH.1 087H.2 0A7H.0 MBE MB0 FLAG1 FLAG2 FLAG3 ; Bit 1 of address 3FH ; Bit 2 of address 87H ; Bit 3 of address A7H ; MBE ← 1 ; MBS ← 0 ; FLAG1 ← 1 ; FLAG2 ← 0 ; FLAG3 = 0? 45 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP Figure 3-2. Data Memory Configuration and Addressing Range for Each Addressing Mode Addressing mode Memory bank enable flag 000H General purpose register area 01FH 020H 07FH 080H Data area Static RAM (memory bank 0) 0FFH 100H Data area Static RAM (memory bank 1) 1DFH 1E0H Display data memory 1F7H 1F8H 1FFH Not contained F80H FB0H FBFH FC0H Peripheral hardware area (memory bank 15) FF0H FFFH Remark –: don’t care



,, 



 ,,



 ,,  

,,, 
 ,,


  ,


, ,, 
 ,  ,

,,,, ,
 
,
, 
 
, ,

, 

 
 , mem mem. bit @HL @H+mem. bit @DE @DL Stack addressing fmem. bit pmem. @L MBE=0 MBE=1 MBE=0 MBE=1 — — — — MBS =0 MBS =0 SBS =0 MBS =1 MBS =1 SBS =1 MBS =15 MBS =15 46 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP Table 3-1. Addressing Mode Addressing Mode 1-bit direct addressing Identifier mem.bit Specified Address Bit of address indicated by MB and mem. The bit is addressed by “bit”. • When MBE = 0 when mem = 00H-7FH : MB = 0 when mem = 80H-FFH : MB = 15 • When MBE = 1 : MB = MBS Address indicated by MB and mem. • When MBE = 0 when mem = 00H-7FH : MB = 0 when mem = 80H-FFH : MB = 15 • When MBE = 1 8-bit direct addressing Address indicated by MB • When MBE = 0 when mem = 00H-7FH when mem = 80H-FFH • When MBE = 1 @HL @HL+ @HL– @DE @DL 8-bit register indirect addressing Bit manipulation addressing @HL fmem.bit : MB = MBS and mem (mem is an even address). : MB = 0 : MB = 15 : MB = MBS 4-bit direct addressing mem 4-bit register indirect addressing Address indicated by MB and HL. MB = MBE • MBS Address indicated by MB and HL. MB = MBE • MBS When HL+ is given, L register is automatically incremented after addressing. When HL– is given, L register is automatically decremented after addressing. Memory bank 0 address indicated by DE. Memory bank 0 address indicated by DL. Address indicated by MB and HL (L register contents are even). MB = MBE • MBS. Bit of address indicated by fmem. The bit is addressed by “bit”. fmem = FB0H-FBFH (hardware related to interrupt) FF0H-FFFH (I/O port) Bit of address indicated by high-order 10-bit of pmem and high-order 2-bit of L register. The bit is addressed by low-order 2-bit of L register. pmem = FC0H-FFFH Bit of address indicated by MB, H, and low-order 4-bit of mem. The bit is addressed by “bit”. MB = MBE•MBS The address indicated by SP of memory banks 0 and 1 selected by setting SBS. pmem.@L @H+mem.bit Stack addressing — 47 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP (2) 4-bit direct addressing (mem) This addressing mode is to directly address the entire memory space in 4-bit units by using the operand of an instruction. Like the 1-bit direct addressing mode, the area that can be addressed is fixed to the data area of addresses 000H through 07FH and the peripheral hardware area of F80H through FFFH in the mode of MBE = 0. In the mode of MBE = 1, MB = MBS, and the entire data memory space can be addressed. This addressing mode is applicable to the MOV, XCH, INCS, IN, and OUT instructions. Caution If data related to I/O ports is stored to the stack RAM in bank 1 as shown in Example 1 below, the program efficiency is degraded. To program without changing MBS as shown in Example 2, store the data related to I/O ports to the addresses 00H through 7FH of bank 0. Examples 1. To output data of “BUFF” to port 5 BUFF EQU SET1 SEL MOV SEL OUT 11AH MBE MB1 A, BUFF MB15 PORT5, A ; “BUFF” is at address 11AH ; MBE ← 1 ; MBS ← 1 ; A ← (BUFF) ; MBS ← 15 ; PORT5 ← A 2. To input data from port 5 and store it to “DATA1” DATA1 EQU CLR1 IN MOV 5FH MBE A, PORT5 DATA1, A ; “DATA1” is at address 5FH ; MBE ← 0 ; A ← PORT5 ; (DATA1) ← A 48 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP (3) 8-bit direct addressing (mem) This addressing mode is for directly addressing the entire data memory space in 8-bit units by using the operand of an instruction. The address that can be specified by the operand is an even address. The 4-bit data of the address specified by the operand and the 4-bit data of the address higher than the specified address are used in pairs and processed in 8-bit units by the 8-bit accumulator (XA register pair). The memory bank that is addressed is the same as that addressed in the 4-bit direct addressing mode. This addressing mode is applicable to the MOV, XCH, IN, and OUT instructions. Examples 1. To transfer the 8-bit data of ports 8 and 9 to addresses 20H and 21 DATA EQU CLR1 IN MOV 020H MBE XA, PORT8 DATA, XA ; MBE ← 0 ; X ← port 9, A ← port 8 ; (21H) ← X, (20H) ← A 2. To load the 8-bit data input to the shift register (SIO) of the serial interface and, at the same time, set transfer data to instruct the start of transfer SEL XCH MB15 XA, SIO ; MBS ← 15 ; XA ↔ (SIO) 49 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP (4) 4-bit register indirect addressing (@rpa) This addressing mode is for indirectly addressing the data memory space in 4-bit units by using a data pointer (a pair of general-purpose registers) specified by the operand of an instruction. As the data pointer, three register pairs can be specified: HL that can address the entire data memory space by using MBE and MBS, and DE and DL that always address memory bank 0, regardless of the specification by MBE and MBS. By selecting a register pair depending on the data memory bank to be used, programming can be carried out efficiently. Example To transfer data 50H through 57H to addresses 110H through 117H DATA1 DATA2 EQU EQU SET1 SEL MOV MOV LOOP: MOV XCH DECS BR 57H 117H MBE MB1 D, #DATA1 SHR 4 HL, #DATA2 AND 0FFH A, @DL A, @HL L LOOP ; HL ← 17H ; A ← (DL) ; A ← (HL) ;L←L–1 The addressing mode that uses register pair HL as the data pointer is widely used to transfer, operate, compare, and input/output data. The addressing mode using register pair DE or DL is used with the MOV and XCH instructions. By using this addressing mode in combination with the increment/decrement instruction of a general-purpose register or a register pair, the addresses of the data memory can be updated as shown in Figure 3-3. 50 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP Examples 1. To compare data 50H through 57H with data 110H through 117H DATA1 DATA2 EQU EQU SET1 SEL MOV MOV LOOP: MOV SKE BR DECS BR 57H 117H MBE MB1 D, #DATA1 SHR 4 HL, #DATA2 AND 0FFH A, @DL A, @HL NO L LOOP ; A = (HL)? ; NO ; YES, L ← L – 1 2. To clear data memory of 00H through FFH CLR1 CLR1 MOV MOV LOOP: MOV INCS BR INCS BR RBE MBE XA, #00H HL, #04H @HL, A L LOOP H LOOP ; H ← H+1 ; (HL) ← A ; L ← L+1 51 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP Figure 3-3. Static RAM Address Update Method X0H 0XH DECS D DECS D XFH DECS E DECS L @DL 4-bit transfer INCS L DECS DE @DE 4-bit transfer INCS E INCS DE INCS D Direct addressing bit manipulation 4-bit transfer 8-bit transfer INCS D DECS H DECS H Auto decrement DECS L DECS HL @HL 4-bit manipulation 8-bit manipulation Auto increment INCS L INCS HL @H+mem. bit Bit manipulation INCS H INCS H FXH 52 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP (5) 8-bit register indirect addressing (@HL) This addressing mode is to indirectly address the entire data memory space in 8-bit units by using a data pointer (HL register pair). In this addressing mode, data is processed in 8-bit units, that is, the 4-bit data at an address specified by the data pointer with bit 0 (bit 0 of the L register) cleared to 0 and the 4-bit data at the address higher are used in pairs and processed with the data of the 8-bit accumulator (XA register). The memory bank to be specified turns MB = MBE • MBS, which is the same case the HL register is specified in the 4-bit register indirect addressing mode. This addressing mode is applicable to the MOV, XCH, and SKE instructions. Examples 1. To compare whether the count register (T0) value of timer/event counter 0 is equal to the data at addresses 30H and 31H DATA EQU CLR1 MOV MOV SKE BR INCS MOV SKE 30H MBE HL, #DATA XA, T0 A, @HL NO L A, X A, @HL ;A←X ; A = (HL)? ; XA ← count register 0 ; A = (HL)? 2. To clear data memory at 00H through FFH CLR1 CLR1 MOV MOV LOOP: MOV INCS INCS BR INCS BR RBE MBE XA, #00H HL, #04H @HL, XA L L LOOP H LOOP ; (HL) ← XA 53 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP (6) Bit manipulation addressing This addressing mode is used to perform the bit manipulation to each bit in the entire memory space (such as Boolean processing and bit transfer). While the 1-bit direct addressing mode can be only used with the instructions that set, reset, or test a bit, this addressing mode can be used in various ways, such as Boolean processing by the AND1, OR1, and XOR1 instructions, and test and reset by the SKTCLR instruction. Bit manipulation addressing can be implemented in the following three ways, which can be selected depending on the data memory address to be used. (a) Specific address bit direct addressing (fmem.bit) This addressing mode is to manipulate the hardware units that use bit manipulation especially often, such as I/O ports and interrupt-related flags, regardless of the setting of the memory bank. Therefore, the data memory addresses to which this addressing mode is applicable are FF0H through FF9H, to which the I/ O ports are mapped, and FB0H through FBH, to which the interrupt-related hardware units are mapped. The hardware units in these two data memory areas can be manipulated in bit units at any time in the direct addressing mode, regardless of the setting of MBS and MBE. Examples 1. To test timer 0 interrupt request flag (IRQT0) and, if it is set, clear the flag and reset P63 SKTCLR BR CLR1 IRQT0 NO PORT6.3 ; IRQT0 = 1? ; NO ; YES 54 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP Examples 2. To reset P53 if both P30 and P51 pins are 1 P30 P51 P53 (i) SET1 AND1 AND1 SKT BR CLR1 . . . SETP: SET1 . . . SKT BR SKT BR CLR1 . . . SETP: SET1 CY CY, PORT3.0 CY, PORT5.1 CY SETP PORT5.3 PORT5.3 ; CY ← 1 ; CY ^ P30 ; CY ^ P51 ; CY = 1? ; P53 ← 0 ; P53 ← 1 (ii) PORT3.0 SETP PORT5.1 SETP PORT5.3 PORT5.3 ; P30 = 1? ; P51 = 1? ; P53 ← 0 ; P53 ← 1 55 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP (b) Specific address bit register indirect addressing (pmem. @L) This addressing mode is used to indirectly specify and successively manipulate the bits of the peripheral hardware units, such as I/O ports. The data memory addresses to which this addressing mode can be applied are FC0H through FFFH. This addressing mode specifies the higher 10 bits of a data memory address directly by using an operand, and the lower 2 bits by using the L register. Therefore, 16 bits (4 ports) can be successively manipulated depending on the specification of the L register. This addressing mode can also be used independently of the setting of MBE and MBS. Example To output pulses to the respective bits of ports 8 and 9 P80 P81 to P93 LOOP2: MOV LOOP1: SET1 CLR1 INCS NOP SKE BR BR L, #0 PORT8.@L PORT8.@L L L, #08H LOOP1 LOOP2 ; Bits of ports 8 and 9 (L 1-0) ← 1 ; Bits of ports 8 and 9 (L 1-0) ← 0 56 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP (c) Special 1-bit direct addressing (@H+mem. bit) This addressing mode enables bit manipulation in the entire data memory space. The higher 4 bits of the data memory address of the memory bank specified by MBE and MBS are indirectly specified by the H register, and the lower 4 bits and the bit address are directly specified by the operand. This addressing mode can be used to manipulate the respective bits of the entire data memory area in various ways. Example To reset bit 2 (FLAG3) at address 32H if both bit 3 (FLAG1) at address 30H and bit 0 (FLAG2) at address 31H are 0 or 1 FLAG1 FLAG2 FLAG3 FLAG1 FLAG2 FLAG3 EQU EQU EQU SEL MOV CLR1 OR1 XOR1 SET1 SKT CLR1 30H.3 31H.0 32H.2 MB0 H, #FLAG1 SHR 6 CY CY, @H+FLAG1 CY, @H+FLAG2 @H+FLAG3 CY @H+FLAG3 ; CY ← 0 ; CY ← CY v FLAG1 ; CY ← CY v FLAG2 ; FLAG3 ← 1 ; CY = 1? ; FLAG3 ← 0 57 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP (7) Stack addressing This addressing mode is used to save or restore data when interrupt processing or subroutine processing is executed. The address of data memory bank 0 pointed to by the stack pointer (8 bits) is specified in this addressing mode. This addressing is also used to save or restore register contents by using the PUSH or POP instruction, in addition to during interrupt processing or subroutine processing. Examples 1. To save or restore register contents during subroutine processing SUB: PUSH PUSH PUSH POP POP POP RET 2. To transfer contents of register pair HL to register pair DE PUSH POP HL DE ; DE ← HL . . . XA HL BS BS HL XA ; Saves MBS and RBS 3. To branch to address specified by registers [XABC] PUSH PUSH RET BC XA ; To branch address XABC 58 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP 3.2 Bank Configuration of General-Purpose Registers The µ PD753108 is provided with four register banks with each bank consisting of eight general-purpose registers: X, A, B, C, D, E, H, and L. The general-purpose register area consisting of these registers is mapped to the addresses 00H through 1FH of memory bank 0 (refer to Figure 3-5). To specify a general-purpose register bank, a register bank enable flag (RBE) and a register bank select register (RBS) are provided. RBS selects a register bank, and RBE determines whether the register bank selected by RBS is valid or not. The register bank (RB) that is enabled when an instruction is executed is as follows: RB = RBE·RBS Table 3-2. Register Bank Selected by RBE and RBS RBS RBE 3 0 1 0 0 2 0 0 1 × 0 0 1 1 0 × 0 1 0 1 Fixed to bank 0 Bank 0 selection Bank 1 selection Bank 2 selection Bank 3 selection Register Bank Fixed to 0 Remark × = don’t care RBE is automatically saved or restored during subroutine processing, and therefore can be set while subroutine processing is under execution. When interrupt processing is executed, RBE is automatically saved or restored, and RBE can be set during interrupt processing depending on the setting of the interrupt vector table as soon as the interrupt processing is started. Consequently, if different register banks are used for normal processing and interrupt processing as shown in Table 3-3, it is not necessary to save or restore general-purpose registers when an interrupt is processed, and only RBS needs to be saved or restored if two interrupts are nested, so that the interrupt processing speed can be increased. 59 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP Table 3-3. Example of Using Different Register Banks for Normal Routine and Interrupt Routine Normal processing Single interrupt processing Nesting processing of two interrupts Nesting processing of three or more interrupts Uses register banks 2 or 3 with RBE = 1 Uses register bank 0 with RBE = 0 Uses register bank 1 with RBE = 1 (at this time, RBS must be saved or restored) Registers must be saved or restored by PUSH or POP instructions Figure 3-4. Example of Using Register Banks SET1 RBE SEL RB2 ; RBE = 1 ; RBE = 0 in vector table in vector table PUSH BS SEL RB1 RB = 0 RB = 1 RB = 0 ; RBE = 0 in vector table PUSH rp RB = 2 RETI POP BS RETI POP rp RETI If RBS is to be changed in the course of subroutine processing or interrupt processing, it must be saved or restored by using the PUSH or POP instruction. RBE is set by using the SET1 or CLR1 instruction. RBS is set by using the SEL instruction. Example SET1 CLR1 SEL SEL RBE RBE RB0 RB3 ; RBE ← 1 ; RBE ← 0 ; RBS ← 0 ; RBS ← 3 The general-purpose register area provided to the µ PD753108 can be used not only as 4-bit registers, but also as 8-bit register pairs. This feature allows the µ PD753108 to provide transfer, operation, comparison, and increment/decrement instructions comparable to those of 8-bit microcontrollers and allows you to program mainly with general-purpose registers. 60 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP (1) To use as 4-bit registers When the general-purpose register area is used as a 4-bit register area, a total of eight general-purpose registers, X, A, B, C, D, E, H, and L, specified by RBE and RBS can be used as shown in Figure 3-5. Of these registers, A plays a central role in transferring, operating, and comparing 4-bit data as a 4-bit accumulator. The other registers can transfer, compare, and increment or decrement data with the accumulator. (2) To use as 8-bit registers When the general-purpose register area is used as an 8-bit register area, a total of eight 8-bit register pairs can be used as shown in Figure 3-6: register pairs XA, BC, DE, and HL of a register bank specified by RBE and RBS, and register pairs XA’, BC’, DE’, and HL’ of the register bank whose bit 0 is complemented in respect to the register bank (RB). Of these register pairs, XA serves as an 8-bit accumulator, playing the central role in transferring, operating, and comparing 8-bit data. The other register pairs can transfer, compare, and increment or decrement data with the accumulator. The HL register pair is mainly used as a data pointer. The DE and DL register pairs are also used as auxiliary data pointers. Examples 1. INCS ADDS SUBC MOV MOVT SKE HL XA, BC DE’, XA XA, XA’ XA, @PCDE XA, BC ; Skips if HL ← HL + 1, HL = 00H ; Skips if XA ← XA + BC, carry ; DE’ ← DE’ – XA – CY ; XA ← XA’ ; XA ← (PC12-8+DE)ROM, table reference ; Skips if XA = BC 2. To test whether the value of the count register (T0) of timer/event counter 0 is greater than the value of register pair BC’ and, if not, wait until it becomes greater CLR1 NO: MOV SUBS BR BR MBE XA, T0 XA, BC’ YES NO ; Reads count register ; XA ≥ BC’? ; YES ; NO 61 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP Figure 3-5. General-Purpose Register Configuration (for 4-bit operation) X 01H H 03H D 05H B 07H X 09H H 0BH D 0DH B 0FH X 11H H 13H D 15H B 17H X 19H H 1BH D 1DH B 1FH A 00H L 02H E 04H C 06H A 08H L 0AH E 0CH C 0EH A 10H L 12H E 14H C 16H A 18H L 1AH E 1CH C 1EH Register bank 3 (RBE · RBS = 3) Register bank 2 (RBE · RBS = 2) Register bank 1 (RBE · RBS = 1) Register bank 0 (RBE · RBS = 0) 62 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP Figure 3-6. General-Purpose Register Configuration (for 8-bit operation) XA 00H XA' 00H HL 02H DE 04H BC 06H XA' 08H HL' 0AH DE' 0CH BC' 0EH When RBE · RBS = 0 HL' 02H DE' 04H BC' 06H XA 08H HL 0AH DE 0CH BC 0EH When RBE · RBS = 1 XA 10H HL 12H DE 14H BC 16H XA' When RBE · RBS = 2 XA' 10H HL' 12H DE' 14H BC' 16H XA 18H HL 1AH 1AH DE 1CH 1CH BC 1EH 1EH 18H When RBE · RBS = 3 HL' DE' BC' 63 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP 3.3 Memory-Mapped I/O The µPD753108 employs memory-mapped I/O where peripheral hardware such as the input/output ports and timers are mapped in data memory space addresses F80H to FFFH, as shown in Figure 3-2. Thus, special instructions to control the peripheral hardware are not provided and memory manipulation instructions are all used to control the peripheral hardware (Some hardware control mnemonics are provided for easy understanding of programs). To manipulate the peripheral hardware, the addressing modes listed in Table 3-4 can be used. The display data memory mapped in addresses 1E0H to 1F7H is manipulated by specifying memory bank 1. Table 3-4. Addressing Modes Applicable to Operating Peripheral Hardware Applicable Addressing Mode Bit manipulation Specified by a direct addressing mem.bit with MBE = 0 or (MBE = 1, MBS = 15). Specified by direct addressing fmem.bit regardless of MBE and MBS. Specified by indirect addressing pmem.@L regardless of MBE and MBS. 4-bit manipulation Specified by direct addressing mem with MBE = 0 or (MBE = 1, MBS = 15). Specified by register indirect addressing @HL with (MBE = 1, MBS = 15). 8-bit manipulation Specified by direct addressing mem with MBE = 0 or (MBE = 1, MBS = 15). Note that mem must be an even-number address. Specified by register indirect addressing @HL with MBE = 1, MBS = 15. Note that the contents of the L register are an even number. All the hardware for which 8-bit manipulation is possible Applicable Hardware All the hardware for which bit manipulation is possible IST1, IST0, MBE, RBE IEXXX, IRQXXX, PORTn.X BSBn.X PORTn.X All the hardware for which 4-bit manipulation is possible Example CLR1 SET1 EI DI SET1 MBE TM0. 3 IE0 IE1 PORT5. @L ; MBE = 0 ; Starts timer 0 ; Enables INT0 ; Disables INT1 ; Tests and clears INT2 request flag ; Sets port 5 SKTCLR IRQ2 64 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP The I/O map of the µ PD753108 is shown in Figure 3-7. The meanings of the items in Figure 3-7 are as follows. • Hardware name ....... A name indicating the address of on-chip hardware. Can be described in the operand (symbol) column of instruction. • R/W ........................... Indicates whether the given hardware is read/write enabled or not. R/W : read/write enabled R W : read only : write only • Manipulation unit ..... Indicates the number of bits in which the hardware device can be manipulated. Yes : Bit manipulation is possible in the unit (1/4/8 bits) used in the column. ∆ — : A part of bits can be manipulated. Refer to “Remarks” for the bits that can be manipulated. : Bit manipulation is impossible in the unit (1/4/8 bits) used in the column. • Bit manipulation ....... Indicates the usable bit manipulation addressing when bit manipulation is performed addressing on the hardware. 65 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP Figure 3-7. µ PD753108 I/O Map (1/5) Hardware Name (symbol) Address b3 F80H b2 b1 b0 R/W Stack pointer (SP) R/W Manipulation Unit Bit Manipulation 1-bit 4-bit 8-bit Addressing — — Yes — Bit 0 is fixed to 0. Remarks F82H F83H F84H F85H F86H Register bank selection register (RBS) R Bank selection register (BS) Memory bank selection register (MBS) Stack bank selection register (SBS) R/W Basic interval timer mode register (BTM) Basic interval timer (BT) W R — — — ∆ — Yes Yes Yes Yes — Yes — Note 1 — — Yes — mem.bit — Bit manipulation can be performed only on bit 3. F88H Modulo register for setting timer/ event counter high level (TMOD2H) WDTMNote 2 Display mode register (LCDM) R/W — — Yes — F8BH F8CH W ∆ — — — Yes Yes — Yes mem.bit mem.bit Bit manipulation can be performed only on bit 3. Bit manipulation can be performed only on bit 3. R/W ∆ (W) — F8EH F8FH Display control register (LCDC) LCD/port selection register (LPS) R/W R/W — — — — — — Notes 1. The manipulation is possible separately with RBS and MBS in the 4-bit manipulation. The manipulation is possible with BS in the 8-bit manipulation. Write data in the MBS and RBS with the SEL MBn and SEL RBn instructions. 2. WDTM: Watchdog timer enable flag (W); Cannot be cleared, once set, by an instruction. 66 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP Figure 3-7. µ PD753108 I/O Map (2/5) Hardware Name (symbol) Address b3 F90H b2 b1 b0 Timer/event counter 2 mode register (TM2) R/W Manipulation Unit Bit Manipulation 1-bit 4-bit 8-bit Addressing — — Yes — — Yes — Yes Yes — — — Bit 3 can be written only. Bit manipulation can be performed only on bit 3. Remarks Bit manipulation can be performed only on bit 3. R/W ∆ (W) — Yes ∆ — F92H F94H TOE2 REMC NRZB NRZ R/W Timer/event counter 2 control register (TC2) TGCE — — — Timer/event counter 2 count register (T2) R F96H Timer/event counter 2 modulo register R/W (TMOD2) Watch mode register (WM) — — Yes — F98H R/W ∆ (R) — R/W ∆ (W) — W R Yes — — — Yes — Bit manipulation can be performed only on bit 3. FA0H Timer/event counter 0 mode register (TM0) — — — — Yes mem.bit — Bit manipulation can be performed only on bit 3. FA2H FA4H TOE0Note 1 Timer/event counter 0 count register (T0) — Yes mem.bit — FA6H Timer/event counter 0 modulo register R/W (TMOD0) Timer/event counter 1 mode register (TM1) TOE1Note 2 Timer/event counter 1 count register (T1) — — Yes — FA8H R/W ∆ (W) — W R Yes — — — — — Yes mem.bit — Bit manipulation can be performed only on bit 3. FAAH FACH — Yes mem.bit — FAEH Timer/event counter 1 modulo register R/W (TMOD1) — — Yes — Notes 1. TOE0: Timer/event counter output enable flag (channel 0) (W) 2. TOE1: Timer/event counter output enable flag (channel 1) (W) 67 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP Figure 3-7. µ PD753108 I/O Map (3/5) Hardware Name (symbol) Address b3 FB0H b2 b1 b0 R/W Manipulation Unit Bit Manipulation 1-bit 4-bit 8-bit Addressing fmem.bit Remarks 8-bit manipulation is read only. FB2H FB3H FB4H FB5H FB6H FB7H FB8H FBAH FBCH FBDH FBEH FBFH IST1 IST0 MBE RBE R/W Yes (R/W) Yes (R/W) Yes Program status word (PSW) (R) ∆Note 2 — CY Note 1 SK2Note 1 SK1Note 1 SK0Note 1 Interrupt priority selection register (IPS) R/W — Yes — Processor clock control register (PCC) R/W INT0 edge detection mode register (IM0) R/W INT1 edge detection mode register (IM1) R/W INT2 edge detection mode register (IM2) R/W System clock control register (SCC) INTA register (INTA) IE4 IRQ4 INTC register (INTC) INTE register (INTE) IET1 IRQT1 INTF register (INTF) IET2 IRQT2 INTG register (INTG) IE1 IRQ1 INTH register (INTH) IEBT IEW IET0 IECSI IE0 IE2 IRQBT IRQW IRQT0 IRQCSI IRQ0 IRQ2 Note 3 Note 4 — — — — — ∆ Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes — — R/W R/W R/W R/W R/W R/W R/W — — — fmem.bit Bit manipulation can be performed only on bits 0, 3. — — FC0H FC1H FC2H FC3H FCFH Bit sequential buffer 0 (BSB0) Bit sequential buffer 1 (BSB1) Bit sequential buffer 2 (BSB2) Bit sequential buffer 3 (BSB3) R/W R/W R/W R/W Yes Yes Yes Yes — Yes Yes Yes Yes Yes Yes mem.bit pmem.@L Yes Subsystem clock oscillator control register (SOS) R/W — — Remarks 1. IEXXX : Interrupt enable flag 2. IRQXXX: Interrupt request flag Notes 1. Not registered as a reserved word. 2. Write into CY with CY manipulation instruction. 3. Only bit 3 can be manipulated with an EI/DI instruction. 4. Bits 3 and 2 can be manipulated bit-wise when a STOP or HALT instruction is executed. 68 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP Figure 3-7. µ PD753108 I/O Map (4/5) Hardware Name (symbol) Address b3 FD0H FDCH b2 b1 b0 R/W R/W Clock output mode register (CLOM) Pull-up resistor specification register group A (POGA) FDEH Pull-up resistor specification register group B (POGB) R/W — — Yes — R/W Manipulation Unit Bit Manipulation 1-bit 4-bit 8-bit Addressing — — Yes — — Yes — — Remarks FE0H Serial operation mode register (CSIM) R/W CSIE COI WUP CMDD RELD CMDT RELT SBI control register (SBIC) BSYE ACKD ACKE ACKT Serial I/O shift register (SIO) R/W — ∆ (R) (W) — — — Yes — mem.bit Note 1 FE2H Yes — mem.bit R/W depends on the bit number. FE4H R/W — — Yes — FE6H Slave address register (SVA) R/W — — Yes — FE8H FECH FEEH PM33Note 2 PM32 Note 2 PM31 Note 2 PM30 Note 2 R/W Port mode register group A (PMGA) PM63Note 2 PM62 Note 2 PM61 Note 2 PM60 Note 2 — PM2Note 2 — — R/W Port mode register group B (PMGB) — — PM5Note 2 — — — PM9Note 2 PM8Note 2 R/W Port mode register group C (PMGC) — — — — — — Yes — — — Yes — — — Yes — Notes 1. For the 1-bit manipulation, R/W depends on the bit number. 2. Not registered as a reserved word. 69 CHAPTER 3 FEATURES OF ARCHITECTURE AND MEMORY MAP Figure 3-7. µPD753108 I/O Map (5/5) Hardware Name (symbol) Address b3 FF0H FF1H FF2H FF3H FF5H FF6H FF8H FF9H Port 0 Port 1 Port 2 Port 3 Port 5 KR3 Port 6 KR2 KR1 R/W b2 b1 b0 (PORT0) (PORT1) R R Manipulation Unit Bit Manipulation 1-bit 4-bit 8-bit Addressing Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes — — Yes fmem.bit pmem.@L — — — Remarks (PORT2) R/W (PORT3) R/W (PORT5) R/W KR0 (PORT6) R/W Port 8 Port 9 (PORT8) R/W (PORT9) R/W 70 CHAPTER 4 INTERNAL CPU FUNCTIONS 4.1 4.1.1 Switching Function between Mk I Mode and Mk II Mode Difference between Mk I and Mk II modes The CPU of the µPD753108 has the following two modes: Mk I and Mk II, either of which can be selected. The mode can be switched by the bit 3 of the stack bank selection register (SBS). • Mk I mode : Upward compatible with the µPD75308B. Can be used in the 75XL CPU with a ROM capacity of up to 16 Kbytes. • Mk II mode : Incompatible with the µPD75308B. Can be used in all the 75XL CPU’s including those devices whose ROM capacity is more than 16 Kbytes. Table 4-1. Differences between Mk I Mode and Mk II Mode Mk I Mode Number of stack bytes for subroutine instructions BRA !addr1 instruction CALLA !addr1 instruction CALL !addr instruction CALLF !faddr instruction 3 machine cycles 2 machine cycles 4 machine cycles 3 machine cycles 2 bytes Not available 3 bytes Available Mk II Mode Caution Mk II mode supports the program area that exceeds 16 Kbytes in 75X and 75XL Series. A software compatibility with devices whose ROM capacity is more than 16 Kbytes can be improved with this mode. In Mk II mode, the stack byte number (use area) during subroutine call instruction execution increases one byte per one stack compared to that of Mk I mode. Moreover, the machine cycle is lengthened for one cycle at the execution of CALL !addr or CALLF !faddr instruction. Therefore, Mk I mode is recommended for applications with a focus on the RAM efficiency or processing performance rather than the software compatibility. 71 CHAPTER 4 INTERNAL CPU FUNCTIONS 4.1.2 Setting method of stack bank selection register (SBS) Switching between the Mk I mode and Mk II mode can be done by the SBS. Figure 4-1 shows the format. The SBS is set by a 4-bit memory manipulation instruction. When using the Mk I mode, the SBS must be initialized to 100XBNote at the beginning of a program. When using the Mk II mode, it must be initialized to 000XBNote . Note Set a desired value to X. Figure 4-1. Stack Bank Selection Register Format Address F84H 3 2 1 0 SBS0 Symbol SBS SBS3 SBS2 SBS1 Stack area specification 0 0 0 1 Memory bank 0 Memory bank 1 Other than above setting prohibited 0 0 must be set in the bit 2 position. Mode switching specification 0 1 Mk II mode Mk I mode Caution Because SBS. 3 is set to “1” after a RESET signal is generated, the CPU operates in the Mk I mode. When executing an instruction in the Mk II mode, set SBS. 3 to “0” to select the Mk II mode. 72 CHAPTER 4 INTERNAL CPU FUNCTIONS 4.2 Program Counter (PC) ····· 12-bit (µPD753104) 13-bit (µPD753106, 753108) 14-bit (µPD75P3116) This is a binary counter that holds an address of the program memory. Figure 4-2. Program Counter Configuration (a) µ PD753104 PC11 PC10 PC9 PC8 PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 (b) µ PD753106, 753108 PC12 PC11 PC10 PC9 PC8 PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 (c) µ PD75P3116 PC13 PC12 PC11 PC10 PC9 PC8 PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0 The value of the program counter (PC) is usually automatically incremented by the number of bytes of an instruction each time an instruction has been executed. When a branch instruction (BR, BRA, or BRCB) is executed, immediate data indicating the branch destination address or the contents of a register pair are loaded to all or some bits of the PC. When a subroutine call instruction (CALL, CALLA, or CALLF) is executed or when a vectored interrupt occurs, the contents of the PC (a return address already incremented to fetch the next instruction) are saved to the stack memory (data memory specified by the stack pointer) and then the jump destination address is loaded to the PC. When the return instruction (RET, RETS, or RETI) is executed, the contents of the stack memory are set to the PC. When the RESET signal is asserted, the program counter (PC) is loaded with the contents of addresses 0000H and 0001H in the program memory as shown below. The program can start from any address according to the contents of the 0000H and 0001H addresses. µ PD753104 µ PD753106, 753108 µ PD75P3116 : PC 11-8 ← (0000H) 3-0, : PC 12-8 ← (0000H) 4-0, : PC 13-8 ← (0000H) 5-0, PC 7-0 ← (0001H) 7-0 PC 7-0 ← (0001H) 7-0 PC 7-0 ← (0001H) 7-0 73 CHAPTER 4 INTERNAL CPU FUNCTIONS 4.3 Program Memory (ROM) ·····4096 × 8 bits (µPD753104) 6144 × 8 bits (µPD753106) 8192 × 8 bits (µPD753108) 16384 × 8 bits (µPD75P3116) The program memory is provided to store the programs, interrupt vector table, reference table of the GETI instruction, and table data. It is addressed by the program counter. Table data can be referenced by the table reference instruction (MOVT). The range of addresses to which branches can be taken by a branch instruction and subroutine call instruction is shown in Figure 4-3. A branch can take place to address (contents of PC –15 to –1, +2 to +16) by a relative branch instruction (BR $addr instruction). The address range of the program memory of each model is as follows: • 000H to FFFH : µ PD753104 • 0000H to 17FFH : µ PD753106 • 0000H to 1FFFH: µ PD753108 • 0000H to 3FFFH: µ PD75P3116 Special functions are assigned to the following addresses. All the addresses other than 0000H and 0001H can be usually used as program memory addresses. • Addresses 0000H and 0001H Vector table wherein the program start address and the values set for the RBE and MBE at the time a RESET signal is generated are written. Reset and start are possible at any address. • Addresses 0002H to 000DH Vector table wherein the program start address and values set for the RBE and MBE by the vectored interrupts are written. Interrupt execution can be started at any address. • Addresses 0020H to 007FH Table area referenced by the GETI instruction.Note Note The GETI instruction realizes a 1-byte instruction on behalf of any 2-byte instruction, 3-byte instruction, or two 1-byte instructions. It is used to decrease the program steps (See section 11.1.1 GETI instruction ). 74 CHAPTER 4 INTERNAL CPU FUNCTIONS Figure 4-3. Program Memory Map (1/4) (a) µ PD753104 Address 000H 7 6 5 0 4 0 Internal reset start address Internal reset start address 002H MBE RBE 0 0 INTBT/INT4 INTBT/INT4 004H MBE RBE 0 0 INT0 INT0 006H MBE RBE 0 0 INT1 INT1 008H MBE RBE 0 0 INTCSI INTCSI 00AH MBE RBE 0 0 INTT0 INTT0 00CH MBE RBE 0 0 INTT1/INTT2 INTT1/INTT2 start address start address start address start address start address start address start address start address start address start address start address start address 0 (high-order 4 bits) (low-order 8 bits) (high-order 4 bits) (low-order 8 bits) (high-order 4 bits) (low-order 8 bits) (high-order 4 bits) (low-order 8 bits) (high-order 4 bits) (low-order 8 bits) (high-order 4 bits) (low-order 8 bits) (high-order 4 bits) (low-order 8 bits) CALL !addr instruction subroutine entry address CALLF !faddr instruction entry address Branch address of BR BCXA, BR BCDE, BR !addr, BRA !addr1Note or CALLA !addr1Note instruction MBE RBE BR $addr instruction relative branch address –15 to –1, +2 to +16 BRCB !caddr instruction branch address 020H GETI instruction reference table 07FH 080H 7FFH 800H Branch destination address and subroutine entry address when GETI instruction is executed FFFH Note Can be used only in the Mk II mode. Remark In addition to the above, a branch can be taken to the address indicated by changing only the loworder eight bits of PC by executing the BR PCDE or BR PCXA instruction. 75 CHAPTER 4 INTERNAL CPU FUNCTIONS Figure 4-3. Program Memory Map (2/4) (b) µ PD753106 Address 0000H 7 6 5 0 Internal reset start address Internal reset start address 0002H MBE RBE 0 INTBT/INT4 INTBT/INT4 0004H MBE RBE 0 INT0 INT0 0006H MBE RBE 0 INT1 INT1 0008H MBE RBE 0 INTCSI INTCSI 000AH MBE RBE 0 INTT0 INTT0 000CH MBE RBE 0 INTT1/INTT2 INTT1/INTT2 start address start address start address start address start address start address start address start address start address start address start address start address 0 (high-order 5 bits) (low-order 8 bits) (high-order 5 bits) (low-order 8 bits) (high-order 5 bits) (low-order 8 bits) (high-order 5 bits) (low-order 8 bits) (high-order 5 bits) (low-order 8 bits) (high-order 5 bits) (low-order 8 bits) (high-order 5 bits) (low-order 8 bits) CALLF !faddr instruction entry address Branch address of BR BCXA, BR BCDE, BR !addr, BRA !addr1Note or CALLA !addr1Note instruction CALL !addr instruction subroutine entry address BR $addr instruction relative branch address –15 to –1, +2 to +16 MBE RBE 0020H GETI instruction reference table 007FH 0080H BRCB !caddr instruction branch address Branch destination address and subroutine entry address when GETI instruction is executed 07FFH 0800H 0FFFH 1000H BRCB !caddr instruction branch address 17FFH Note Can be used only in the Mk II mode. Remark In addition to the above, a branch can be taken to the address indicated by changing only the loworder eight bits of PC by executing the BR PCDE or BR PCXA instruction. 76 CHAPTER 4 INTERNAL CPU FUNCTIONS Figure 4-3. Program Memory Map (3/4) (c) µ PD753108 Address 0000H 7 6 5 0 Internal reset start address Internal reset start address 0002H MBE RBE 0 INTBT/INT4 INTBT/INT4 0004H MBE RBE 0 INT0 INT0 0006H MBE RBE 0 INT1 INT1 0008H MBE RBE 0 INTCSI INTCSI 000AH MBE RBE 0 INTT0 INTT0 000CH MBE RBE 0 INTT1/INTT2 INTT1/INTT2 start address start address start address start address start address start address start address start address start address start address start address start address 0 (high-order 5 bits) (low-order 8 bits) (high-order 5 bits) (low-order 8 bits) (high-order 5 bits) (low-order 8 bits) (high-order 5 bits) (low-order 8 bits) (high-order 5 bits) (low-order 8 bits) (high-order 5 bits) (low-order 8 bits) (high-order 5 bits) (low-order 8 bits) BRCB !caddr instruction branch address CALLF !faddr instruction entry address Branch address of BR BCXA, BR BCDE, BR !addr, BRA !addr1Note or CALLA !addr1Note instruction CALL !addr instruction subroutine entry address BR $addr instruction relative branch address –15 to –1, +2 to +16 MBE RBE 0020H GETI instruction reference table 007FH 0080H Branch destination address and subroutine entry address when GETI instruction is executed 07FFH 0800H 0FFFH 1000H BRCB !caddr instruction branch address 1FFFH Note Can be used only in the Mk II mode. Remark In addition to the above, a branch can be taken to the address indicated by changing only the loworder eight bits of PC by executing the BR PCDE or BR PCXA instruction. 77 CHAPTER 4 INTERNAL CPU FUNCTIONS Figure 4-3. Program Memory Map (4/4) (d) µ PD75P3116 Address 7 6 RBE 5 Internal reset start address (high-order 6 bits) Internal reset start address (low-order 8 bits) 0002H MBE RBE INTBWT/INT4 start address (high-order 6 bits) INTBWT/INT4 start address (low-order 8 bits) 0004H MBE RBE INT0 start address (high-order 6 bits) INT0 start address (low-order 8 bits) 0006H MBE RBE INT1 start address (high-order 6 bits) INT1 start address (low-order 8 bits) 0008H MBE RBE INTCSI start address (high-order 6 bits) INTCSI start address (low-order 8 bits) 000AH MBE RBE INTT0 start address (high-order 6 bits) INTT0 start address (low-order 8 bits) 000CH MBE RBE INTT1/INTT2 start address (high-order 6 bits) INTT1/INTT2 start address (low-order 8 bits) Branch address of BR !addr, CALL !addr, BRA !addr1Note, Note , CALLA !add1 BR BCDE or BR BCXA instruction BRCB !caddr instruction branch address CALLF !faddr instruction entry address 0 0000H MBE 0020H GETI instruction reference table 007FH 0080H 07FFH 0800H 0FFFH 1000H Branch/call address by GETI BR $addr instruction relative branch address (–15 to –1, +2 to +16) 1FFFH 2000H BRCB !caddr instruction branch address BRCB !caddr instruction branch address BRCB !caddr instruction branch address 2FFFH 3000H 3FFFH Note Can be used only in the Mk II mode. Remark In addition to the above, a branch can be taken to the address indicated by changing only the loworder eight bits of PC by executing the BR PCDE or BR PCXA instruction. 78 CHAPTER 4 INTERNAL CPU FUNCTIONS 4.4 Data Memory (RAM) ··· 512 words × 4 bits The data memory consists of data areas and a peripheral hardware area as shown in Figure 4-4. The data memory consists of the following banks, with each bank made up of 256 words × 4 bits: • Memory banks 0 and 1 (data areas) • Memory bank 15 (peripheral hardware area) 4.4.1 Configuration of data memory (1) Data area A data area consists of static RAM, and is used to store data and as a stack memory when a subroutine or interrupt is executed. The contents of this area can be backed up for a long time by batteries even when the CPU is stopped in the standby mode. The data area is manipulated by using memory manipulation instructions. Static RAM is mapped to memory banks 0 and 1 in units of 256 × 4 bits each. Although bank 0 is mapped as a data area, it can also be used as a general-purpose register area (000H through 01FH) and as a stack areaNote 1 (000H through 1FFH). Bank 1 can be used as a display data memory (1E0H through 1F7H). One address of the static RAM consists of 4 bits. However, it can be manipulated in 8-bit units by using an 8-bit memory manipulation instruction, or in 1-bit units by using a bit manipulation instruction Note 2. To use an 8-bit manipulation instruction, specify an even address. Notes 1. One stack area can be selected from memory bank 0 or 1. 2. The display data memory cannot be manipulated in 8-bit units. • General-purpose register area This area can be manipulated by using a general-purpose register manipulation instruction or memory manipulation instruction. Up to eight 4-bit registers can be used. The registers not used by the program can be used as part of the data area or stack area. • Stack area The stack area is set by an instruction and is used as a saving area when a subroutine or interrupt processing is executed. • Display data memory The display data of an LCD are written to this area. The data written to this display data memory are automatically read and displayed by hardware when the LCD is driven. The addresses of this area not used for display can be used as data area addresses. (2) Peripheral hardware area The peripheral hardware area is mapped to addresses F80H through FFFH of memory bank 15. This area is manipulated by using a memory manipulation instruction, in the same manner as the static area. Note, however, that the bit units in which the peripheral hardware units can be manipulated differ depending on the address. The addresses to which no peripheral hardware unit is allocated cannot be accessed because these addresses are not provided to the data memory. 79 CHAPTER 4 INTERNAL CPU FUNCTIONS 4.4.2 Specifying bank of data memory A memory bank is specified by setting a 4-bit memory bank selection register (MBS) to 0, 1, or 15 when bank specification is enabled by setting a memory bank enable flag (MBE) to 1. When bank specification is disabled (MBE = 0), bank 0 or 15 is automatically specified depending on the addressing mode selected at that time. The addresses in the bank are specified by 8-bit immediate data or a register pair. For the details of memory bank selection and addressing, refer to section 3.1 Bank Configuration of Data Memory and Addressing Mode. For how to use a specific area of the data memory, refer to the following chapter or sections: • General-purpose register area ...... See section 4 .5 General-Purpose Registers . • Stack area ...................................... See section 4 .7 Stack Pointer (SP) and Stack Bank Selection Register (SBS) . • Display data memory ................... See section 5 .7.6 Display data memory . • Peripheral hardware area ........... See CHAPTER 5 PERIPHERAL HARDWARE FUNCTION. 80 CHAPTER 4 INTERNAL CPU FUNCTIONS Figure 4-4. Data Memory Map Data memory 000H General-purpose register area 01FH 0 256 × 4 (224 × 4) Stack areaNote Data area static RAM (512 × 4) 0FFH 100H 256 × 4 (224 × 4) 1 1DF 1E0 Display data memory area 1F7 1F8 1FF H H H H H (32 × 4) Memory bank (24 × 4) (8 × 4) Not incorporated F80H Peripheral hardware area 128 × 4 15 FFFH Note Either memory bank 0 or 1 can be assigned to the stack area. 81 CHAPTER 4 INTERNAL CPU FUNCTIONS The contents of the data memory are undefined at reset. Therefore, they must be initialized at the beginning of program execution (RAM clear). Otherwise, unexpected bugs may occur. Example To clear RAM at addresses 000H through 1FFH SET1 SEL MOV MOV RAMC0: MOV INCS BR INCS BR SEL RAMC1: MOV INCS BR INCS BR MBE MB0 XA, #00H HL, #04H @HL, A L RAMC0 H RAMC0 MB1 @HL, A L RAMC1 H RAMC1 ; H ← H+1 ; Clears 100H through 1FFH ; L ← L+1 ; H ← H+1 ; Clears 04H through FFHNote ; L ← L+1 Note Data memory addresses 000H through 003H are not cleared because they are used as general-purpose register pairs XA and HL. 82 CHAPTER 4 INTERNAL CPU FUNCTIONS Figure 4-5. Configuration of Display Data Memory Address 1E0H 1E1H 1E2H 1E3H Display data memory 1F0H 1F1H 1F2H 1F3H 1F4H 1F5H 1F6H 1F7H S16/P93 S17/P92 S18/P91 S19/P90 S20/P83 S21/P82 S22/P81 S23/P80 b3 b2 b1 b0 S0 S1 S2 S3 Segment output COM3 COM2 COM1 COM0 Common signal The display data memory is manipulated in 1- or 4-bit units. Caution Example The display data memory cannot be manipulated in 8-bit units. To clear display data memory at addresses 1E0H through 1F7H SET1 SEL MOV MOV LOOP: MOV INCS SKE SKE BR MBE MB1 HL, #0E0H A, #00H @HL, A HL H, #0EH L, #8H LOOP ; Clears display data memory in 4-bit units at once 83 CHAPTER 4 INTERNAL CPU FUNCTIONS 4.5 General-Purpose Registers ··· 8 × 4 bits × 4 banks The general-purpose registers are mapped in specific addresses of the data memory. There are four registers banks each consisting of eight 4-bit registers (B, C, D, E, H, L, X, and A). The register bank (RB) which becomes valid during instruction execution is determined by the following expression: RB = RBE • RBS (RBS = 0 to 3) Each general-purpose register is manipulated in 4-bit units. In addition, register pairs BC, DE, HL, and XA can also be used for 8-bit manipulation. The DL register can also be paired as well as DE and HL; these three register pairs can be used as data pointers. When two general-purpose registers are manipulated in 8-bit units, register pairs BC’, DE’, HL’, and XA’ of the register bank (0 ↔ 1, 2 ↔ 3) specified by the complement of bit 0 of the register bank (RB) can be used, in addition to BC, DE, HL, and XA (refer to section 3.2 Bank Configuration of General-Purpose Registers). The general-purpose register area can be addressed as normal RAM for an access regardless of whether or not the area is used as registers. Figure 4-6. General-Purpose Register Configuration Figure 4-7. Register Pair Configuration Data memory Address 000H 001H 002H 003H 004H 005H 006H 007H 008H Same configuration as bank 0 00FH 010H Same configuration as bank 0 017H 018H Same configuration as bank 0 01FH Register bank 3 Register bank 2 Register bank 1 3 A register X register L register H register Register bank 0 E register D register C register B register 0 3 B 3 D 3 H 3 X 0 3 C 0 0 3 E 0 0 3 L 0 0 3 A 0          1 bank         84 CHAPTER 4 INTERNAL CPU FUNCTIONS 4.6 Accumulators The µ PD753108 uses the A register and XA register pair as accumulators. The A register is used as the main register during execution of 4-bit data processing instructions; the XA register pair is used as the main register pair during execution of 8-bit data processing instructions. The carry flag (CY) is used for a bit accumulator during execution of bit manipulation instructions. Figure 4-8. Accumulators CY Bit accumulator A 4-bit accumulator X A 8-bit accumulator 4.7 Stack Pointer (SP) and Stack Bank Selection Register (SBS) The µ PD753108 uses static RAM for stack memory (LIFO). The stack pointer (SP) is an 8-bit register which holds top address information of the stack area. The stack area is addresses 000H to 1FFH of memory bank 0 or 1. Specify one memory bank using 2-bit SBS (See Table 4-2). Table 4-2. Stack Area Selected by SBS SBS SBS1 0 0 SBS0 0 1 Memory bank 0 Memory bank 1 Setting prohibited Stack Area Other than above 85 CHAPTER 4 INTERNAL CPU FUNCTIONS The SP decrements before a write (save) operation in the stack memory and increments after a read (restore) operation from it. Figures 4-10 to 4-13 show the data saved and restored by the stack operations. The initial value of the SP is set by an 8-bit memory manipulation instruction and the initial value of the SBS is set by a 4-bit memory manipulation instruction to determine a stack area. Its contents can also be read. When 00H is set in the SP as the initial value, data is stacked first in the highest-order address (nFFH) in the memory bank (n) specified by the SBS. The stack area is limited to the memory bank specified by the SBS, and data is returned to nFFH in the same bank when further stacking operation is performed in addresses starting with n00H. Data cannot be stacked over the boundary of memory bank without rewriting the SBS. Because generation of the RESET signal causes SP to become undefined and SBS to be set to 1000B, be sure to load SP and SBS with user-desired values on the first stage of the program. Figure 4-9. Stack Pointer and Stack Bank Selection Register Configuration Address F80H F84H 000H SBS 0FFH 100H Memory bank 1 1FFH Memory bank 0 SP7 SP6 SP5 SP4 SP3 SBS3 Note Symbol SP2 0 SP1 SBS1 0 SBS0 SP SBS SP SP Note Switching between the Mk I mode and Mk II mode can be done by a SBS3. The stack bank select function can be used in both the Mk I mode and Mk II mode (See 4.1 Switching Function between Mk I Mode and Mk II Mode ). Example SP Initialization Memory bank 1 is assigned to the stack area and data is stacked in addresses starting with 1FFH. SEL MOV MOV MOV MOV MB15 A, #1 SBS, A XA, #00H SP, XA ; SP ← 00H ; Assign memory bank 1 as the stack area. ; or CLR1 MBE 86 CHAPTER 4 INTERNAL CPU FUNCTIONS Figure 4-10. Data Saved in Stack Memory (Mk I mode) PUSH instruction Stack SP – 4 CALL, CALLF instruction Stack PC11 to PC8 Note 2 Interrupt Stack SP – 6 PC11 to PC8 Note 2 Note 1 PC12 SP – 3 MBE RBE 0 SP – 5 MBE RBE 0Note 1 PC12 SP – 4 SP – 3 PC3 to PC0 PC7 to PC4 SP – 2 SP – 1 SP Register pair low order Register pair high order SP – 2 SP – 1 SP PC3 to PC0 PC7 to PC4 SP – 2 IST1 IST0 MBE RBE PSW SP – 1 SP CY SK2 SK1 SK0 Figure 4-11. Data Restored from Stack Memory (Mk I mode) POP instruction Stack SP SP+1 SP+2 Register pair low order Register pair high order SP SP+1 SP+2 SP+ 3 SP+4 RET, RETS instruction Stack PC11 to PC8 MBE RBE 0Note 1 PC12 PC3 to PC0 PC7 to PC4 Note 2 RETI instruction Stack SP SP+1 SP+2 SP+3 SP+4 SP+5 SP+6 PC11 to PC8 MBE RBE 0Note 1 PC12 PC3 to PC0 PC7 to PC4 IST1 IST0 MBE RBE PSW CY SK2 SK1 SK0 Note 2 Notes 1. For the µ PD75P3116, PC13 is saved to this position. 2. For the µ PD753104, PC12 is set to 0. 87 CHAPTER 4 INTERNAL CPU FUNCTIONS Figure 4-12. Data Saved in Stack Memory (Mk II mode) PUSH instruction Stack CALL, CALLA, CALLF instruction Stack SP – 6 SP – 5 0 PC11 to PC8 0 0Note 1 PC12 Note 2 Interrupt Stack SP – 6 SP – 5 SP – 4 SP – 3 0 PC11 to PC8 0 0Note 1 PC12 Note 2 SP – 2 SP – 1 SP Register pair low order Register pair high order SP – 4 SP – 3 SP – 2 SP – 1 SP PC3 to PC0 PC7 to PC4 PC3 to PC0 PC7 to PC4 * * * * MBE RBE Note 3 SP – 2 IST1 IST0 MBE RBE PSW SP – 1 SP CY SK2 SK1 SK0 * * Figure 4-13. Data Restored from Stack Memory (Mk II mode) POP instruction Stack SP SP+ 1 SP+ 2 Register pair low order Register pair high order SP SP+ 1 SP+ 2 SP+ 3 SP+ 4 SP+ 5 SP+ 6 0 RET, RETS instruction Stack PC11 to PC8 0 0Note 1 PC12 Note 2 RETI instruction Stack SP SP+ 1 SP+ 2 SP+ 3 0 PC11 to PC8 0 0Note 1 PC12 Note 2 PC3 to PC0 PC7 to PC4 PC3 to PC0 PC7 to PC4 * * * * MBE RBE Note 3 * * SP+ 4 IST1 IST0 MBE RBE PSW SP+ 5 CY SK2 SK1 SK0 SP+ 6 Notes 1. For the µ PD75P3116, PC13 is saved to this position. 2. For the µ PD753104, PC12 is set to 0. 3. PSW other than MBE and RBE is not saved/restored. Remark A star mark (*) in the above illustrations means undefined. 88 CHAPTER 4 INTERNAL CPU FUNCTIONS 4.8 Program Status Word (PSW) ··· 8 bits The program status word (PSW) consists of flags closely related to processor operation. PSW is mapped in memory space addresses FB0H and FB1H, and four bits of address FB0H can be manipulated by executing a memory manipulation instruction. Figure 4-14. Program Status Word Configuration Address FB1H CY SK2 SK1 SK0 IST1 FB0H IST0 MBE RBE Symbol FB0H PSW Cannot be manipulated Can be manipulated by executing a dedicated instruction Can be manipulated Table 4-3. PSW Flags Saved and Restored during Stack Operation Flags saved and restored Save When CALL, CALLA or CALLF instruction is executed When hardware interrupt is executed Restore When RET or RETS instruction is executed When RETI instruction is executed MBE and RBE are saved All PSW bits are saved MBE and RBE are restored All PSW bits are restored (1) Carry flag (CY) The carry flag (CY) is a 1-bit flag which stores overflow or underflow occurrence information when an operation instruction with carry (ADDC or SUBC) is executed. The carry flag also serves as a bit accumulator. Boolean algebra operation is performed between the bit accumulator and the data memory specified by bit address, and the result can be stored in the accumulator. The carry flag is manipulated by executing a dedicated instruction independently of other PSW bits. When a RESET is input, the carry flag becomes undefined. 89 CHAPTER 4 INTERNAL CPU FUNCTIONS Table 4-4. Carry Flag Manipulation Instructions Instruction (Mnemonics) Carry flag manipulation dedicated instruction SET1 CLR1 NOT1 SKT MOV1 MOV1 Bit Boolean instruction AND1 OR1 XOR1 CY CY CY CY mem*.bit, CY CY, mem*.bit CY, mem*.bit CY, mem*.bit CY, mem*.bit Carry Flag Manipulation and Processing Set CY to 1 Reset CY to 0 Reverses the CY status Skip if CY contains 1 Transfer CY contents to the specified bit Transfer the specified bit contents to CY AND, OR, and XOR in the specified bit contents and CY contents and set the result in CY Save CY and other PSW bits in stack memory in parallel Restore CY and other PSW bits in parallel from stack memory Bit transfer instruction Interrupt processing When interrupt is executed RETI Remark mem*.bit indicates following three bit manipulation addressing • fmem.bit • pmem.@L • @H+mem.bit Example AND address 3FH bit 3 and P33 and output the result to P50. MOV MOV1 AND1 MOV1 H, #3H CY, @H+0FH.3 CY, PORT3.3 PORT5.0, CY ; Set high-order 4-bit address in H register ; CY ← 3FH BIT 3 ; CY ← CY ; P50 ← CY ^ P33 (2) Skip flag (SK2, SK1, SK0) The skip flag stores the skip state. It is automatically set or reset when the CPU executes an instruction. The user cannot directly manipulate the flag as an operand. 90 CHAPTER 4 INTERNAL CPU FUNCTIONS (3) Interrupt status flag (IST1, IST0) The interrupt status flag is a 2-bit flag which stores the status of the current processing being performed (For details, see Table 6-3 IST1 and IST0 and Interrupt Processing Status). Table 4-5. Interrupt Status Flag Indication IST1 0 0 1 1 IST0 0 1 0 1 Status of Processing Being Performed Status 0 Status 1 Status 2 — Processing Indication and Interrupt Control During normal program processing. Acknowledgment of all interrupts is enabled. During low-priority or high-priority interrupt processing. High-priority interrupt acknowledgment is enabled. During high-priority interrupt processing. Acknowledgment of all interrupt is disabled. Setting prohibited The interrupt priority control circuit (see Figure 6-1 Interrupt Control Circuit Block Diagram) judges the interrupt status flag contents to control multiple interrupt. If an interrupt is acknowledged, the IST1 and IST0 contents are saved in the stack memory as a part of PSW, then automatically changed to the upper status. When the RETI instruction is executed, the value before the interrupt service routine is entered is restored. The interrupt status flag can be manipulated by executing a memory manipulating instruction. The status of processing being performed can also be changed under the program control. Caution To manipulate the flag, be sure to execute a DI instruction to disable interrupts before manipulation and execute an EI instruction to enable interrupts after manipulation. 91 CHAPTER 4 INTERNAL CPU FUNCTIONS (4) Memory bank enable flag (MBE) The memory bank enable flag (MBE) is a 1-bit flag to specify the address information generation mode of the high-order four bits of a 12-bit data memory address. MBE can be set or reset at any time, regardless of the setting of the memory bank. When MBE is set to 1, the data memory address space is expanded and all the data memory space can be addressed. When MBE is reset to 0, the data memory address space is fixed regardless of the MBS contents (See Figure 3-2 Data Memory Configuration and Addressing Range for Each Addressing Mode ). When a RESET signal is input, the contents of bit 7 of program memory address 0 is set in MBE for automatic initialization. When vectored interrupt processing is performed, the bit 7 contents of the corresponding vector address table are set and the MBE state during the interrupt service is automatically set. Normally, in interrupt processing, MBE is set to 0 for use of static RAM of memory bank 0. (5) Register bank enable flag (RBE) The register bank enable flag (RBE) is a 1-bit flag to control whether or not the register bank configuration of the general-purpose registers is expanded. RBE can be set or reset at any time, regardless of the setting of the memory bank. When RBE is set to 1, general-purpose registers of one bank can be selected among register banks 0 to 3 according to the register bank selection register (RBS) contents. When RBE is reset to 0, register bank 0 is always selected for general-purpose registers regardless of the register bank selection register (RBS) contents. When a RESET signal is input, the bit 6 contents of program memory address 0 are set in RBE for automatic initialization. When a vectored interrupt occurs, the bit 6 contents of the corresponding vector address table are set and the RBE state during the interrupt service is automatically set. Normally, in interrupt processing, RBE is set to 0 for use of register bank 0 for 4-bit operation or register bank 0 and 1 for 8-bit operation. 92 CHAPTER 4 INTERNAL CPU FUNCTIONS 4.9 Bank Selection Register (BS) The bank selection register (BS) consists of the register bank selection register (RBS) and memory bank selection register (MBS) to specify the register bank and memory bank to be used. RBS and MBS are set by executing SEL RBn and SEL MBn instructions, respectively. BS can be saved in and restored from the stack memory in 8-bit units by executing the PUSH BS and POP BS instructions. Figure 4-15. Bank Selection Register Configuration Address F83H F82H Symbol F82H MBS3 MBS2 MBS1 MBS0 0 0 RBS1 RBS0 BS (1) Memory bank selection register (MBS) The memory bank selection register (MBS) is a 4-bit register which stores high-order 4-bit address information of a 12-bit data memory address. The memory bank to be accessed is specified by the register contents (For the µ PD753108, only banks 0, 1, and 15 can be specified). MBS is set by executing the SEL MBn instruction (n = 0, 1, or 15). The address range for MBE and MBS setting is as shown in Figure 3-2. When a RESET signal is input, MBS is initialized to 0. (2) Register bank selection register (RBS) The register bank selection register (RBS) is a register to specify the register bank used as general- purpose registers. One of banks 0 to 3 can be selected. RBS is set by executing the SEL RBn instruction (n = 0 through 3). When a RESET signal is input, RBS is initialized to 0. Table 4-6. RBE, RBS, and Selected Register Bank RBS RBE 3 0 1 0 0 2 0 0 1 × 0 0 1 1 0 × 0 1 0 1 Fixed to bank 0 Bank 0 selection Bank 1 selection Bank 2 selection Bank 3 selection Register Bank Fixed to 0 × : Don't care 93 [MEMO] 94 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.1 Digital I/O Port Memory mapped I/O is employed for the µPD753108. All the I/O ports are mapped in the data memory space. Figure 5-1. Digital Ports Data Memory Addresses Address FF0H FF1H FF2H FF3H FF5H FF6H FF8H FF9H 3 P03 P13 P23 P33 P53 P63 P83 P93 2 P02 P12 P22 P32 P52 P62 P82 P92 1 P01 P11 P21 P31 P51 P61 P81 P91 0 P00 P10 P20 P30 P50 P60 P80 P90 PORT0 PORT1 PORT2 PORT3 PORT5 PORT6 PORT8 PORT9 Table 5-2 lists the input/output ports manipulation instructions for port 8 and port 9 in addition to 4-bit input/output, 8-bit input/output and bit manipulation can be performed. These enable many types of control. Examples 1. The status shown on P13 is tested and the values depending on the results of test are output to ports 8 and 9. SKT MOV MOV SEL OUT 2. SET1 PORT1.3 XA, #18H XA, #14H MB15 PORT8, XA PORT8. @L ; Skip if bit 3 of port 1 is 1. ; XA ← 18H ; XA ← 14H ; or CLR1 MBE ; ports 9, 8 ← XA ; The bit (in ports 8 and 9) specified by the L register is set to 1. String effect 95 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.1.1 Types, features, configuration of digital I/O ports Table 5-1 lists the types of digital I/O ports. The configurations of the ports are shown in Figures 5-2 to 5-6. Table 5-1. Types and Features of Digital Ports Port (Pin Name) PORT0 (P00 to P03) PORT1 (P10 to P13) PORT2 (P20 to P23) PORT3 (P30 to P33) PORT5 (P50 to P53) Function 4-bit input Operation and Features Remarks The alternate function pins function as outputs depending on Also used for the INT4, SCK, the operation mode when the serial interface function is used. SO/SB0, and SI/SB1 pins. Dedicated 4-bit input port. Also used for the INT0 to INT2 and TI0 to TI2 pins. Also used for the PTO0 to PTO2, PCL, and BUZ pins. Also used for the LCDCL, SYNC, and MD0 to MD3Note 1 pins. Also used for the D4 to D7Note 1 pins. 4-bit I/O Can be set to input mode or output mode in 4-bit units. Can be set to input mode or output mode in 1-bit units. 4-bit I/O (N-channel open-drain, 13 V DC rating) 4-bit I/O Can be set to input mode or output mode in 4-bit units. Pull-up resistor can be connected in 1-bit units by mask optionNote 2. PORT6 (P60 to P63) PORT8 (P80 to P83) PORT9 (P90 to P93) Can be set to input mode or output mode in 1-bit units. Can be set to input mode or output mode in 4-bit units. By combining, data can be input or output in 8-bit units. Also used for the KR0 to KR3 and D0 to D3 Note 1 pins. Also used for the S20 to S23 pins. Also used for the S16 to S19 pins. Notes 1. Alternate function pins only in the µ PD75P3116. 2. Pull-up resistor cannot be connected by mask option in the µ PD75P3116. P10 is also used for an external vectored interrupt input pin and has a noise eliminator (See 6.3 Hardware Controlling Interrupt Function). 96 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-2. Ports 0, 1 Configuration SI SCK INT4 SO P01 output latch Selector 8 CSIM P-ch POGA bit 0 P00/INT4 P01/SCK P02/SO/SB0 P03/SI/SB1 Input buffer N-ch Output buffer where push-pull open-drain output and N-ch open-drain output buffer output can be switched VDD Selector Internal SCK VDD Pull-up resistors Internal bus Pull-up resistors P-ch POGA bit 1 Input buffer Φ or fX/64 Selector Noise eliminator P10/INT0 P11/INT1 P12/INT2/TI1/TI2 P13/TI0 TI0 INT2 INT1 INT0 TI1 TI2 Input buffer having hysteresis characteristic 97 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-3. Ports 3, 6 Configuration Key interrupt (only port 6) Input buffer having hysteresis characteristic (only port 6) Input buffer PMmn = 0 M P X Pull-up resistor PMmn = 1 POGA bit m P-ch VDD Internal bus Output latch Output buffer Pmn PMmn Corresponding bit of port mode register group A m = 3, 6 n = 0 through 3 Figure 5-4. Port 2 Configuration VDD Pull-up resistors P-ch POGA bit 2 Input buffer PM2=0 M P X PM2=1 Internal bus P20 P21 P22 P23 Output buffers PM2 Corresponding bit of port mode register group B Output latch 98 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-5. Port 5 Configuration VDD Pull-up resistors (Mask option) Input buffer PM5 = 0 M P X PM5 = 1 Internal bus P50 P51 Output latch P52 P53 N-ch open-drain output buffers PM5 Corresponding bit of port mode register group B 99 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-6. Ports 8, 9 Configuration VDD Pull-up resistors P-ch POGB bits 0,1 Input buffer PMm = 0 M P X PMm = 1 Internal bus Output buffers Pm0 Pm1 Pm2 Pm3 Output latch LPS Decoder PMm Corresponding bit of port mode register group C (m = 8, 9) To LCD controller/driver 100 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.1.2 Setting I/O mode The input or output mode of each I/O port is set by the corresponding port mode register as shown in Figure 5-7. Ports 3 and 6 can be set in the input or output mode in 1-bit units by using port mode register group A (PMGA). Ports 2 and 5 are set in the input or output mode in 4-bit units by using port mode register group B (PMGB). Port mode group register group C (PMGC) is used to set the input or output mode of ports 8 and 9 in 4-bit units. Each port is set in the input mode when the corresponding port mode register bit is “0” and in the output mode when the corresponding register bit is “1”. When a port is set in the output mode by the corresponding port mode register, the contents of the output latch are output to the output pin(s). Before setting the output mode, therefore, the necessary value must be written to the output latch. Port mode register groups A, B, and C are set by using an 8-bit memory manipulation instruction. When the RESET signal is asserted, all the bits of each port mode register are cleared to 0, turning off the output buffer and setting the corresponding port in the input mode. Example To use P30, 31, 62, and 63 as input pins and P32, 33, 60, and 61 as output pins CLR1 MOV MOV MBE XA, #3CH PMGA, XA ; or SEL MB15 101 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-7. Port Mode Register Formats Specification 0 1 Input mode (output buffer off) Output mode (output buffer on) Port mode register group A Address FE8H 7 6 5 4 3 2 1 0 Symbol PMGA P30 input/output specification P31 input/output specification P32 input/output specification P33 input/output specification P60 input/output specification P61 input/output specification P62 input/output specification P63 input/output specification PM63 PM62 PM61 PM60 PM33 PM32 PM31 PM30 Port mode register group B Address FECH 7 6 5 PM5 4 3 2 PM2 1 0 Symbol PMGB Port 2 (P20 to P23) input/output specification Port 5 (P50 to P53) input/output specification Port mode register group C Address FEEH Symbol PMGC Port 8 (P80 to P83) input/output specification Port 9 (P90 to P93) input/output specification 7 6 5 4 3 2 1 PM9 0 PM8 102 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.1.3 Digital I/O port manipulation instruction Because all the I/O ports of the µ PD753108 are mapped to the data memory space, they can be manipulated by using data memory manipulation instructions. Of these data memory manipulation instructions, those considered to be especially useful for manipulating the I/O pins and their range of applications are shown in Table 5-2. (1) Bit manipulation instruction Because the specific address bit direct addressing (fmem.bit) and specific address bit register indirect addressing (pmem.@L) are applicable to digital I/O ports 0 through 3, 5, 6, 8, and 9, the bits of these ports can be manipulated regardless of the specifications by MBE and MBS. Example To OR P50 and P51 and set P61 in output mode MOV1 OR1 MOV1 CY, PORT5.0 CY, PORT5.1 PORT6.1, CY ; CY ← P50 ; CY ← CY v P51 ; P61 ← CY (2) 4-bit manipulation instruction In addition to the IN and OUT instructions, all the 4-bit memory manipulation instructions such as MOV, XCH, ADDS, and INCS can be used to manipulate the ports in 4-bit units. Before executing these instructions, however, memory bank 15 must be selected. Examples 1. To output the contents of the accumulator to port 3 SET1 SEL OUT SET1 SEL MOV ADDS NOP MOV SET1 SEL MOV SUBS BR @HL, A MBE MB15 HL, #PORT5 A, @HL NO ; A < PORT5 ; NO ; YES ; PORT5 ← A 3. To test whether the data of port 5 is greater than the value of the accumulator MBE MB15 PORT3, A MBE MB15 HL, #PORT5 A, @HL ; A ← A+PORT5 ; or CLR1 MBE 2. To add the value of the accumulator to the data output to port 5 103 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (3) 8-bit manipulation instruction In addition to the IN and OUT instructions, the MOV, XCH, and SKE instructions can be used to manipulate ports 8 and 9, which can be manipulated in 8-bit units. In this case also, memory bank 15 must be selected, just as when 4-bit manipulation instructions are used to manipulate ports. Example To output the data of register pair BC to the output port specified by the 8-bit data input from ports 8 and 9 SET1 SEL IN MOV MOV MOV MBE MB15 XA, PORT8 HL, XA XA, BC @HL, XA ; XA ← ports 9 and 8 ; HL ← XA ; XA ← BC ; Port (L) ← XA 104 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Table 5-2. I/O Pin Manipulation Instructions PORT Instruction IN IN OUT OUT MOV MOV MOV MOV XCH XCH A, PORTn XA, PORTn PORTn, A PORTn, XA A, PORTn XA, PORTn PORTn, A PORTn, XA A, PORTn XA, PORTn Note 1 Note 1 Note 1 Note 1 Note 1 Note 1 Note 1 Note 1 Note 1 Note 1 PORT 0 PORT 1 PORT 2 PORT 3 PORT 5 PORT 6 PORT 8 PORT 9 √ — — — — — — √ √ √ √ √ √ — √ — — — √ — — — √ — — — MOV1 CY, PORTn. bit MOV1 CY, PORTn. @L MOV1 PORTn. bit, CY MOV1 PORTn. @L, CY Note 2 INCS SET1 SET1 CLR1 CLR1 SKT SKT SKF SKF PORTn PORTn. bit PORTn. @L PORTn. bit PORTn. @L PORTn. bit PORTn. @L PORTn. bit PORTn. @L Note 2 Note 2 Note 2 Note 2 Note 1 Note 2 √ √ — — — — √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ — — — — SKTCLR PORTn. bit SKTCLR PORTn. @L AND1 AND1 OR1 OR1 CY, PORTn. bit CY, PORTn. @L CY, PORTn. bit CY, PORTn. @L Note 2 Note 2 Note 2 XOR1 CY, PORTn. bit XOR1 CY, PORTn. @L Note 2 Notes 1. Must be MBE = 0 or (MBE = 1, MBS = 15) before execution. 2. The low-order 2 bits and the bit addresses of the address must be indirectly specified by the L register. 105 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.1.4 Operation of digital I/O port The operations of each port and port pin when a data memory manipulation instruction is executed to manipulate a digital I/O port differs depending on whether the port is set in the input or output mode (refer to Table 5-3). This is because, as can be seen from the configuration of the I/O port, the data of each pin is loaded to the internal bus in the input mode, and the data of the output latch is loaded to the internal bus in the output mode. (1) Operation in input mode When a test instruction such as SKT, a bit input instruction such as MOV1, or an instruction that loads port data to the internal bus, such as IN, MOV, an operation, or a comparison instruction, is executed, the data of each pin is manipulated. When an instruction that transfers the contents of the accumulator in 4- or 8-bit units, such as OUT or MOV, is executed, the data of the accumulator is latched to the output latch. The output buffer remains off. When the XCH instruction is executed, the data of each pin is input to the accumulator, and the data of the accumulator is latched to the output latch. The output buffer remains off. When the INCS instruction is executed, the data which 1 is added to the data of each pin (4 bits) is latched to the output latch. The output buffer remains off. When an instruction that rewrites the data memory contents in 1-bit units, such as SET1, CLR1, MOV1, or SKTCLR, is executed, the contents of the output latch of the specified bit can be rewritten as specified by the instruction, but the contents of the output latches of the other bits are undefined. (2) Operation in output mode When a test instruction, bit input instruction, or an instruction that loads port data to the internal bus is executed, the contents of the output latch are manipulated. When an instruction that transfers the contents of the accumulator in 4- or 8-bit units is executed, the data of the output latch is rewritten and at the same time output from the port pins. When the XCH instruction is executed, the contents of the output latch are transferred to the accumulator, and the contents of the accumulator are latched to the output latches of the specified port and output from the port pins. When the INCS instruction is executed, the contents of the output latches of the specified port are incremented by 1 and output from the port pins. When a bit output instruction is executed, the specified bit of the output latch is rewritten and output from the pin. 106 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Table 5-3. Operation When I/O Port Is Manipulated Operation of Port and Pins Instruction Executed SKT SKF MOV1 AND1 OR1 XOR1 IN IN MOV MOV MOV MOV ADDS ADDC SUBS SUBC AND OR XOR SKE SKE OUT OUT MOV MOV MOV MOV XCH XCH XCH XCH INCS INCS SET1 CLR1 MOV1 SKTCLR 1 1 Input Mode Tests pin data Transfers pin data to CY Performs operation between pin data and CY Output Mode Tests output latch data Transfers output latch data to CY Performs operation between output latch data and CY Transfers output latch data to accumulator CY, CY, CY, CY, 1 1 1 1 A, PORTn XA, PORTn A, PORTn XA, PORTn A, @HL XA, @HL A, A, A, A, A, A, A, @HL @HL @HL @HL @HL @HL @HL Transfers pin data to accumulator Performs operation between pin data and accumulator Performs operation between output latch data and accumulator A, @HL XA, @HL PORTn, A PORTn, XA PORTn, A PORTn, XA @HL, A @HL, XA A, PORTn XA, PORTn A, @HL XA, @HL PORTn @HL 1 1 1 1 Compares pin data with accumulator Transfers accumulator data to output latch (output buffer remains off) Compares output latch data with accumulator Transfers accumulator data to output latch and outputs data from pins Transfers pin data to accumulator and accumulator data to output latch (output buffer remains off) Increments pin data by 1 and latches it to output latch Rewrites output latch contents of specified bit as specified by instruction but output latch contents of other bits are undefined Exchanges data between output latch and accumulator Increments output latch contents by 1 Changes status of output pin as specified by instruction , CY Remark 1 : Indicates two addressing modes: PORTn.bit and PORTn.@L. 107 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.1.5 Connecting pull-up resistors Each port pin of the µ PD753108 can be connected to an internal pull-up resistor (except the P00 pin). Some pins can be connected with a pull-up resistor by software and the others can be connected by mask option. Table 5-4 shows how to specify connection of the pull-up resistor to each port pin. The on-chip pull-up resistor is connected by software in the format shown in Figure 5-8 . The on-chip pull-up resistor can be connected only to the pins of ports 3 and 6 in the input mode. To the pins set to output mode, the on-chip pull-up resistors cannot be connected regardless of the setting of POGA. Table 5-4. On-Chip Pull-Up Resistor Specification Method Port (Pin Name) PORT0 (P01 to P03) Note 1 Pull-up Resistor Specification Method Specifies to connect in 3-bit units by software. Specifies to connect in 4-bit units by software. Specified Bit POGA.0 POGA.1 POGA.2 POGA.3 Specifiable by mask option in 1-bit units. Specifies to connect in 4-bit units by software. — POGA.6 POGB.0 POGB.1 PORT1 (P10 to P13) PORT2 (P20 to P23) PORT3 (P30 to P33) PORT5 (P50 to P53) PORT6 (P60 to P63) PORT8 (P80 to P83) Note 2 PORT9 (P90 to P93) Note 2 Notes 1. The P00 pin cannot be specified to connect an on-chip pull-up resistor. 2. If these pins are used as segment outputs, do not specify to connect the on-chip pull-up resistor by software. Remark Pull-up resistor cannot be connected by mask option in the µ PD75P3116. 108 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-8. Pull-Up Resistor Specify Register Formats Specification 0 1 Disables on-chip pull-up resistor. Enables on-chip pull-up resistor. Pull-up resistor specify register group A Address FDCH Symbol POGA Port 0 (P01 to P03) Port 1 (P10 to P13) Port 2 (P20 to P23) Port 3 (P30 to P33) Port 6 (P60 to P63) 7 6 PO6 5 4 3 PO3 2 PO2 1 PO1 0 PO0 Pull-up resistor specify register group B Address FDEH Symbol POGB Port 8 (P80 to P83) Port 9 (P90 to P93) 7 6 5 4 3 2 1 PO9 0 PO8 109 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.1.6 I/O timing of digital I/O port Figure 5-9 shows the timing by which data is output to the output latch and the timing by which the pin data or the data of the output latch is loaded to the internal bus. Figure 5-10 shows the ON timing when an on-chip pull-up resistor is connected to a port pin via software. Figure 5-9. I/O Timing of Digital I/O Port (a) When data is loaded by 1-machine cycle instruction 1 machine cycle Instruction execution Input timing              Φ0 Φ1 Φ2 Φ3 Manipulation instruction (b) When data is loaded by 2-machine cycle instruction 2 machine cycles Instruction execution Input timing                           Φ0 Φ1 Φ2 Φ3 Manipulation instruction (c) When data is latched by 1-machine cycle instruction Φ3 Instruction execution Manipulation instruction Φ0 Φ1 Output latch (output pin) (d) When data is latched by 2-machine cycle instruction Φ0 Instruction execution Manipulation instruction Φ1 Output latch (output pin) 110 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-10. ON Timing of On-Chip Pull-up Resistor Connected via Software 2 machine cycles                           Φ0 Φ1 Instruction execution On-chip pull-up resistor setting instruction Pull-up resistor specify register 111 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.2 Clock Generator The clock generator supplies various clocks to the CPU and peripheral hardware units and controls the operation mode of the CPU. 5.2.1 Clock generator configuration The configuration of the clock generator is shown in Figure 5-11. Figure 5-11. Clock Generator Block Diagram XT1 VDD XT2 X1 VDD X2 Main system clock oscillator fX 1/1 to 1/4096 Divider 1/2 1/4 1/16 Subsystem clock oscillator fXT LCD controller/driver Watch timer · Basic interval timer (BT) · Timer/event counter · Serial interface · Watch timer · LCD controller/driver · INT0 noise eliminator · Clock output circuit Selector WM.3 SCC SCC3 Internal bus SCC0 PCC PCC0 PCC1 4 PCC2 HALTNote PCC3 STOPNote STOP F/F Q S R R Q Wait release signal from BT RESET signal Standby release signal from interrupt control circuit HALT F/F S Oscillation stop Selector Divider 1/4 Φ · CPU · INT0 noise eliminator · Clock output circuit PCC2, PCC3 Clear Note Instruction execution Remarks 1. fX = Main system clock frequency 2. fXT = Subsystem clock frequency 3. Φ = CPU clock 4. PCC: Processor Clock Control Register 5. SCC: System Clock Control Register 6. One clock cycle (tCY ) of the CPU clock is equal to one machine cycle of the instruction. 112 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.2.2 Clock generator function and operation The clock generator provides the following clock signals and controls the operating mode of the CPU such as standby mode. • • • • Main system clock Subsystem clock CPU clock fX fXT Φ Clock to peripheral hardware The clock generator operates according to how the processor clock control register (PCC) and system clock control register (SCC) are set, as described below: (a) When the RESET signal is generated, the minimum speed mode of the main system clock (10.7 µ s at 6.00MHz operation) is selected (PCC = 0 and SCC = 0). (b) When the main system clock is selected, one of four CPU clock frequencies can be selected (0.67 µ s, 1.33 µ s, 2.67 µ s, and 10.7 µ s at 6.00-MHz operation) by setting PCC. (c) When the main system clock is selected, the standby mode (STOP or HALT) can be used. (d) Subsystem clock is selected by setting SCC, and operation can be performed at a very low-speed and low current consumption (122 µ s at 32.768-kHz operation). In this case, the PCC setup value does not affect the CPU clock. (e) When the subsystem clock is selected, main system clock oscillation can be stopped by setting SCC. The HALT mode can also be used, but the STOP mode cannot be used (Subsystem clock oscillation cannot be stopped). (f) The main system clock is divided to generate a clock supplied to peripheral hardware. The subsystem clock can be supplied directly only to the watch timer. Thus, the watch function and the LCD controller/driver and buzzer output function which operate using the watch timer clocks can also continue operation in the standby mode. (g) When the subsystem clock is selected, the watch timer and LCD controller/driver can continue normal operation. The serial interface and timer/event counter can continue the operation when they have selected an external clock as a clock. However, the other hardware operate with the main system clock, therefore it cannot be used when the main system clock stops. 113 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (1) Processor clock control register (PCC) The PCC is a 4-bit register whereof the low-order 2 bits select the CPU clock Φ and high-order 2 bits control the CPU operating mode (See Figure 5-12). When bit 2 or bit 3 is set to “1” exclusively, the PCC is set in the standby mode. When it is released from the mode by a standby release signal, both bits 2 and 3 are automatically cleared for normal operations (See CHAPTER 7 STANDBY FUNCTION ). The low-order 2 bits of the PCC are set by a 4-bit memory manipulation instruction (The high-order 2 bits must be set to “0”). Bits 2 and 3 are set to “1” by a HALT instruction and STOP instruction, respectively. These instructions can be executed regardless of the contents of MBE. The CPU clock can be selected only when the PCC operates with the main system clock. When it operates with a subsystem clock, its low-order 2 bits are invalidated and the frequency is fixed to fXT/4. The STOP instruction can be executed only when the PCC operates with the main system clock. Examples 1. The machine cycle is set to the fastest mode (0.67 µ s: during 6.00-MHz operation). SEL MOV MOV MB15 A, #0011B PCC, A 2. The machine cycle is set to 1.91 µs at 4.19 MHz. SEL MOV MOV MB15 A, #0010B PCC, A 3. The PCC is set to the STOP mode (An NOP instruction must be entered following the STOP instruction or HALT instruction). STOP NOP The PCC is cleared to “0” by the RESET signal. 114 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-12. Processor Clock Control Register Format Address FB3H 3 PCC3 2 1 0 PCC0 Symbol PCC PCC2 PCC1 CPU clock selection bit (When fX = 6.0 MHz) SCC3, SCC0 = 00 Values in Parentheses Are Applied When fX = 6.0 MHz CPU Clock Frequency 0 0 1 1 0 1 0 1 Φ = fX/64 (93.8 kHz) Φ = fX/16 (375 kHz) Φ = fX/8 (750 kHz) Φ = fX/4 (1.5 MHz) 1 Machine Cycle 10.7 µ s 2.67 µ s 1.33 µ s 0.67 µ s SCC3, SCC0 = 01 or 11 Values in Parentheses Are Applied When fXT = 32.768 kHz CPU Clock Frequency 1 Machine Cycle Φ = fXT/4 (8.192 kHz) 122 µ s (When fX = 4.19 MHz) SCC3, SCC0 = 00 Values in Parentheses Are Applied When fX = 4.19 MHz CPU Clock Frequency 0 0 1 1 0 1 0 1 Φ = fX/64 (65.5 kHz) Φ = fX/16 (262 kHz) Φ = fX/8 (524 kHz) Φ = fX/4 (1.05 MHz) SCC3, SCC0 = 01 or 11 Values in Parentheses Are Applied When fXT = 32.768 kHz 1 Machine Cycle 122 µ s 1 Machine Cycle CPU Clock Frequency 15.3 µ s 3.81 µ s 1.91 µ s 0.95 µ s Φ = fXT/4 (8.192 kHz) Remarks 1. fX : Main system clock oscillator output frequency 2. fXT : Subsystem clock oscillator output frequency CPU operating mode control bits 0 0 1 1 0 1 0 1 Normal operation mode HALT mode STOP mode Setting prohibited 115 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (2) System clock control register (SCC) The system clock register (SCC) is a 4-bit register whose least significant bit is used to select CPU clock Φ, and the most significant bit is used to control (stop) main system clock oscillation (See Figure 5-13). SCC.0 and SCC.3 exist at the same data memory address, but cannot be changed at the same time. Thus, SCC.0 and SCC.3 are set by using a bit manipulation instruction. SCC.0 and SCC.3 can always be operated independently of the MBE contents. Main system clock oscillation can be stopped by setting SCC.3 only during subsystem clock operation. Main system clock oscillation is stopped by using the STOP instruction during main system clock operation. When the RESET signal is generated, SCC is cleared to “0”. Figure 5-13. System Clock Control Register Format Address FB7H 3 SCC3 2 – 1 – 0 SCC0 Symbol SCC SCC3 SCC0 0 0 1 1 0 1 0 1 CPU Clock Selection Main system clock Subsystem clock Setting prohibited Subsystem clock Main System Clock Oscillation Oscillation is enabled. Oscillation is stopped. Cautions 1. Changing the system clock requires a maximum of 1/fXT time. To stop main system clock after changing the subsystem clock, set SCC. 3 to 1 after the machine cycle or cycles listed in Table 5-5 had elapsed. 2. Even if oscillation is stopped by setting SCC. 3 during main system clock operation, normal STOP mode is not entered. 3. When “1” is set to SCC.3, the X2 pin is internally pulled up to VDD with the resistor of 50 kΩ (TYP.). 116 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (3) System clock oscillators The main system clock oscillator oscillates with a crystal resonator or ceramic resonator connected to the X1 and X2 pins (4.194304 MHz TYP.). External clock can also be input. Figure 5-14. Main System Clock Oscillator External Circuit (a) Crystal or ceramic oscillation VDD (b) External clock µ PD753108 External clock X1 µ PD753108 X1 X2 VDD Crystal or ceramic resonator X2 The subsystem clock oscillator oscillates with a crystal resonator connected to the XT1 and XT2 pins (32.768 kHz TYP.). External clock can also be input. Figure 5-15. Subsystem Clock Oscillator External Circuit (a) Crystal oscillation VDD (b) External clock µ PD753108 External clock XT1 µ PD753108 XT1 XT2 VDD Crystal resonator XT2 117 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Cautions 1. When the STOP mode is set, the X2 pin is internally pulled up to VDD with the resistor of 50 kΩ (TYP.). 2. Wire the portion enclosed by broken lines in Figures 5-14 and 5-15 as follows to prevent adverse influence by wiring capacitance when using the main system clock and subsystem clock oscillation circuits. • Keep the wiring length as short as possible. • Do not cross the wiring with any other signal lines. • Do not route the wiring in the vicinity of a line through which a high alternating current flows. • Always keep the potential at the connecting point of the capacitor of the oscillation circuit at the same level as V DD. Do not connect the wiring to power supply lines through which a high current flows. • Do not extract signals from the oscillation circuit. The amplification factor of the subsystem clock oscillation circuit is kept low to reduce the power dissipation, and therefore it is more susceptible to noise than the main system clock oscillation circuit. therefore, exercise care in wiring. Figure 5-16 shows examples of connecting the resonator incorrectly. Figure 5-16. Example of Connecting Resonator Incorrectly (1/2) (a) Wiring length too long (b) Crossed signal line To use the subsystem clock oscillation circuit, PORTn ( n = 0 to 3, 5, 6, 8, 9) µ PD753108 VDD X2 X1 VDD µ PD753108 X2 X1 VDD VDD Remark When using the subsystem clock, take X1 and X2 in the above figures as XT1 and XT2. Also, connect a resistor in series with XT2. 118 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-16. Example of Connecting Resonator Incorrectly (2/2) (c) High alternating current close to signal line (d) Current flowing through power line of oscillation circuit (potential at points A, B, and C changes) VDD µPD753108 µ PD753108 Pnm VDD X2 X1 VDD X2 X1 High current VDD VDD A B C High current (e) Signal extracted (f) Main system clock and subsystem clock signal lines close and parallel to each other µPD753108 µ PD753108 VDD X2 X1 VDD X2 X1 XT2 XT1 VDD VDD XT2 and X1 are wired in parallel. Remark When using the subsystem clock, take X1 and X2 in the above figures as XT1 and XT2. Also, connect a resistor in series with XT2. 119 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Cautions 3. In Figure 5-16 (f), XT2 and X1 are wired in parallel. In consequence, the crosstalk noise of X1 may be superimposed on XT2, causing malfunctioning. To avoid the malfunctioning, do not wire XT2 and X1 in parallel, and connect the IC pin between XT2 and X1 pins to VDD. µ PD753108 VDD X2 X1 IC XT2 XT1 VDD (4) Divider circuit The divider circuit divides the output of the main system clock oscillation circuit (fX ) to generate various clocks. 120 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (5) Subsystem clock oscillator control functions The µ PD753108 subsystem clock oscillator has the following two control functions. • Selects by software whether an on-chip feedback resistor is to be used or not Note. • Reduces current consumption by decreasing the drive current of the on-chip inverter when the supply voltage is high (V DD ≥ 2.7 V). Note When not using the subsystem clock, set SOS.0 to 1 (disable the on-chip feedback resistor) via software, connect XT1 to V SS or VDD, and leave XT2 open. This reduces the current consumption in the subsystem clock oscillator. The above functions can be used by switching the bits 0 and 1 of the subsystem clock oscillator control register (SOS) (See Figure 5-17). Figure 5-17. Subsystem Clock Oscillator SOS.0 Feedback resistor Inverter SOS.1 XT1 XT2 µ PD753108 VDD 121 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (6) Subsystem clock oscillator control register (SOS) The SOS selects whether to use the on-chip feedback resistor or not and controls the drive current of the onchip inverter (See Figure 5-18). When the RESET signal is asserted, all the bits of this register are cleared to 0. The function of each flag of the SOS register is described below. (a) SOS.0 (feedback resistor cut flag) Whether or not to use the on-chip feedback resistor can be selected by software by setting SOS.0 in the µPD753108 . If no resonator is used, the current consumption can be reduced by setting SOS.0 to “1” to turn off the feedback circuit. If a resonator is used, be sure to set “0” (feedback circuit turned on). (b) SOS.1 (drive capability switching flag) The on-chip inverter of the µPD753108’s subsystem clock oscillator is designed to operate with a low supply voltage (VDD = 1.8 V possible) and so its drive current is large. When it is used with a high supply voltage (VDD ≥ 2.7 V), its supply current becomes too large. In this case, the supply current can be decreased by reducing the drive current of the inverter by setting the SOS.1 to “1”. Note if it is set to “1” at the time VDD is less than 2.7 V, the oscillator may stop oscillation due to too small a drive current. When VDD of less than 2.7 V is used, SOS.1 must be set to “0”. 122 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-18. Subsystem Clock Oscillator Control Register (SOS) Format Address FCFH 3 0 2 0 1 0 Symbol SOS SOS1 SOS0 Subsystem clock oscillator feedback resistor cut flag 0 1 On-chip feedback resistor is used. On-chip feedback resistor is not used. Subsystem clock oscillator current cut flag 0 1 Drive current is large (1.8 V ≤ VDD). Drive current is small (2.7 V ≤ VDD). Bits 2 and 3 of SOS must be set to “0”. Remark When the subsystem clock is not necessary, set the XT1 and XT2 pins and SOS register as follows: XT1 : Connect to VSS or VDD XT2 : Open SOS : 00X1B (X: don’t care) 123 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.2.3 Setting of system clock and CPU clock (1) Time required to switch system clock to/from CPU clocks The system and CPU clocks can be switched by using the low-order two bits of PCC and the least significant bit of SCC. However, this clock switching is not immediately made after the registers are rewritten, and the clock before the clock switching is made is used for operation during given machine cycles. Thus, to stop main system clock oscillation, execute a STOP instruction or set bit 3 of SCC after switching the time elapses. Table 5-5. Maximum Time Required to Switch System to/from CPU Clocks Setup Value before Switching Setup Value after Switching SCC0 PCC1 PCC0 SCC0 PCC1 PCC0 SCC0 PCC1 PCC0 SCC0 PCC1 PCC0 SCC0 PCC1 PCC0 SCC0 PCC1 PCC0 0 0 0 0 0 0 0 0 1 0 1 0 0 1 1 1 1 machine cycle 1 machine cycle 1 machine cycle × × fX machine 64fXT cycles (3 machine cycles) 0 1 4 machine cycles 4 machine cycles 4 machine cycles fX machine 16fXT cycles (12 machine cycles) 1 0 8 machine cycles 8 machine cycles 8 machine cycles fX 8fXT machine cycles (23 machine cycles) 1 1 16 machine cycles 16 machine cycles 16 machine cycles fX 4fXT machine cycles (46 machine cycles) 1 × × 1 machine cycle 1 machine cycleNote 1 machine cycle 1 machine cycle Note Emulation cannot be performed by tools. Caution The values of fX and fXT change depending on the environmental temperature of the resonator and the variance of load capacitance characteristics. When fX is higher than its nominal value or fXT is lower than its nominal value, the machine cycles obtained by the formulae fX /64fXT, f X/16f XT, f X/8fXT, and fX /4fXT given in the table are larger than those obtained by the nominal values of fX and fXT. Thus, when setting a wait time necessary for switching the system clock to/from CPU clock, it must be longer than the machine cycle obtained by the nominal values of fX and fXT. Remarks 1. ( ): fX = 6.0 MHz, f XT = 32.768 kHz 2. ×: don’t care 3. The CPU clock Φ is supplied to the internal CPU and its inverse (defined to be 1 machine cycle in this manual) is the minimum instruction execution time. 124 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (2) Switching procedure between system clock and CPU clock The switching procedure between the system clock and CPU clock is explained according to Figure 5-19. Figure 5-19. Switching between System Clock and CPU Clock On Line voltage Off Lowest operating power voltage Voltage at VDD pin RESET signal WaitNote System clock, CPU clock fX 10.7 µ s Internal reset operation fX = 6.0 MHz fXT = 32.768 kHz                                     fX 0.67 µ s fXT 122 µ s fX 0.67 µ s After the wait time Note has elapsed for stable oscillation by the RESET signal, the CPU starts operation with the slowest speed (10.7 µs: 6.0-MHz operation, 15.3 µ s: 4.19-MHz operation) of the main system clock. After a time long enough for the voltage at the V DD pin to rise to a value by which the CPU can operate in the highest speed has elapsed, the contents of the PCC are written and the CPU starts operation in the highest speed. The failure of the line voltage is detected by an interrupt input (INT4) to set bit 0 of the SCC to “1”, and then the CPU starts operation with the subsystem clock. At this time, the subsystem clock must have started oscillation. After the time necessary to switch to the subsystem clock (46 machine cycles) has elapsed, bit 3 of the SCC is set to “1” and then the main system clock stops oscillation. The recovery of the line voltage is detected by an interrupt, and then bit 3 of the SCC is cleared to “0” to make the main system clock start oscillation. After the time necessary for stable oscillation has elapsed, bit 0 of the SCC is cleared to “0” and the CPU operates in the highest speed. Note The following two wait times can be selected by mask option. 2 17/f X (21.8 ms: 6.0-MHz operation, 31.3 ms: 4.19-MHz operation) 2 15/f X (5.46 ms: 6.0-MHz operation, 7.81 ms: 4.19-MHz operation) The µ PD75P3116 provides no mask options and the wait time is fixed to 2 15/f X. 125 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.2.4 Clock output circuit (1) Clock output circuit configuration The configuration of the clock output circuit is shown in Figure 5-20. (2) Clock output circuit function The clock output circuit is provided to output the clock pulses from the PCL/P22/PTO2 pin to the remote control waveform output application and peripheral LSI’s. The clock pulses must be output in the following steps. (a) Select a clock output frequency. Prohibit clock output. (b) Write “0” in the output latch at P22. (c) Set the I/O mode of the port 2 to output. (d) Disable the timer/event counter (channel 2) output. (e) Enable clock output. Figure 5-20. Clock Output Circuit Block Diagram From clock generator Φ fX/23 Selector fX/24 fX/26 From timer/event counter (Channel 2) Selector Output buffer PCL/P22/PTO2 PORT2.2 CLOM3 0 CLOM1 CLOM0 CLOM P22 output latch Bit 2 of PMGB Port 2 I/O mode specification bit 4 Internal bus Remark Special care has been taken in designing the chip so that small-width pulses may not be output when switching clock output enable/disable. 126 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (3) Clock output mode register (CLOM) The CLOM is a 4-bit register which controls clock output. It must be set by a 4-bit memory manipulation instruction. Example The CPU clock Φ is output from the PCL/P22/PTO2 pin. SEL MOV MOV MB15 A, #1000B CLOM, A ; or CLR1 MBE CLOM is cleared to “0” by a RESET signal generation and the clock output is disabled. Figure 5-21. Clock Output Mode Register Format Address FD0H Symbol 3 CLOM3 2 0 1 0 CLOM1 CLOM0 CLOM Clock output frequency select bit When fX = 6.00 MHz 0 0 1 1 0 1 0 1 Φ output Note (1.5 MHz, 750 kHz, 375 kHz, 93.8 kHz) fX/23 output (750 kHz) fX/24 output (375 kHz) fX/26 output (93.8 kHz) When fX = 4.19 MHz 0 0 1 1 0 1 0 1 Φ outputNote (1.05 MHz, 524 kHz, 262 kHz, 65.5 kHz) fX/23 output (524 kHz) fX/24 output (262 kHz) fX/26 output (65.5 kHz) Note Φ is the CPU clock selected by the PCC. Clock output enable/disable bit 0 1 Output disabled. Output enabled. Caution Be sure to set bit 2 of the CLOM to “0”. 127 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (4) Application example of remote control waveform output The µ PD753108 clock output function can be used for remote control waveform output. The carrier frequency of remote control waveform output is selected by the clock frequency select bit of the clock output mode register. The pulse output enable/disable is selected by controlling the clock output enable/disable bit by software. Special attention is paid not to output small-width pulses when switching clock output enable/disable. Figure 5-22. Application Example of Remote Control Waveform Output CLOM bit 3 PCL pin output 128 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.3 Basic Interval Timer/Watchdog Timer The µ PD753108 is provided with the 8-bit basic interval timer/watchdog timer and has the following functions. (a) Interval timer operation to generate a reference time interrupt (b) Watchdog timer operation to detect a runaway of program and reset the CPU (c) Selects and counts the wait time when the standby mode is released (d) Reads the contents of counting 5.3.1 Basic interval timer/watchdog timer configuration The configuration of the basic interval timer/watchdog timer is shown in Figure 5-23. Figure 5-23. Basic Interval Timer/Watchdog Timer Block Diagram From clock generator fX/25 fX/27 MPX fX/29 fX/212 3 BT Clear Clear BT interrupt request flag IRQBT Basic interval timer (8-bit frequency divider) Set Vectored interrupt request signal BTM3 BTM2 BTM1 BTM0 BTM SET1Note 4 8 Internal bus Wait release signal when standby is released Internal reset signal WDTM SET1Note 1 Note Instruction execution 129 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.3.2 Basic interval timer mode register (BTM) The BTM is a 4-bit register which controls the operations of the basic interval timer (BT). It is set by a 4-bit memory manipulation instruction. Bit 3 can be set by a bit manipulation instruction. Example The interrupt generation interval is set to 1.37 ms (6.00 MHz). SEL CLR1 MOV MOV MB15 WDTM A, #1111B BTM, A ; BTM ← 1111B ; or CLR1 MBE When bit 3 is set to “1”, the contents of BT are cleared and the interrupt request flag of the basic interval timer/ watchdog timer (IRQBT) is also cleared (the start of the basic interval timer/watchdog timer). Its contents are cleared to “0” by a RESET signal generation and the interrupt request signal generation interval is set to the longest time. 130 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-24. Basic Interval Timer Mode Register Format Address 3 F85H 2 1 0 BTM BTM3 BTM2 BTM1 BTM0 Symbol When fX = 6.00 MHz Clock Input Specification 0 0 1 1 0 1 0 1 0 1 1 1 fX/212 (1.46 kHz) fX/29 (11.7 kHz) fX/27 (46.9 kHz) fX/25 (188 kHz) Setting prohibited Interrupt Interval Time (Wait Time When Standby Is Released) 220/fX (175 ms) 217/fX (21.8 ms) 215/fX (5.46 ms) 213/fX (1.37 ms) – Other than the above When fX = 4.19 MHz Clock Input Specification 0 0 1 1 0 1 0 1 0 1 1 1 fX/212 (1.02 kHz) fX/29 (8.19 kHz) fX/27 (32.768 kHz) fX/25 (131 kHz) Setting prohibited Interrupt Interval Time (Wait Time When Standby Is Released) 220/fX (250 ms) 217/fX (31.3 ms) 215/fX (7.81 ms) 213/fX (1.95 ms) – Other than the above Start control bit of basic interval timer/watchdog timer The basic interval timer/watchdog timer starts by writing “1” (The counter and interrupt request flag are cleared). Reset to "0" automatically when the operation starts. 131 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.3.3 Watchdog timer enable flag (WDTM) The WDTM is a flag which enables reset signal generation by overflow. It is set by a bit manipulation instruction. Once it is set, it cannot be cleared by an instruction. Example Setting of watchdog timer SEL MB15 ; or CLR1 MBE SET1 . WDTM . . . SET1 BTM.3 ; Bit 3 of BTM is set to “1”. The contents are cleared to “0” by a RESET signal generation. Figure 5-25. Watchdog Timer Enable Flag (WDTM) Format Address F8BH.3 WDTM 0 BT mode: Sets the IRQBT by the overflow of basic interval timer (BT). WT mode: Generates an internal reset signal by the overflow of basic interval timer (BT). 1 132 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.3.4 Basic interval timer operations When WDTM is set to “0”, the interrupt request flag (IRQBT) is set by the overflow of the basic interval timer (BT) and it operates as the interval timer. The basic interval timer (BT) always increments by the clock sent from the clock generator and the counting operation cannot be stopped. Four interrupt generation intervals can be set by BTM (See Figure 5-24). By setting bit 3 of the BTM to “1”, the basic interval timer (BT) and IRQBT can be cleared (start specification as the interval timer). The counting status can be read out from the basic interval timer (BT) by an 8-bit manipulation instruction. Note that data cannot be entered. Perform the timer operations as follows (These can be set at the same time). Set an interval time to the BTM. Set bit 3 of BTM to “1”. Example Interrupts are generated every 1.37 ms (during 6.00-MHz operation). SET1 SEL MOV MOV EI EI IEBT MBE MB15 A, #1111B BTM, A ; Time setting and start ; Interrupt enabled ; BT interrupt enabled 133 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.3.5 Watchdog timer operations When WDTM is set to “1” in the basic interval timer/watchdog timer, it performs as the watchdog timer wherein an internal reset signal is generated by an overflow of the basic interval timer (BT). No reset signal, however, is generated during the oscillation wait time following the STOP instruction has been released (When the WDTM is set to “1” once, it can be cleared only by resetting). The basic interval timer (BT) always increments by the clock sent from the clock generator and its counting operation cannot be stopped. In the watchdog timer mode, program runaway is detected by utilizing the interval time wherein the BT overflows. Four intervals can be selected by bits 0 to 2 of the BTM (See Figure 5-24). Select one of them suitable for user’s system. Set an interval and divide the program so that it can be executed in the interval and execute the instruction which clears the BT at the ends of the divided program. If the instruction which clears the BT is not reached within the time set (that is, the program is not executed normally = runaway), the BT overflows and an internal reset signal is generated to forcibly terminate the program. Namely, it indicates a program runaway has occurred and been detected. Set the watchdog timer with the following procedure ( and can be set at the same time). Set the interval in the BTM. Set bit 3 of the BTM to “1”. Set WDTM to “1”. Then, set bit 3 of the BTM to “1” within the interval. Initialization 134 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Example The basic interval timer/watchdog timer is used as the watchdog timer with 5.46 ms (during 6.00MHz operation). The program is divided into several modules which end within the time set for the BTM (5.46 ms) and the BT is cleared at the ends of the modules. In case a runaway occurs, the BT is not cleared within the time set, therefore it overflows and an internal reset signal is generated. Initialization : SET1 SEL MOV MOV SET1 ... MBE MB15 A, #1101B BTM, A WDTM : Sets time and starts : Enables watchdog timer (Then, the bit 3 of the BTM is set to “1” every 5.46 ms.) Module 1 : ...... SET1 SEL SET1 MBE MB15 BTM.3 Processing is completed within 5.46 ms. Module 2 : SET1 SEL SET1 ... ...... MBE MB15 BTM.3 Processing is completed within 5.46 ms. 135 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.3.6 Other functions The basic interval timer/watchdog timer has the following functions regardless of the basic interval timer (BT) operation and watchdog timer operation. Selects and counts the wait time after the standby mode is released. Reads the contents of counter. (1) Selects and counts the wait time after the STOP mode is released At the time the STOP mode is released, the system clock needs time for stabilizing oscillation. For this purpose, the wait function is provided for the CPU to halt its operation until the basic interval timer (BT) overflows. The wait time after a RESET signal generation is fixed by the mask option. However, it can be selected by setting the BTM when the STOP mode is released by an interrupt generated. In this case, the wait time is the same as the interval shown in Figure 5-24. The BTM must be set before the STOP mode is set. For details, refer to CHAPTER 7 STANDBY FUNCTION . Example The wait time is set to 5.46 ms at the time the STOP mode is released by an interrupt (during 6.00-MHz operation). SET1 SEL MOV MOV STOP NOP (2) Reads the counting operation The basic interval timer (BT) can read the counting status by an 8-bit manipulation instruction. Note that data cannot be entered. Caution When reading the counting contents of the BT, execute the read instruction twice in order not to read uncertain data while counting continues. If the two values read out are reasonable, take the last one as the count data. If they are completely different, try the operation again. MBE MB15 A, #1101B BTM, A ; Sets time ; Sets the STOP mode 136 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Examples 1. The counting contents of the BT is read out. SET1 SEL MOV LOOP : MOV MOV MOV SKE BR MBE MB15 HL, #BT XA, @HL BC, XA XA, @HL XA, BC LOOP ; Second reading ; Sets the address of BT to HL. ; First reading 2. The high-level width of the pulses which are input to an INT4 interrupt (both edges are detected) is set. The pulse width is assumed not to exceed the value set for the BT. The value set for the BTM is assumed to be 5.46 ms or more (during 6.00-MHz operation). LOOP : MOV MOV MOV SKE BR MOV SKE BR SKT BR MOV MOV CLR1 RETI AA : MOV MOV SUBC INCS MOV MOV SUBC MOV MOV MOV SET1 RETI HL, #BUFF A, C A, @HL L C, A A, B A, @HL B, A XA, BC BUFF, XA FLAG ; Stores data ; Data exists. Sets the flag. XA, BT BC, XA XA, BT A, C LOOP A, X A, B LOOP PORT0.0 AA XA, BC BUFF, XA FLAG ; Data exists. Clears the flag. ; P00 = 1? ; NO ; Stores data in the data memory ; First reading ; Stores data ; Second reading 137 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.4 Watch Timer The µ PD753108 is provided with a 1-channel of watch timer. This watch timer has the following functions: (a) Sets the test flag (IRQW) with 0.5 sec interval. The standby mode can be released by the IRQW. (b) 0.5 sec interval can be created by both the main system clock and subsystem clock. Take f X = 4.194304 MHz for the main system clock frequency and fXT = 32.768 kHz for the subsystem clock. (c) Convenient for program debugging and checking as interval becomes 128 times longer (3.91 ms) with the fast feed mode. (d) Outputs the frequencies (2.048, 4.096, 32.768 kHz) to the P23/BUZ pin, usable for buzzer and trimming of system clock frequencies. (e) Clears the frequency divider to make the clock start with zero seconds. 5.4.1 Configuration of watch timer Figure 5-26 shows the configuration of the watch timer. 138 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-26. Watch Timer Block Diagram fW (512 Hz : 1.95 ms) 26 fW (256 Hz : 3.91 ms) 27 fX 128 (32.768 kHz) Selector fXT (32.768 kHz) fLCD From clock generator fW (32.768 kHz) 4 kHz 2 kHz fW fW 23 24 Divider fW 214 2 Hz 0.5 sec. Selector INTW IRQW set signal Clear Selector Output buffer P23/BUZ WM WM7 0 WM5 WM4 WM3 WM2 WM1 WM0 PORT2.3 P23 output latch PMGB bit 2 Port 2 input/ output mode 8 Bit test instruction Internal bus Remark The values enclosed in parentheses are applied when fX = 4.194304 MHz and f XT = 32.768 kHz. 5.4.2 Watch mode register The watch mode register (WM) is an 8-bit register which controls the watch timer. Its format is shown in Figure 5-27. The watch mode register (WM) is set by an 8-bit manipulation instruction except for bit 3. It is provided for testing the input level at the XT1 pin. Data cannot be entered via the pin. All the bits except for bit 3 are cleared to “0” by a RESET signal generation. Example Make a time by the main system clock (4.19 MHz). Enable buzzer output. CLR1 MOV MOV MBE XA, #84H WM, XA ; Sets the WM 139 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-27. Format of Watch Mode Register Address F98H 7 WM7 6 0 5 WM5 4 WM4 3 WM3 2 WM2 1 WM1 0 WM0 Symbol WM BUZ output enable/disable bit WM7 0 1 Disables BUZ output. Enables BUZ output. BUZ output frequency select bit WM5 0 0 1 1 WM4 0 1 0 1 BUZ output frequency fW 24 fW 23 (2.048 kHz) (4.096 kHz) Setting prohibited. fW (32.768 kHz) Input level to XT1 pin (only bit test is possible) WM3 0 1 Input to XT1 pin is low level. Input to XT1 pin is high level. Watch operation enable/disable bit WM2 0 1 Stops watch operation (clears the frequency divider). Watch operation possible. Operation mode select bit WM1 0 1 Normal watch mode ( fW : sets the IRQW in 0.5 sec). 214 fW Fast watch mode ( 7 : sets the IRQW in 3.91 ms). 2 Count clock (fW) select bit WM0 0 1 Frequency divided output of system clock: selects fX 128 Subsystem clock: selects fXT Remark The function in parentheses is available when fW = 32.768 kHz. 140 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.5 Timer/Event Counter The µ PD753108 has three channels of timer/event counters. The timer/event counter has the following functions. (a) Programmable interval timer operation (b) Square wave output of any frequency to the PTOn pin. (c) Event counter operation (d) Divides the frequency of signal input via the TIn pin to 1-Nth of the original signal and outputs the divided frequency to the PTOn pin (frequency divider operation). (e) Supplies the serial shift clock to the serial interface circuit (for channel 0 only). (f) Calls the counting status. The timer/event counter operates in the following four modes as set by the mode register. Table 5-6. Operation Modes of Timer/Event Counter Channel Mode 8-bit timer/event counter mode Gate control function PWM pulse generator mode 16-bit timer/event counter mode Gate control function Carrier generator mode Channel 0 Usable n/aNote n/a n/a n/aNote n/a Channel 1 Usable n/a n/a Channel 2 Usable Usable Usable Usable Usable Usable Note Used for gate control signal generation 5.5.1 Configuration of timer/event counter Figures 5-28 to 5-30 show the configuration of the timer/event counter. 141 142 8 – PORT1.3 Input buffer TI0/P13 From clock generator fX/24 fX/26 fX/28 fX/210 MPX Figure 5-28. Timer/Event Counter (Channel 0) Block Diagram Internal bus SET1Note TM0 TM06 TM05 TM04 TM03 TM02 – – 8 8 TMOD0 Modulo register (8) TOE0 T0 enable flag P20 output latch PORT2.0 PMGB bit 2 Port 2 input/output mode To serial interface CHAPTER 5 8 Comparator (8) 8 Reset T0 Count register (8) CP Clear Match TOUT F/F TOUT0 P20/PTO0 Output buffer PERIPHERAL HARDWARE FUNCTION INTT0 IRQT0 set signal Timer operation start RESET IRQT0 clear signal To timer/event counter (channel 2) Note Instruction execution Figure 5-29. Timer/Event Counter (Channel 1) Block Diagram Internal bus 8 – SET1Note TM1 8 TMOD1 PORT1.2 Decoder Modulo register (8) CHAPTER 5 8 Match Input buffer TI1/TI2/P12/INT2 Timer/event counter output (channel 2) TOE1 T1 enable flag PORT2.1 P21 output latch PMGB bit 2 TM16 TM15 TM14 TM13 TM12 TM11 TM10 Port 2 input/output mode Comparator (8) 8 MPX CP Count register (8) Clear T1 TOUT F/F Reset P21/PTO1 Output buffer PERIPHERAL HARDWARE FUNCTION From clock generator fX/2 fX/26 fX/28 fX/210 fX/212 5 RESET Timer operation start 16 bit timer/event counter mode Selector IRQT1 clear signal Timer/event counter match signal (channel 2) (When 16-bit timer/event counter mode) Timer/event counter reload signal (channel 2) INTT1 IRQT1 set signal Timer/event counter comparator (channel 2) (When 16-bit timer/event counter mode) Note Instruction execution 143 Selector Selector TI1/TI2/ P12/INT2 From clock generator fX fX/2 fX/24 fX/26 fX/28 fX/210 MPX CP T2 Count register (8) Clear 8 Reset Overflow Carrier generator mode Selector 144 8 SET1Note PORT1.2 Input buffer Figure 5-30. Timer/Event Counter (Channel 2) Block Diagram Internal bus 8 TMOD2H TM2 TM26 TM25 TM24 TM23 TM22 TM21 TM20 High-level period setting modulo register (8) 8 8 TC2 TOE2 REMC NRZB NRZ Reload TMOD2 Modulo register (8) TGCE 8 8 Decoder MPX (8) 8 PORT2.2 PMGB bit 2 P22 Port 2 output latch input/output CHAPTER 5 P22/PCL/ PTO2 Match Comparator (8) TOUT F/F Output buffer Timer/event counter clock input (channel 1) PERIPHERAL HARDWARE FUNCTION 16-bit timer/event counter mode INTT2 IRQT2 set signal IRQT2 clear signal Timer operation start RESET Timer event counter TOUT F/F (channel 0) Timer/event counter clear signal (channel 1) (When 16-bit timer/event counter mode) Timer/event counter match signal (channel 1) (When carrier generator mode) From clock generator Timer/event counter match signal (channel 1) (When 16-bit timer/event counter mode) Note Instruction execution CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (1) Timer/event counter mode register (TM0, TM1, TM2) The mode register (TMn) is an 8-bit register which controls the timer/event counter. Its format is shown in Figures 5-31 to 5-33. The timer/event counter mode register is set by an 8-bit memory manipulation instruction. Bit 3 is a timer start bit and can be operated bit-wise. It is automatically reset to “0” when the timer operation starts. All the bits of the timer/event counter mode register are cleared to “0” by a RESET signal generation. Examples 1. Start the timer in the interval timer mode of CP = 5.86 kHz (during 6.00-MHz operation). SEL MOV MOV MB15 XA, #01001100B TMn, XA ; TMn ← 4CH ; or CLR1 MBE 2. Restart the timer according to the setting of the timer/event counter mode register. SEL SET1 MB15 TMn.3 ; or CLR1 MBE ; TMn.bit3 ← 1 145 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-31. Timer/Event Counter Mode Register (Channel 0) Format Address FA0H 7 6 TM06 5 TM05 4 3 2 TM02 1 0 Symbol TM0 TM04 TM03 Count pulse (CP) selection bit When fX = 6.00 MHz TM06 0 0 1 1 1 1 TM05 0 0 0 0 1 1 TM04 0 1 0 1 0 1 TI0 rising edge TI0 falling edge fX/210 (5.86 kHz) fX/28 (23.4 kHz) fX/26 (93.8 kHz) fX/24 (375 kHz) Setting prohibited Count Pulse (CP) Other than above When fX = 4.19 MHz TM06 0 0 1 1 1 1 TM05 0 0 0 0 1 1 TM04 0 1 0 1 0 1 TI0 rising edge TI0 falling edge fX/210 (4.10 kHz) fX/28 (16.4 kHz) fX/26 (65.5 kHz) fX/24 (262 kHz) Setting prohibited Count Pulse (CP) Other than above Timer start indication bit TM03 When 1 is written into the bit, the counter and IRQT0 flag are cleared. If bit 2 is set to 1, count operation is started. Operation mode TM02 0 1 Count Operation Stop (retention of count contents) Count operation 146 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-32. Timer/Event Counter Mode Register (Channel 1) Format (1/2) Address FA8H 7 6 TM16 5 TM15 4 3 2 1 0 Symbol TM1 TM14 TM13 TM12 TM11 TM10 Count pulse (CP) select bit When fX = 6.00 MHz TM16 0 0 0 0 1 1 1 1 TM15 0 0 1 1 0 0 1 1 TM14 0 1 0 1 0 1 0 1 TI1 rising edge TI1 falling edge Overflow of timer/event counter channel 2 fX/25 (188 kHz) fX/212 (1.46 kHz) fX/210 (5.86 kHz) fX/28 (23.4 kHz) fX/26 (93.8 kHz) Count Pulse (CP) When fX = 4.19 MHz TM16 0 0 0 0 1 1 1 1 TM15 0 0 1 1 0 0 1 1 TM14 0 1 0 1 0 1 0 1 TI1 rising edge TI1 falling edge Overflow of timer/event counter channel 2 fX/25 (131 kHz) fX/212 (1.02 kHz) fX/210 (4.10 kHz) fX/28 (16.4 kHz) fX/26 (65.5 kHz) Count Pulse (CP) Timer start indication bit TM13 When 1 is written into the bit, the counter and IRQT1 flag are cleared. If bit 2 is set to 1, count operation is started. Operation mode TM12 0 1 Count Operation Stop (retention of count contents) Count operation 147 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-32. Timer/Event Counter Mode Register (Channel 1) Format (2/2) Operation mode select bit TM11 0 1 TM10 0 0 Mode 8-bit timer/event counter modeNote 16-bit timer/event counter mode Setting prohibited Other than the above Note When it is used in combination with the TM20 and TM21 (= 11) of the timer/event counter mode register (channel 2), it enters the carrier generator mode. Figure 5-33. Timer/Event Counter Mode Register (Channel 2) Format (1/2) Address F90H 7 6 TM26 5 TM25 4 3 2 1 0 Symbol TM2 TM24 TM23 TM22 TM21 TM20 Count pulse (CP) select bit When fX = 6.00 MHz TM26 0 0 0 0 1 1 1 1 TM25 0 0 1 1 0 0 1 1 TM24 0 1 0 1 0 1 0 1 TI2 rising edge TI2 falling edge fX/2 (3.00 MHz) fX (6.00 MHz) fX/210 (5.86 kHz) fX/28 (23.4 kHz) fX/26 (93.8 kHz) fX/24 (375 kHz) Count Pulse (CP) When fX = 4.19 MHz TM26 0 0 0 0 1 1 1 1 TM25 0 0 1 1 0 0 1 1 TM24 0 1 0 1 0 1 0 1 TI2 rising edge TI2 falling edge fX/2 (2.10 MHz) fX (4.19 MHz) fX/210 (4.10 kHz) fX/28 (16.4 kHz) fX/26 (65.5 kHz) fX/24 (262 kHz) Count Pulse (CP) 148 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-33. Timer/Event Counter Mode Register (Channel 2) Format (2/2) Timer start indication bit TM23 When 1 is written into the bit, the counter and IRQT2 flag are cleared. If bit 2 is set to 1, count operation is started. Operation mode TM22 0 1 Count Operation Stop (retention of count contents) Count operation Operation mode select bit TM21 0 0 1 1 TM20 0 1 0 1 Mode 8-bit timer/event counter mode PWM pulse generator mode 16-bit timer/event counter mode Carrier generator mode (2) Timer/event counter output enable flag (TOE0, TOE1) The timer/event counter output enable flag (TOE0, TOE1) controls the output enable/disable to the PTO0 and PTO1 pins in the timer out F/F (TOUT F/F) status. The timer out F/F flips by the match signal sent from the comparator. When bit 3 of the timer/event counter mode register (TM0, TM1) is set to “1”, the timer out F/F is cleared to “0”. TOE0, TOE1, and timer out F/F are cleared to “0” by a RESET signal generation. Figure 5-34. Timer/Event Counter Output Enable Flag Format Address FA2H FAAH TOE0 TOE1 Channel 0 Channel 1 Timer/event counter output enable flag (W) 0 1 Disabled. Enabled. 149 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (3) Timer/event counter control register (TC2) The timer/event counter control register (TC2) is an 8-bit register which controls the timer/event counter. Its format is shown in Figure 5-35. The timer/event counter control register (TC2) is set by an 8-bit/4-bit memory manipulation instruction. All the bits of the timer/event counter control register (TC2) are cleared to “0” by the internal reset signal generation. Figure 5-35. Timer/Event Counter Control Register Format Address F92H 7 TGCE 6 5 4 3 2 1 0 NRZ Symbol TC2 TOE2 REMC NRZB Gate control enable flag TGCE 0 Gate Control Disabled. (If bit 2 of the TM2 is set to “1”, the count operation is performed regardless of the sampling clock status.) Enabled. (If bit 2 of the TM2 is set to “1”, the count operation is performed when the sampling clock is high, and is stopped when the sampling clock is low) 1 Timer output enable flag TOE2 0 1 Timer Output Disabled (outputs the low level). Enabled. Remote control output control flag REMC 0 1 Remote Control Output Outputs the carrier pulse when NRZ = 1. Output a high-level signal when NRZ = 1. No return zero buffer flag NRZB No return zero data to be output next. Transferred to the NRZ when a timer/event counter (channel 1) interrupt is generated. No return zero flag NRZ 0 1 No Return Zero Data Outputs a low-level signal. Outputs the carrier pulse or high-level signal. 150 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.5.2 8-bit timer/event counter mode operation It is used as an 8-bit timer/event counter in this mode. It performs an 8-bit programmable interval timer and event counter operation. (1) Register setting The following four registers are used in the 8-bit timer/event counter mode. • Timer/event counter mode register (TMn) • Timer/event counter control register (TC2) Note • Timer/event counter count register (Tn) • Timer/event counter modulo register (TMODn) Note Channels 0 and 1 of the timer/event counter use the timer/event counter output enable flags (TOE0 and TOE1). (a) Timer/event counter mode register (TMn) When the 8-bit timer/event counter mode is used, TMn must be set as follows (For the format of the TMn, see Figures 5-31 to 5-33). The TMn is manipulated by an 8-bit manipulation instruction. Bit 3 is a timer start indication bit and can be manipulated bit-wise and is automatically cleared to “0” when the timer starts. The TMn is cleared to 00H when an internal reset signal is generated. 151 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-36. Timer/Event Counter Mode Register Setup (1/3) (a) In the case of timer/event counter (channel 0) Address FA0H 7 6 TM06 5 TM05 4 TM04 3 TM03 2 TM02 1 0 Symbol TM0 Count pulse (CP) selection bit TM06 0 0 1 1 1 1 TM05 TM04 0 0 0 0 1 1 0 1 0 1 0 1 TI0 rising edge TI0 falling edge fX/210 fX/28 fX/26 fX/24 Setting prohibited Count Pulse (CP) Other than above Timer start indication bit TM03 When “1” is written into the bit, the counter and IRQT0 flag are cleared. If bit 2 is set to “1”, count operation is started. Operation mode TM02 0 1 Count Operation Stop (retention of count contents) Count operation 152 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-36. Timer/Event Counter Mode Register Setup (2/3) (b) In the case of timer/event counter (channel 1) Address FA8H 7 6 TM16 5 TM15 4 TM14 3 TM13 2 TM12 1 TM11 0 TM10 Symbol TM1 Count pulse (CP) selection bit TM16 0 0 0 0 1 1 1 1 TM15 TM14 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 TI1 rising edge TI1 falling edge Timer/event counter channel 2 overflow fX/25 fX/212 fX/210 fX/28 fX/26 Count Pulse (CP) Timer start indication bit TM13 When “1” is written to the bit, the counter and IRQT1 flag are cleared. If bit 2 is set to “1”, count operation is started. Operation mode TM12 0 1 Count Operation Stop (retention of count contents) Count operation Operation mode selection bit TM11 0 TM10 0 Mode 8-bit timer/event counter mode 153 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-36. Timer/Event Counter Mode Register Setup (3/3) (c) In the case of timer/event counter (channel 2) Address F90H 7 6 TM26 5 TM25 4 TM24 3 TM23 2 TM22 1 TM21 0 TM20 Symbol TM2 Count pulse (CP) selection bit TM26 0 0 0 0 1 1 1 1 TM25 TM24 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 TI2 rising edge TI2 falling edge fX/2 fX fX/210 fX/28 fX/26 fX/24 Count Pulse (CP) Timer start indication bit TM23 When “1” is written to the bit, the counter and IRQT2 flag are cleared. If bit 2 is set to “1”, count operation is started. Operation mode TM22 0 1 Count Operation Stop (retention of count contents) Count operation Operation mode selection bit TM21 0 TM20 0 Mode 8-bit timer/event counter mode 154 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (b) Timer/event counter control register (TC2) Figure 5-37 shows the setting of the TC2 when it is used in an 8-bit timer/event counter mode (See Figure 5-35 Timer/Event Counter Control Register Format). The TC2 is manipulated by an 8-bit/4-bit manipulation instruction and bit manipulation instruction. The TC2 is cleared to 00H by an internal reset signal generation. The flag indicated by the full lines indicates a flag which is used in the 8-bit timer/event counter mode. The flag indicated by the broken lines must not be used in the 8-bit timer/event counter mode (Set 0). Figure 5-37. Timer/Event Counter Control Register Setup 7 TGCE 6 5 4 3 2 1 0 NRZ Symbol TC2 TOE2 REMC NRZB Gate control enable flag TGCE 0 Gate Control Disabled. (If bit 2 of the TM2 is set to “1”, the count operation is performed regardless of the status of the sampling clock.) Enabled. (If bit 2 of the TM2 is set to “1”, the count operation is performed when the sampling clock is high, and is stopped when the sampling clock is low.) 1 Timer output enable flag TOE2 0 1 Timer Output Disabled (outputs the low-level signal). Enabled. Figure 5-38. Timer/Event Counter Output Enable Flag Setup Address FA2H FAAH TOE0 TOE1 Channel 0 Channel 1 Timer/event counter output enable flag (W) 0 1 Disabled (outputs the low-level signal). Enabled. 155 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (2) Timer/event counter time setting [Time setting value] (count-up cycle) is found by dividing [modulo register content + 1] by [count pulse (CP) frequency] selected by setting the mode register. T (sec) = n+1 f CP = (n + 1) × (Resolution) T (sec) : Time value to be set in the timer (seconds) f CP (Hz) : Count pulse frequency (Hz) n : Modulo register content (n ≠ 0) Once the timer is set, an interrupt request signal (IRQTn) is generated at the intervals set in the timer. Table 5-7 lists the resolution and maximum allowable time setting (that is, time when FFH is set in the modulo register) for each count pulse to the timer/event counter. Table 5-7. Resolution and Maximum Allowable Time Setting (8-bit timer mode) (a) When timer/event counter (channel 0) Mode Register TM06 1 1 1 1 TM05 0 0 1 1 TM04 0 1 0 1 During 6.00-MHz Operation Resolution 171 µs 42.7 µ s 10.7 µ s 2.67 µ s Max. Time Setting 43.7 ms 10.9 ms 2.73 ms 683 µs During 4.19-MHz Operation Resolution 244 µ s 61.0 µs 15.3 µs 3.81 µs Max. Time Setting 62.5 ms 15.6 ms 3.91 ms 977 µs (b) When timer/event counter (channel 1) Mode Register TM16 0 1 1 1 1 TM15 1 0 0 1 1 TM14 1 0 1 0 1 During 6.00-MHz Operation Resolution 5.33 µ s 683 µs 171 µs 42.7 µ s 10.7 µ s Max. Time Setting 1.37 ms 175 ms 43.7 ms 10.9 ms 2.73 ms During 4.19-MHz Operation Resolution 7.63 µs 977 µ s 244 µ s 61.0 µs 15.3 µs Max. Time Setting 1.95 ms 250 ms 62.5 ms 15.6 ms 3.91 ms (c) When timer/event counter (channel 2) Mode Register TM26 0 0 1 1 1 1 TM25 1 1 0 0 1 1 TM24 0 1 0 1 0 1 During 6.00-MHz Operation Resolution 333 ns 167 ns 171 µs 42.7 µ s 10.7 µ s 2.67 µ s Max. Time Setting 85.3 µ s 42.7 µ s 43.7 ms 10.9 ms 2.73 ms 683 µs During 4.19-MHz Operation Resolution 477 ns 238 ns 244 µ s 61.0 µs 15.3 µs 3.81 µs Max. Time Setting 122 µs 61.0 µ s 62.5 ms 15.6 ms 3.91 ms 977 µs 156 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (3) Timer/event counter operation The timer/event counter operates as follows. In the operation, the gate control enable flag (TGCE) of the timer/ event counter control register (TC2) must be set to 0. Figure 5-39 shows the configuration of the timer/event counter. The count pulse (CP) is selected by setting the mode register (TMn) and is input to the count register (Tn). The Tn is compared with the modulo register (TMODn), and if they are equal, a match signal is generated and the interrupt request flag (IRQTn) is set. At the same time, the timer out flip-flop (TOUT F/F) flips. Figure 5-40 is a timing chart of the timer/event counter. The timer/event counter normally begins operation in the following procedure. Set a count in the TMODn. Set the operating mode, count pulse, and start indication in the TMn. Caution Set a value other than 00H in the modulo register (TMODn). When using the timer/event counter output pin (PTOn), set the alternate function pin P2n as follows. Clear the output latch of P2n. Set port 2 to the output mode. Make a status wherein the pull-up resistor is not incorporated in port 2 (When outputting PTO2, disable output of PCL). Set the timer/event counter output enable flag (TOEn) to 1. 157 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-39. Configuration of Timer/Event Counter INTTn (IRQTn set signal) TIn Modulo register (TMODn) Match Internal clock MPX CP Comparator TOUT F/F PTOn TOUT0 Count register (Tn) Clear To serial interfaceNote Note Only the channel 0 signal of the timer/event counter can be output to the serial interface. Figure 5-40. Count Operation Timing Count pulse(CP) Modulo register (TMODn) m Count register (Tn) 0 1 2 m–1 m 0 Match 1 2 m–1 m 0 Match 1 2 3 4 Reset TOUT F/F Timer start indication Remark m: Modulo register setup value n = 0 to 2 158 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (4) Event counter operation with gate control function (8-bit) The timer/event counter (channel 2) can be used as an event counter with a gate control function. Set the gate control enable flag (TGCE) of the timer/event counter control register to 1 when using this function. When timer/event counter channel 0 counts to the specified number, the gate signal is generated. When the gate signal (output of TOUT F/F of T0) is high, the count pulses of timer/event counter (channel 2) can be counted as shown in Figure 5-42 (for details, refer to (3) Timer/event counter operation). The count pulse (CP) is selected by setting the mode register (TM2), and the CP is input to the count register (T2) when the gate signal is high. Interrupt is generated at the rising edge and falling edge of the gate signal. Normally, the contents of the T2 are read out by an interrupt subroutine at the falling edge and the T2 is cleared for the subsequent count operation. Figure 5-42 shows the timing chart of the event counter operation. The event counter normally starts operation by the following procedure. Set the operation mode, count pulse, and counter clear indication in the TM2. Set the number of count in the TMOD0. Set the operation mode and start indication in the TM0. Caution A value other than 00H must be set in the modulo register (TMOD0, TMOD2). 159 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-41. Configuration of Event Count TI0 Modulo register (TMOD0) INTT0 (IRQT0 set signal) Internal clock MPX CP Comparator Match TOUT F/F PTO0 Count register (T0) Clear TI2 Modulo register (TMOD2) INTT2 (IRQT2 set signal) Match Internal clock MPX Comparator TOUT F/F PTO2 Count register (T2) CP Clear 160 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-42. Event Count Operation Timing Count pulse (CP) Modulo register (TMOD0) m Count register (T0) 0 1 2 m–1 m 0 Match 1 2 m–1 m 0 Match 1 2 3 4 Gate signal (TOUT F/F) Reset IRQT0 set Count disable Count enable IRQT0 set Count disable Event input (TI2) Count register (T2) 0 1 2 m–2 m–1 0 Counter clear indication Timer start indication Remark m: Modulo register setup value 161 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (5) 8-bit timer/event counter mode application (a) Use as an interval timer which causes an interrupt to occur at 50 ms intervals (@fX = 4.19 MHz). • Set the high-order four bits of the mode register (TMn) to 0100B to select the longest setup time 62.5 ms. • Set the low-order four bits of the TMn to 1100B. • The value set in the modulo register (TMODn) is as follows: 50 ms 244 µ s = 205, 205 – 1 = CCH SEL MOV MOV MOV MOV EI EI IETn MB15 XA, #0CCH TMODn, XA XA, #01001100B TMn, XA ; Set mode and start timer ; Enable interrupt ; Enable timer interrupt ; Set modulo ; or CLR1 MBE Remark In this example, the TIn pin can be used as an input pin. (b) Generate an interrupt when the number of pulses input from the TIn pin reaches 100 (The pulses are active high). • Set the high-order four bits of the mode register (TMn) to 0000 to select rising edge. • Set the low-order four bits of the TMn to 1100B. • The value set in the modulo register (TMODn) is 99 = 100 – 1. SEL MOV MOV MOV MOV EI EI IETn ; Enable INTTn MB15 XA, #100 – 1 TMODn, XA XA, #00001100B TMn, XA ; Set mode, start count ; Set modulo ; or CLR1 MBE 162 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (c) Application used as an event counter with sampling time (15 ms) and hold time (2 ms) after 121 µ s count disabled time (@fX = 4.19 MHz). Set the timer/event counter (channel 0) as follows. • Set the high-order 4 bits of the mode register (TM0) to 0101B to select the longest time 15.6 ms. • Set the low-order 4 bits of the TM0 to 1100B to select the 8-bit timer/event counter mode and count operation and indicate timer start. • Set the modulo register (TMOD0) to 01H (121 µ s) initially and then 20H (15.03 ms) and F5H (2.02 ms). Set the timer/event counter (channel 2) as follows. • Set the high-order 4 bits of the TM2 to 0000B in order to select the TI2 rising edge. • Set the low-order 4 bits of the TM2 to 1100B in order to select the 8-bit timer/event counter mode and count operation and indicate counter clear. • Set the TGCE to “1” and enable gate control. • Set the TMOD2 to the greatest value FFH. • Designate the memory MEM which stores the contents of the count register (T2). MAIN: SEL SET1 MOV MOV MOV MOV MOV MOV MOV EI EI IET0 MB15 TGCE XA, #00001100B TM2, XA XA, #001H TMOD0, XA XA, #01011100B TM0, XA B, #00H ; Sets the mode and indicates timer start. ; Initialization ; Enables interrupt. ; Enables timer (channel 0) interrupt. ; Sets the modulo (during the initial counting disabled time). ; Sets the mode and clears the counter. ; or CLR1 MBE ; Enables gate control. 163 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION ; INCS SKE BR HOLD: MOV MOV MOV MOV SET1 MOV BR SAMP: END : MOV MOV RETI B B, #02H SAMP XA, #020H TMOD0, XA XA, T2 MEM, XA TM2. 3 B, #00H END XA, #0F5H TMOD0, XA ; Rewrite modulo (15 ms) ; Read the counter ; Clear the counter ; Rewrite modulo (2 ms) Remark In this example, TI0 and TI1 can be used as input pins. When the sampling clock goes to high, the count operation starts and, at the same time, the initial interrupt is generated. The TMOD0 is updated to F5H and then the count operation continues for 15 ms. When sampling clock goes to low, the count operation stops and, at the same time, the second interrupt is generated. The TMOD0 is updated to 20H and then the count operation stops for 2 ms. The contents of the T2 are read out and it is cleared for the next count operation. Then, repeat the above operation. 164 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.5.3 PWM pulse generator mode (PWM mode) operation It performs as an 8-bit PWM pulse generator in this mode. (1) Register setting The following five registers are used in the PWM mode. • Timer/event counter mode register (TM2) • Timer/event counter control register (TC2) • Timer/event counter count register (T2) • Timer/event counter high-level period setting modulo register (TMOD2H) • Timer/event counter modulo register (TMOD2) (a) Timer/event counter mode register (TM2) When using the PWM mode, set the TM2 as shown in Figure 5-43. For the format of the TM2, see Figure 5-33 Timer/Event Counter Mode Register (Channel 2) Format. The TM2 is manipulated by an 8-bit manipulation instruction. Bit 3 is a timer start indication bit. It can be manipulated bit-wise and is automatically cleared to 0 when the timer starts. The TM2 is cleared to 00H when an internal reset signal is generated. 165 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-43. Timer/Event Counter Mode Register Setup Address F90H 7 6 TM26 5 TM25 4 TM24 3 TM23 2 TM22 1 TM21 0 TM20 Symbol TM2 Count pulse (CP) selection bit TM26 0 0 0 0 1 1 1 1 TM25 TM24 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 TI2 rising edge TI2 falling edge fX/2 fX fX/210 fX/28 fX/26 fX/24 Count Pulse (CP) Timer start indication bit TM23 When “1” is written to the bit, the counter and IRQT2 flag are cleared. If bit 2 is set to “1”, count operation is started. Operation mode TM22 0 1 Count Operation Stop (retention of count contents) Count operation Operation mode selection bit TM21 0 TM20 1 PWM pulse generator mode Mode 166 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (b) Timer/event counter control register (TC2) When using the PWM mode, set the TC2 as shown in Figure 5-44 (For the format of TC2, see Figure 535 Timer/Event Counter Control Register Format). The TC2 is manipulated by an 8-bit/4-bit manipulation instruction and bit manipulation instruction. The TC2 is cleared to 00H by an internal reset signal generation. The flag indicated by the full lines is used in the PWM mode. The flag indicated by the broken lines must not be used for the PWM mode (Set 0). Figure 5-44. Timer/Event Counter Control Register Setup 7 TGCE 6 5 4 3 2 1 0 NRZ Symbol TC2 TOE2 REMC NRZB Timer output enable flag TOE2 0 1 Timer Output Disabled (output the low-level signal). Enabled. 167 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (2) PWM pulse generator operation The PWM pulse generator operates as follows. Figure 5-45 shows its configuration. When the mode register (TM2) is set, the count pulse (CP) is selected and input to the count register (T2). The contents of the T2 are compared with those of the high-level period setting modulo register (TMOD2H), and if they are equal, a match signal is generated and the timer out flip-flop (TOUT F/F) flips. The contents of the T2 are compared with those of the modulo register (TMOD2), and if they are equal, a match signal is generated and an interrupt request flag (IRQT2) is set. At the same time, the TOUT F/F flips. The above operations and repeat alternatively. Figure 5-46 shows the timing chart of the PWM pulse generator. The PWM pulse generator normally starts operation in the following procedure. Set the number of count in the TMOD2H. Set the number of low-level count in the TMOD2. Set the operating mode, count pulse, and start indication in the TM2. Caution Set values other than 00H in the modulo register (TMOD2) and high-level period setting modulo register (TMOD2H). When using the timer/event counter output pin (PTO2), set the alternate function pins P22 and PCL as follows. Clear the output latch of P22. Set port 2 to output mode. Make a status wherein port 2’s on-chip pull-up resistor is not incorporated, and disable the PCL output. Set the timer/event counter output enable flag (TOE2) to 1. 168 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-45. Configuration of PWM Pulse Generator High-level period setting modulo register (TMOD2H) Modulo register (TMOD2) INTT2 (IRQT2 set signal) TI2 MPX Match Internal clock MPX CP Comparator TOUT F/F PTO2 Count register (T2) Clear Figure 5-46. PWM Pulse Generator Operation Timing Count pulse (CP) High-level period setting modulo register (TMOD2H) m Modulo register (TMOD2) n Count register (T2) 0 1 2 m–1 m 0 Match 1 2 n–1 n 0 Match 1 2 3 4 TOUT F/F Set IRQT2 set Timer start indication Remark m : Setup value of high-level period setting modulo register n : Modulo register setup value 169 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (3) PWM mode application The pulses (frequency is 38.0 kHz (cycle is 26.3 µ s) and duty ratio is 1/3) are output to the PTO2 pin (@fX = 4.19 MHz). • Set the high-order 4 bits of the mode register (TM2) to 0011B and select the longest setup time 61.1 µ s. • Set the low-order 4-bits of the TM2 to 1101B and select the PWM mode and count operation and indicate timer start. • Set the timer output enable flag (TOE2) to “1” and enable the timer output. • The high-level period setting modulo register (TMOD2H) is set as follows. 1 3 × 26.3 µ s 239 ns – 1 = 36.7 – 1 ≅ 36 = 24H • The modulo register (TMOD2) is set as follows. 2 3 × 26.3 µ s 239 ns – 1 = 73.4 – 1 ≅ 72 = 48H SEL SET1 MOV MOV MOV MOV MOV MOV MB15 TOE2 XA, #024H TMOD2H, XA XA, #48H TMOD2, XA XA, #00111101B TM2, XA ; Sets the mode and timer start. ; Sets the modulo (low-level period). ; Sets the modulo (high-level period). ; or CLR1 MBE ; Enables timer output. Remark In this example, TI0, TI1, and TI2 can be used as input pins. 170 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.5.4 16-bit timer/event counter mode operation Used as a 16-bit timer/event counter in this mode. It performs 16-bit programmable interval timer and event counter. When it is used in the 16-bit timer/event counter mode, the channel 1 and channel 2 of the timer/event counter are used in combination. (1) Register setting The following seven registers are used in the 16-bit timer/event counter mode. • Timer/event counter mode registers (TM1, TM2) • Timer/event counter control register (TC2) Note • Timer/event counter count registers (T1, T2) • Timer/event counter modulo registers (TMOD1, TMOD2) Note The timer/event counter (channel 1) uses the timer/event counter output enable flag (TOE1). (a) Timer/event counter mode registers (TM1, TM2) When using the 16-bit timer/event counter mode, set the TM1 and TM2 as shown in Figure 5-47. For the formats of the TM1 and TM2, see Figure 5-32 Timer/Event Counter Mode Register (Channel 1) Format and Figure 5-33 Timer/Event Counter Mode Register (Channel 2) Format, respectively. The TM1 and TM2 are manipulated by 8-bit manipulation instructions. Bit 3 is a timer start indication bit and can be manipulated bit-wise and is automatically cleared to 0 when the timer starts. The TM1 and TM2 are cleared to 00H by an internal reset signal generation. The flag indicated by the full lines expresses a bit used in the 16-bit timer/event counter mode. The flag indicated by the broken lines must not be used in the 16-bit timer/event counter mode (Set 0). 171 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-47. Timer/Event Counter Mode Register Setup Address FA8H 7 6 TM16 5 TM15 4 TM14 3 TM13 2 TM12 1 TM11 0 TM10 Symbol TM1 F90H TM26 TM25 TM24 TM23 TM22 TM21 TM20 TM2 Count pulse (CP) selection bit (n = 1, 2) TMn6 0 0 0 0 1 1 1 1 TMn5 TMn4 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 TI1 rising edge TI1 falling edge Count register (T2) overflow fX/25 fX/2 12 TM1 TI2 rising edge TI2 falling edge fX/2 fX fX/210 fX/28 fX/26 fX/24 TM2 fX/210 fX/28 fX/26 Timer start indication bit TM23 When “1” is written to the bit, the counter and IRQTn flag are cleared. If bit 2 is set to “1”, count operation is started. Operation mode TM22 0 1 Count Operation Stop (retention of count contents) Count operation Operation mode selection bit TM21 1 TM20 0 TM11 1 TM10 0 Mode 16-bit timer/event counter mode 172 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (b) Timer/event counter control register (TC2) When using the 16-bit timer/event counter mode, set the TC2 as shown in Figure 5-48. For the format of the TC2, see Figure 5-35 Timer/Event Counter Control Register Format. The TC2 is manipulated by an 8-bit/4-bit manipulation instruction and bit manipulation instruction. The TC2 is cleared to 00H by an internal reset signal generation. The flag indicated by the full lines is a flag used in the 16-bit timer/event counter mode. The flag indicated by the broken lines must not be used in the 16-bit timer/event counter mode (Set 0). Figure 5-48. Timer/Event Counter Control Register Setup 7 TGCE 6 5 4 3 2 1 0 NRZ Symbol TC2 TOE2 REMC NRZB Gate control enable flag TGCE 0 Gate Control Disabled. (If the bit 2 of the TM2 is set to “1”, the count opration is performed regardless of the status of sampling clock.) Enabled. (If the bit 2 of the TM2 is set to “1”, the count opration is performed when the sampling clock is high and is stopped when the sampling clock is low.) 1 Timer output enable flag TOE2 0 1 Timer Output Disabled (outputs the low level signal). Enabled. 173 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (2) Timer/event counter time setting [Time setting value] (count-up cycle) is found by dividing [modulo register content + 1] by [count pulse (CP) frequency] selected by setting the mode register. T (sec) = n+1 f CP = (n + 1) × (Resolution) T (sec) : Time value to be set in the timer (seconds) f CP (Hz) : Count pulse frequency (Hz) n : Modulo register content (n ≠ 0) Once the timer is set, an interrupt request signal (IRQT2) is generated at the intervals set in the timer. Table 5-8 lists the resolution and maximum allowable time setting (that is, time when FFH is set in the modulo register) for each count pulse to the timer/event counter. Table 5-8. Resolution and Maximum Allowable Time Setting (16-bit timer mode) (a) When timer/event counter (channel 1) Mode Register TM16 0 1 1 1 1 TM15 1 0 0 1 1 TM14 1 0 1 0 1 During 6.00-MHz Operation Resolution 5.33 µ s 683 µs 171 µs 42.7 µ s 10.7 µ s Max. Time Setting 350 ms 44.7 s 11.2 s 2.80 s 699 ms During 4.19-MHz Operation Resolution 7.63 µs 977 µ s 244 µ s 61.0 µs 15.3 µs Max. Time Setting 500 ms 64.0 s 16.0 s 4.00 s 1.00 s (b) When timer/event counter (channel 2) Mode Register TM26 0 0 1 1 1 1 TM25 1 1 0 0 1 1 TM24 0 1 0 1 0 1 During 6.00-MHz Operation Resolution 333 ns 167 ns 171 µs 42.7 µ s 10.7 µ s 2.67 µ s Max. Time Setting 21.8 ms 10.9 ms 11.2 s 2.80 s 699 ms 175 ms During 4.19-MHz Operation Resolution 477 ns 238 ns 244 µ s 61.0 µs 15.3 µs 3.81 µs Max. Time Setting 31.3 ms 15.6 ms 16.0 s 4.00 s 1.00 s 250 ms 174 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (3) Timer/event counter operation The timer/event counter operates as follows. In this operation mode, set the gate control enable flag (TGCE) of the timer/event counter control register (TC2) to 0. Figure 5-49 shows the configuration of the timer/event counter. The count pulse (CP) is selected by setting the mode registers (TM1 and TM2), and is input to the count register (T2). The overflow of the T2 is input to the count register (T1). The contents of the T1 and those of the modulo register (TMOD1) are compared, and if they are equal, a match signal is generated. The contents of the T2 are compared with those of the modulo register (TMOD2), and if they are equal, a match signal is generated. If the match signals of and above are the same, an interrupt request flag (IRQT2) is set. At the same time, the timer out flip-flop (TOUT F/F) flips. Figure 5-50 shows the timing chart of the timer/event counter operation. The timer/event counter normally starts the operation in the following procedure. Set the high-order 8-bits of the count expressed by a 16-bit width in the TMOD1. Set the low-order 8-bits of the count expressed by a 16-bit width in the TMOD2. Set the operating mode and count pulse in the TM1. Set the operating mode, count pulse, and start indication in the TM2. Caution Set a value other than 00H to the modulo register (TMOD2). When using the timer/event counter output pin (PTO2), set the alternate function pins P22 and PCL as follows. Clear the output latch of P22. Set port 2 to the output mode. Make a status wherein the port 2’s on-chip pull-up resistor is not incorporated, and disable the PCL output. Set the timer/event counter output enable flag (TOE2) to 1. 175 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-49. Timer/Event Counter Operation Configuration TI1 Modulo register (TMOD1) MPX Internal clock Comparator Match CP Count register (T1) Clear TI2 Modulo register (TMOD2) INTT2 (IRQT2 set signal) Internal clock MPX CP Comparator Match TOUT F/F PTO2 Count register (T2) Clear Figure 5-50. Count Operation Timing Count pulse (CP) Modulo register (TMOD2) n Count register (T2) 0 1 2 n 255 0 1 2 n–1 n 0 1 2 Modulo register (TMOD1) m Match Count register (T1) 0 m–1 m Match 0 TOUT F/F Set Timer start indication Remark m : Modulo register (TMOD1) setup value n : Modulo register (TMOD2) setup value 176 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (4) Event counter operation with gate control function (16 bits) The timer/event counter (channel 1) and timer/event counter (channel 2) can be used as an event counter with gate control function. Set the gate control enable flag (TGCE) of the timer/event counter control register to 1 when using this function. When timer/event counter (channel 0) counts to the specified number, the gate signal is generated. When the gate signal (output of TOUT F/F of T0) is high, the count pulses of timer/event counters (channel 1 and channel 2) can be counted as shown in Figure 5-52 (for details, refer to (3) Timer/event counter operation). When the mode registers (TM1 and TM2) are set, the count pulse (CP) is selected. When the gate signal is high, the CP is input to the count register (T2). The overflow of the T2 is input to the count register (T1). Interrupts are generated at the rising edge and falling edge of the gate signal. Normally, the contents of the T1 and T2 are read out by an interrupt subroutine of the falling edge and they are then cleared for the next count operation. Figure 5-52 shows the timing chart of the event counter operation. The event counter normally starts operation in the following procedure. Set the operation mode and count pulse in the TM1. Set the operation mode, count pulse, and counter clear indication in the TM2. Set the number of count in the TMOD0. Set the operation mode, count pulse, and start indication in the TM0. Cautions 1. Set a value other than 00H in the modulo registers (TMOD0, TMOD1, TMOD2). 2. Do not set 1 to the timer/event counter interrupt enable flag (IET1). 177 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-51. Event Count Operation Configuration TI0 Modulo register (TMOD0) INTT0 (IRQT0 set signal) Match MPX Internal clock Comparator TOUT F/F PTO0 CP Count register (T0) Clear TI2 Modulo register (TMOD2) INTT2 (IRQT2 set signal) Match MPX Internal clock Comparator TOUT F/F PTO2 Count register (T2) CP Clear TI1 Modulo register (TMOD1) MPX Internal clock Comparator Match CP Count register (T1) Clear 178 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-52. Event Count Operation Timing Count pulse (CP) Modulo register (TMOD0) n Count register (T0) 0 1 2 n–1 n 0 Match 1 2 n–1 n 0 Match 1 2 3 4 Gate signal (TOUT F/F) Reset IRQT0 set Count disable Count enable IRQT0 set Count disable Event input (TI2) Count register (T1: high-order) 0 i Count register (T2: Iow-order) 0 1 2 j–2 j–1 j Counter clear indication Timer start indication Remark i : Count register (T1: high-order) setup value j : Count register (T2: low-order) setup value n : Modulo register (TMOD0) setup value 179 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (5) 16-bit timer/event counter mode application (a) Application used as an interval timer generating interrupts every 5 seconds (@ fX = 4.19 MHz). • Set the high-order 4-bits of the mode register (TM1) to 0010B and select the overflow of the count register (T2). • Set the high-order 4-bits of the TM2 to 0100B and select the longest setup time 16.0 sec. • Set the low-order 4-bits of the TM1 to 0010B and select the 16-bit timer/event counter mode. • Set the low-order 4-bits of the TM2 to 1110B and select the 16-bit timer/event counter mode and count operation and indicate timer start. • Set the modulo registers (TMOD1, TMOD2) as follows. 5 sec 244 µ s = 20491.8 – 1 = 500BH SEL MOV MOV MOV MOV MOV MOV MOV MOV DI EI EI IET2 MB15 XA, #050H TMOD1, XA XA, #00BH TMOD2, XA XA, #00100010B TM1, XA XA, #01001110B TM2, XA IET1 ; Sets the mode and starts the timer. ; Disables the timer (channel 1) interrupts. ; Enables the interrupts. ; Enables the timer (channel 2) interrupts. ; Sets the mode. ; Sets the modulo (for low-order 8 bits). ; Sets the modulo (for high-order 8 bits). ; or CLR1 MBE Remark In this example, TI0, TI1, and TI2 can be used as the input pins. 180 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (b) When the pulse (input from the TI2 pin) count reaches 1000, the interrupts are generated (The pulses are active high). • Set the high-order 4 bits of the mode register (TM1) to 0010B and select the overflow of the count register (T2). • Set the high-order 4 bits of the TM2 to 0000B and select the rising edge of the TI2 input. • Set the low-order 4 bits of the TM1 to 0010B and select the 16-bit timer/event counter mode. • Set the low-order 4 bits of the TM2 to 1110B and select the 16-bit timer/event counter mode and count operation and indicate timer start. • Set the modulo registers (TMOD1, TMOD2) to 1000 – 1 = 999 = 03E7H. Set the TMOD1 to 03H. Set the TMOD2 to E7H. SEL MOV MOV MOV MOV MOV MOV MOV MOV DI EI EI IET2 ; Enables the timer (channel 2) interrupts. MB15 XA, #003H TMOD1, XA XA, #0E7H TMOD2, XA XA, #00100010B TM1, XA XA, #00001110B TM2, XA IET1 ; Sets the mode and starts the timer. ; Disables the timer (channel 1) interrupts. ; Sets the mode. ; Sets the modulo (for low-order 8 bits). ; Sets the modulo (for high-order 8 bits). ; or CLR1 MBE Remark In this example, TI1 and TI2 can be used as the input pins. (c) Following the 121 µ s count disabled period, it can be used as an event counter with the sampling time (15 ms) and hold time (2 ms) (@ fX = 4.19 MHz). The timer/event counter (channel 0) can be set as follows. • Set the high-order 4 bits of the mode register (TM0) to 0101B and select the longest setup time 15.6 ms. • Set the low-order 4 bits of the TM0 to 1100B and select the 8-bit timer/event counter mode and count operation and indicate timer start. • Set the modulo register (TMOD0) to 01H (121 µ s) initially and then 20H (15.03 ms) and F5H (2.02 ms). 181 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION The timer/event counter (channel 1) is set as follows: • Set the high-order 4 bits of the TM1 to 0010B and select the overflow of the count register (T2). • Set the low-order 4 bits of the TM0 to 0010B and select the 16-bit timer/event counter mode and count operation and indicate timer start. • Set the TMOD1 to the longest setup value FFH. • Designate the memory MEM1 that stores the contents of the count register (T1). The timer/event counter (channel 2) is set as follows. • Set the high-order 4 bits of the TM2 to 0000B and select the rising edge of the TI2. • Set the low-order 4 bits of the TM2 to 1110B and select the 16-bit timer/event counter mode and count operation and indicate counter clear. • Set the TGCE to “1” and enable the gate control. • Set the TMOD2 to the longest setup value FFH. • Designate the memory MEM2 that stores the contents of the count register (T2). MAIN: SEL SET1 MOV MOV MOV MOV MOV MOV MOV MOV MOV EI EI IET0 MB15 TGCE XA, #00100010B TM1, XA XA, #00001110B TM2, XA XA, #001H TMOD0, XA XA, #01011100B TM0, XA B, #00H ; Sets the mode and indicates timer start. ; Initialization ; Enables the interrupts. ; Enables the timer (channel 0) interrupts. ; Sets the modulo (the initial count disabled time). ; Sets the mode and clears the counter. ; Sets the mode. ; or CLR1 MBE ; Enables the gate control. 182 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION ; INCS SKE BR HOLD: MOV MOV MOV MOV MOV MOV SET1 MOV BR SAMP: END: Remark MOV MOV RETI In this example, the TI0 and TI1 can be used as the input pins. B B, #02H SAMP XA, #020H TMOD0, XA XA, T1 MEM1, XA XA, T2 MEM2, XA TM2.3 B, #00H END XA, #0F5H TMOD0, XA ; Updates the modulo (15 ms). ; Reads the counter (T2). ; Clears the counter. ; Reads the counter (T1). ; Updates the modulo (2 ms). When the sampling clock goes high, the count operation starts and, at the same time, the initial interrupt is generated. The TMOD0 is updated to F5H and then the count operation continues for 15 ms. When the sampling clock goes low, the count operation stops and, at the same time, the second interrupt is generated. The TMOD0 is updated to 20H and then the count operation is disabled for 2 ms. The contents of the T1 and T2 are read out and then they are cleared for the next count operation. Then, the above operation is repeated. 183 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.5.5 Carrier generator mode (CG mode) operation It is used as an 8-bit carrier generator in this mode. When using this mode, it is used in combination with channel 1 and channel 2 of the timer/event counter. The timer/event counter (channel 1) generates remote control signals. The timer/event counter (channel 2) generates carrier clocks. (1) Register setting In the CG mode, the following eight registers are used. • Timer/event counter mode registers (TM1, TM2) • Timer/event counter control register (TC2) Note • Timer/event counter count registers (T1, T2) • Timer/event counter modulo registers (TMOD1, TMOD2) • Timer/event counter high-level period setting modulo register (TMOD2H) Note The channel 1 of the timer/event counter uses the timer/event counter output enable flag (TOE1). (a) Timer/event counter mode register (TM1, TM2) When using the CG mode, set the TM1 and TM2 as shown in Figure 5-53 (For the format of the TM1, see Figure 5-32 Timer/Event Counter Mode Register (Channel 1) Format. For the format of TM2, see Figure 5-33 Timer/Event Counter Mode Register (Channel 2) Format). The TM1 and TM2 are manipulated by the 8-bit manipulation instructions. Bit 3 is a timer start indication bit and can be manipulated bit-wise and is automatically cleared to 0 when the timer starts operation. The TM1 and TM2 are cleared to 00H when the internal reset signals are generated. 184 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-53. Timer/Event Counter Mode Register Setup (n = 1, 2) Address FA8H 7 6 TM16 5 TM15 4 TM14 3 TM13 2 TM12 1 TM11 0 TM10 Symbol TM1 F90H TM26 TM25 TM24 TM23 TM22 TM21 TM20 TM2 Count pulse (CP) selection bit TMn6 0 0 0 0 1 1 1 1 TMn5 TMn4 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 TM1 TI1 rising edge TI1 falling edge Carrier clock input fX/25 fX/2 12 TM2 TI2 rising edge TI2 falling edge fX/2 fX fX/210 fX/28 fX/26 fX/24 fX/210 fX/28 fX/26 Timer start indication bit TMn3 When “1” is written into the bit, the counter and IRQTn flag are cleared. If bit 2 is set to “1”, count operation is started. Operation mode TMn2 0 1 Count Operation Stop (retention of count contents) Count operation Opetation mode selection bit TM21 1 TM20 1 TM11 0 TM10 0 Mode Carrier generator mode 185 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (b) Timer/event counter control register (TC2) When using the CG mode, set the timer output enable flag (TOE1) and TC2 as shown in Figures 5-54 and 5-55 (For the format of the TC2, see Figure 5-35 Timer/Event Counter Control Register Format) . The TOE1 is manipulated by a bit manipulation instruction. The TC2 is manipulated by an 8-bit/4-bit manipulation instruction and bit manipulation instruction. The TOE1 and TC2 are cleared to 00H by the internal reset signal generation. The flag indicated by the full lines expresses a flag used in the CG mode. The flag indicated by the broken lines must not be used in the CG mode (Set “0”). Figure 5-54. Timer/Event Counter Output Enable Flag Setup Address FAAH TOE1 Timer/event counter output enable flag (W) 0 1 Disabled. Enabled. Figure 5-55. Timer/Event Counter Control Register Setup 7 TGCE 6 5 4 3 2 1 0 NRZ Symbol TC2 TOE2 REMC NRZB Remote control output control flag REMC 0 1 Remote Control Output Outputs the carrier pulse when NRZ = 1. Outputs the high-level signal when NRZ = 1. No return zero buffer flag NRZB No return zero data to be output next. Transferred to the NRZ when a timer/event counter (channel 1) interrupt is generated. No return zero flag NRZ 0 1 No Return Zero Data Outputs the low-level signal. Outputs the carrier pulse or high-level signal. 186 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (2) Carrier generator operation The carrier generator operates as follows. Figure 5-56 shows its configuration. (a) Timer/event counter (channel 1) operation The timer/event counter (channel 1) determines the reloading interval from the no return zero buffer flag (NRZB) to the no return zero flag (NRZ). The timer/event counter (channel 1) operates as follows (For details, see 5.5.2 8-bit timer/event counter mode operation). When the mode register (TM1) is set, the count pulse (CP) is set and is input to the count register (T1). The contents of the T1 and those of the modulo register (TMOD1) are compared, and if they are equal, a match signal is generated and the interrupt request flag (IRQT1) is set. At the same time, the timer out flip-flop (TOUT F/F) flips. (b) Timer/event counter (channel 2) operation The timer/event counter (channel 2) generates the carrier clock and outputs the carrier signal according to the no return zero data. The timer/event counter (channel 2) operates as follows (For details, see 5.5.3 PWM pulse generator mode (PWM mode) operation). When the mode register (TM2) is set, the count pulse (CP) is selected and is input to the count register (T2). The contents of the T2 and those of the high-level period setting modulo register (TMOD2H) are compared, and if they are equal, a match signal is generated and the timer out flip/flop (TOUT F/ F) flips. The contents of the T2 and those of the modulo register (TMOD2) are compared, and if they are equal, a match signal is generated and the interrupt request flag (IRQT2) is set. At the same time, the TOUT F/F flips. Repeat the above operations and . The no return zero data is reloaded from the NRZB to the NRZ when an interrupt is generated in the timer/event counter (channel 1). When the remote control output control flag (REMC) is set and NRZ = 1, the carrier clock signal or high-level signal is output. When NRZ = 0, a low-level signal is output. Figure 5-57 shows the timing chart of the carrier generator. 187 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION The carrier generator normally operates in the following procedure. Set the number of count of the carrier clock’s high-level signals in the TMOD2H. Set the number of count of the carrier clock’s low-level signals in the TMOD2. Set the style of the output waveform in the REMC. Set the operation mode, count pulse, and start indication in the TM2. Set the number of count in the TMOD1. Set the operation mode, count pulse, and start indication in the TM1. Set the next no return zero data in the NRZB at any time before an interrupt is generated in the timer/ event counter (channel 1). Caution Set the values other than 00H in the modulo registers (TMOD1, TMOD2, TMOD2H). When using the timer/event counter output pin (PTO1), set the alternate function pin P21 as follows. Clear the output latch of P21. Set port 2 to the output mode. Make a status wherein the on-chip pull-up resistor in port 2 is not incorporated. Set the timer/event counter output enable flag (TOE1) to 1. 188 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-56. Carrier Generator Operation Configuration TI1 Modulo register (TMOD1) INTT1 (IRQT1 set signal) Match MPX Internal clock Comparator TOUT F/F PTO1 CP Count register (T1) Clear Carrier clock NRZB Reload High-level period setting modulo register (TMOD2H) NRZ PTO2 Modulo register (TMOD2) TI2 MPX INTT2 (IRQT2 set signal) Match TOUT F/F Internal clock MPX CP Comparator Count register (T2) Clear 189 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-57. Carrier Generator Operation Timing Count pulse (CP) High-level period setting modulo register (TMOD2H) Modulo register (TMOD2) i k Count register (T2) k 0 1 2 i–1 i 0 1 2 k–1 k 0 1 2 3 4 Carrier clock Modulo register (TMOD1) n Count register (T1) n 0 1 2 n 0 1 2 n 0 1 2 n 0 1 2 n 0 1 Interrupt generation (channel1) IRQT1 set No return zero buffer flag (NRZB) 1 Reload No return zero flag (NRZ) 0 1 0 Reload 0 IRQT1 set 1 Reload 1 IRQT1 set 1 Reload 1 0 IRQT1 set 0 IRQT1 set PTO2 pin Remark i : Setup value of high-level period setting modulo register (TMOD2H) k : Modulo register (TMOD2) setup value n : Modulo register (TMOD1) setup value 190 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Remark When the PTO2 pin is high (the no return zero flag (NRZ) is “0” and the carrier clock signal is high) and a timer/event counter (channel 1) interrupt is generated, the PTO2 pin output does not change according to the updated contents of NRZ until the carrier clock signal goes high. When the PTO2 pin is high (the NRZ is “1” and the carrier clock is high) and a timer/event counter (channel 1) interrupt is generated, the PTO2 pin output does not change according to the updated contents of NRZ until the carrier clock signal goes low. This is to keep a certain high-level pulse width of the output carrier (see the figure below). No return zero flag (NRZ) Carrier clock PTO2 pin Even if the NRZ is set to “1”, the PTO2 pin output does not go high until the next carrier clock pulse goes high. Even if the NRZ is set to “0”, the PTO2 pin output does not go low until the next carrier clock pulse goes low. (3) CG mode applications It can be used as a carrier generator for remote control transmission. (a) A carrier clock signal (frequency is 38.0 kHz (cycle: 26.3 µ s) and duty ratio is 1/3) is generated (@ fX = 4.19 MHz). • Set the high-order 4-bits of the mode register (TM2) to 0011B and select the longest setup time 61.1 µ s. • Set the low-order 4-bits of the TM2 to 1111B and select the CG mode and count operation and indicate timer start. • Set the timer output enable flag (TOE2) to “1” and enable timer output. • Set the high-level period setting modulo register (TMOD2H) to the following value. 1 3 × 26.3 µs 239 ns – 1 = 36.7 – 1 ≅ 36 = 24H • Set the modulo register (TMOD2) to the following value. 2 3 × 26.3 µs 239 ns – 1 = 73.4 – 1 ≅ 72 = 48H SEL MOV MOV MOV MOV MOV MOV MB15 XA, #024H TMOD2H, XA XA, #48H TMOD2, XA XA, #00111111B TM2, XA ; Sets the mode and starts the timer. ; Sets the modulo (low-level period). ; Sets the modulo (high-level period). ; or CLR1 MBE 191 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (b) A reader code (carrier clock output period is 9 ms and low-level output period is 4.5 ms) is output. See the illustration below (@ fX = 4.19 MHz). • Set the high-order 4 bits of the mode register (TM1) to 0110B and select the longest setup time 15.6 ms. • Set the low-order 4 bits of the TM1 to 1100B and select the 8-bit timer/event counter mode and count operation and indicate timer start. • Set the modulo register (TMOD1) to the following initial value. 9 ms 61 µ s – 1 = 147.5 – 1 ≅ 146 = 92H • Set the TMOD1 as follows when update it. 4.5 ms 61 µ s – 1 = 73.7 – 1 ≅ 73 = 49H • Set the high-order 4 bits of the TC2 to 0000B and disable the gate control. • Set the low-order 4 bits of the TC2 to 0000B and output the carrier clock signal when no return zero data is “1” and set the next no return zero data to “0”. SEL MOV MOV MOV MOV SET1 MOV MOV EI EI IET1 MB15 XA, #092H TMOD1, XA XA, #00000000B TC2, XA NRZ XA, #01101100B TM1, XA ; Sets the mode and starts the timer. ; Enables the interrupts. ; Enables the timer (channel 1) interrupts. ; Sets the no return zero data to “1”. ; Sets the modulo (carrier clock output period). ; or CLR1 MBE ; MOV MOV RETI XA, #049H TMOD1, XA ; Updates the modulo (low-level output period). 9 ms 4.5 ms 192 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (c) A custom code (the carrier clock output period is 0.56 ms and low-level output period is 1.69 ms when data is “1”, and carrier clock output period is 0.56 ms and low-level output period is 0.56 ms when data is “0”) is output. See the illustration below (@ fX = 4.19 MHz). • Set the high-order 4 bits of the mode register (TM1) to 0011B and select the longest setup time 1.95 ms. • Set the low-order 4 bits of the TM1 to 1100B and select the 8-bit timer/event counter mode and count operation and indicate timer start. • Set the modulo register (TMOD1) to the following initial value. 0.56 ms 7.64 µs – 1 = 73.3 – 1 ≅ 72 = 48H • When data is “0” during the period in which the carrier output is not specified by TMOD1, the processing is performed for the same duration as the output period. When data is “1”, the processing time is three times longer than the output period. • Set the high-order 4 bits of the TC2 to 0000B and disable the gate control. • Set the low-order 4 bits of the TC2 to 0000B, and if no return zero data is “1”, output the carrier clock and set the next no return zero data to “0”. • Set the transmit data (“0” or “1”) in the bit sequential buffer. Data "1" Data "0" 0.56 ms 1.69 ms 0.56 ms 0.56 ms 193 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION In this example, it is assumed that the output latch of the PTO2 pin is fixed to “0” and the pin is set in the output mode. It is also assumed that the carrier clock is being generated by the program in above. ; SEND_CARIER_DATA_PRO SEL MOV MB15 HL, #00H ; or CLR1 MBE ; Sets pointer of BSB (bit sequential buffer) to L. H is used to save bit data of BSB temporarily. ; CG_Init & Send_1st_Data MOV MOV MOV MOV SET1 MOV MOV ; Send_1st_Data CALL CALL SKE BR CALL !GET_DAT !SEND_D_0 H, #1H SEND_1_F !SEND_D_1 ; Gets data from BSB ; Outputs carrier with data 0 and 1, and sets low-level output period once. ; If bit 0 is 1, adds low-level output period twice. ; If bit 0 is 0, searches next data with low-level output. ; Adds two low-level output periods. Transmits data of bits 0 to F of BSB with PTO2 pin outputting low-level. SEND_1_F: SET1 NRZB ; Transmits data of bits 0 to F of BSB. ; Sets NRZB to 1 during low-level output period of previous data so that carrier of data transmitted next is output on next generation of IRQT1. INCS BR BR L LOOP_C_0 SEND_END ; Counts transmit data. If L changes from 0FH to 0H, ends data transmission. XA, #48H TMOD1, XA XA, #00000000B TC2, XA NRZ XA, #01101100B TM1, XA ; Sets “1” to no return zero flag. ; Selects count pulse, and sets 8-bit timer/event counter mode. ; Enables timer/event count operation, and starts timer. ; Sets modulo register (carrier clock output period). ; Disables gate control, enables output of carrier clock, and initializes NRZB and NRZ to 0. 194 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION LOOP_C_0: SKTCLR IRQT1 BR CLR1 CALL CALL SKE BR CALL BR SEND_END: ; GET_DAT: SKT MOV MOV MOV RET SEND_D_0: LOOP_1st: SKTCLR IRQT1 BR RET SEND_D_1: CLR1 BR CLR1 BR RET NRZB LOOP_2nd NRZB LOOP_3rd LOOP_1st BSB0, @L A, #0 A, #1 H, A LOOP_C_0 ; Waits low-level output of previous data (acknowledges end of previous data). ; Starts carrier output. NRZB !GET_DAT !SEND_D_0 H, #1H SEND_1_F !SEND_D_1 SEND_1_F ; Clears NRZB to 0 in advance so that first low-level output is performed on next generation of IRQT1. ; If data gotten is 1, adds low-level output period twice (SEND_D_1). ; If data is 0, transmits next data with PTO2 pin outputting low-level. ; End of transmitting 16 bits of data. ; Searches data of BSB indicated by @L. Sets value to H register. ; Outputs carrier with data 0 and 1 and sets low-level output once. ; Waits carrier output. ; Starts first low-level output. ; If data is 1, sets second low-level output. ; Waits first low-level output. ; Starts second low-level output. ; Sets third low-level output. ; Waits second low-level output. ; Starts third low-level output. LOOP_2nd: SKTCLR IRQT1 LOOP_3rd: SKTCLR IRQT1 195 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.5.6 Notes on using timer/event counter (1) Error when starting the timer During the time from the timer start (bit 3 of the TMn is set to “1”) to the match signal generation, an error of one count pulse (CP) at maximum is produced with respect to the value obtained by the formula: (value set in modulo register + 1) × resolution. This is because the count register Tn is cleared asynchronously with the CP as shown below. Count pulse (CP) Count register (Tn) ,, ,, ,, ,, ,, 0 1 2 3 0 1 Timer start Timer start 0 1 2 0 Timer start Timer start 2 When the frequency of CP is one machine cycle or more, the time from the timer start (bit 3 of the TMn is set to “1”) to the match signal generation has an error of two clock pulses at maximum to the value obtained by the formula: (value set in modulo register + 1) × resolution. This is because the Tn is cleared asynchronously with the CP based on the CPU clock as shown below. Count pulse (CP) Count register (Tn) 196 ,, ,,, ,, ,, ,, ,,, 1 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (2) Caution on starting the timer The count register Tn and interrupt request flag IRQTn are always cleared when the timer starts (bit 3 of the TMn is set to “1”). On the other hand, when the timer is operating and the IRQTn is set and the timer starts at the same timing, the IRQTn may not be able to be cleared. This does not cause trouble when the IRQTn is used as a vectored interrupt. However, when the IRQTn is tested, it appears to be set although the timer has started. Therefore, when the timer starts at the timing when the IRQTn may be set high, the timer must stop (bit 2 of the TMn is set to “0”) and then restart or the timer start operation must be done twice. Example Timer start at the timing when the IRQTn may be set high SEL MOV MOV MOV MOV or SEL SET1 SET1 MB15 TMn.3 TMn.3 ; Restart MB15 XA, #0 TMn, XA XA, #4CH TMn, XA ; Restart ; Timer stop (3) Error when reading the count register The count register (Tn) can be read any time by an 8-bit data memory manipulation instruction. When the instruction is being executed, the count pulse (CP) does not change and the contents of the Tn are kept unchanged. When the power supply for the CP is input from the TIn, the CP is cut during the instruction execution time. When the internal clock is used as the CP, it is synchronous with instructions, and therefore this phenomenon does not occur. As stated above, when the TIn is input as the CP to read the Tn, a signal (which has a pulse width that does not give rise to incorrect counting even if the CP is cut) must be input. That is, the time during which count is suspended by a read instruction is one machine cycle, therefore the pulse that is input to the TIn must be wider than it. Read instruction External clock (TIn) Instruction Count pulse (CP) Count register (Tn) K–1 K K+1 K+2 Count pulse change is held by instruction Count pulse is deleted by instruction 197 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (4) Caution on changing the count pulse When the count pulse (CP) is changed by rewriting the timer/event counter mode register (TMn), the specification for the change is valid immediately after the instruction is executed. Rewrite instruction Rewrite instruction Clock A specification Clock B specification Clock A specification Clock A Clock B Count pulse (CP) Depending on the combination of clock pulses at the time the CP is changed, whisker-like clock pulses ( or in the illustration below) may be produced. In this case, incorrect counting may occur and the count register (Tn) may be disrupted. Therefore, when changing the CP, set bit 3 of the TMn to “1” and restart the timer simultaneously. Rewrite instruction Rewrite instruction Clock A specification Clock B specification Clock A specification Clock A Clock B Count pulse (CP) 198 , ,, ,, CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (5) Operation after changing the modulo register The contents of the modulo register (TMODn) and high-level period setting modulo register (TMOD2H) are rewritten by an 8-bit data memory manipulation instruction. Count pulse (CP) Modulo register (TMODn) High-level period setting modulo register (TMOD2H) n m Rewrite instruction Count register (Tn) n 0 1 m 0 Match signal Match signal If the value of the TMODn after a change is smaller than the value of the count register (Tn), the Tn continues counting and overflows to restart counting from 0. Therefore, if the value (m) after the TMODn and TMOD2H are changed is smaller than the value (n) before they are changed, the timer must restart after they are changed. Count pulse(CP) Modulo register (TMODn) High-level period setting modulo register (TMOD2H) n m Count register (Tn) x–1 n>x>m x 255 0 1 199 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (6) Caution on using the carrier generator (at the start) When a carrier clock is generated, an error of one count pulse (CP) at maximum (two clock pulses at maximum when the CP frequency is one machine cycle or more) is produced with respect to the value obtained by the formula ((modulo register value + 1) × resolution) during the high-level period of the initial carrier clock after the timer starts (the bit 3 of the TM2 is set to “1”). For details, refer to paragraph (1) Error when starting the timer. When no return zero flag (NRZ) is set to “1” and then the timer starts (the bit 3 of the TM2 is set to “1”) in case a carrier is output as the initial code, the error at the time of timer start is contained during the time the initial carrier clock is high. SET1 NRZ NRZ 0 1 TOUT F/F 0 1 0 1 0 PTO2 SET1 TM2.3 Including the error at the time of timer start Therefore, when a carrier is to be output as the initial code, start the timer (set bit 3 of the TM2 to “1”) and then set NRZ to “1”. SET1 NRZ NRZ 0 1 TOUT F/F 0 1 0 1 0 Clock PTO2 SET1 TM2.3 Including the error at the time of timer start 200 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (7) Caution on using the carrier generator (when reloading) When a carrier is output to the PTO2 pin, a delay of one carrier clock pulse at maximum occurs during the time from the reloading (the contents of the no return zero buffer flag (NRZB) are transferred to the no return zero flag (NRZ) by a timer/event counter (channel 1) interrupt generation and the contents of the NRZ are updated to “1”) to the initial carrier generation. This is because reloading is done asynchronously with the carrier clock and for keeping the carrier at the stable high level. Reloading by interrupt generation NRZB 0 1 NRZ 0 1 TOUT F/F 0 1 0 1 0 1 0 Clock PTO2 Reloading by interrupt generation NRZB 0 1 NRZ 0 1 TOUT F/F 0 1 0 1 0 1 0 Clock PTO2 A delay of one carrier clock pulse maximum occurred 201 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (8) Caution on using the carrier generator (when restarting) When the carrier clock is high (TOUT F/F is holding “1”) and reloading is to be done forcibly by directly rewriting the contents of no return zero flag (NRZ) and the timer is to restart (by setting bit 3 of TM2 to “1”), the carrier may not be output to the PTO2 pin as shown below. SET1 NRZ NRZ 0 1 TOUT F/F 0 1 0 1 1 0 1 0 Clock PTO2 Carrier is not output SET1 TM2.3 Similarly to the above, when carrier clock is high (TOUT F/F is holding “1”) and reloading is to be done forcibly by directly rewriting the contents of NRZ and the timer is to restart (by setting bit 3 of TM2 to “1”), the carrier output to the PTO2 pin may keep its high level for a longer time as shown below. CLR1 NRZ NRZ 0 1 TOUT F/F 0 1 0 1 1 0 1 0 Clock PTO2 SET1 TM2.3 High-level period of carrier is elongated. 202 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.6 Serial Interface 5.6.1 Serial interface function The µ PD753108 incorporates a clock-synchronous 8-bit serial interface consisting of the following four modes. (1) Operation stop mode This mode is used when serial transfer is not performed. The power dissipation can be reduced. (2) 3-wire serial I/O mode This mode performs data transfer in 8-bit units with three lines: serial clock (SCK), serial output (SO), and serial input (SI). In addition, it enables high speed data transfer through simultaneous transmission and reception. Because the first bit of 8-bit data for serial transfer is switchable to MSB or LSB, the µ PD753108 can be connected to any device regardless of whether its first bit is MSB or LSB. Connection to 75XL Series, 75X Series, 78K Series, and various types of peripheral I/O devices are possible. (3) 2-wire serial I/O mode This mode performs data transfer in 8-bit units with two lines: serial clock (SCK), and serial data bus (SB0 or SB1). Communication to several devices by manipulating the output level to two lines with software is possible. The levels of output to SCK and SB0 (or SB1) can be controlled by software so that they can accept any data transfer. This eliminates the need for lines that are used for hand shaking when connecting two or more devices, thus enabling more efficient use of I/O port. (4) SBI mode (serial bus interface mode) This mode enables communication to a number of devices with two lines (serial clock (SCK) and serial data bus (SB0 or SB1)) and is compliant with the NEC serial bus format. The transmitter can output an “address” for selecting the target device for serial communication, a “command” to direct to the target device, and actual “data” to the serial data bus. The receiver can identify the data as an “address”, “command”, and “data” by hardware. This function allows efficient use of the I/O port as in 2-wire serial I/O mode, and moreover, enables simpler serial interface controller for application programs. 203 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-58. Example of SBI System Configuration VDD Master CPU SCK SB0, SB1 Address Command Data Slave IC SCK SB0, SB1 Address N Serial clock Slave CPU SCK SB0, SB1 #1 Address 1 #N 5.6.2 Configuration of serial interface Figure 5-59 shows a block diagram of the serial interface. 204 Figure 5-59. Serial Interface Block Diagram Internal bus 8/4 Bit test 8 CSIM 8 8 Bit manipulation SBIC RELT Address comparator P03/SI/SB1 Selector Shift register (SIO) (8) ACKE BSYE ACKT Match (8) SET CLR SO latch D Q CMDT CHAPTER 5 Bit test Slave address register (SVA) (8) PERIPHERAL HARDWARE FUNCTION P02/SO/SB0 Selector Bus release/ command/ acknowledge detection circuit RELD CMDD ACKD Busy/ acknowledge output circuit P01/SCK Serial clock counter INTCSI INTCSI control circuit IRQCSI set signal fX/23 fX/24 fX/26 TOUT0 (from timer/ event counter) P01 output Iatch Serial clock control circuit Serial clock selector External SCK 205 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (1) Serial operation mode register (CSIM) This 8-bit register specifies the operation mode and serial clock wake-up function of the serial interface (For details, refer to 5.6.3 (1) Serial operation mode register (CSIM) ). (2) Serial bus interface control register (SBIC) This 8-bit register consists of bits that control the status of the serial bus and flags that indicate the various statuses of the data input from the serial bus. It is mainly used in the SBI mode (For details, refer to 5.6.3 (2) Serial bus interface control register (SBIC)). (3) Shift register (SIO) This register converts 8-bit serial data into parallel data or 8-bit parallel data into serial data. It performs transmission or reception (shift operation) in synchronization with the serial clock. Actual transmission or reception is controlled by writing data to the SIO (For details, refer to 5.6.3 (3) Shift register (SIO)). (4) SO latch This latch holds the levels of the SO/SB0 and SI/SB1 pins. It can also be controlled directly via software. In the SBI mode, this latch is set when SCK has been asserted eight times (For details, refer to 5.6.3 (2) Serial bus interface control register (SBIC)). (5) Serial clock selector This selects the serial clock to be used. (6) Serial clock counter This counter counts the number of serial clocks output or input when transmission or reception operation is performed, to check whether 8 bits of data have been transmitted or received. (7) Slave address register (SVA) and address comparator • In SBI mode This register and comparator are used when the µ PD753108 is used as a slave device. The slave places its specification number (slave address value) in the SVA. The master outputs a slave address to select a specific slave. The address comparator of the slave compares the slave address the slave has received from the master with the value in the SVA. When the address coincides with the SVA value, the slave is selected. • In 2-wire serial I/O mode and SBI mode When the µ PD753108 is used as a slave or master, this register and comparator detects an error (For details, refer to 5.6.3 (4) Slave address register (SVA)). 206 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (8) INTCSI control circuit This circuit controls generation of an interrupt request. The interrupt request (INTCSI) is generated in the following cases. When the interrupt request is generated, an interrupt request flag (IRQCSI) is set (Refer to Figure 6-1 Interrupt Control Circuit Block Diagram). • In 3-wire and 2-wire serial I/O modes An interrupt request is generated each time eight serial clocks have been counted. • In SBI mode When WUPNote = “0” ....... An interrupt request is generated each time eight serial clocks have been counted. When WUP = “1” ............ An interrupt request is generated when the value of SVA and that of SIO coincide after an address has been received. Note WUP ··· Wake-up function specification bit (bit 5 of CSIM) (9) Serial clock control circuit This circuit controls the supply of the serial clock to the shift register. It also controls the clock output to the SCK pin when the internal system clock is used. (10) Busy/acknowledge output circuit and bus release/command/acknowledge detection circuit These circuits output and detect control signals in the SBI mode. They do not operate in the three-wire and two-wire serial I/O modes. (11) P01 output latch This latch generates the serial clock via software after eight serial clocks have been generated. It is set to “1” when the reset signal is input. To select the internal system clock as the serial clock, set the P01 output latch to “1”. 207 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.6.3 Register function (1) Serial operation mode register (CSIM) Figure 5-60 shows the format of the serial operation mode register (CSIM). The CSIM is an 8-bit register which specifies the serial interface operation mode, serial clock, and wake-up function. The register is manipulated by an 8-bit memory manipulation instruction. The high-order 3 bits of the register can be operated bit-wise. In this case, the name of each bit is used to manipulate. Whether the read/write operation can be performed or not depends on the bit (See Figure 5-60). Bit 6 can be used only as a bit test and data written in the bit position is invalid. All the bits are cleared to 0, when a RESET signal is generated. Figure 5-60. Serial Operation Mode Register (CSIM) Format (1/4) Address FE0H 7 CSIE 6 COI 5 4 3 2 1 0 Symbol CSIM WUP CSIM4 CSIM3 CSIM2 CSIM1 CSIM0 Serial clock selection bit (W) Serial interface operation mode selection bit (W) Wake-up function specification bit (W) Signal sent from address comparator (R) Serial interface operation enable/disable specification bit (W) Remarks 1. (R) Read only. 2. (W) Write only. 208 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-60. Serial Operation Mode Register (CSIM) Format (2/4) Serial interface operation enable/disable specification bit (W) Shift Register Operation CSIE 0 1 Disable the shift operation. Enables the shift operation. Serial Clock Counter Clear Count operation IRQCSI Flag Hold SO/SB0, SI/SB1 Pins Dedicated to port 0 function Enable setting Both for the function in each mode and port 0 Remarks 1. Each mode can be selected by setting the CSIE, CSIM3, and CSIM2. CSIE 0 1 1 1 CSIM3 × 0 1 1 CSIM2 × × 0 1 Operation Mode Operation stop mode 3-wire serial I/O mode SBI mode 2-wire serial I/O mode 2. The P01/SCK pin enters the following status by setting the CSIE, CSIM1, and CSIM0. CSIE 0 1 0 0 0 1 1 1 CSIM1 0 0 0 1 1 0 1 1 CSIM0 0 0 1 0 1 1 0 1 Serial clock output (high-level output : at the end of serial data transfer) Status of P01/SCK Pin Input port (P01) High-impedance (SCK input) High-level output 3. During serial data transfer, follow the procedure ( to ) to clear the CSIE. Clear the interrupt enable flag (IECSI) and disable the interrupts. Clear the CSIE. Clear the interrupt request flag (IRQCSI). Examples 1. fX /2 4 is selected for the serial clock. A serial interrupt IRQCSI is generated at the end of serial data transfer. Serial data transfer is done in the SBI mode with the SB0 pin as the serial data bus. SEL MOV MOV MB15 XA, #10001010B CSIM, XA ; CSIM ← 10001010B ; or CLR1 MBE 2. Serial data transfer complying with the contents of the CSIM is enabled. SEL SET1 MB15 CSIE ; or CLR1 MBE 209 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-60. Serial Operation Mode Register (CSIM) Format (3/4) Signal from address comparator (R) COINote Condition To Be Cleared (COI = 0) The contents of the slave address register (SVA) are not the same as those of the shift register. Condition To Be Set (COI = 1) The contents of the slave address register (SVA) are the same as those of the shift register. Note The reading of the COI is valid only before and after serial data transfer. Uncertain data is read out during transfer. The COI data written by an 8-bit manipulation instruction is ignored. Wake-up function specification bit (W) WUP 0 1 Sets the IRQCSI at each time serial data transfer ends in each mode. Used only in the SBI mode. Sets the IRQCSI only when an address received after a bus release is equal to the data of the slave address register (wake-up status). SB0 and SB1 are high-impedance buses. Caution If WUP = 1 while a BUSY signal is output, BUSY is not released. The BUSY signal is output during the time from the release of BUSY to the falling edge of serial clock (SCK) in the SBI. When making WUP = 1, be sure to release the BUSY status and then assure the SB0 (or SB1) pin is high. Serial interface operation mode selection bit (W) CSIM4 × CSIM3 0 CSIM2 0 1 0 1 0 SBI mode Operation Mode 3-wire serial I/O mode Shift Register Bit Order SO/SB0/P02 Pin Function SI/SB1/P03 Pin Function SIO7-0 ↔ XA SO (CMOS output) (transferred at MSB first) SIO0-7 ↔ XA (transferred at LSB first) SIO7-0 ↔ XA SB0 (transferred at MSB first) (N-channel open-drain I/O) P02 (CMOS input) P03 (CMOS input) SI (CMOS input) 1 SB1 (N-channel open-drain I/O) P03 (CMOS input) 0 1 1 2-wire serial I/O mode SIO7-0 ↔ XA SB0 (transferred at MSB first) (N-channel open-drain I/O) P02 (CMOS input) 1 SB1 (N-channel open-drain I/O) Remark × : don’t care 210 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-60. Serial Operation Mode Register (CSIM) Format (4/4) Serial clock selection bit (W) Serial Clock CSIM1 0 0 1 1 CSIM0 0 1 0 1 3-wire Serial I/O Mode Clock input from outside to SCK pin Timer/event counter output (TOUT0) fX/2 4 (375 kHz: 6.00-MHz operation, 262 kHz: 4.19-MHz operation) fX/2 3 (750 kHz: 6.00-MHz operation, 524 kHz: 4.19-MHz operation) fX/26 93.8 kHz: 6.00-MHz operation, 65.5 kHz: 4.19-MHz operation SBI Mode 2-wire Serial I/O Mode SCK Pin Mode Input Output (2) Serial bus interface control register (SBIC) Figure 5-61 shows the format of the serial bus interface control register (SBIC). The SBIC is an 8-bit register which is composed of the bits controlling the serial bus and the flags indicating the status of input data. It is used mainly in the SBI mode. It is manipulated by a bit manipulation instruction. It cannot be manipulated by an 8-bit/4-bit manipulation instruction. Whether the read/write operation can be performed or not depends on the bit (See Figure 5-61). All the bits are cleared to 0 when RESET signal is generated. Caution Only the following bits can be used in the 3-wire and 2-wire serial I/O modes. • Bus release trigger bit (RELT) ........... sets the SO latch. • Command trigger bit (CMDT) ............. clears the SO latch. Figure 5-61. Serial Bus Interface Control Register (SBIC) Format (1/3) Address FE2H 7 6 5 4 3 2 1 0 Symbol SBIC Bus release trigger bit (W) BSYE ACKD ACKE ACKT CMDD RELD CMDT RELT Command trigger bit (W) Bus release detection flag (R) Command detection flag (R) Acknowledge trigger bit (W) Acknowledge enable bit (R/W) Acknowledge detection flag (R) Busy enable bit (R/W) Remarks 1. (R) 2. (W) : Read only. : Write only. 3. (R/W) : Both read/write. 211 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-61. Serial Bus Interface Control Register (SBIC) Format (2/3) Busy enable bit (R/W) BSYE 0 Disables the automatic output of a busy signal. Stops the output of a busy signal in synchronization with the falling edge of the SCK immediately after a clear instruction is executed. 1 Outputs a busy signal in synchronization with the falling edge of the SCK following an acknowledge signal. Examples 1. A command signal is output. SEL SET1 MB15 CMDT ; or CLR1 MBE 2. The RELD and CMDD are tested to identify the received data for an appropriate operation. The interrupt routine sets the WUP to 1 and is executed only when the address is matched. SEL SKF BR SKT BR BR MB15 RELD !ADRS CMDD !DATA !CMD ; Tests the CMDD. ; Tests the RELD. CMD : ....................... ; Interprets the command. DATA : ....................... ; Processes the data. ADRS : ....................... ; Decodes the address. Acknowledge detection flag (R) ACKD Condition To Be Cleared (ACKD = 0) At the start of data transfer When the RESET signal is generated. Condition To Be Set (ACKD = 1) When acknowledge signal (ACK) is detected (in synchronization with the rising edge of the SCK). Acknowledge enable bit (R/W) ACKE 0 1 Disables the automatic output of the acknowledge signal (ACK). Output by the ACKT is enabled. When it is set before data transfer terminates When it is set after data transfer terminates The ACK is output in synchronization with the 9th clock pulse of SCK. The ACK is output in synchronization with the SCK immediately after a set instruction is executed. Acknowledge trigger bit (W) ACKT When it is set at the end of data transfer, the ACK is output in synchronization with the next SCK. It is automatically cleared to 0 after the ACK is output. Cautions 1. Do not set this bit to 1 before the end of serial transfer or during transfer. 2. The ACKT cannot be cleared by software. 3. When setting the ACKT, set the ACKE to 0. 212 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-61. Serial Bus Interface Control Register (SBIC) Format (3/3) Command detection flag (R) CMDD Condition To Be Cleared (CMDD = 0) When transfer start instruction is being executed. When bus release signal (REL) is detected. When the RESET signal is generated. CSIE = 0 (see Figure 5-60) Condition To Be Set (CMDD = 1) When command signal (CMD) is detected. Bus release detection flag (R) RELD Condition To Be Cleared (RELD = 0) When transfer start instruction is being executed. When the RESET signal is generated. CSIE = 0 (see Figure 5-60) SVA is not equal to SIO when an address is received. Condition To Be Set (RELD = 1) When bus release signal (REL) is detected. Command trigger bit (W) CMDT Trigger output control bit for the command signal (CMD). When it is set (CMDT = 1), the SO latch is cleared to 0 and then CMDT bit is automatically cleared to 0. Caution The SB0 (or SB1) must not be cleared during serial data transfer, but before or after it. Bus release trigger bit (W) RELT Trigger output control bit for the bus release signal (REL). When it is set (RELT = 1), the SO latch is set to 1 and then RELT bit is automatically cleared to 0. Caution The SB0 (or SB1) must not be cleared during serial data transfer, but before or after it. 213 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (3) Shift register (SIO) Figure 5-62 shows the configuration of the system comprising the shift register and peripheral devices. The SIO is an 8-bit register which performs parallel-to-serial conversion and shift operation in synchronization with the serial clock. Serial data transfer starts when data is entered into the SIO. During data transmission, the data written in the SIO is output to the serial output (SO) or serial data bus (SB0 or SB1). During receiving, data is read from the serial input (SI) or SB0 (or SB1) to the SIO. Data can be read and written by an 8-bit manipulation instruction. When a RESET signal is generated during an operation, the contents of the SIO are uncertain. When the RESET signal is generated in the standby mode, the contents of the SIO are held. The shift operation stops after data is transmitted or received in an 8-bit unit. Figure 5-62. System Comprising Shift Register and Peripheral Devices Configuration Internal bus Shift register Address comparator RELT CMDT SET D CLK CLR Q SO latch CSIM Shift clock BUSY/ACK N-ch open-drain output Data can be written and read to/from the SIO in the following timings. • The serial interface operation enable/disable bit (CSIE) is set to 1 except when the CSIE is set to 1 after data is written in the shift register. • The serial clock is masked after the 8-bit serial data transfer ends. • The SCK is high. Be sure to write or read data to or from the SIO when SCK is high. The input pin of the data bus is shared with the output pin in the two-wire serial I/O mode and SBI mode. The output pin is of the N-ch open-drain configuration. Therefore, set FFH in the SIO of the device that is to receive data. 214 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (4) Slave address register (SVA) SVA is an 8-bit register that sets a slave address (specification number). It is operated by an 8-bit manipulation instruction. The contents of the SVA becomes uncertain when a RESET signal is generated. However, when the RESET signal is generated in the standby mode, the contents of the SVA are held. (a) Detection of slave address (in SBI mode) When the µ PD753108 is connected to the serial bus as a slave device, SVA is used to set the slave address (specification number) of the µPD753108. The master outputs a slave address to the slaves connected to the bus, to select a specific slave. The slave address output from the master is compared with the value of the SVA of the slave by the address comparator of the slave. When the two addresses coincide, the slave is selected. At this time, the bit 6 (COI) of the serial operation mode register (CSIM) is set to “1”. When an address is received from the master and coincidence between the received address and the address set to the SVA is not detected, the bus release detection flag (RELD) is cleared to 0. IRQCSI is set only when coincidence is detected when WUP = 1. This interrupt function allows the slave (µ PD753108) to learn that the master has issued a request for communication. (b) Detection of errors (in 2-wire serial I/O mode and SBI mode) The SVA detects an error in the following cases: • When the µ PD753108 operates as the master and transmits addresses, commands, and data • When the µ PD753108 transmits data as a slave device For details, refer to 5.6.6 (6) Error detection or 5.6.7 (8) Error detection. 215 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.6.4 Operation stop mode The operation stop mode is used when serial transfer is not performed, to reduce the power dissipation. In this mode, the shift register does not perform shift operations. Therefore, it can be used as an ordinary 8bit register. When the reset signal is input, operation stop mode is set. The P02/SO/SB0 and P03/SI/SB1 pins are set to the input port mode. The P01/SCK pin can be used as an input port pin if so specified by the serial operation mode register. [Register setting] Operation stop mode is set by using the serial operation mode register (CSIM) (For the format of the CSIM, refer to 5.6.3 (1) Serial operation mode register (CSIM)). The CSIM is manipulated by an 8-bit manipulation instruction. However, the CSIE bit of this register can be manipulated in 1-bit units. The name of the bit can be used for manipulation. The CSIM is set to 00H at reset. The shaded portions in the figure below indicate the bits used in operation stop mode. Address FE0H Symbol CSIM 7 CSIE 6 COI 5 4 3 2 1 0 WUP CSIM4 CSIM3 CSIM2 CSIM1 CSIM0 Serial clock select bits (W)Note Serial interface operation mode select bits (W) Wake-up function specification bit (W) Coincidence signal from address comparator (R) Serial interface operation enable/disable bit (W) Note This bit can select the status of the P01/SCK pin. Remark (R) : read only (W) : write only Serial interface operation enable/disable bit (W) Operation of Shift Register CSIE 0 Shift operation disabled Serial Clock Counter Cleared IRQCSI Flag Retained SO/SB0 and SI/SB1 Pins Dedicated to port 0 function 216 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Serial clock select bit (W) The P01/SCK pin is set to the following status according to the setting of the CSIM0 and CSIM1 bits. CSIM1 0 0 1 1 CSIM0 0 1 0 1 Status of P01/SCK Pin High impedance High level Clear the CSIE bit using the following procedure during serial transfer: Clear the interrupt enable flag (IECSI) to disable the interrupt. Clear CSIE. Clear the interrupt request flag (IRQCSI). 217 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.6.5 Operation in 3-wire serial I/O mode In the 3-wire operation mode, the µ PD753108 can be connected to microcontrollers in the 75XL Series, 75X Series, and 78K Series, and to various peripheral I/O devices. In this mode, communication is established by using three lines: serial clock (SCK), serial output (SO), and serial input (SI). Figure 5-63. Example of System Configuration in 3-wire Serial I/O Mode 3-wire serial I/O ↔ 3-wire serial I/O Master CPU µ PD753108 SCK Slave CPU SCK SO SI SI SO Remark The µ PD753108 can be also used as a slave CPU. (1) Register setting When 3-wire serial I/O mode is used, the following two registers must be set: • Serial operation mode register (CSIM) • Serial bus interface control register (SBIC) 218 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (a) Serial operation mode register (CSIM) When 3-wire serial I/O mode is used, set CSIM as shown below (For the format of CSIM, refer to 5.6.3 (1) Serial operation mode register (CSIM)). CSIM is manipulated by using 8-bit manipulation instructions. Bits 7, 6, and 5 can also be manipulated in 1-bit units. The contents of the CSIM are cleared to 00H at reset. The shaded portion in the figure indicates the bits used in 3-wire serial I/O mode. Address FE0H 7 CSIE 6 COI 5 4 3 2 1 0 Symbol CSIM WUP CSIM4 CSIM3 CSIM2 CSIM1 CSIM0 Serial clock select bits (W) Serial interface operation mode select bits (W) Wake-up function specification bit (W) Coincidence signal from address comparator (R) Serial interface operation enable/disable bit (W) Remark (R) : read only (W) : write only Serial interface operation enable/disable bit (W) Operation of Shift Register CSIE 1 Shift operation enabled Serial Clock Counter Count operation IRQCSI Flag Can be set SO/SB0 and SI/SB1 Pins Function in each mode and port 0 function shared Signal from address comparator (R) COI Note Clear Condition (COI = 0) When the slave address register (SVA) data and shift register data do not coincide Set Condition (COI = 1) When slave address register (SVA) data and shift register data coincide Note COI can be read before the start of serial transfer and after completion of the serial transfer. An undefined value is obtained if this bit is read during transfer. Data written to COI by an 8-bit manipulation instruction is ignored. Wake-up function specification bit (W) WUP 0 Sets IRQCSI each time serial transfer is completed 219 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Serial interface operation mode select bit (W) CSIM4 × CSIM3 0 CSIM2 0 1 Bit Order of Shift Register SIO7-0 ↔ XA (MSB first) SIO0-7 ↔ XA (LSB first) SO Pin Function SO (CMOS output) SI Pin Function SI (CMOS input) Remark ×: don’t care Serial clock select bit (W) CSIM1 0 0 1 1 CSIM0 0 1 0 1 Serial Clock External clock input to SCK pin Timer/event counter output (TOUT0) f X/24 (262 kHz)Note f X/23 (524 kHz)Note SCK Pin Mode Input Output Note The frequency in parentheses applies when f X = 4.19-MHz operation. (b) Serial bus interface control register (SBIC) When the three-wire serial I/O mode is used, set SBIC as shown below (For the format of SBIC, refer to 5.6.3 (2) Serial bus interface control register (SBIC)). This register is manipulated by using bit manipulation instructions. The contents of SBIC are cleared to 00H at reset. The shaded portion in the figure indicates the bits used in the three-wire serial I/O mode. Address FE2H 7 6 5 4 3 2 1 0 Symbol SBIC Bus release trigger bit (W) Command trigger bit (W) BSYE ACKD ACKE ACKT CMDD RELD CMDT RELT                      Do not use these bits in 3-wire serial I/O mode. Remark (W): write only Command trigger bit CMDT This bit controls the output trigger of a command signal (CMD). When this bit is set to 1, the SO latch is cleared to 0. After that, the CMDT bit is automatically cleared to 0. Bus release trigger bit (W) RELT This bit controls the output trigger of a bus release signal (REL). When this bit is set to 1, the SO latch is set to 1. After that, the RELT bit is automatically cleared to 0. Caution Do not use bits in the SBIC register other than CMDT and RELT in the 3-wire serial I/O mode. 220 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (2) Communication operation The 3-wire serial I/O mode transmit/receive data in 8-bit units. Data is transferred one bit at a time in synchronization with a given serial clock. Shift register shift operation is performed in synchronization with the serial clock (SCK) falling edge. Transmit data is retained in the SO latch and output from the SO pin. On the SCK rising edge, receive data input to the SI pin is latched in the shift register. When 8-bit transfer terminates, shift register operation automatically stops and the interrupt request flag (IRQCSI) is set. Figure 5-64. 3-wire Serial I/O Mode Timing SCK 1 2 3 4 5 6 7 8 SI DI7 DI6 DI5 DI4 DI3 DI2 DI1 DI0 SO DO7 DO6 DO5 DO4 DO3 DO2 DO1 DO0 IRQCSI Transfer start in synchronization with SCK falling edge. Execution of data write instruction into SIO (transfer start indication) When CSIE is set (1), IRQCSI is automatically cleared (0). Transfer termination Because the SO pin is a CMOS output pin and outputs the status of the SO latch, the output status of the SO pin can be manipulated by setting the RELT and CMDT bits. However, do not perform this manipulation during serial transfer. The output status of the SCK pin can be controlled by manipulating the P01 latch in the output mode (mode of the internal system clock) (Refer to 5.6.8 SCK pin output manipulation). 221 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (3) Selecting the serial clock The serial clock is selected by using bits 0 and 1 of the serial operation mode register (CSIM). The following four types of serial clocks can be selected: Table 5-9. Selection of Serial Clock and Applications (in 3-wire serial I/O mode) Mode Register CSIM1 0 0 CSIM0 0 1 Source External SCK TOUT F/F fX/2 4 fX/2 3 Serial Clock Timing at Which Shift Register Can Be Read/ Masking Serial Clock Written and Serial Transfer Can Be Started In operation enable mode (CSIE = 1) If serial clock is masked after 8-bit serial transfer When SCK is high Application Slave CPU Half duplex start-stop synchronization transfer (software control) Medium-speed serial transfer High-speed serial transfer Automatically masked at end of transfer of 8-bit data 1 1 0 1 (4) Signals Figure 5-65 illustrates the operation of RELT and CMDT. Figure 5-65. Operation of RELT and CMDT SO latch RELT CMDT 222 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (5) Transfer first bit change between MSB and LSB The 3-wire serial I/O mode enables selection of the most significant bit (MSB) or least significant bit (LSB) for the transfer first bit. Figure 5-66 shows the shift register (SIO) and internal bus configuration. As shown in Figure 5-66, MSB and LSB can be reversed for read/write. MSB or LSB can be specified as the transfer first bit by setting serial operation mode register (CSIM) bit 2. Figure 5-66. Transfer Bit Change Circuit 7 6 Internal bus 1 0 LSB first MSB first Read/write gate Read/write gate SO latch SI Shift register (SIO) D Q SO SCK The transfer first bit is switched by changing the bit order of data write into the shift register (SIO). The SIO shift order is always the same. Change the transfer first bit between MSB and LSB before writing data into the shift register. 223 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (6) Starting transfer Serial transfer is started when the transfer data is placed in the shift register (SIO), if the following two conditions are satisfied: • Serial interface operation enable/disable bit (CSIE) = 1 • The internal serial clock is stopped after 8-bit serial transfer or SCK is high Caution Transfer is not started even if CSIE is set to “1” after the data has been written to the shift register. When an 8-bit transfer has been completed, the serial transfer is automatically stopped, and an interrupt request flag (IRQCSI) is set. Example To transfer the RAM data specified by the HL register to SIO and, at the same time, load the data in SIO to the accumulator and start serial transfer MOV SEL XCH XA, @HL MB15 XA, SIO ; Fetches out transfer data from RAM ; or CLR1 MBE ; Exchanges transmit data and receive data, and starts transfer 224 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (7) Applications using 3-wire serial I/O mode Example 1. To transfer data, MSB first, with 262-kHz transfer clock (at 4.19 MHz) (master operation) CLR1 MOV MOV MOV MOV Caution MBE XA, #10000010B CSIM, XA XA, TDATA SIO, XA ; Sets transfer mode ; TDATA is address storing transfer data ; Sets transfer data and starts transfer After transfer has been started for the first time, transfer can be started by writing data to SIO (by using MOV SIO, XA or XCH XA, SIO) the second and later times. µ PD753108 µ PD7225G (LCD controller/driver), etc. SCK SO/SB0 SCK SI In this example, the SI/SB1 pin of the µ PD753108 can be used as an input pin. 225 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Example 2. To transmit or receive data, LSB first, with an external clock (slave operation) (In this example, the shift register is read/written using a function that reverses the MSB-LSB order.) µ PD753108 Other microcontroller P01/SCK SI/SB1 SO/SB0 SCK SO SI Main routine CLR1 MOV MOV MOV MOV EI EI Interrupt routine (MBE = 0) MOV XCH MOV RETI XA, TDATA XA, SIO RDATA, XA ; Receive data ↔ transmit data, starts transfer ; Saves receive data MBE XA, #84H CSIM, XA XA, TDATA SIO, XA IECSI ; Sets transfer data and starts transfer ; Stops serial operation, MSB/LSB inverse mode, external clock 226 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Example 3. To transmit or receive data at high speeds using a 524-kHz (at 4.19 MHz) transfer clock µ PD753108 (master) µ PD75206, etc. SCK SO/SB0 SI/SB1 SCK SI SO ··· Master CLR1 MOV MOV MOV MOV . . . . . . LOOP: SKTCLR BR MOV MBE XA, #10000011B CSIM, XA XA, TDATA SIO, XA ; Sets transfer data and starts transfer ; Sets transfer mode IRQCSI LOOP XA, SIO ; Test IRQCSI ; Receives data 227 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.6.6 Operation in 2-wire serial I/O mode The 2-wire serial I/O mode can be used in any communication format if so specified by program. Basically, communication is established by using two lines: serial clock (SCK) and serial data input/output (SB0 or SB1). Figure 5-67. Example of System Configuration in 2-wire Serial I/O Mode 2-wire serial I/O ↔ 2-wire serial I/O Master CPU ( µ PD753108) SCK Slave CPU SCK VDD SB0, SB1 SB0, SB1 Remark The µ PD753108 can be also used as a slave CPU. (1) Register setting When the 2-wire serial I/O mode is used, the following two registers must be set: • Serial operation mode register (CSIM) • Serial bus interface control register (SBIC) 228 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (a) Serial operation mode register (CSIM) When the 2-wire serial I/O mode is used, set CSIM as shown below (For the format of CSIM, refer to 5.6.3 (1) Serial operation mode register (CSIM)). CSIM is manipulated by using an 8-bit manipulation instructions. Bits 7, 6, and 5 can also be manipulated in 1-bit units. The contents of the CSIM are cleared to 00H at reset. The shaded portion in the figure indicates the bits used in the 2-wire serial I/O mode. Address FE0H 7 CSIE 6 COI 5 4 3 2 1 0 Symbol CSIM WUP CSIM4 CSIM3 CSIM2 CSIM1 CSIM0 Serial clock select bits (W) Serial interface operation mode select bits (W) Wake-up function specification bit (W) Coincidence signal from address comparator (R) Serial interface operation enable/disable bit (W) Remark (R) : read only (W): write only Serial interface operation enable/disable bit (W) Operation of Shift Register CSIE 1 Shift operation enabled Serial Clock Counter Count operation IRQCSI Flag Can be set SO/SB0 or SI/SB1 Pin Function in each mode and port 0 function shared Signal from address comparator (R) COI Note Clear Condition (COI = 0) When slave address register (SVA) data and shift register data do not coincide Set Condition (COI = 1) When slave address register (SVA) data and shift register data coincide Note COI can be read before the start of a serial transfer or after completion of a serial transfer. An undefined value is read if this bit is read during transfer. Data written to COI by an 8-bit manipulation instruction is ignored. Wake-up function specification bit (W) WUP 0 Sets IRQCSI each time serial transfer is completed 229 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Serial interface operation mode select bit (W) CSIM4 0 1 CSIM3 1 CSIM2 1 Bit Order of Shift Register SIO7-0 ↔ XA (MSB first) SB0/P02 Pin Function SB0 (N-ch open-drain I/O) P02 (CMOS input) SB1/P03 Pin Function P03 (CMOS input) SB1 (N-ch open-drain I/O) Serial clock select bit (W) CSIM1 0 0 1 1 CSIM0 0 1 0 1 Serial Clock External clock input to SCK pin Timer/event counter output (TOUT0) f X/26 (65.5 kHz) Note SCK Pin Mode Input Output Note The frequency in parentheses applies when f X = 4.19-MHz operation. (b) Serial bus interface control register (SBIC) When the 2-wire serial I/O mode is used, set SBIC as shown below (For the format of SBIC, refer to 5.6.3 (2) Serial bus interface control register (SBIC)). This register is manipulated by using bit manipulation instructions. The contents of SBIC are cleared to 00H at reset. The shaded portion in the figure indicates the bits used in the 2-wire serial I/O mode. Address FE2H Symbol SBIC 7 6 5 4 3 2 1 0 BSYE ACKD ACKE ACKT CMDD RELD CMDT RELT                      Do not use these bits in 2-wire serial I/O mode. Bus release trigger bit (W) Command trigger bit (W) Remark (W): write only Command trigger bit CMDT This bit controls the output trigger of a command signal (CMD). When this bit is set to 1, the SO latch is cleared to 0. After that, the CMDT bit is automatically cleared to 0. Bus release trigger bit (W) RELT This bit controls the output trigger of a bus release signal (REL). When this bit is set to 1, the SO latch is set to 1. After that, the RELT bit is automatically cleared to 0. Caution Do not use bits of the SBIC register other than CMDT and RELT in 2-wire serial I/O mode. 230 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (2) Communication operation The 2-wire serial I/O mode transmits/receives data in 8-bit units. Data is transferred one bit at a time in synchronization with a given serial clock. Shift register shift operation is performed in synchronization with the serial clock (SCK) falling edge. Transmit data is retained in the SO latch and output starting at the MSB from the SB0/P02 (or SB1/P03) pin. On the SCK rising edge, receive data input from the SB0 (or SB1) pin is latched in the shift register. When an 8-bit transfer terminates, shift register operation automatically stops and the interrupt request flag (IRQCSI) is set. Figure 5-68. 2-wire Serial I/O Mode Timing SCK 1 2 3 4 5 6 7 8 SB0, SB1 D7 D6 D5 D4 D3 D2 D1 D0 IRQCSI Transfer termination Transfer start in synchronization with SCK falling edge Execution of data write instruction into SIO (transfer start indication) The SB0 (or SB1) pin specified for the serial data bus becomes N-ch open-drain input/output, thus must be pulled high with an external pull-up resistor. Because it is necessary to turn off the N-ch transistor when data is received, write FFH to SIO in advance. Since the SB0 (or SB1) pin outputs the SO latch state, the SB0 (or SB1) pin output state can be manipulated by setting the RELT and CMDT bits. However, do not perform this manipulation during serial transfer. In the output mode (internal system clock mode), the SCK pin output state can be controlled if the P01 output latch is manipulated (See 5.6.8 SCK pin output manipulation). 231 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (3) Selecting the serial clock The serial clock is selected by using the bits 0 and 1 of the serial operation mode register (CSIM). Three types of serial clocks can be selected: Table 5-10. Selection of Serial Clock and Applications (in 2-wire serial I/O mode) Mode Register CSIM1 0 0 1 1 CSIM0 0 1 0 1 Source External SCK TOUT F/F fX/2 6 Serial Clock Timing at Which Shift Register Can Be Read/ Masking Serial Clock Written and Serial Transfer Can Be Started In operation enable mode (CSIE = 1) If serial clock is masked after 8-bit serial transfer When SCK is high Application Slave CPU Serial transfer at any speed Low-speed serial transfer Automatically masked at end of transfer of 8-bit data (4) Signals Figure 5-69 illustrates the operation of RELT and CMDT. Figure 5-69. Operation of RELT and CMDT SO latch RELT CMDT 232 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (5) Starting transfer Serial transfer is started when the transfer data is placed in the shift register (SIO), if the following two conditions are satisfied: • Serial interface operation enable/disable bit (CSIE) = 1 • The internal serial clock is stopped after 8-bit serial transfer, or SCK is high Cautions 1. Transfer is not started even if CSIE is set to “1” after the data has been written to the shift register. 2. Because it is necessary to turn off the N-ch transistor when data is received, write FFH to SIO in advance. When an 8-bit transfer has been completed, serial transfer is automatically stopped, and an interrupt request flag (IRQCSI) is set. (6) Error detection In 2-wire serial I/O mode, because the status of the serial bus SB0 or SB1 during transmission is also loaded to the shift register SIO of the device transmitting data, an error can be detected by the following methods: (a) By comparing SIO data before and after transmission If the two data differ from each other, it can be assumed that a transmission error has occurred. (b) By using the slave address register (SVA) The transmit data is placed in SIO and SVA and transmission is executed. After transmission, the COI bit (coincidence signal from the address comparator) of the serial operation mode register (CSIM) is tested. If this bit is “1”, the transmission has been completed normally. If it is “0”, it can be assumed that a transmission error has occurred. 233 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (7) Application using 2-wire serial I/O mode 2-wire serial I/O mode can be used to connect multiple devices by configuring a serial bus. Example To configure a system by connecting the µ PD753108 as the master and µ PD75104, µ PD75402A, and µ PD7225G as slaves VDD µ PD753108 (master) Port SCK SO/SB0 CS µ PD7225G SCK SI µ PD75402A SCK SI SO µ PD75104 SCK SI SO The SI and SO pins of the µ PD75104 are connected together. When serial data is not output, the serial operation mode register is manipulated so that the output buffer is turned off to release the bus. Because the SO pin of the µ PD75402A cannot go into a high-impedance state, a transistor is connected to the SO pin as shown in the figure, so that the SO pin can be used as an open-collector output pin. When data is input to the µ PD75402A, the transistor is turned off by writing 00H to the shift register in advance. The timing of when each microcontroller outputs data is determined in advance. The serial clock is output by the µ PD753108, which is the master. All the slave microcontrollers operate on an external clock. 234 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.6.7 SBI mode operation The SBI (serial bus interface) is a high-speed serial interface system which is compliant with the NEC serial bus format. The SBI is a high-speed serial bus of a single master; bus configuration function is added to the clocked serial I/O system so that the master can communicate with a number of devices by using two signal lines. When microcontrollers and peripheral ICs make up a serial bus, the number of ports and wiring on the printed circuit boards can be reduced. The master can output an “address” to select the slave device with which it is to communicate, a “command” to tell the slave which operation to perform, and actual “data”, via the serial data bus. The slave identifies the data it has received from the master as an “address”, “command”, or “data” by using hardware. This SBI function simplifies the portion of the application program that controls the serial interface. The SBI function is provided in several devices such as the “75XL Series”, “75X Series”, and 8- and 16-bit singlechip microcontrollers in the “78K Series”. Figure 5-70 shows an example of the configuration of the serial bus with CPUs and peripheral ICs having a serial interface conforming to SBI. Figure 5-70. SBI System Configuration Example VDD Master CPU Slave CPU µ PD753108 SB0, SB1 µ PD753108 SB0, SB1 Address 1 SCK SCK Slave CPU SB0, SB1 Address 2 SCK Slave IC SB0, SB1 Address N SCK Cautions 1. Since the serial data bus pin SB0 (or SB1) is open-drain output in the SBI, the serial data bus line is in the wired-OR status. The serial data bus line needs a pull-up resistor. 2. When master-slave exchange is to be performed, the I/O switching of the serial clock line (SCK) is done asynchronously between the master and slave, therefore the pull-up resistor is also necessary for the SCK. 235 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (1) Function of SBI If two or more devices are connected to configure a serial bus with the existing serial I/O method, many ports and much wiring are necessary to distinguish among the chip select signal, command, and data, and to identify the busy status, because the existing serial I/O method only provides a data transfer function. Moreover, if software performs these manipulations, the workload of the software increases. In the SBI mode, the serial bus can be configured by using only two lines: serial clock SCK and serial data bus SB0 or SB1. Therefore, the number of ports can be reduced and the wiring on the printed circuit board can be shortened. The functions of the SBI mode are described below. (a) Address/command/data identification function Serial data is identified as an address, command, or data. (b) Chip select function by using address The master transmits an address to a slave to select the slave (chip select). (c) Wake-up function The slave can judge whether it has received an address (whether the slave has received the chip select signal from the master) by using the wake-up function (which can be set or cleared via software). When the wake-up function is set, an interrupt (IRQCSI) is generated when the slave has received an address coinciding with its own address. Therefore, even when the master communicates with two or more slaves, the slaves other than that selected by the master can operate independently of the serial communication between the master and selected slave. (d) Acknowledge signal (ACK) control function The acknowledge signal is controlled so that confirmation can be made that serial data has been received. (e) Busy signal (BUSY) control function The busy signal is controlled so that the master is notified of the busy status of a slave. 236 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (2) Definition of SBI This paragraph describes the format of the serial data in the SBI mode and the meanings of the signals used. The serial data transferred in the SBI mode are classified into “address”, “command”, and “data”. Figure 5-71. SBI Transfer Timings Address transfer 8 9 SCK SB0, SB1 Bus release signal Command transfer SCK A7 A0 ACK BUSY Command signal 9 SB0, SB1 C7 C0 ACK BUSY READY Data transfer SCK 8 9 SB0, SB1 D7 D0 ACK BUSY READY The bus release and command signals are output by the master. BUSY is output by the slave. ACK can be output by both the master and slave (usually, this signal is output by the receiver of 8-bit data). The master continues outputting the serial clock since the start of 8-bit data transfer until the BUSY signal is deasserted. 237 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (a) Bus release signal (REL) The bus release signal is asserted when the SB0 or SB1 line goes high while the SCK line is high (i.e., when the serial clock is not output). This signal is output by the master. Figure 5-72. Bus Release Signal SCK SB0, SB1 “H” The bus release signal indicates that the master is to transmit an address to a slave. The slave has hardware that detects the bus release signal. Caution The transition of the SB0 or SB1 line from low level to high level when the SCK line is high is interpreted as a bus release signal. Therefore, if the transition timing of the bus is shifted due to the influence of the board capacitance, this may be interpreted as a bus release signal regardless of whether or not data are transmitted. Take precautions in wiring so that noise is not applied to the signal line. (b) Command signal (CMD) The command signal is asserted when the SB0 or SB1 line goes low while the SCK line is high (i.e., when the serial clock is not output). This signal is output by the master. Figure 5-73. Command Signal SCK SB0, SB1 “H” The slave has hardware that detects the command signal. Caution The transition of the SB0 or SB1 line from high level to low level when the SCK line is high is interpreted as a command signal. Therefore, if the transition timing of the bus is shifted due to the influence of the board capacitance, this may be interpreted as a command signal regardless of whether or not data are transmitted. precautions in wiring so that noise is not applied to the signal line. Take 238 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (c) Address An address is 8-bit data output by the master to select a specific slave from the slaves connected to the bus line. Figure 5-74. Address SCK SB0, SB1 1 A7 2 A6 3 A5 4 A4 5 A3 6 A2 7 A1 8 A0                      Address Bus release signal Command signal The 8-bit data following the bus release signal and command signal is defined as an address. The slave detects an address by using hardware, and checks whether the 8-bit data coincides with its own specification number (slave address). If the 8-bit data coincides with the slave address, the slave is selected. After that, the slave communicates with the master, until the master later unselects the slave. Figure 5-75. Selecting Slave by Address Master Slave 1 Unselected Slave 2 Selected Slave 3 Unselected Slave 4 Unselected 239 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (d) Command and data The master transmits commands to or transmits data to or receives data from the slave it has selected by transmitting an address. Figure 5-76. Command SCK SB0, SB1 1 C7 2 C6 3 C5 4 C4 5 C3 6 C2 7 C1 8 C0                      Command signal Command Figure 5-77. Data 1 D7 2 D6 3 D5 4 D4 5 D3 6 D2 7 D1 8 D0 SCK SB0, SB1 8-bit data following a command signal is defined as a command. 8-bit data that does not follow a command signal is defined as data. How to use commands and data can be determined arbitrarily, depending on the communication specifications.                      Data 240 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (e) Acknowledge signal (ACK) The acknowledge signal is used for confirmation of data reception between the transmitter and receiver. Figure 5-78. Acknowledge Signal (When output in synchronization with 11th SCK) SCK 8 9 10 11 SB0, SB1 ACK (When output in synchronization with 9th SCK) SCK 8 9 SB0, SB1 ACK The acknowledge signal is a one-shot pulse synchronized with the falling edge of SCK after 8-bit data has been transferred, and can be synchronized with arbitrary assertion of SCK. The transmitter side checks, after it has transmitted 8-bit data, whether the receiver side returns an acknowledge signal. If the acknowledge signal is not returned in a fixed time period after the data has been transmitted, it is judged that the data has not been received correctly. 241 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (f) Busy (BUSY) and ready (READY) signals A busy signal is output by a slave to inform the master that the slave is preparing for transmission or reception. A ready signal is also output by a slave to inform the master that the slave is now ready for transmission or reception. Figure 5-79. Busy and Ready Signals SCK 8 9 SB0, SB1 ACK BUSY READY In the SBI mode, the slave makes the SB0 (or SB1) line low to inform the master of the busy status. The busy signal is output following the acknowledge signal output by the master or slave. The busy signal is asserted or deasserted in synchronization with the falling edge of SCK. The master automatically ends output of serial clock SCK when the busy signal is deasserted. The master can start the next transfer when the busy signal has been deasserted and the ready signal is asserted. 242 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (3) Register setting When the SBI mode is used, the following two registers must be set: • Serial operation mode register (CSIM) • Serial bus interface control register (SBIC) (a) Serial operation mode register (CSIM) When the SBI mode is used, set the CSIM as shown below (For the format of the CSIM, refer to 5.6.3 (1) Serial operation mode register (CSIM)). The CSIM is manipulated by using 8-bit manipulation instructions. Bits 7, 6, and 5 can also be manipulated in 1-bit units. The contents of the CSIM are cleared to 00H at reset. The shaded portion in the figure indicates the bits used in SBI mode. Address FE0H Symbol CSIM 7 CSIE 6 COI 5 4 3 2 1 0 WUP CSIM4 CSIM3 CSIM2 CSIM1 CSIM0 Serial clock select bits (W) Serial interface operation mode select bits (W) Wake-up function specification bit (W) Coincidence signal from address comparator (R) Serial interface operation enable/disable bit (W) Remark (R) : read only (W): write only Serial interface operation enable/disable bit (W) Operation of Shift Register CSIE 1 Shift operation range Serial Clock Counter Count operation IRQCSI Flag Can be set SO/SB0 or SI/SB1 Pin Function in each mode and port 0 function shared Signal from address comparator (R) COI Note Clear Condition (COI = 0) When slave address register (SVA) data and shift register data do not coincide Set Condition (COI = 1) When slave address register (SVA) data and shift register data coincide Note COI can be read before the start of serial transfer and after the completion of serial transfer. An undefined value is read if this bit is read during transfer. Data written to COI by an 8-bit manipulation instruction is ignored. 243 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Wake-up function specification bit (W) WUP 0 1 Sets IRQCSI each time a serial transfer is completed with SBI mode masked Used only by the slave in SBI mode. Only when the address received by the slave after the bus has been released coincides with the data in the slave register of the slave (wake-up status), IRQCSI is set. SB0 or SB1 goes into a high-impedance state. Caution BUSY is not deasserted if WUP is set to 1 while the BUSY signal is output. In the SBI mode, after a command to deassert the BUSY signal has been issued, the BUSY signal is output until the next serial clock (SCK) falls. Before setting WUP to 1, be sure to deassert the BUSY signal and confirm that the SB0 (or SB1) pin has gone high. Serial interface operation mode select bit (W) CSIM4 0 1 CSIM3 1 CSIM2 0 Bit Order of Shift Register SIO7-0 ↔ XA (MSB first) SB0/P02 Pin Function SB0 (N-ch open-drain I/O) P02 (CMOS input) SB1/P03 Pin Function P03 (CMOS input) SB1 (N-ch open-drain I/O) Serial clock select bit (W) CSIM1 0 0 1 1 CSIM0 0 1 0 1 Serial Clock External clock input to SCK pin Timer/event counter output (TOUT0) f X/24 (262 kHz)Note SCK Pin Mode Input Output f X/23 (524 kHz)Note Note The frequency in parentheses applies when f X = 4.19-MHz operation. 244 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (b) Serial bus interface control register (SBIC) When the SBI mode is used, set SBIC as shown below (for the format of SBIC, refer to 5.6.3 (2) Serial bus interface control register (SBIC)). This register is manipulated by using bit manipulation instructions. The contents of SBIC are cleared to 00H at reset. The shaded portion in the figure indicates the used bits in the SBI mode. Address FE2H Symbol SBIC 7 6 5 4 3 2 1 0 BSYE ACKD ACKE ACKT CMDD RELD CMDT RELT Bus release trigger bit (W) Command trigger bit (W) Bus release detection flag (R) Command detection flag (R) Acknowledge trigger bit (W) Acknowledge enable bit (R/W) Acknowledge detection flag (R) Busy enable bit (R/W) Remark (R) : read only (W) : write only (RW) : read/write Busy enable bit (R/W) BSYE 0 Disables automatic output of busy signal Stops output of busy signal in synchronization with falling edge of SCK immediately after clear instruction has been executed Following acknowledge signal, busy signal is output in synchronization with falling edge of SCK 1 Acknowledge detection flag (R) ACKD Clear Condition (ACKD = 0) At start of transfer At reset input Set Condition (ACKD = 1) When acknowledge signal (ACK) is detected (synchronized with rising edge of SCK) Acknowledge enable bit (R/W) ACKE 0 1 Disables automatic output of acknowledge signal (output by ACKT is enabled) When set before end of transfer When set after end of transfer ACK is output in synchronization with 9th SCK ACK is output in synchronization with SCK immediately after execution of set instruction 245 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Acknowledge trigger bit (W) ACKT If this bit is set after end of transfer, ACK is output in synchronization with next SCK. This bit is automatically cleared to 0 after ACK signal has been output. Cautions 1. Do not set this bit to 1 before the end of serial transfer or during transfer. 2. ACKT cannot be cleared by software. 3. To set ACKT, clear ACKE to 0. Command detection flag (R) CMDD Clear Condition (CMDD = 0) When transfer start instruction is executed When bus release signal (REL) is detected When reset signal is input CSIE = 0 (Refer to Figure 5-60.) Set Condition (CMDD = 1) When command signal (CMD) is detected Bus release detection flag (R) RELD Clear Condition (RELD = 0) When transfer start instruction is executed When reset signal is input CSIE = 0 (Refer to Figure 5-60.) When SVA and SIO do not coincide at time address is received Set Condition (RELD = 1) When bus release signal (REL) is detected Command trigger bit (W) CMDT This bit controls output trigger of command signal (CMD). When this bit is set to 1, SO latch is cleared to 0. After that, the CMDT bit is automatically cleared to 0. Caution Do not set SB0 (or SB1) during serial transfer. Be sure to set it before the start of or after the end of transfer. Bus release trigger bit (W) RELT This bit controls output trigger of bus release signal (REL). When this bit is set to 1, SO latch is set to 1. After that, the RELT bit is automatically cleared to 0. Caution Do not set SB0 (or SB1) during serial transfer. Be sure to set it before the start of or after the end of transfer. 246 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (4) Selecting the serial clock The serial clock is selected by using the bits 0 and 1 of the serial operation mode register (CSIM). The following four types of serial clocks can be selected: Table 5-11. Selection of Serial Clock and Applications (in SBI mode) Mode Register CSIM1 0 0 1 1 CSIM0 0 1 0 1 Source External SCK TOUT F/F fX/2 4 fX/2 3 Serial Clock Timing at Which Shift Register Can Be Read/ Masking Serial Clock Written and Serial Transfer Can Be Started In operation enable mode (CSIE = 1) If serial clock is masked after 8-bit serial transfer When SCK is high Application Slave CPU Serial transfer at any speed Medium-speed serial transfer High-speed serial transfer Automatically masked at end of transfer of 8-bit data When the internal system clock is selected, SCK is internally stopped when SCK has been asserted and deasserted eight times. Externally, however, counting SCK continues until the slave enters the ready status. 247 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (5) Signals Figures 5-80 through 5-85 illustrate the operation of the signals in the SBI mode. Table 5-12 lists the signals used in the SBI mode. Figure 5-80. RELT, CMDT, RELD, CMDD Operation (master) Transfer start indication SIO SCK "H" SO latch RELT CMDT RELD CMDD Figure 5-81. RELT, CMDT, RELD, CMDD Operation (slave) Transfer start indication SIO latch SIO SCK 1 2 7 8 SO latch RELT (Master) CMDT (Master) D7 D6 D1 D0 When address match is found RELD When no address match is found CMDD Figure 5-82. ACKT Operation Set after transfer is complete SCK 6 7 8 9 ACK signal is output during one clock period immediately after set SB0, SB1 ACKT D2 D1 D0 ACK When set during this period Caution Do not set ACKT before transfer terminates. 248 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-83. ACKE Operation (a) When ACKE = 1 when transfer is complete SCK 1 2 7 8 9 SB0, SB1 D7 D6 D2 D1 D0 ACK ACK signal is output on the ninth clock cycle. ACKE When ACKE = 1 at this point of time. (b) When set after transfer is complete SCK 6 7 8 9 SB0, SB1 D2 D1 D0 ACK ACK signal is output during one clock period immediately after set. ACKE When set during this period and ACKE = 1 on the next SCK falling edge (c) When ACKE = 0 when transfer is complete SCK 1 2 7 8 9 SB0, SB1 D7 D6 D2 D1 D0 ACK signal is not output. ACKE When ACKE = 0 at this point of time (d) When the period during which ACKE = 1 is short SCK SB0, SB1 ACK signal is not output ACKE When ACKE is set and reset during this period and remains reset to 0 on the SCK falling edge 249 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-84. ACKD Operation (a) When ACK signal is output during the period of the ninth SCK clock Transfer start indication SIO Transfer start SCK 6 7 8 9 SB0, SB1 D2 D1 D0 ACK ACKD (b) When ACK signal is output after the ninth SCK clock Transfer start indication SIO Transfer start SCK 6 7 8 9 SB0, SB1 D2 D1 D0 ACK ACKD (c) Reset timing when transfer start indication is given during BUSY Transfer start indication SIO Transfer start SCK 6 7 8 9 SB0, SB1 D2 D1 D0 ACK BUSY D7 D6 ACKD Figure 5-85. BSYE Operation SCK 6 7 8 9 SB0, SB1 ACK BUSY BSYE When BSYE = 1 at this point of time When reset during this period and BSYE = 0 on the SCK falling edge 250 Table 5-12. Signal in SBI Mode (1/2) Signal Name Bus release signal (REL) Output Device Master Definition SB0, SB1 rising edge when SCK = 1 Timing Chart Output Conditions • Set RELT Flag Influence • Set RELD • Clear CMDD Explanation When this signal is followed by CMD signal output, it indicates that transmit data is address. (i) After REL signal is output, transmit data is address. (ii) REL signal is not output. Transmit data is command. Completion of reception. SCK SB0, SB1 “H” Command signal (CMD) Master SB0, SB1 falling edge when SCK = 1 • Set CMDT SCK SB0, SB1 “H” • Set CMDD CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Acknowledge signal (ACK) Master/ slave Low signal output to SB0, SB1 during the period of one clock SCK after completion of serial reception [Synchronous busy signal] Low-level output to SB0, SB1 following acknowledge signal High-level output to SB0, SB1 before start or after completion of serial transfer [Synchronous busy signal] SCK 9 ACK SB0, SB1 D0 ACK SB0, SB1 D0 BUSY READY BUSY READY ACKE = 1 ACKT set • Set ACKD Busy signal (BUSY) Slave • BSYE = 1 — Serial reception cannot be done because processing is being performed. Serial reception is enabled. Ready signal (READY) Slave BSYE = 0 Execution of SIO data write instruction (transfer start indication) — 251 252 Signal Name Serial clock (SCK) Output Device Master Definition Synchronizing clock for output of address, command, data, ACK signal, synchronous BUSY signal, etc. Address, command, or data is transferred on the first eight. Address (A7 to A0) Master 8-bit data transferred in synchronization with SCK after REL and CMD signals are output. 8-bit data transferred in synchronization with SCK after only CMD signal is output without REL signal output. Data (D7 to D0) Master or slave 8-bit data transferred in synchronization with SCK when neither REL nor CMD signal is output. Command (C7 to C0) Master Table 5-12. Signal in SBI Mode (2/2) Timing Chart Output Conditions Execution of 8 9 10 Flag Influence IRQCSI is set (on the rising edge of ninth clock)Note 1 Explanation Signal output timing to serial data bus SCK 1 2 7 SB0, SB1 data write instruction into SIO when CSIE = 1 (serial transfer start indication)Note 2 CHAPTER 5 SCK 1 2 7 8 Slave device address value on serial bus PERIPHERAL HARDWARE FUNCTION SB0, SB1 REL CMD SCK 1 2 7 8 Indication, message to slave device SB0, SB1 CMD SCK 1 2 7 8 Data processed by slave or master SB0, SB1 Notes 1. When WUP = 0, IRQCSI is always set on the rising edge of the ninth SCK clock. When WUP = 1, IRQCSI is set on the rising edge of the ninth SCK clock only when address is received and matches the value in the slave address register (SVA). 2. In the BUSY state for the data transmission and reception (transfer), transfer is started after the READY state is entered. CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (6) Pin configuration The configurations of the serial clock pin (SCK) and serial data bus pin (SB0 or SB1) are as follows: (a) SCK ··················· Inputs or outputs serial clock Master ······ CMOS, push-pull output Slave ········ Schmitt input (b) SB0, SB1 ·········· Serial data I/O pin N-ch open-drain output and Schmitt input for both master and slave Because the serial data bus line is of the N-ch open-drain output configuration, an external pull-up resistor must be connected to it. Figure 5-86. Pin Configuration Slave device Master device (Clock output) Clock input Serial clock (Clock input) SCK Clock output SCK N-ch open-drain SO SB0, SB1 RL Serial data bus SB0, SB1 N-ch open-drain SO SI SI Caution Because it is necessary to turn off the N-ch transistor when data is received, write FFH to SIO in advance. The transistor can be always turned off during transfer. However, if the wake-up function specification bit (WUP) = 1, the N-ch transistor is always off. Therefore, it is not necessary to write FFH to SIO before reception. 253 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (7) Detection of address coincidence In the SBI mode, the master transmits an address to select a specific slave and then starts communicating with the selected slave. Whether the address transmitted to a slave coincides with the address of the slave is detected by the hardware of the slave. For this purpose, the slave is provided with a slave address register (SVA). In the wake-up status (WUP = 1), the slave sets IRQCSI only when the address transmitted from the master coincides with the value set in the SVA of the slave. Cautions 1. Whether a slave is selected or not is detected by observing if there is a coincidence between the address transmitted from the master and the slave address of the slave after the bus has been released (RELD = 1). For this coincidence detection, an address coincidence interrupt (IRQCSI) that is generated when WUP = 1 is usually used. Therefore, detect whether a slave is selected or not when WUP = 1. 2. To detect whether the slave is selected when WUP = 0 and without using an interrupt, do not detect the address coincidence, but transmit and receive a command determined by the program in advance. (8) Error detection In the SBI mode, because the status of the serial bus SB0 or SB1 during transmission is also loaded to the shift register SIO of the device transmitting data, an error can be detected by the following methods: (a) By comparing SIO data before and after transmission If the two data differ from each other, it can be assumed that a transmission error has occurred. (b) By using slave address register (SVA) The transmit data is placed in SIO and SVA and transmission is executed. After transmission, the COI bit (coincidence signal from the address comparator) of the serial operation mode register (CSIM) is tested. If this bit is “1”, the transmission has been completed normally. If it is “0”, it can be assumed that a transmission error has occurred. (9) Communication operation In the SBI mode, the master usually selects one of the slave devices with which it is to communicate, by outputting an “address” onto the serial bus. After the master has selected the slave device, commands and data are transmitted and received between the master and slave. In this way, serial communication is implemented. Figures 5-87 through 5-90 show the timing charts illustrating each kind of data communication. In the SBI mode, the shift register performs shift operations in synchronization with the falling edge of the serial clock (SCK), and the transmit data is latched to the SO latch and output from the SB0/P02 or SB1/P03 pin with the MSB first. The receive data input to the SB0 (or SB1) pin at the rising edge of SCK is latched to the shift register. 254 Figure 5-87. Address Transmission Operation from Master Device to Slave Device (when WUP = 1)
 ,
,   
,  
,  

,  
, 
,  ,  Serial transmission operation IRQCSI generation 1 2 3 4 5 6 7 8 9 A7 A6 A5 A4 A3 A2 A1 A0 Address WUP ← 0 Serial receiving operation IRQCSI generation Master device processing (transmitting party) Program processing CMDT RELT CMDT Write into set set set SIO Interrupt processing (preparation for the next serial transfer) Hardware operation ACKD set SCK stop CHAPTER 5 Transfer line SCK pin PERIPHERAL HARDWARE FUNCTION SB0, SB1 pin ACK BUSY READY Slave device processing (receiving party) Program processing Hardware operation
 ,  
,
,  
 
,
,
,   ,
,  
, 
 
,  ,
,   
,  
 
, ,  
,  ACKT set BUSY clear CMDD CMDD CMDD set clear set RELD set ACK BUSY output output BUSY clear (when SVA = SIO) 255  
 
, ,  
, 
,  
,  
,
,  
 256 Master device processing (transmitting party) Program processing Hardware operation Transfer line SCK pin SB0, SB1 pin Slave device processing (receiving party) Program processing Hardware operation Figure 5-88. Command Transmission Operation from Master Device to Slave Device CMDT Write into SIO set Interrupt processing (preparation for the next serial transfer) Serial transmission operation IRQCSI generation ACKD set SCK stop CHAPTER 5 1 2 3 4 5 6 7 8 9 PERIPHERAL HARDWARE FUNCTION C7 C6 C5 C4 C3 C2 C1 C0 ACK BUSY READY    
, ,  
 
,  ,  
 
,
,  
, 
,  ,  
,
,  
 
,  ,  
,  , Command SIO read Command interpretation ACKT set BUSY clear CMDD set Serial receiving operation IRQCSI generation ACK BUSY output output BUSY clear Figure 5-89. Data Transmission Operation from Master Device to Slave Device
 
 
,  ,
,  
,   
,  
,
,   , Write into SIO Serial transmission operation IRQCSI generation Master device processing (transmitting party) Program processing Interrupt processing (preparation for the next serial transfer) Hardware operation ACKD set SCK stop CHAPTER 5 Transfer line SCK pin 1 2 3 4 5 6 7 8 9 PERIPHERAL HARDWARE FUNCTION SB0, SB1 pin D7 D6 D5 D4 D3 D2 D1 D0 ACK BUSY READY Slave device processing (receiving party) Program processing Hardware operation  
 
,
,  
,  
,  , 
,  
 
,  ,  
,
,   
 
,
,  
, 
,  
,  
, Data SIO read ACKT set BUSY clear Serial receiving operation IRQCSI generation ACK BUSY output output BUSY clear 257 
,  
, 
,  ,  
,
,  
 
,  , 
,  
,  
  , Figure 5-90. Data Transmission Operation from Slave Device to Master Device Write FFH into SIO SIO read SCK stop Serial receiving operation IRQCSI generation 258 Transfer line Master device processing (receiving party) Program processing ACKT Write FFH into SIO set Receive data processing Hardware operation ACK output Serial receiving operation CHAPTER 5 SCK pin 1 2 3 4 5 6 7 8 9 1 2 PERIPHERAL HARDWARE FUNCTION SB0, SB1 pin BUSY READY D7 D6 D5 D4 Data D3 D2 D1 D0 ACK BUSY READY D7 D6 Slave device processing (transmitting party) Program processing Hardware operation
,  
 
, ,  
, 
,  ,  
,
, 
 
,   ,  
, 
,  
,  

,  
, 
,    , Write into SIO Write into SIO BUSY clear Serial transmission operation IRQCSI generation ACKD BUSY BUSY set output clear CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (10) Starting transfer Serial transfer is started when the transfer data is placed in the shift register (SIO), if the following two conditions are satisfied: • Serial interface operation enable/disable bit (CSIE) = 1 • The internal serial clock is stopped after 8-bit serial transfer or SCK is high Cautions 1. Transfer is not started even if CSIE is set to “1” after the data has been written to the shift register. 2. Because it is necessary to turn off the N-ch transistor when data is received, write FFH to SIO in advance. When the wake-up function specification bit (WUP) = 1, however, it is not necessary to write FFH to SIO, because the N-ch transistor is always off. 3. If data is written to SIO while the slave is busy, the data is not lost. When the SB0 (or SB1) input goes high and the slave becomes ready after the slave has been released from the busy status, transfer is started. When an 8-bit transfer has been completed, the serial transfer is automatically stopped, and an interrupt request flag (IRQCSI) is set. Example To transfer the RAM data addressed by the HL register and at the same time, load the SIO data in the accumulator, and start serial transfer MOV SEL XCH XA, @HL MB15 XA, SIO ; Takes out transmit data from RAM ; or CLR1 MBE ; Exchanges transmit data and receive data, and starts transfer 259 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (11) Notes on SBI mode (a) Whether a slave is selected or not is detected by observing if there is a coincidence between an address transmitted from the master after the bus has been released (RELD = 1) and the slave address of the slave. For this coincidence detection, an address coincidence interrupt (IRQCSI) that is generated when WUP = 1 is usually used. Therefore, detect whether a slave is selected or not by using the slave address when WUP = 1. (b) To detect whether a slave is selected or not when WUP = 0 without using the interrupt, do not detect address coincidence, but transmit or receive a command set in advance by program. (c) If WUP is set to 1 while the BUSY signal is output, the BUSY signal is not deasserted. In the SBI mode, the BUSY signal is output until the next serial clock (SCK) falls after a command that deassert the BUSY signal has been issued. Before setting WUP to 1, be sure to deassert the BUSY signal and confirm that the SB0 (or SB1) pin has gone high. 260 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (12) Application of SBI mode This paragraph introduces an application example in which serial data communication is executed in the SBI mode. In this example, the µPD753108 can operate as both the master and slave CPU on the serial bus. Moreover, the master can be changed by a command. (a) Serial bus configuration In the application example presented below, it is assumed that the µ PD753108 is connected to the bus line as one of the devices in the serial bus. The µ PD753108 uses the serial data bus SB0 (or SB1) and serial clock SCK pins. Figure 5-91 shows an example of serial bus configuration. Figure 5-91. Example of Serial Bus Configuration VDD Master CPU µ PD753108 Slave CPU µ PD753108 SB0, SB1 SB0, SB1 Address 1 SCK SCK Slave CPU SB0, SB1 Address 2 SCK Slave IC SB0, SB1 Address N SCK 261 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (b) Command description In this application example, the following commands are used: READ WRITE END STOP RESET : Transfers data from slave to master : Transfers data from master to slave : Notifies slave of end of WRITE command : Notifies slave that WRITE command has been aborted : Unselects slave currently selected STATUS : Reads status of slave CHGMST : Relinquishes mastership to slave Communication between the master and a slave is carried out in the following procedure: The master transmits the address of a slave with which the master is to communicate, to select the slave (chip select). The slave that has received the address returns ACK to start communication with the master (the slave is selected). Commands and data are transmitted between the master and the slave selected in . Note that the other slaves must be unselected, because commands and data are transmitted between the master and a slave on a one-to-one basis. Communication ends when the slave is unselected. The slave is unselected in the following cases: • When the master transmits the RESET command, the selected slave is unselected. • When the master is changed to a slave by the CHGMST command, the device changed to a slave is unselected. 262 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Here is the transfer format of each command: READ command This command reads data from a slave. The number of data to be read varies from 1 to 256 bytes. The master specifies the number of data as a parameter. If 00H is specified as the number of data, 256 bytes of data is transferred. Figure 5-92. Transfer Format of READ Command M READ Command S ACK M Number of data Data S ACK S Data 0 Data S ACK ····· S Data N Data S ACK Remark M : output by master S : output by slave If the slave has more data than the number of data it has received, the slave returns ACK; if not, the slave does not return ACK, and an error occurs. The master sends ACK to the slave each time it receives 1 byte. 263 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION WRITE, END, and STOP commands The WRITE command writes data to a slave. The number of data to be written is variable from 1 to 256 bytes. The master specifies the number of data as a parameter. If 00H is specified as the number of data, data of 256 bytes is transferred. Figure 5-93. Transfer Formats of WRITE and END Commands M WRITE Command S ACK M Number of data Data S ACK M Data 0 Data S ACK ····· M Data N Data S ACK M END Command S ACK Remark M : output by master S : output by slave The slave returns ACK after it has received the number of data, if it has an enough area to store the received data. If the area runs short, the slave does not return ACK, and an error occurs. The master sends the END command after it has transferred all the data. This command notifies the slave that all the data have been correctly transferred. The slave receives the END command even before all the data have been received. In this case, the data which has been received immediately before receiving the END command is valid. The master compares the contents of SIO before and after transfer to check to see if the data have been correctly output onto the bus. If the contents of SIO before and after transfer differ, the master sends the STOP command to stop data transfer. Figure 5-94. Transfer Format of STOP Command M Data Data S ACK M STOP Command Checks data. Error occurs. Stops data transfer. S ACK Remark M : output by master S : output by slave When the slave receives the STOP command, it invalidates 1-byte of the data received immediately before reception of the STOP command. 264 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION STATUS command This command reads the status of the slave currently selected. Figure 5-95. Transfer Format of STATUS Command M STATUS Data S ACK S Status Command S ACK Remark M : output by master S : output by slave The format of the status returned by the slave is as follows: Figure 5-96. Status Format of STATUS Command MSB Status 7 6 5 4 3 2 1 LSB 0 Bit indicating whether slave has data to transfer 0: Slave has no data to transfer 1: Slave has data of 1 byte or more to transfer Bit indicating whether slave is ready to receive data 0: Slave does not have enough area to store received data 1: Slave has area of 1 byte or more to store received data Bit indicating occurrence of error 0: No error 1: Error occurs during previous transfer Bit indicating whether master can be changed 0: Master cannot be changed 1: Master can be changed The master returns ACK to slave when it has received the data of status.          All 0 265 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION RESET command This command unselects the slave currently selected. By sending the RESET command, the master can unselect all the slaves. Figure 5-97. Transfer Format of RESET Command M RESET Command S ACK Remark M : output by master S : output by slave CHGMST command This command gives the mastership to the slave currently selected. Figure 5-98. Transfer Format of CHGMST Command M CHGMST Command S ACK M DATA Data S ACK Remark M : output by master S : output by slave When the slave has received the CHGMST command, it decides whether it can receive mastership, and returns the following data to the master: • FFH: Master can be changed • 00H: Master cannot be changed The slave compares the contents of SIO before and after transfer of data. If the SIO contents do not coincide, the slave does not return ACK, and an error occurs. The master returns ACK when it has received data. If the received data is FFH, the master starts operating as a slave. After the slave has sent data FFH and received ACK from the master, it starts operating as a master. 266 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION An error may occur during communication between the master and a slave. If an error occurs, the slave notifies the master of error occurrence by not returning ACK to the master. If an error occurs only when the slave receives data, the slave sets the bit of the status that indicates occurrence of an error and cancels the processing of all the commands under execution. The master checks whether the slave has returned ACK after it has completed transfer of 1 byte. If the slave does not return ACK in specific time after the master has completed transfer, the master judges that an error has occurred, and outputs a dummy ACK signal. Figure 5-99. Operations of Master and Slave in Case of Error Processing by slave Reception completed. Error occurs. Slave stops processing. SB0, SB1 Error data ACK ACK wait time Processing by master Master checks whether ACK is returned from slave. Transfer completed. Master starts checking ACK. Error occurs. Master outputs ACK. The following types of errors may occur: • Error occurs in slave If the transfer format of a command is wrong If an undefined command is received If the number of data to be transferred by the slave runs short when READ command is executed If the slave does not have an enough area to store data when the WRITE command is executed If the data transferred by the READ, STATUS, or CHGMST command changes If any of the above occurs, the slave does not return ACK. • Error occurs in master When the data to be transferred by the master changes when the WRITE command is executed, the master sends the STOP command to the slave. 267 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.6.8 SCK pin output manipulation The SCK/P01 pin, which incorporates an output latch, can also produce static output by software control in addition to a normal serial clock. The number of SCKs can be set as desired by using software to control the P01 output latch (the SO/SB0/P02, and SI/SB1/P03 pins are controlled by setting the SBIC RELT and CMDT bits). The SCK/P01 pin output control method is described below: The serial operation mode register (CSIM) is set (SCK pin: output mode). SCK from serial clock control circuit is set to 1 during serial transfer stop. The P01 output latch is controlled by using bit manipulation instructions. Example To output one clock pulse to SCK/P01 pin by using software. SEL MOV MOV CLR1 SET1 MB15 CSIM, XA 0FF0H.1 0FF0H.1 ; SCK/P01 ← 0 ; SCK/P01 ← 1 ; or CLR1 MBE XA, #10000011B ; SCK (f X/2 3 ), output mode Figure 5-100. SCK/P01 Pin Configuration Address FF0H.1 P01/SCK To internal circuit P01 output latch SCK SCK pin output mode From serial clock control circuit The P01 output latch is mapped in bit 1 of address FF0H. When the RESET signal is generated, the P01 output latch is set to 1. Cautions 1. The P01 output latch must be set to 1 during normal serial transfer. 2. Do not use “PORT0.1” to specify the P01 output latch address. Write directly the address (0FF0H.1) in operand or specify SCKP. At that time, set MBE to 0, or set MBE to 1 and MBS to 15 in advance. Do not use CLR1 SET1 PORT0.1 PORT0.1 Use CLR1 SET1 CLR1 SET1 0FF0H.1 0FF0H.1 SCKP SCKP 268 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.7 5.7.1 LCD Controller/Driver LCD controller/driver configuration The µ PD753108 incorporates a display controller which generates segment and common signals according to the display data memory contents and incorporates segment and common drivers which can drive the LCD panel directly. Figure 5-101 shows the LCD controller/driver configuration. 269 270 4 4 Port 8 output latch 3210 4 4 8 4 LCD/port selection register Port 9 Port mode output latch register group C 3210 0 1 Decoder Port 8 Input/Output buffer 01 2 3 Port 9 Input/Output buffer 01 2 3 Figure 5-101. LCD Controller/Driver Block Diagram Internal bus 4 1F7H 3210 1F0H 1EFH 1E0H Display mode register 3210 3210 3210 8 4 Display control register 4 Port 3 output latch 10 4 Port mode register group A 1 0 CHAPTER 5 3210 3210 3210 3210 Timing controller fLCD PERIPHERAL HARDWARE FUNCTION Segment driver Segment driver Common driver LCD drive voltage control LCD drive mode switch S23/P80 S16/P93 S15 S0 COM3 COM2 COM1 COM0 VLC2 VLC1 VLC0 P31/SYNC P30/LCDCL CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.7.2 LCD controller/driver functions The µ PD753108 LCD controller/driver functions are as follows: (a) Display data memory is read automatically by DMA operation and segment and common signals are generated. (b) Display mode can be selected from among the following five: Static 1/2 duty (time multiplexing by 2), 1/2 bias 1/3 duty (time multiplexing by 3), 1/2 bias 1/3 duty (time multiplexing by 3), 1/3 bias 1/4 duty (time multiplexing by 4), 1/3 bias (c) A frame frequency can be selected from among four in each display mode. (d) A maximum of 24 segment signal output pins (S0 to S23) and four common signal output pins (COM0 to COM3). (e) The segment signal output pins (S16 to S23) can be changed to the I/O ports (PORT8 and PORT9). (f) Split resistor can be incorporated to supply LCD drive power (mask option). • Various bias methods and LCD drive voltages can be applicable. • When display is off, current flowing through the split resistor is cut. (g) Display data memory not used for display can be used for normal data memory. (h) It can also operate by using the subsystem clock. Table 5-13 lists the maximum number of picture elements that can be displayed in each display mode. Table 5-13. Maximum Number of Displayed Picture Elements Bias Method Time Division — 1/2 Static 2 3 1/3 3 4 COM0, 1, 2, 3 96 (segment 24 × common 4) Note 4 Common Signals Used COM0 (COM1, 2, 3) COM0, 1 COM0, 1, 2 Maximum Number of Picture Elements 24 (segment 24 × common 1) Note 1 48 (segment 24 × common 2) Note 2 72 (segment 24 × common 3) Note 3 Notes 1. 3 digits (8 segment signals/digit) on LCD panel (display). 2. 6 digits (4 segment signals/digit) on LDC panel (display). 3. 8 digits (3 segment signals/digit) on LCD panel (display). 4. 12 digits (2 segment signals/digit) on LCD panel (display). 5.7.3 Display mode register (LCDM) The display mode register (LCDM) consists of eight bits to specify the display mode, LCD clock, frame frequency, and display output on/off control. LCDM is set by using an 8-bit memory manipulation instruction. Only bit 3 (LCDM3) can be set and cleared by using bit manipulation instructions. When the RESET signal is generated, all the bits are cleared to “0”. 271 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-102. Display Mode Register Format Address F8CH 7 0 6 0 5 4 3 2 1 0 Symbol LCDM LCDM5 LCDM4 LCDM3 LCDM2 LCDM1 LCDM0 LCD clock selection LCDM5 0 0 1 1 LCDM4 0 1 0 1 LCDCL Note fW /29 (64 Hz) f W /28 (128 Hz) f W /27 (256 Hz) f W /26 (512 Hz) Note LCDCL is supplied only when the watch timer operates. To use the LCD controller, bit 2 of watch mode register WM should be set to 1. Display mode selection LCDM3 0 1 1 1 1 1 LCDM2 × 0 0 0 0 1 LCDM1 × 0 0 1 1 0 LCDM0 × 0 1 0 1 0 Static Setting prohibited Time Division Value Display off Note 4 3 2 3 1/3 1/3 1/2 1/2 Bias Method Other than the above Note All segment signals are unselected. Frame frequency (Hz) LCDCL Display Duty Static 1/2 1/3 1/4 fW /29 (64 Hz) 64 32 21 16 f W/2 8 (128 Hz) 128 64 43 32 f W /27 (256 Hz) 256 128 85 64 f W/26 (512 Hz) 512 256 171 128 When fW = 32.768 kHz fW : Input clock to watch timer (fX/128 or fXT) 272 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.7.4 Display control register (LCDC) The display control register controls LCD drive as follows. • Enables/disables the common and segment outputs. • Cuts the current flowing through the split resistors for the LCD driving power supply. • Enables/disables synchronization clock (LCDCL) and synchronization signal (SYNC) outputs to the external segment signal extending controller/driver. • Switching of LCD drive modes (normal mode and low-voltage mode) by supply voltage Normal mode .............. Low current consumption. Low-voltage mode ...... For low voltage operation. Caution To drive LCD at V DD ≤ 2.2 V, be sure to set the low-voltage mode. The LCDC is set by a 4-bit memory manipulation instruction. When the RESET signal is generated, all the bits of the display control register are cleared to “0”. Figure 5-103. Format of Display Control Register Address F8EH 3 0 2 1 0 Symbol LCDC LCDC2 VAC0 LCDC0 Output enable/disable specification bit for LCDCL and SYNC signal LCDC2 0 1 Disables the output of LCDCL and SYNC signal. Enables the output of LCDCL and SYNC signal. Caution The LCDCL and SYNC signal are provided for system extension in the future. Currently, disable the signal output. LCD drive mode select bit VAC0 0 1 Normal mode (2.2 V ≤ VDD ≤ 5.5 V) Low-voltage mode (1.8 V ≤ V DD ≤ 5.5 V) 273 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Display output status by LCDC0 and LCDM3 LCDC0 LCDM3 COM0 to COM3 0 × Outputs “L” (display off). 0 Outputs a common signal corresponding to the display mode. Outputs a segment signal corresponding to the display mode (outputs an unselected level, display off). 1 1 Outputs a common signal corresponding to the display mode. Outputs a segment signal corresponding to the display mode (display on). S0 to S15 S16 to S23 segments specification pin S16 to S23 bit ports specification pin Power supply for the split resistors (BIAS pin output) Outputs “L” (display off). I/O ports. Whether the port is used as an input or output port depends on the specification of the port mode register group C (PMGC). Off (high-impedance)Note On (high-level)Note On (high-level)Note Note The descriptions in the parentheses apply to the case where the split resistors are not used. 274 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.7.5 LCD/port selection register (LPS) The LCD/port selection register (LPS) switches the segment signal output (S16 to S23) to the input/output port. Of segment signal outputs, S16 to S19 are also used as PORT9 and S20 to S23, as PORT8. Four outputs each are switched together as one unit. By setting the LPS value to “0000”, S16 to S23 can be switched to input/output ports (PORT9 and PORT8). The LPS bits are set by a 4-bit memory manipulation instruction. All LPS bits can be cleared to “0” by generating the RESET signal. Figure 5-104. LCD/Port Selection Register Format Address F8FH 3 0 2 LPS2 1 LPS1 0 LPS0 Symbol LPS Usable Pin Segment Output Pin 0 0 0 0 0 1 0 1 0 — S16 to S19 S16 to S19, S20 to S23 Port Pin P93 to P90, P83 to P80 P83 to P80 — Other than the above Setting prohibited Cautions 1. All LPS bits are cleared to “0” during resetting, and the LCD cannot be used. Be sure to set the LPS value to 0001 or 0010 when using the LCD. 2. Be sure to set bit 3 of LPS to “0”. 3. If the S16/P93 through S19/P90 and S20/P83 through S23/P80 pins are used as segment signal outputs, do not enable the on-chip pull-up resistors for these pins by software. If the port pins are specified as segment signal outputs by using LPS, they do not enter the floating state even if they are set to the input mode through the port mode register group C. This is why specifying on-chip pull-up resistor connection by software is unnecessary. When an input instruction is executed for the port specified as a segment signal output, the content of the output latch will be input. 275 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.7.6 Display data memory The display data memory is mapped in 1E0H to 1F7H. The display data memory is an area read by the LCD controller/driver, which performs DMA operation independently of CPU operation. The LCD controller controls the segment signals according to data in the display data memory. The area not used for LCD display or port can be used for normal data memory. The display data memory is manipulated in 1- or 4-bit units. It cannot be manipulated in 8-bit units. Figure 5-106 shows the relationship between the display data memory bits and segment output. Figure 5-105. Data Memory Map Data memory Memory bank 000H 256 × 4 0 0FFH 256 × 4 (224 × 4) 1 1E0H Display data memory (24 × 4) 1F7H 1F8H 1FFH (8 × 4) 276 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-106. Relationship between Display Data Memory and Common Segments b3 1E0H 1E1H 1E2H 1E3H b2 b1 b0 S0 S1 S2 S3 Display data memory 1F1H 1F2H 1F3H 1F4H 1F5H 1F6H 1F7H S17 S18 S19 S20 S21 S22 S23 COM3 COM2 COM1 COM0 Common signal Segment output 277 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.7.7 Common signal and segment signal The individual picture elements of the LCD panel light up when the potential difference between the corresponding common signal and segment signal is greater than a predetermined value (LCD driving voltage V LCD). When it goes lower than the V LCD or is zero, they go out. The LCD panel is degraded when a DC voltage is applied for the common signal and segment signal, therefore it is driven by an AC voltage. (1) Common signal The common signal is a selection timing in a sequence shown in Table 5-14 in accordance with the time division number which is set and repeats with that cycle. In the static mode, the same signal is output to the COM0 to COM3. When the time division number is 2, COM2 pin and COM3 pin must be open. When the time division number is 3, the COM3 pin must be open. Table 5-14. Common Signal Common Signal Time Division Number Static 2 3 4 Open Open Open COM0 COM1 COM2 COM3 (2) Segment signal There are 24 segment signals corresponding to the 24 locations in the display data memory (1E0H to 1F7H) of the data memory. Each location’s bits 0, 1, 2, and 3 are automatically read out in synchronization with the selection timings of COM0, COM1, COM2, and COM3, respectively. When the contents of each bit is 1, it is converted to the selection voltage; and if they are 0, it is converted to the non-selection voltage and then output via the segment pins (S0 to S23). As stated above, what combination of LCD panel’s front panel electrodes (corresponding to the segment signals) and rear panel electrodes (corresponding to the common signals) forms a display pattern on the display data memory must be checked and then the bit data which corresponds one-to-one to the pattern to be displayed must be written. Bits 1/2/3 in the display data memory in the static method, bits 2/3 in the division number 2 method, and bit 3 in the division number 3 are not accessed, therefore they can be used for purposes other than display. 278 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (3) Common and segment signal output waveforms Tables 5-15 to 5-17 list voltages output to the common and segment signals. +VLCD/–VLCD on voltage is applied only when both signals become selection voltages; otherwise, the off voltage is applied. Table 5-15. LCD Drive Voltage (Static) Segment Signal Sn Common Signal COM0 VSS/V LC0 Selection V LC0/V SS +VLCD/–V LCD Non-selection VSS/V LC0 0 V/0 V Table 5-16. LCD Drive Voltage (1/2 Bias method) Segment Signal Sn Common Signal COMm Selection Non-selection VSS/V LC0 +VLCD/–V LCD VLC1 = VLC2 + 1 1 VLCD/– VLCD 2 2 – 0 V/0 V 1 1 VLCD/+ VLCD 2 2 Selection V LC0/V SS Non-selection VSS/V LC0 Table 5-17. LCD Drive Voltage (1/3 Bias method) Segment Signal Sn Common Signal COMm Selection Non-selection VSS/V LC0 VLC1 /V LC2 Selection V LC0/V SS +VLCD/–V LCD + 1 1 VLCD/– VLCD 3 3 + + Non-selection VLC2 /VLC1 1 1 VLCD/– VLCD 3 3 1 1 VLCD/– VLCD 3 3 279 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figures 5-107 to 5-109 show the common signal waveforms. Figure 5-110 shows the common and segment signal electric potentials and phases. Figure 5-107. Common Signal Waveform (Static) VLC0 COM0 VLCD (Static) VSS TF = T T : One cycle of LCDCL TF : Frame cycle Figure 5-108. Common Signal Waveform (1/2 Bias method) VLC0 COMm (division by 2) TF = 2 × T VLC0 COMm (division by 3) TF = 3 × T T : One cycle of LCDCL TF : Frame cycle VLC1, 2 VSS VLCD VLC1, 2 VSS VLCD Figure 5-109. Common Signal Waveform (1/3 Bias method) VLC0 VLC1 VLCD COMm (division by 3) TF = 3 × T VLC0 VLC1 COMm (division by 4) TF = 4 × T T : One cycle of LCDCL TF : Frame cycle VLC2 VSS VLCD VLC2 VSS 280 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-110. Common and Segment Signal Electric Potentials and Phases (a) 1/3 bias method Selection Non-selection VLC0 Common signal VLC1 VLC2 VSS VSS VLC0 VLCD VLC1, 2 VSS T T VLCD VLCD (b) 1/2 bias method Selection Non-selection VLC0 VLC1, 2 VLCD VLC0 VLC1 Segment signal VLC2 VSS T T T : One cycle of LCDCL (c) Static display mode Selection Non-selection VLC0 Common signal VSS VLCD VLC0 Segment signal VSS T T VLCD 281 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.7.8 Supply of LCD drive power VLC0 , VLC1, and V LC2 In the µ PD753108, a split resistor can be incorporated in the VLC0 to V LC2 pins for the LCD drive power supply. According to the bias method, the LCD drive power can be supplied without an external split resistor. The µ PD753108 also includes the BIAS pin to deal with various LCD drive voltages. The BIAS and VLC0 pins are connected externally. Table 5-18 lists proper LCD drive power supply values based on the static, 1/2, and 1/3 bias methods. Table 5-18. LCD Drive Power Supply Values Bias Method LCD Drive Power VLC0 VLC1 VLC2 VSS No Bias (Static Mode) VLCD 2/3V LCD 1/3V LCD 0V 0V 1/2 V LCD 1/2VLCDNote 1/3 VLCD 2/3V LCD 1/3V LCD 0V Note When 1/2 bias is used, the VLC1 and VLC2 pins must be connected externally. Remark When the BIAS and VLC0 pins are not connected, V LCD = 3/5VDD (internal split resistor must be specified by using a mask option). When the BIAS and V LC0 pins are connected, V LCD = VDD. Figure 5-111, (a) to (c) show LCD drive power supply examples according to Table 5-18. Current flow through the split resistor can also be cut by clearing display control register bit 0 (LCDC0). This LCD power on/off control is also useful to prevent DC voltage from being applied to LCD (if the system clock subsystem is selected) when the LCD clock is stopped by execution of a STOP instruction, when the watch timer operates using the main system clock. That is, display control register bit 0 (LCDC0) is cleared and all LCD drive power sources are placed in the same potential VSS immediately before the STOP instruction is executed, thereby suppressing the potential difference between the LCD electrodes even if the LCD clock is stopped. When the watch timer operates by using the subsystem clock, the LCD display can be connected. 282 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-111. LCD Drive Power Connection Examples (when split resistor is incorporated) (a) 1/3 bias method and static display mode (In example V DD = 5 V, VLCD = 3 V) µPD753108 VDD (b) 1/2 bias method (In example V DD = 5 V, VLCD = 5 V) µPD753108 VDD LCDC0 BIAS pin 2R VLC0 R VLC1 VLCD VLC2 R VSS R LCDC0 BIAS pin 2R VLC0 R VLC1 VLCD VLC2 R VSS R VLCD = 3/5 VDD VLCD = VDD (c) 1/3 bias method and static display mode (In example VDD = 5 V, V LCD = 5 V) µPD753108 VDD LCDC0 BIAS pin 2R VLC0 R VLC1 VLCD VLC2 R VSS R VLCD = VDD 283 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-112. LCD Drive Power Connection Examples (when split resistor is connected externally) (a) Static display modeNote (In example V DD = 5 V, VLCD = 5 V) (b) Static display mode (In example V DD = 5 V, VLCD = 3 V) µPD753108 VDD µ PD753108 VDD LCDC0 BIAS pin LCDC0 BIAS pin 2R VLC0 VLC0 3R VLC1 VLC1 VLCD VLC2 VLC2 VLCD VSS VSS VLCD = VDD VLCD = 3/5 VDD (c) 1/2 bias method (In example V DD = 5 V, VLCD = 2.5 V) (d) 1/3 bias method (In example V DD = 5 V, VLCD = 3 V) µ PD753108 VDD µPD753108 VDD LCDC0 BIAS pin 2R VLC0 R VLC1 VLCD VLC2 R VSS LCDC0 BIAS pin 2R VLC0 R VLC1 VLCD VLC2 R VSS R VLCD = 1/2 VDD VLCD = 3/5 VDD Note Set LCDC0 always to 1 (including the case of standby mode). 284 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.7.9 Display mode (1) Static display example Figure 5-114 shows connection of a static 3-digit LCD panel having the display pattern shown in Figure 5-113, the µ PD753108 segment signals (S0 to S23), and the common signal (COM0). In this example, “12.3” is displayed. The contents of the display data memory (addresses 1E0H to 1F7H) correspond to the display pattern. Here, “2.” at the second digit position is taken as an example. It is necessary to output selection and nonselection voltages as shown in Table 5-19 to the S8 to S15 pins at the COM0 common signal timing according to the display pattern shown in Figure 5-113. Table 5-19. S16 to S23 Pin Selection and Non-selection Voltage (Static Display Example) Segment S8 Common COM0 Selection Non-selection Selection Selection Non-selection Selection Selection Selection S9 S10 S11 S12 S13 S14 S15 This shows that the bit 0 string of display data memory addresses 1E8H to 1EFH corresponding to S8 to S15 needs to be set to 10110111. Figure 5-115 shows the S11, S12, and COM0 LCD drive waveforms. This shows that alternating current square wave of +VLCD /–VLCD that is LCD on level is generated when S11 becomes the selection voltage at the selection timing of COM0. Since the same waveform as COM0 is output to COM1 to COM3, the drive capability can be increased by connecting COM0, COM1, COM2, and COM3. Figure 5-113. Static Mode LCD Display Pattern and Electrode Connection S3/S11/S19 S4/S12/S20 S2/S10/S18 S5/S13/S21 COM0 S6/S14/S22 S1/S9/S17 S0/S8/S16 S7/S15/S23 285 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-114. Static LCD Panel Connection Example µ PD753108 TIMING STROBE COM3 COM2 COM1 COM0 Can be shortened BIT0 BIT1 BIT2 BIT3 1E0H 1 2 3 4 5 6 7 DATA MEMORY ADDRESS 8 9 A B C D E F 1F0H 1 2 3 4 5 6 1F7H 0 S0 S1 S2 S3 S4 S5 S6 S7 S8 S10 S11 S12 S13 S14 S15 S16 S17 S18 S19 S20 S21 S22 S23 LCD PANEL S9 286 0 00 0 01 1 01 1 10 1 10 1 10 1 01 1 1 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-115. Static LCD Drive Waveform Example TF VLC0 COM0 VSS VLC0 S11 VSS VLC0 S12 VSS + VLCD COM0 to S11 0 – VLCD + VLCD COM0 to S12 0 – VLCD 287 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (2) Division by 2 display example Figure 5-117 shows connection of the division by 2 mode 6-digit LCD panel having the display pattern shown in Figure 5-116, the µPD753108 segment signals (S0 to S23), and the common signals (COM0 and COM1). In the example, “1234.56” is displayed. The contents of the display data memory (addresses 1E0H to 1F7H) correspond to the display pattern. Here, “3.” at the third digit position is taken as an example. It is necessary to output the selection and nonselection voltages as shown in Table 5-20 to the S12 to S15 pins at the timing of the COM0 and COM1 common signal according to the display pattern shown in Figure 5-116. Table 5-20. S12 to S15 Pin Selection and Non-selection Voltage (Division by 2 Display Example) Segment S12 Common COM0 COM1 Selection Non-selection Selection Selection Non-selection Non-selection Selection Selection S13 S14 S15 This shows that for example, the display data memory address 1EFH bits corresponding to S15 need to be set to ×× 10. Figure 5-118 shows an LCD drive waveform example among S15 and common signals. This shows an alternating current square wave of +V LCD/–VLCD that is the LCD on level being generated when S15 is the selection voltage at the COM1 selection timing. Figure 5-116. Division by 2 Mode LCD Display Pattern and Electrode Connection COM0 ,,, , Sn + 2 Sn + 3 Sn + 1 ,, ,,, , Sn COM1 288 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-117. Division by 2 LCD Panel Connection Example µ PD753108 TIMING STROBE COM3 COM2 COM1 COM0 OPEN OPEN 1E0H 1 2 3 4 5 6 7 DATA MEMORY ADDRESS 8 9 A B C D E F 1F0H 1 2 3 4 5 6 1F7H 1 0 S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 S11 S12 S13 S14 S15 S16 S17 S18 S19 S20 S21 S22 S23 LCD PANEL S10 0 0 ×: Any data can be stored at any time because of the division by 2 display. BIT0 BIT1 00 0 11 1 01 1 10 0 01 1 11 1 01 1 1 BIT2 01 1 10 1 00 0 11 0 11 1 01 0 11 1 0 BIT3 289 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-118. Division by 2 LCD Drive Waveform Example (1/2 Bias method) TF VLC0 COM0 VLC1, 2 VSS VLC0 COM1 VLC1, 2 VSS VLC0 S15 VLC1, 2 VSS +VLCD +1/2 VLCD COM0 to S15 0 –1/2 VLCD –VLCD +VLCD +1/2 VLCD COM1 to S15 0 –1/2 VLCD –VLCD 290 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (3) Division by 3 display example Figure 5-120 shows connection of a division by 3 mode 8-digit LCD panel having the display pattern shown in Figure 5-119, the µ PD753108 segment signals (S0 to S23), and the common signals (COM0 to COM2). In this example, “123456.78” is displayed. The contents of the display data memory (addresses 1E0H to 1F7H) correspond to the display pattern. Here, “6.” at the third digit position is taken as an example. It is necessary to output the selection and nonselection voltages as shown in Table 5-21 to the S6 to S8 pins at the COM0 to COM2 common signal timings according to the display pattern shown in Figure 5-119. Table 5-21. S6 to S8 Pin Selection and Non-selection Voltage (Division by 3 Display Example) Segment S6 Common COM0 COM1 COM2 Non-selection Selection Selection Selection Selection Selection Selection Selection — S7 S8 This shows that the bits at display data memory address 1E6H corresponding to S6 need to be set to ×110. Figure 5-121 (1/2 bias method) and 5-122 (1/3 bias method) show LCD drive waveforms among S6 and common signals. These show an alternating current square wave of +VLCD/–VLCD that is LCD on level being generated when S6 is the selection voltage at the COM1 selection timing and S6 is the selection voltage at the COM2 selection timing. Figure 5-119. Division by 3 Mode LCD Display Pattern and Electrode Connection Sn + 2   ,
,   Sn + 1 COM0 Sn COM1 COM2 291 292 DATA MEMORY ADDRESS TIMING STROBE D C E B A F 6 0 BIT0 BIT1 BIT2 BIT3 0 '0 0 0 0 0 0 1 0 0 '1 '1 '0 '1 '1 '0 '1 1 1 1 0 0 1 1 0 1 1 0 1 1 1 1 1 0 0 1 1 1 1 1 0 1 1 0 1 1 1 0 1 1 1 0 1 1 0 1 1 1 1 1 1 S9 S8 S7 S6 S5 S4 S3 S2 S1 S0 COM0 S22 LCD PANEL S21 5 4 3 2 1 9 8 7 6 5 4 3 2 1 1F7H 0 0 COM1 S23 1F0H 1E0 H µ PD753108 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-120. Division by 3 LCD Panel Connection Example ×' : Any data can be stored because the LCD panel does not have a corresponding segment. × : Any data can be stored at any time because of the division by 3 display. COM2 COM3 S20 S19 S18 S17 S16 S15 S14 S13 S12 S11 S10 OPEN CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-121. Division by 3 LCD Drive Waveform Example (1/2 Bias method) TF VLC0 COM0 VLC1, 2 VSS VLC0 COM1 VLC1, 2 VSS VLC0 COM2 VLC1, 2 VSS VLC0 S6 VLC1, 2 VSS +VLCD +1/2 VLCD COM0 to S6 0 –1/2 VLCD –VLCD +VLCD +1/2 VLCD COM1 to S6 0 –1/2 VLCD –VLCD +VLCD +1/2 VLCD COM2 to S6 0 –1/2 VLCD –VLCD 293 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-122. Division by 3 LCD Drive Waveform Example (1/3 Bias method) TF VLC0 COM0 VLC1 VLC2 VSS VLC0 VLC1 COM1 VLC2 VSS VLC0 VLC1 COM2 VLC2 VSS VLC0 VLC1 S6 VLC2 VSS +VLCD +1/3 VLCD 0 COM0 to S6 –1/3 VLCD –VLCD +VLCD +1/3 VLCD 0 COM1 to S6 –1/3 VLCD –VLCD +VLCD +1/3 VLCD 0 COM2 to S6 –1/3 VLCD –VLCD 294 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION (4) Division by 4 display example Figure 5-124 shows connection of the division by 4 mode 12-digit LCD panel having the display pattern shown in Figure 5-123, the µPD753108 segment signals (S0 to S23), and the common signals (COM0 to COM3). In this example, “123456.789012” is displayed. The contents of the display data memory (addresses 1E0H to 1F7H) correspond to the display pattern. Here, “6.” at the 7th digit position is taken as an example. It is necessary to output the selection and nonselection voltages as shown in Table 5-22 to the S12 and S13 pins at the COM0 to COM3 common signal timing according to the display pattern shown in Figure 5-123. Table 5-22. S12, S13 Pin Selection and Non-selection Voltage (Division by 4 Display Example) Segment S12 Common COM0 COM1 COM2 COM3 Selection Non-selection Selection Selection Selection Selection Selection Selection S13 This shows that the bits at display data memory address 1ECH corresponding to S12 need to be set to 1101. Figure 5-125 shows LCD drive waveforms for S12, COM0, and COM1 signals (waveforms for COM2 and COM3 are omitted because of space limitation). This shows an alternating current square wave of +VLCD/–VLCD that is the LCD on level being generated when S12 becomes the selection voltage at the COM0 selection timing. Figure 5-123. Division by 4 Mode LCD Display Pattern and Electrode Connection Sn COM0 COM2 Sn + 1 ,, , ,, , 
 ,

, ,,,,  , ,, ,   ,  , , COM1 , COM3 295 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-124. Division by 4 LCD Panel Connection Example µ PD753108 TIMING STROBE COM3 COM2 COM1 COM0 BIT0 BIT1 BIT2 BIT3 1E0 H 1 2 3 4 5 6 DATA MEMORY ADDRESS 0 1 1 1 S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 LCD PANEL 1 1 1 0 1 0 1 1 1 1 0 1 0 1 1 1 0 1 1 0 0 1 1 1 7 8 9 A B C D E F 1F0H 1 2 3 4 5 6 1F7H 1 1 1 1 0 0 0 1 0 0 0 0 1 0 0 0 S10 S11 S12 S13 S14 S15 S16 S17 S18 S19 S20 S21 S22 S23 1 1 0 1 0 1 1 1 1 1 1 1 1 0 1 1 1 1 0 1 0 1 0 0 1 1 0 1 1 1 1 0 1 1 0 1 0 0 0 296 0 0 1 0 1 0 0 0 1 0 1 1 0 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Figure 5-125. Division by 4 LCD Drive Waveform Example (1/3 Bias method) TF VLC0 VLC1 COM0 VLC2 VSS VLC0 VLC1 COM1 VLC2 VSS VLC0 VLC1 COM2 VLC2 VSS VLC0 COM3 VLC1 VLC2 VSS VLC0 VLC1 S12 VLC2 VSS +VLCD +1/3 VLCD COM0 to S12 0 –1/3 VLCD –VLCD +VLCD +1/3 VLCD COM1 to S12 0 –1/3 VLCD –VLCD 297 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION 5.8 Bit Sequential Buffer ··· 16 Bits The bit sequential buffer (BSB) is a special data memory for bit manipulation and the bit manipulation can be easily performed by changing the address specification and bit specification in sequence, therefore it is useful when processing a long data bit-wise. The data memory is composed of 16 bits and the pmem.@L addressing of a bit manipulation instruction is possible. The bit can be specified indirectly by the L register. In this case, processing can be done by moving the specified bit in sequence by incrementing and decrementing the L register in the program loop. Figure 5-126. Bit Sequential Buffer Format Address Bit Symbol 3 FC3H 2 1 0 3 FC2H 2 1 0 3 FC1H 2 1 0 3 FC0H 2 1 0 BSB3 BSB2 BSB1 BSB0 L register L = FH L = CH L = BH L = 8H L = 7H DECS L INCS L L = 4H L = 3H L = 0H Remarks 1. In the pmem.@L addressing, the specified bit moves corresponding to the L register. 2. In the pmem.@L addressing, the BSB can be manipulated regardless of MBE/MBS specification. Data can be operated by direct addressing. It can be used for continuous input and output of 1-bit data together with the 1-bit/4-bit/8-bit direct addressing and pmem.@L addressing. For 8-bit manipulation, the BSB0 and BSB2 must be specified to manipulate the high-order 8-bits and low-order 8 bits. 298 CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Example The 16-bit data of BUFF 1, 2 is output serially starting with the bit 0 of port 3. CLR1 MOV MOV MOV MOV MOV LOOP0 : SKT BR NOP SET1 BR LOOP1 : CLR1 NOP NOP LOOP2 : INCS BR RET L LOOP0 ; L ← L+1 PORT3.0 LOOP2 PORT3.0 ; Clears the bit 0 of port 3. ; Dummy (timing adjustment) MBE XA, BUFF1 BSB0, XA XA, BUFF2 BSB2, XA L, #0 BSB0, @L LOOP1 ; Dummy (timing adjustment) ; Sets the bit 0 of port 3. ; Tests the specification bit of BSB. ; Sets BSB2, 3. ; Sets BSB0, 1. 299 [MEMO] 300 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION The µPD753108 has eight vectored interrupt sources and two test inputs that can be used for various applications. The interrupt control circuit of the µPD753108 has unique features and can process interrupts at extremely high speed. 6.1 Configuration of Interrupt Control Circuit The interrupt control circuit is configured as shown in Figure 6-1, and each hardware unit is mapped to the data memory space. (1) Interrupt function (a) Vectored interrupt function for hardware control, enabling/disabling the interrupt acceptance by the interrupt enable flag (IE×××) and interrupt master enable flag (IME). (b) Can set any interrupt start address. (c) Multiple interrupts wherein the order of priority can be specified by the interrupt priority select register (IPS). (d) Test function of interrupt request flag (IRQ×××). An interrupt generated can be checked by software. (e) Release the standby mode. An interrupt to be released can be selected by the interrupt enable flag. (2) Test function (a) Test request flag (IRQ×××) generation can be checked by software. (b) Release the standby mode. The test source to be released can be selected by the test enable flag. 301 302 2 1 4 IM2 IM1 IM0 INTBT INT4/P00 INT0/P10 INT1/P11 Note Selector Figure 6-1. Interrupt Control Circuit Block Diagram Internal bus IME IPS Interrupt enable flag (IE×××) IST1 IST0 Decoder CHAPTER 6 IRQBT VRQn Both edge detector Edge detector Edge detector INTCSI INTT0 INTT1 INTT2 INTW IRQ4 IRQ0 IRQ1 IRQCSI IRQT0 IRQT1 IRQT2 IRQW IRQ2 Standby release signal Priority control circuit Vector table address generator INTERRUPT FUNCTION AND TEST FUNCTION INT2/P12 Rising edge detector Selector KR0/P60 KR3/P63 Falling edge detector IM2 Note Noise eliminator (standby release is disabled when noise eliminator is selected) CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION 6.2 Types of Interrupt Sources and Vector Tables The µPD753108 has the following eight types of interrupt sources, and multiple interrupts by software control are allowed. Table 6-1. Types of Interrupt Sources Interrupt Source INTBT INT4 INT0 INT1 INTCSI INTT0 INTT1 INTT2 (Serial data transfer end signal) (Match signal between the count register and modulo register of the timer/event counter 0) (Match signal between the count register and modulo register of the timer/event counter 1) (Match signal between the count register and modulo register of the timer/event counter 2) (Reference interval signal sent from the basic interval timer/watchdog timer) (Detection by both rising edge and falling edge is valid.) (Selects rising edge or falling edge.) External External Internal Internal Internal Internal 2 3 4 5 6 VRQ2 (0004H) VRQ3 (0006H) VRQ4 (0008H) VRQ5 (000AH) VRQ6 (000CH) Internal/ External Internal External Interrupt PriorityNote 1 Vectored Interrupt Request Signal (Vector Table Address) VRQ1 (0002H) Note The priority of interrupts is applied when several interrupt requests are generated simultaneously. 303 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION Figure 6-2. Interrupt Vector Table Address 0002H MBE RBE INTBT/INT4 start address (high-order 6 bits) INTBT/INT4 start address (low-order 8 bits) 0004H MBE RBE INT0 start address (high-order 6 bits) INT0 start address (low-order 8 bits) 0006H MBE RBE INT1 start address (high-order 6 bits) INT1 start address (low-order 8 bits) 0008H MBE RBE INTCSI start address (high-order 6 bits) INTCSI start address (low-order 8 bits) 000AH MBE RBE INTT0 start address (high-order 6 bits) INTT0 start address (low-order 8 bits) 000CH MBE RBE INTT1, INTT2 start address (high-order 6 bits) INTT1, INTT2 start address (low-order 8 bits) The interrupt priority column in Table 6-1 indicates the priority according to which interrupts are executed if two or more interrupts occur at the same time, or if two or more interrupt requests are kept pending. To the vector table, write the start address of interrupt processing, and the set values of MBE and RBE during interrupt processing. The vector table is set by using an assembler pseudo-instruction (VENTn: n = 1 to 6). Example Setting of vector table of INTBT/INT4 VENT1 MBE = 0, RBE = 0, GOTOBT ↑ ↑ ↑ ↑ Vector table of address 0002 Setting of MBE in interrupt processing routine Setting of RBE in interrupt processing routine Symbol indicating start address of interrupt processing routine Caution The contents that are written into the operand of VENTn (n = 1 to 6) instruction (MBE, RBE, start address) are stored into the vector table address of 2n. Example Setting of vector tables of INTBT/INT4 and INTT0 VENT1 VENT5 MBE = 0, RBE = 0, GOTOBT ; INTBT/INT4 start address MBE = 0, RBE = 1, GOTOT0 ; INTT0 start address 304 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION 6.3 Hardware Controlling Interrupt Function (1) Interrupt request flag and interrupt enable flag The µ PD753108 has the following eight interrupt request flags (IRQ××× ) corresponding to the respective interrupt sources: INT0 interrupt request flag (IRQ0) INT1 interrupt request flag (IRQ1) INT4 interrupt request flag (IRQ4) BT interrupt request flag (IRQBT) Serial interface interrupt request flag (IRQCSI) Timer/event counter 0 interrupt request flag (IRQT0) Timer/event counter 1 interrupt request flag (IRQT1) Timer/event counter 2 interrupt request flag (IRQT2) Each interrupt request flag is set to “1” when the corresponding interrupt request is generated, and is automatically cleared to “0” when the interrupt processing is executed. However, because IRQBT and IRQ4 (also IRQT1 and IRQT2) share the vector address, these flags are cleared differently from the other flags (refer to 6.6 Vector Address Share Interrupt Service). The µ PD753108 also has eight interrupt enable flags (IE××× ) corresponding to the respective interrupt request flags. INT0 interrupt enable flag (IE0) INT1 interrupt enable flag (IE1) INT4 interrupt enable flag (IE4) BT interrupt enable flag (IEBT) Serial interface interrupt enable flag (IECSI) Timer/event counter 0 interrupt enable flag (IET0) Timer/event counter 1 interrupt enable flag (IET1) Timer/event counter 2 interrupt enable flag (IET2) When the interrupt enable flag is “1”, the interrupt is enabled; and when it is “0”, the interrupt is disabled. When the interrupt request flag is set and interrupt enable flag enables the interrupt, a vectored interrupt request (VRQn) is generated. It is also used to release the standby mode. The interrupt request flag and interrupt enable flag are operated by a bit manipulation instruction and 4-bit memory manipulation instruction. When the bit manipulation instruction is used, they can be directly manipulated at any time regardless of MBE setting. The interrupt enable flag is manipulated by an EI IE××× instruction and DI IE××× instruction. A SKTCLR instruction is normally used to test the interrupt request flag. Example EI DI SKTCLR IE0 IE1 IRQCSI ; Enables INT0. ; Disables INT1. ; Skips and clears when IRQCSI is 1. When the interrupt request flag is set by an instruction, a vectored interrupt is executed as if an interrupt were generated. The interrupt request flag and interrupt enable flag are cleared to “0” when a RESET signal is generated and all the interrupts are disabled. 305 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION Table 6-2. Set Signals for Interrupt Request Flags Interrupt Request Flag IRQBT IRQ4 IRQ0 IRQ1 IRQCSI IRQT0 IRQT1 IRQT2 Interrupt Enable Flag IEBT IE4 IE0 IE1 IECSI IET0 IET1 IET2 Set Signal for Interrupt Request Flag Set by the reference interval signal by the basic interval timer/watchdog timer. Set by the detection of both rising edge and falling edge of an INT4/P00 pin. Reset by the edge detection of an INT0/P10 pin input signal. The detection edge is selected by the INT0 edge detection mode register (IM0). Reset by the edge detection of an INT1/P11 pin input signal. The detection edge is selected by the INT1 edge detection mode register (IM1). Set by a serial data transfer end signal of the serial interface. Set by a match signal sent from the timer/event counter 0. Set by a match signal sent from the timer/event counter 1. Set by a match signal sent from the timer/event counter 2. (2) Interrupt priority selection register (IPS) The interrupt priority selection register selects the higher-order-priority interrupts in a system wherein multiple interrupts are allowed. Its low-order 3 bits are used for specification. Bit 3 is the interrupt master enable flag (IME) which specifies whether all the interrupts are disabled or not. The IPS is set by a 4-bit memory manipulation instruction. Bit 3 is set and reset by an EI/DI instruction. To change the contents of the lower 3 bits of IPS, the interrupt must be disabled (IME = 0). Example DI CLR1 MOV MOV MBE A, #1011B IPS, A ; Gives higher priority to INT1 and enables interrupt ; Disables interrupt All the bits are cleared to “0” when a RESET signal is generated. 306 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION Figure 6-3. Interrupt Priority Selection Register Address FB2H 3 IPS3 2 IPS2 1 IPS1 0 IPS0 Symbol IPS Selection of higher-order-priority interrupts 0 0 0 0 0 1 No interrupts are handled as higher-order-priority interrupts. VRQ1 (INTBT/INT4) VRQ2 (INT0) VRQ3 (INT1) VRQ4 (INTCSI) VRQ5 (INTT0) VRQ6 (INTT1/INTT2) Setting prohibited The above vectored interrupts are regarded as higher-order priority interrupts. 0 1 0 0 1 1 1 0 0 1 0 1 1 1 0 1 1 1 Interrupt master enable flag (IME) 0 1 Disables all the interrupts and no vectored interrupt is started. Controls interrupt enable/disable by the corresponding interrupt enable flag. 307 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION (3) Hardware of INT0, INT1, and INT4 (a) Figure 6-4 (a) shows the configuration of the INT0. An external interrupt is input to select the detection edge, that is, rising edge or falling edge. The INT0 has a noise eliminator by means of the sampling clock (See Figure 6-5 Noise Eliminator Input/ Output Timing). The noise eliminator removes the pulses which are narrower than the two cycles of the sampling clockNote. However, a pulse which is wider than the one cycle of the sampling clock may be accepted in some cases as an interrupting signal depending on a sampling timing. The pulses which are wider than the two cycles of sampling clock are accepted all the time as interrupting signals (See Figure 6-5 (a)). The INT0 has the two sampling clocks: Φ and fX/64, either of which can be selected. One of them is selected by the bit 3 (IM03) of the INT0 edge detection mode register (IM0) (See Figure 6-6 (a)). The detection edge is selected by the bits 0/1 (IM00/IM01) of the INT0 edge detection mode register (IM0). Figure 6-6 (a) shows the format of the IM0. It is set by a 4-bit manipulation instruction. All the bits are cleared to “0” when the RESET signal is generated and the rising edge specification is adopted. Note 2t CY when the sampling clock is Φ. 128/fX when the sampling clock is fX /64. Cautions 1. Pulses are input to the INT0/P10 pin via a noise eliminator if it is used as a port, therefore pulses longer than the two cycles of sampling clock must be input. 2. When the noise eliminator is selected, that is IM02 is set to 0, the INT0 performs sampling by a clock, therefore it does not operate in the standby mode (the noise eliminator does not operate when the CPU clock Φ is not supplied). Consequently, if the standby mode is to be released by the INT0, the noise eliminator must not be selected, that is the IM02 must be set to 1. (b) Figure 6-4 (b) shows the configuration of the INT1. An external interrupt is input to select the detection edge, rising edge or falling edge. The detection edge is selected by the INT1 edge detection mode register (IM1). Figure 6-6 (b) shows the format of the IM1. It is set by a bit manipulation instruction. All the bits are cleared to “0” when the RESET signal is generated and the rising edge specification is adopted. (c) Figure 6-4 (c) shows the configuration of the INT4. An external interrupt is input so that both the rising edge and falling edge can be detected. 308 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION Figure 6-4. Configurations of INT0, INT1, and INT4 (a) INT0 hardware Selector INT0/P10 Noise eliminatorNote Edge detector INT0 IRQ0 set signal IM02 IM03 IM0 Φ fX/64 Input buffer Internal bus IM00, IM01 SelectorNote Detection edge specification Sampling clock selection 4 Note Even though f X/64 is selected, the HALT mode cannot be released by INT0. (b) INT1 hardware INT1/P11 Edge detector INT1 IRQ1 set signal IM10 IM1 Input buffer 4 Internal bus Detection edge specification (c) INT4 hardware INT4 IRQ4 set signal INT4/P00 Both edge detector Input buffer Internal bus 309 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION Figure 6-5. Noise Eliminator Input/Output Timing tSMP Sampling cycle (tSMP) or less INT0 Shaping output 1 to 2 times INT0 (a) Shaping output “L” H L tSMP L tSMP tSMP tSMP Eliminated as noise H L L H INT0 (b) Shaping output 2 times or more INT0 Shaping output “L” H Eliminated as noise H L L L L L Remark tSMP = t CY or 64/f X 310 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION Figure 6-6. Edge Detection Mode Register Format (a) INT0 edge detection mode register (IM0) Address FB4H 3 IM03 2 IM02 1 IM01 0 IM00 Symbol IM0 IM01 0 0 1 1 IM00 0 1 0 1 Detection Edge Specification Rising edge specification Falling edge specification Rising edge/falling edge specification Ignored (The interrupt request flag is not set). IM02 0 1 Noise Eliminator Select Bit Selects the noise eliminator. Sampling Enabled Standby Release Impossible Possible Does not select the noise eliminator. Disabled IM03 0 1 Sampling Clock Φ (0.67 µ s, 1.33 µ s, 2.67 µ s, 10.7 µ s: 6.00-MHz operation) fX/64 (10.7 µ s : 6.00-MHz operation) (b) INT1 edge detection mode register (IM1) Address 3 FB5H 0 2 0 1 0 0 IM10 Symbol IM1 IM10 0 1 Detection Edge Specification Rising edge specification Falling edge specification Caution When the edge detection mode register is changed, the interrupt request flag may be set in some case, therefore the interrupts must be disabled beforehand to select the mode register and the interrupt request flag must be cleared by a CLR1 instruction, and then the interrupts must be enabled. When f X/64 is selected as the sampling clock by changing the IM0, the interrupt request flag must be cleared when 16 machine cycles have elapsed since the mode register was changed. 311 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION (4) Interrupt status flag The interrupt status flags (IST0 and IST1) indicate the status of the processing currently executed by the CPU and are included in PSW. The interrupt priority control circuit controls nesting of interrupts according to the contents of these flags as shown in Table 6-3. IST0 and IST1 can be changed by using a 4-bit or bit manipulation instruction, and interrupts can be nested with the status under execution changed. IST0 and IST1 can be manipulated in 1-bit units regardless of the setting of MBE. Before manipulating IST0 and IST1, be sure to execute the DI instruction to disable the interrupt. Execute the EI instruction after manipulating the flags to enable the interrupt. IST1 and IST0 are saved to the stack memory along with the other flags of PSW when an interrupt is acknowledged, and their statuses are automatically changed higher by one. When the RETI instruction is executed, the original values of IST1 and IST0 are restored. The contents of these flags are cleared to “0” when the RESET signal is asserted. Table 6-3. IST1 and IST0 and Interrupt Processing Status After Interrupt Acknowledged IST1 0 0 1 1 0 1 0 1 Status 0 Status 1 Status 2 Setting prohibited Executes normal program Processes interrupt with low or high priority Processes interrupt with high priority All interrupts can be acknowledged Interrupt with high priority can be acknowledged Acknowledging all interrupts is disabled 0 1 — IST0 1 0 — IST1 IST0 Status of Processing under Execution Processing by CPU Interrupt Request That Can Be Acknowledged 312 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION 6.4 Interrupt Sequence When an interrupt is generated, it is executed in the following procedure. Figure 6-7. Interrupt Processing Sequence Interrupt (INT×××) is generated. IRQ××× is set. IE××× is set? YES Corresponding VRQn is generated. NO Held until IE××× is set. IME = 1 NO Held until IME is set. Held until the current operation ends. YES VRQn is higher-order priority interrupt? YES Note 1 IST1, 0 = 00 or 01 NO Note 1 IST1, 0 = 00 YES NO NO YES Select one of the several VRQn's generated simultaneously according to the order of the interrupts in Table 6-1. Selected VRQn Remaining VRQn Save the contents of the PC and PSW in the stack memory and set the dataNote 2 in the vector table corresponding to the started VRQn in the PC, RBE, and MBE. Change the contents of IST0,1 to 01 if 00, or to 10 if 01. Reset the accepted IRQ×××. See 6.6, if the interrupt source shares the vector address. Jump to the interrupt service program execution starting address. Notes 1. IST1, 0: interrupt status flag (bits 2, 3 of PSW; see Table 6-3 ) 2. Each vector table stores the interrupt service program starting address and values set for the MBE and RBE at the time the interrupt service starts. 313 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION 6.5 Multiple Interrupt Service Control The µ PD753108 accepts multiple interrupts in the following two methods. (1) Multiple interrupts wherein higher-order priority interrupts are specified This is a standard multiple interrupts method of the µPD753108, wherein one of the interrupt sources is selected to enable the multiple interrupts (double interrupts) of the interrupt. That is, the higher-order priority interrupts specified by the interrupt priority selection register (IPS) can be accepted when the status of the current operation is 0 and 1, and the other lower-order priority interrupts can be serviced when the status is 0 (See Figure 6-8 and Table 6-3 ). Therefore, if this method is used when you wish to nest only one interrupt, operations such as enabling and disabling interrupts while the interrupt is processed need not to be performed, and the nesting level can be kept to 2. Figure 6-8. Multiple Interrupts by Higher-Order Priority Interrupts Lower-order priority or higher-order priority interrupt service (status 1) Higher-order priority interrupt service (status 2) Normal processing (status 0) Interrupt is disabled. IPS is set. Interrupt is enabled. Lower-order priority or higher-order priority interrupt is generated. Higher-order priority interrupt is generated. 314 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION (2) Multiple interrupts changing the interrupt status flag If the interrupt status flag is changed by the program, multiple interrupts can be accepted. That is, if IST1 and IST0 are changed to “0, 0” (status 0), multiple interrupts can be serviced. This method is used when multiple interrupts (two or more interrupts) are to be accepted. The IST1 and IST0 must be changed beforehand in a status in which the interrupts are disabled by a DI instruction. Figure 6-9. Multiple Interrupts by Changing Interrupt Status Flag Normal processing (status 0) Single interrupt Double interrupts Interrupts are disabled. IPS is set. Status 1 Interrupts are enabled. Interrupts are disabled. IST is changed. Lower-order priority interrupts or higher-order priority interrupts are generated. Interrupts are enabled. Lower-order priority interrups or higherorder priority interrupts are generated. Status 0 Status 0 Status 1 315 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION 6.6 Vector Address Share Interrupt Service Because INTBT, INT4 and INTT1, INTT2 interrupt sources share the vector table addresses, interrupt source selection is made as described below: (1) To use one interrupt only Set the interrupt enable flag to 1 for the required one of the two interrupt sources sharing the vector table addresses, and clear the interrupt enable flag of the other interrupt source. In this case, an interrupt request is generated from the interrupt source corresponding to the interrupt enable flag that is set to 1 (IE××× = 1). When the interrupt request is acknowledged, the interrupt request flag is cleared. (2) To use both interrupts Set both the interrupt enable flags of the two interrupt sources to 1. In this case, an interrupt request is made by ORing the interrupt request flags of the two interrupt sources. Even if an interrupt request is acknowledged when either or both of the interrupt request flags are set to 1, the interrupt request flags are not reset. Therefore, the interrupt service routine must decide which interrupt source the interrupt is generated from. This is accomplished by executing the SKTCLR instruction at the beginning of interrupt service routine to check the interrupt request flags. If both the request flags are set when this request flag is tested and cleared, the interrupt request remains even if one of the request flags is cleared. If this interrupt is selected as having the higher priority, nesting processing is started by the remaining interrupt request. Consequently, the interrupt request not tested is processed first. If the selected interrupt has the lower priority, the remaining interrupt is kept pending and therefore, the interrupt request tested is processed first. Therefore, an interrupt sharing a vector address with another interrupt is identified differently, depending whether it has the higher priority, as shown in Table 6-4. Table 6-4. Identifying Interrupt Sharing Vector Table Address With higher priority With lower priority Interrupt is disabled and interrupt request flag of interrupt that takes precedence is tested Interrupt request flag of interrupt source that takes precedence is tested 316 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION Examples 1. To use both INTBT and INT4 as having the higher priority and give priority to INT4 DI SKTCLR BR EI RETI . . . . VSUBBT: CLR1 . . . . . . . . EI RETI 2. To use both INTBT and INT4 as having the lower priority and give priority to INT4 SKTCLR BR . . . . . . . . . IRQ4 VSUBBT Processing routine of INT4 ; IRQ4 = 1 ? IRQBT Processing routine of INTBT . . . . IRQ4 VSUBBT Processing routine of INT4 ; IRQ4 = 1 ? RETI . . . . VSUBBT: CLR1 . . . . . . . . . . RETI IRQBT Processing routine of INTBT 317 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION 6.7 Machine Cycles until Interrupt Processing The number of machine cycles required since an interrupt request flag (IRQ××× ) has been set until the interrupt routine is executed is as follows: (1) If IRQ××× is set while interrupt control instruction is executed If IRQ××× is set while an interrupt control instruction is executed, the next one instruction is executed. Then three machine cycles of interrupt processing is performed and the interrupt routine is executed. Interrupt control instruction        A B C D A: Sets IRQ××× B: Executes next one instruction (1 to 3 machine cycles; differs depending on instruction) C: Interrupt processing (3 machine cycles) D: Executes interrupt routine Cautions 1. If two or more interrupt control instructions are described in a row, these control instructions will be all executed consecutively. After having executed the last one, interrupt processing of three machine cycles will be performed, followed by the interrupt routine. 2. If the DI instruction is executed when or after IRQ××× is set (A in the above figure), the interrupt request corresponding to IRQ××× that has been set is kept pending until the EI instruction is executed next time. Remarks 1. An interrupt control instruction manipulates the hardware units related to interrupt (address FB ×H of the data memory). The DI and EI instructions are interrupt control instructions. 2. The three machine cycles of interrupt processing are the time required to manipulate the stack which is manipulated when an interrupt is acknowledged. 318 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION (2) If IRQ××× is set while instruction other than (1) is executed (a) If IRQ××× is set at the last machine cycle of the instruction under execution In this case, the one instruction following the instruction under execution is executed, three machine cycles of interrupt processing are performed, and finally the interrupt routine is executed. Instruction other than interrupt control instruction A B C D A: Sets IRQ××× B: Executes next one instruction (1 to 3 machine cycles; differs depending on instruction) C: Interrupt processing (3 machine cycles) D: Executes interrupt routine Caution If the next instruction is an interrupt control instruction, the one instruction following the interrupt control instruction executed last is executed, three machine cycles of interrupt processing are performed, and finally the interrupt routine is executed. If the DI instruction is executed after IRQ××× has been set, the interrupt request corresponding to the set IRQ××× is kept pending. (b) If IRQ××× is set before the last machine cycle of the instruction under execution In this case, three machine cycles of interrupt processing are performed after execution of the current instruction, and then the interrupt routine is executed. Instruction other than interrupt control instruction          A C D A: Sets IRQ××× C: Interrupt processing (3 machine cycles) D: Executes interrupt routine 319 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION 6.8 Effective Usage of Interrupt Use the interrupt function effectively as follows: (1) Set MBE to 0 in interrupt processing routine. If the memory used in the interrupt routine is allocated to addresses 00H through 7FH, and MBE is cleared to 0 by the interrupt vector table, you can program without having to consider the memory bank. If it is necessary to use memory bank 1, save the memory bank selection register by using the PUSH BS instruction and then select memory bank 1. (2) Use different register banks for the normal routine and interrupt routine. The normal routine uses register banks 2 and 3 with RBE = 1 and RBS = 2. If the interrupt routine is for one nested interrupt, use register bank 0 with RBE = 0, so that you do not have to save or restore the registers. When two or more interrupts are nested, set RBE to 1, save the register bank by using the PUSH BS instruction, and set RBS to 1 to select register bank 1. (3) Use the software interrupt for debugging. Even if an interrupt request flag is set by an instruction, the same operation as when an interrupt occurs is performed. For debugging of an irregular interrupt or debugging when two or more interrupts occur at the same time, the efficiency can be enhanced by setting the interrupt flag by an instruction. 6.9 Application of Interrupt To use the interrupt function, first set as follows by the main routine: (a) Set the interrupt enable flag of the interrupt used (by using the EI IE××× instruction). (b) To use INT0 or INT1, select the active edge (set IM0 or IM1). (c) To use nesting (of an interrupt with the higher priority), set IPS (IME can be set at the same time). (d) Set the interrupt master enable flag (by using the EI instruction). In the interrupt routine, MBE and RBE are set by the vector table. However, when the interrupt specified as having the higher priority is processed, the register bank must be saved and set. To return from the interrupt routine, use the RETI instruction. 320 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION (1) Enabling or disabling interrupt Reset EI IE0 EI IET1 EI Disables interrupts Enables INT0 and INTT1 DI IE0 Enables INTT1 DI Disables interrupts All the interrupts are disabled by the RESET signal. An interrupt enable flag is set by the EI IE××× instruction. At this stage, the interrupts are still disabled. The interrupt master enable flag is set by the EI instruction. INT0 and INTT1 are enabled at this time. The interrupt enable flag is cleared by the DI IE ××× instruction, and INT0 is disabled. All the interrupts are disabled by the DI instruction. 321 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION (2) Example of using INTBT, INT0 (falling edge active), and INTT0. No multiple interrupt (all interrupts have lower priority) Reset ; RBE = 1, MBE = 0 SEL MOV MOV CLR1 EI EI EI EI RB2 A, #1 IM0, A IRQ0 IEBT IE0 IET0 Status 0 ; RBE = 0 INT0 Status 1 Status 0 RETI All the interrupts are disabled by the RESET signal and status 0 is set. RBE = 1 is specified by the reset vector table. The SEL RB2 instruction uses register banks 2 and 3. INT0 is specified to be active at the falling edge. The interrupt is enabled by the EI, EI IE××× instruction. The INT0 interrupt routine is started at the falling edge of INT0. The status is changed to 1, and all the interrupts are disabled. RBE = 0, and register banks 0 and 1 are used. Execution returns from the interrupt routine when the RETI instruction is executed. The status is returned to 0 and the interrupt is enabled. Remark If all the interrupts are used as having the lower priority as shown in this example, saving or restoring the register bank is not necessary if RBE = 1 and RBS = 2 for the main routine and register banks 2 and 3 are used, and RBE = 0 for the interrupt routine and register banks 0 and 1 are used. 322 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION (3) Nesting of interrupts with higher priority (INTBT has higher priority and INTT0 and INTCSI have lower priority) Reset SEL EI EI EI MOV MOV RB2 IEBT IET0 IECSI A, #9 IPS, A ; RBE = 1, MBE = 0 Status 0 ; RBE = 0 INTT0 Status 1 ; RBE = 1 SEL RB1 INTBT Status 2 SEL RB2 RETI Status 1 Status 0 RETI INTBT is specified as having the higher priority by setting of IPS, and the interrupt is enabled at the same time. INTT0 processing routine is started when INTT0 with the lower priority occurs. Status 1 is set and the other interrupts with the lower priority are disabled. RBE = 0 to select register bank 0. INTBT with the higher priority occurs. The interrupts are nested. The status is changed to 0 and all the interrupts are disabled. RBE = 1 and RBS = 1 to select register bank 1 (only the registers used may be saved by the PUSH instruction). RBS is returned to 2, and execution returns to the main routine. The status is returned to 1. 323 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION (4) Executing pending interrupt – interrupt input while interrupts are disabled – Reset EI IE0 INT0 EI INTCSI RETI EI IECSI RETI The request flag is kept pending even if INT0 is set while the interrupts are disabled. INT0 processing routine is started when the interrupts are enabled by the EI instruction. Same as . INTCSI processing routine is started when the pending INTCSI is enabled. 324 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION (5) Executing pending interrupt – two interrupts with lower priority occur simultaneously – Reset EI IET0 EI IE0 EI INT0 INTT0 RETI RETI If INT0 and INTT0 with the lower priority occur at the same time (while the same instruction is executed), INT0 with the higher priority is executed first (INTT0 is kept pending). When the INT0 processing routine is terminated by the RETI instruction, the pending INTT0 processing routine is started. 325 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION (6) Executing pending interrupt – interrupt occurs during interrupt processing (INTBT has higher priority and INTT0 and INTCSI have lower priority) – Reset EI EI EI MOV MOV IEBT IET0 IECSI A, #9 IPS, A PUSH rp INTCSI POP rp RETI INTBT INTT0 RETI RETI If INTBT with the higher priority and INTT0 with the lower priority occur at the same time, the processing of the interrupt with the higher priority is started (if there is no possibility that an interrupt with the higher priority occurs while another interrupt with the higher priority is processed, DI IE ×× is not necessary). If an interrupt with the lower priority occurs while the interrupt with the higher priority is executed, the interrupt with the lower priority is kept pending. When the interrupt with the higher priority has been processed, INTCSI with the higher priority of the pending interrupts is executed. When the processing of INTCSI has been completed, the pending INTT0 is processed. 326 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION (7) Enabling two nesting of interrupts – INTT0 and INT0 are nested doubly and INTCSI and INT4 are nested singly – Reset EI EI EI EI EI IET0 IE0 IECSI IE4 Status 0 DI CLR1 IST0 IECSI DI IE4 DI EI Status 0 Status 1 INTCSI Status 0 INTT0 Status 1 RETI Status 0 EI EI RETI IECSI IE4 When INTCSI that does not enable nesting occurs, the INTCSI processing routine is started. The status is 1. The status is changed to 0 by clearing IST0. INTCSI and INT4 that do not enable nesting are disabled. When INTT0 that enables nesting occurs, nesting is executed. The status is changed to 1, and all the interrupts are disabled. The status is returned to 0 when INTT0 processing is completed. The disabled INTCSI and INT4 are enabled, and execution returns to the main routine. 327 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION 6.10 6.10.1 Test Function Types of test sources The µ PD753108 has two types of test sources. Of these, INT2 is provided with two types of edge-detection testable inputs. Table 6-5. Types of Test Sources Test Source INT2 (detects rising edge input to INT2 or falling edge input to KR0 to KR3) INTW (signal from watch timer) Internal Internal/External External 6.10.2 Hardware devices controlling test function (1) Test request flag, test enable flag The test request flag (IRQ××× ) is set to “1” when a test request (INT××× ) is generated. When the test processing is completed, it must be cleared to “0” by software. The test enable flag (IE××× ) is annexed to each test request flag. When it is “1”, a standby release signal is enabled; and when it is “0”, the signal is disabled. When both the test request flag and test enable flag are set to “1”, a standby release signal is generated. Table 6-6 lists the set signals for the test request flags. Table 6-6. Set Signal for Test Request Flag Test Request Flag IRQW IRQ2 Set Signal for Test Request Flag Set by a signal sent from the watch timer. Test Enable Flag IEW Set by either the rising edge detection of a signal input to the INT2/P12 pin or the falling IE2 edge detection of a signal input to the KR0/P60 to KR3/P63 pins. The detection edge is selected by the INT2 edge detection mode register (IM2). 328 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION (2) INT2, key interrupt (KR0 to KR3) hardware Figure 6-10 shows the configuration of INT2 and KR0 to KR3. The IRQ2 set signal is output by the edge detection at the following two series of pins. The pin is selected by the INT2 edge detection mode register (IM2). (a) Rising edge detection of input to INT2 pin The IRQ2 is set when the rising edge of a signal input to the INT2 pin is detected. (b) Falling edge detection of a signal input to KR0 to KR3 pins (key interrupt) A pin which is used for the interrupt input is selected among the KR0 to KR3 pins by the INT2 edge detection mode register (IM2). The IRQ2 is set by the falling edge detection of a signal input to a selected pin. Figure 6-11 shows the format of the IM2. The IM2 is set by a 4-bit manipulation instruction. All the bits are cleared to “0” by a RESET signal and the rising edge specification by the INT2 is adopted. 329 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION Figure 6-10. INT2 and KR0 to KR3 Block Diagram INT2/P12 Rising edge detection circuit Selector INT2 IRQ2 set signal Falling edge detection circuit KR3/P63 IM20, IM21 KR2/P62 KR1/P61 KR0/P60 Input buffers IM2 4 Internal bus 330 CHAPTER 6 INTERRUPT FUNCTION AND TEST FUNCTION Figure 6-11. Format of INT2 Edge Detection Mode Register (IM2) Address FB6H 3 0 2 0 1 IM21 0 IM20 Symbol IM2 IM21 0 0 1 1 IM20 0 1 0 1 INT2 Test Source Rising edge specification of INT2 pin input Setting prohibited Falling edge specification of any KRX pin input Interrupt Input Pin INT2 — KR2, KR3 KR0 to KR3 (2) (4) (1) Cautions 1. If the edge detection mode register is changed, the test request flag may be set in some cases; therefore the test input must be disabled beforehand to change the mode register and the test request flag must be cleared by a CLR1 instruction, and then a test input must be enabled. 2. When a low-level signal is input to a pin among those pins selected for falling edge detection, the IRQ2 is not set even if falling edges are input to the other pins. 331 [MEMO] 332 CHAPTER 7 STANDBY FUNCTION The µPD753108 has a standby function that reduces the power dissipation of the system. This standby function can be implemented in the following two modes: • STOP mode • HALT mode The functions of the STOP and HALT modes are as follows: (1) STOP mode In this mode, the main system clock oscillation circuit is stopped and therefore, the entire system is stopped. The current dissipation of the CPU is substantially reduced. Moreover, the contents of the data memory can be retained at a low voltage (VDD = 1.8 V MIN.). This mode is therefore useful for retaining the data memory contents with an extremely low current dissipation. The STOP mode of the µPD753108 can be released by an interrupt request; therefore, the microcontroller can operate intermittently. However, because a wait time is required for stabilizing the oscillation of the clock oscillation circuit when the STOP mode has been released, use the HALT mode if processing must be started immediately after the standby mode has been released by an interrupt request. (2) HALT mode In this mode, the operating clock of the CPU is stopped. Oscillation of the system clock oscillation circuit continues. This mode does not reduce the current dissipation as much as the STOP mode, but it is useful when processing must be resumed immediately when an interrupt request is issued, or for an intermittent operation such as a watch operation. In either mode, all the contents of the registers, flags, and data memory immediately before the standby mode is set are retained. Moreover, the contents of the output latches and output buffers of the I/O ports are also retained; therefore, the statuses of the I/O ports are processed in advance so that the current dissipation of the overall system can be minimized. The following page describes the points to be noted in using the standby mode. 333 CHAPTER 7 STANDBY FUNCTION Cautions 1. The STOP mode can be used only when the system operates with the main system clock (oscillation of the subsystem clock cannot be stopped). The HALT mode can be used regardless of whether the system operates with the main system clock or subsystem clock. 2. If the STOP mode is set when the LCD controller/driver and watch timer operate with main system clock fX , the operations of the LCD controller/driver and watch timer are stopped. To continue the operations of these, therefore, change the operating clock to subsystem clock fXT before setting the STOP mode. 3. Efficient operation with a low current dissipation at a low voltage can be performed by selecting the standby mode, CPU clock, and system clock. In any case, however, the time described in 5.2.3 Setting of system clock and CPU clock is required until the operation is started with the new clock when the clock has been changed by manipulating the control register. To use the clock selecting function and standby mode in combination, therefore, set the standby mode after the time required for selection has elapsed. 4. To use the standby mode, process so that the current dissipation of the I/O ports is minimized. Especially, do not open the input port, and be sure to input low or high level to it. 334 CHAPTER 7 STANDBY FUNCTION 7.1 Standby Mode Setting and Operation Status Table 7-1. Operation Status in Standby Mode Item Set instruction System clock when set Mode STOP Mode STOP instruction Settable only when the main system clock is used. Only the main system clock stops oscillation. Operation stops. HALT Mode HALT instruction Settable both by the main system clock and subsystem clock. Only the CPU clock Φ halts (oscillation continues). Operable only when the main system clock is oscillated (The IRQBT is set in the reference interval). Operable only when an external SCK input is selected as the serial clock or when the main system clock is oscillated. Operable only when a signal input to the TI0 to TI2 pins is specified as the count clock or when the main system clock is oscillated. Operable. Operable. Operation Clock generator status Basic interval timer/ Watchdog timer Serial interface Operable only when an external SCK input is selected as the serial clock. Operable only when a signal input to the TI0 to TI2 pins is specified as the count clock. Operable when fXT is selected as the count clock. Operable only when fXT is selected as the LCDCL. The INT1, 2, and 4 are operable. Only the INT0 is not operatedNote . The operation stops. Timer/event counter Watch timer LCD controller/driver External interrupt CPU Release signal Interrupt request signal sent from the operable hardware enabled by the interrupt enable flag or RESET signal input. Note Can operate only when the noise eliminator is not used (IM02 = 1) by bit 2 of the edge detection mode register (IM0). 335 CHAPTER 7 STANDBY FUNCTION The STOP mode is set by a STOP instruction and the HALT mode is set by a HALT instruction. The STOP instruction and HALT instruction set bit 3 and bit 2, respectively, of the PCC. A NOP instruction must be placed following the STOP instruction and HALT instruction. When changing the CPU clock by the low-order 2 bits of the PCC, there may be a time difference between PCC updating and CPU clock change as shown in Table 5-5 Maximum Time Required to Switch System to/from CPU Clocks. Consequently, when the operating clock before the standby mode and the CPU clock after the standby mode is released are to be changed, the PCC must be updated and then the standby mode must be set after the machine cycle necessary to change the CPU clock has elapsed. In the standby mode, the data items stored in all the registers and data memory such as the general-purpose register, flags, mode registers, and output latch which stop operation during the standby mode are held. Cautions 1. When the system is set in the STOP mode, the X2 pin is pulled up internally to VDD with the 50-kΩ (TYP.) resistor. 2. Before setting the standby mode, reset all the interrupt request flags. If there is an interrupt source in which both the test request flag and test enable flag are set, the standby mode is released at the moment the system enters it (See Figure 6-1 Interrupt Control Circuit Block Diagram). However, when the STOP mode is set, the system enters the HALT mode immediately after a STOP instruction is executed and then returns to the operating mode after waiting for a time which is set in the BTM register. 336 CHAPTER 7 STANDBY FUNCTION 7.2 Standby Mode Release The standby mode (STOP or HALT) is released when an interrupt request signal enabled with an interrupt enable flag occurs or a RESET signal is generated. Figure 7-1 shows the standby mode release operation. Figure 7-1. Standby Mode Release Operation (1/2) (a) STOP mode release when a RESET signal is generated Wait Note STOP instruction RESET signal Operation mode STOP mode HALT mode Operation mode Clock Oscillation Oscillation stop Oscillation (b) STOP mode release when an interrupt occurs Wait (setup time in BTM) STOP instruction Standby release signal Operation mode STOP mode HALT mode Operation mode Clock Oscillation Oscillation stop Oscillation Note The following two wait times can be specified by the mask option. 2 17/f X (21.8 ms at 6.00 MHz, 31.3 ms at 4.19 MHz) 2 15/f X (5.46 ms at 6.00 MHz, 7.81 ms at 4.19 MHz) However, the µPD75P3116 has no mask options and it is fixed to 2 15 /fX . Remark Broken line: When the interrupt request to release the standby mode is acknowledged. 337 CHAPTER 7 STANDBY FUNCTION Figure 7-1. Standby Mode Release Operation (2/2) (c) HALT mode release when a RESET signal is generated HALT instruction RESET signal Operation mode HALT mode Operation mode Wait Note Clock Oscillation (d) HALT mode release when an interrupt occurs HALT instruction Standby release signal Operation mode HALT mode Operation mode Clock Oscillation Note The following two wait times can be specified by the mask option. 2 17/f X (21.8 ms at 6.00 MHz, 31.3 ms at 4.19 MHz) 2 15/f X (5.46 ms at 6.00 MHz, 7.81 ms at 4.19 MHz) However, the µPD75P3116 has no mask options and it is fixed to 2 15 /fX . Remark Broken line: When the interrupt request to release the standby mode is acknowledged. When the STOP mode has been released by an interrupt, the wait time is determined by the setting of BTM (refer to Table 7-2). The time required for the oscillation to stabilize varies depending on the type of the resonator used and the supply voltage when the STOP mode has been released. Therefore, select the appropriate wait time depending on a given condition, and set BTM before setting the STOP mode. 338 CHAPTER 7 STANDBY FUNCTION Table 7-2. Wait Time Selection by Using BTM Wait TimeNote BTM3 – – – – BTM2 0 0 1 1 BTM1 0 1 0 1 BTM0 0 1 1 1 About When f X = 6.00 MHz 2 20/f X (about 175 ms) When f X = 4.19 MHz About 2 20/fX (about 250 ms) About 2 17/fX (about 31.3 ms) About 2 15/fX (about 7.81 ms) About 2 13/fX (about 1.95 ms) About 2 17/fX (about 21.8 ms) About 2 15/fX (about 5.46 ms) About 2 13/fX (about 1.37 ms) Setting prohibited Other than the above Note This time does not include the time until oscillation is started after the STOP mode is released. Caution The wait time that elapses when the STOP mode has been released does not include the time that elapses until the clock oscillation is started after the STOP mode has been released (a in Figure 7-2), regardless of whether the STOP mode has been released by the RESET signal or occurrence of an interrupt. Figure 7-2. Wait Time when STOP Mode is Released STOP mode release X1 pin voltage waveform a VSS 7.3 Operation After Releasing Standby Mode (1) When the standby mode is released by a RESET signal generation, the normal reset operation is performed. (2) When the standby mode is released by generation of an interrupt, whether a vectored interrupt is to be serviced or not at the time the CPU resumes instruction execution is determined by the contents of the interrupt master enable flag (IME). (a) When IME = 0 Following the release of the standby mode, the instruction execution resumes starting with the instruction subsequent to the standby mode setting instruction. The interrupt request flag is held. (b) When IME = 1 After the standby mode is released, two instructions are executed and then a vectored interrupt is executed. However, if the standby mode is released by the INTW and INT2 (testable inputs), a vectored interrupt is not generated; therefore the operations identical to (a) above are performed. 339 CHAPTER 7 STANDBY FUNCTION 7.4 Mask Option Selection In the standby function of the µ PD753108, the wait time after the standby function release by the RESET signal generation can be selected from the following two types of times with the mask option. 217 /f X (21.8 ms: 6.0-MHz operation, 31.3 ms: 4.19-MHz operation) 215 /f X (5.46 ms: 6.0-MHz operation, 7.81 ms: 4.19-MHz operation) The µ PD75P3116, however, does not have mask option and its wait time is fixed to 215 /fX . 7.5 Application of Standby Mode Use the standby mode in the following procedure: Detect the cause that sets the standby mode, such as an interrupt input or power failure by port input (use of INT4 to detect a power failure is recommended). Process the I/O ports (process so that the current dissipation is minimized). It is important not to open the input port. Be sure to input a low or high level to it. Specify an interrupt that releases the standby mode (use of INT4 is effective. Clear the interrupt enable flags of the interrupts that do not release the standby mode). Specify the operation to be performed after the standby mode has been released (manipulate IME depending on whether interrupt processing is performed or not). Specify the CPU clock to be used after the standby mode has been released (to change the clock, make sure that the necessary machine cycles elapse before the standby mode is set). Select the wait time to elapse after the standby mode has been released. Set the standby mode (by using the STOP or HALT instruction). By using the standby mode in combination with the system clock selecting function, low current dissipation and low-voltage operation can be realized. 340 CHAPTER 7 STANDBY FUNCTION (1) Application example of STOP mode (fX = 4.19 MHz) • The STOP mode is set at the falling edge of INT4 and released at the rising edge (INTBT is not used). • All the I/O ports go into a high-impedance state (if the pins are externally processed so that the current dissipation is reduced in a high-impedance state). • Interrupts INT0 and INTT0 are used in the program. However, these interrupts are not used to release the STOP mode. • The interrupts are enabled even after the STOP mode has been released. • After the STOP mode has been released, operation is started with the slowest CPU clock. • The wait time that elapses after the mode has been released is about 31.3 ms. • A wait time of 31.3 ms elapses until the power supply stabilizes after the mode has been released. The P00/INT4 pin is checked two times to eliminate chattering. VDD VDD pin voltage 0V P00/INT4 Low-speed High-speed operation operation Wait CPU operation Operation mode INT4 STOP instruction INT4 STOP mode 31.3 ms 31.3 ms 341 CHAPTER 7 STANDBY FUNCTION (INT4 processing program, MBE = 0) VSUB4: SKT BR SET1 WAIT: SKT BR SKT BR MOV MOV MOV MOV EI EI RETI PDOWN: MOV MOV MOV MOV MOV MOV MOV DI DI MOV MOV NOP STOP NOP RETI ; Sets STOP mode A, #0 PCC, A XA, #00H LCDM, XA LCDC, A PMGA, XA PMGB, XA IE0 IET0 A, #1011B BTM, A ; Wait time ≅ 31.3 ms ; Disables INT0 and INTT0 ; I/O port in high-impedance state ; LCD display off ; Lowest-speed mode PORT0.0 PDOWN BTM.3 IRQBT WAIT PORT0.0 PDOWN A, #0011B PCC, A XA, #XXH PMGm, XA IE0 IET0 ; Sets high-speed mode ; Sets port mode register ; Checks chattering ; P00 = 1 ? ; Power down ; Power on ; Waits for 31.3 ms 342 CHAPTER 7 STANDBY FUNCTION (2) Application of HALT mode (fX = 4.19 MHz) • The standby mode is set at the falling edge of INT4 and released at the rising edge. • In the standby mode, an intermittent operation is performed at intervals of 250 ms (INTBT). • INT4 and INTBT are assigned with the lower priority. • The slowest CPU clock is selected in the standby mode. VDD VDD pin voltage 0V P00/INT4 CPU operation Operation mode Intermittent operation (HALT mode + low-speed operation) Operation mode (low-speed) 250 ms Operation mode (high-speed) INT4 INT4 343 CHAPTER 7 STANDBY FUNCTION (Initial setting) MOV MOV MOV MOV EI EI EI (Main routine) SKT HALT NOP SKTCLR BR MAIN: CALL . . . . . . . . . . IRQW MAIN WATCH PORT0.0 ; Power supply OK? ; Power down mode ; Power supply OK? ; 0.5-sec flag? ; NO ; Watch subroutine A, #0011B PCC, A XA, #05 WM, XA IE4 IEW ; Enables interrupt ; Subsystem clock ; High-speed mode (INT4 processing routine) VINT4: SKT BR CLR1 MOV MOV WAIT1: SKT BR SKT BR CLR1 RETI PDOWN: MOV MOV MOV SET1 MOV XA, #00H LCDM, XA LCDC, A SCC.0 A, #6 ; Selects subsystem clock ; LCD display off PORT0.0 PDOWN SCC.3 A, #1000B BTM, A IRQBT WAIT1 PORT0.0 PDOWN SCC.0 ; Selects main system clock ; Checks chattering ; Waits for 250 ms ; Main system clock starts oscillating ; Power supply OK?, MBE = 0 344 CHAPTER 7 STANDBY FUNCTION WAIT2: INCS BR SET1 RETI A WAIT2 SCC.3 ; Waits for 32 machine cycles or moreNote ; Main system clock oscillation stops Note For how to select the system clock and CPU clock, refer to 5.2.3 Setting of system clock and CPU clock. Caution To change the system clock from the main system clock to the subsystem clock, wait until the oscillation of the subsystem clock is stabilized. 345 [MEMO] 346 CHAPTER 8 RESET FUNCTION There are two reset inputs: external RESET signal and reset signal sent from the basic interval timer/watchdog timer. When either one of the reset signals are input, an internal reset signal is generated. Figure 8-1 shows the circuit diagram of the above two inputs. Figure 8-1. Configuration of Reset Function RESET Internal reset signal Reset signal sent from the basic interval timer/watchdog timer WDTM Internal bus Generation of the RESET signal causes each device to be initialized as listed in Table 8-1. Figure 8-2 shows the timing chart of the reset operation. Figure 8-2. Reset Operation by RESET Signal Generation Wait Note RESET signal generated Operation mode or standby mode HALT mode Internal reset operation Operation mode Note The following two times can be selected by the mask option. 217/fX (21.8 ms at 6.00 MHz or 31.3 ms at 4.19 MHz) 215/fX (5.46 ms at 6.00 MHz or 7.81 ms at 4.19 MHz) However, the µPD75P3116 has no mask options and it is fixed to 215/fX. 347 CHAPTER 8 RESET FUNCTION Table 8-1. Status of Each Device After Reset (1/2) RESET Signal Generation in Standby Mode RESET Signal Generation in Operation Sets the low-order 4 bits of program memory’s address 0000H to the PC11 to PC8 and the contents of address 0001H to the PC7 to PC0. Sets the low-order 5 bits of program memory’s address 0000H to the PC12 to PC8 and the contents of address 0001H to the PC7 to PC0. Sets the low-order 6 bits of program memory’s address 0000H to the PC13 to PC8 and the contents of address 0001H to the PC7 to PC0. Undefined 0 0 Sets the bit 6 of program memory’s address 0000H to the RBE and bit 7 to the MBE. Undefined 1000B Undefined Undefined 0, 0 Undefined 0 0 0 FFH 0 0, 0 0 FFH 0 0, 0 Hardware Program counter (PC) µPD753104 Sets the low-order 4 bits of program memory’s address 0000H to the PC11 to PC8 and the contents of address 0001H to the PC7 to PC0. Sets the low-order 5 bits of program memory’s address 0000H to the PC12 to PC8 and the contents of address 0001H to the PC7 to PC0. Sets the low-order 6 bits of program memory’s address 0000H to the PC13 to PC8 and the contents of address 0001H to the PC7 to PC0. Held 0 0 Sets the bit 6 of program memory’s address 0000H to the RBE and bit 7 to the MBE. Undefined 1000B Held Held 0, 0 Undefined 0 0 0 FFH 0 0, 0 0 FFH 0 0, 0 µPD753106, µPD753108 µPD75P3116 PSW Carry flag (CY) Skip flag (SK0 to SK2) Interrupt status flag (IST0, IST1) Bank enable flag (MBE, RBE) Stack pointer (SP) Stack bank selection register (SBS) Data memory (RAM) General-purpose register (X, A, H, L, D, E, B, C) Bank selection register (MBS, RBS) Basic interval timer/watchdog timer Timer/event counter (T0) Counter (BT) Mode register (BTM) Watchdog timer enable flag (WDTM) Counter (T0) Modulo register (TMOD0) Mode register (TM0) TOE0, TOUT F/F Timer/event counter (T1) Counter (T1) Modulo register (TMOD1) Mode register (TM1) TOE1, TOUT F/F 348 CHAPTER 8 RESET FUNCTION Table 8-1. Status of Each Device After Reset (2/2) RESET Signal Generation in Standby Mode 0 FFH FFH 0 0, 0 0, 0, 0 0 0 Held 0 0 Held 0 0 0 0 0 0 0 Reset (0) 0 0 0, 0, 0 Off Cleared (0) 0 0 Held RESET Signal Generation in Operation 0 FFH FFH 0 0, 0 0, 0, 0 0 0 Undefined 0 0 Undefined 0 0 0 0 0 0 0 Reset (0) 0 0 0, 0, 0 Off Cleared (0) 0 0 Undefined Hardware Timer/event counter (T2) Counter (T2) Modulo register (TMOD2) High-level period setting modulo register (TMOD2H) Mode register (TM2) TOE2, TOUT F/F REMC, NRZ, NRZB TGCE Watch timer Serial interface Mode register (WM) Shift register (SIO) Operation mode register (CSIM) SBI control register (SBIC) Slave address register (SVA) Clock generator, Processor clock control register (PCC) clock output System clock control register (SCC) circuit Clock output mode register (CLOM) Subsystem clock oscillator control register (SOS) LCD controller/ driver Display mode register (LCDM) Display control register (LCDC) LCD/port selection register (LPS) Interrupt function Interrupt request flag (IRQ××× ) Interrupt enable flag (IE ×××) Interrupt priority selection register (IPS) INT0, 1, 2 mode registers (IM0, IM1, IM2) Digital port Output buffer Output latch I/O mode registers (PMGA, B, C) Pull-up resistor setting register (POGA, B) Bit sequential buffer (BSB0 to BSB3) 349 [MEMO] 350 CHAPTER 9 WRITING AND VERIFYING PROM (PROGRAM MEMORY) The program memory of the µPD75P3116 is a one-time PROM. The memory capacity is as follows: µPD75P3116: 16384 words × 8 bits To write or verify this one-time PROM, the pins shown in Table 9-1 are used. Note that no address input pins are used and that the address is updated by inputting a clock from the X1 pin. Table 9-1. Pins Used to Write or Verify Program Memory Pin Name VPP X1, X2 MD0/P30 to MD3/P33 Function Applies program voltage for writing or verifying program memory (usually, VDD). Inputs clock to update address when program memory is written or verified. Inverted signal of X1 pin is input to X2 pin. Selects operation mode when program memory is written or verified. D0/P60 to D3/P63 (low-order 4) Inputs or outputs 8-bit data when program memory is written or verified. D4/P50 to D7/P53 (high-order 4) VDD Supplies power supply voltage. Supplies 1.8 to 5.5 V for normal operation and +6 V when program memory is written or verified. Cautions 1. The program memory contents of the µPD75P3116 cannot be erased by ultraviolet rays because the µPD75P3116 is not provided with a window for erasure. 2. Connect the pins not used for writing or verifying the program memory to VSS. 351 CHAPTER 9 WRITING AND VERIFYING PROM (PROGRAM MEMORY) 9.1 Operation Mode for Writing/Verifying Program Memory When +6 V is applied to the VDD pin and +12.5 V is applied to the V PP pin of the µPD75P3116, the program memory write/verify mode is set. In this mode, the following operation modes can be selected by using the MD0 through MD3 pins. Table 9-2. Operation Mode Specifies Operation Mode VPP +12.5 V VDD +6 V MD0 H L L H MD1 L H L × MD2 H H H H MD3 L H H H Clears program memory address to 0 Write mode Verify mode Program inhibit mode Operation Mode ×: L or H 352 CHAPTER 9 WRITING AND VERIFYING PROM (PROGRAM MEMORY) 9.2 Writing Program Memory The program memory can be written in the following procedure at high speed: (1) Pull down the unused pins to V SS via a resistor. The X1 pin is low level. (2) Supply 5 V to the V DD and VPP pins. (3) Wait for 10 µs. (4) Set the program memory address 0 clear mode. (5) Supply 6 V to VDD and 12.5 V to V PP. (6) Write data in the 1-ms write mode. (7) Set the verify mode. If the data have been correctly written, proceed to (8). If not, repeat (6) and (7). (8) Additional writing of (number of times data have been written in (6) and (7): X) × 1 ms (9) Input a pulse four times to the X1 pin to update the program memory address (by one). (10) Repeat (6) through (9) until the last address is written. (11) Set the program memory address 0 clear mode. (12) Change the voltage applied to the V DD and VPP pins to 5 V. (13) Turn off the power supply. Steps (2) through (9) above are illustrated below. Repeat X times            Write VPP VPP VDD VDD + 1 VDD X1 D0/P60 to D3/P63 D4/P50 to D7/P53 MD0/P30 Data input Verify Additional write Address increment VDD Data output Data input MD1/P31 MD2/P32 MD3/P33 353 CHAPTER 9 WRITING AND VERIFYING PROM (PROGRAM MEMORY) 9.3 Reading Program Memory The contents of the program memory can be read in the following procedure. Reading is performed in the verify mode. (1) Pull down the unused pins to V SS via a resistor. The X1 pin is low level. (2) Supply 5 V to the V DD and VPP pins. (3) Wait for 10 µs. (4) Set the program memory address 0 clear mode. (5) Supply 6 V to VDD and 12.5 V to V PP. (6) Verify mode. Data at each address is sequentially output while four clock pulses are input to the X1 pin. (7) Set the program memory address 0 clear mode. (8) Change the voltage applied to the V DD and VPP pins to 5 V. (9) Turn off the power supply. Steps (2) through (7) above are illustrated below. VPP VPP VDD VDD + 1 VDD VDD X1 D0/P60 to D3/P63 D4/P50 to D7/P53 Data output Data output MD0/P30 MD1/P31 “L” MD2/P32 MD3/P33 354 CHAPTER 9 WRITING AND VERIFYING PROM (PROGRAM MEMORY) 9.4 Screening of One-Time PROM Because of its structure, it is difficult for NEC to completely test the one-time PROM product before shipment. It is therefore recommended that screening be performed to verify the PROM contents after the necessary data has been written to the PROM and the product has been stored under the following conditions. Storage Temperature 125 ° C Storage Time 24 hours NEC offers for a fee one-time PROM writing, marking, screening, and verifying service called QTOP™ microcontroller. For details, consult an NEC sales representative. 355 [MEMO] 356 CHAPTER 10 MASK OPTION 10.1 Pins The pins of the µPD753108 have the following mask options: Table 10-1. Selecting Mask Option of Pin Pin P50 to P53 VLC0 to VLC2, BIAS Mask Option Pull-up resistor can be connected in 1-bit units. LCD drive power supplying split resistors can be connected to four pins at once. 10.1.1 Mask option of P50 through P53 P50 through P53 (port 5) can be connected with pull-up resistors by mask option. The mask option can be specified in 1-bit units. If the pull-up resistor is connected by mask option, port 5 goes high on reset. If the pull-up resistor is not connected, the port goes into a high-impedance state on reset. Pull-up resistor cannot be connected by mask option in the µPD75P3116. 10.1.2 Mask option of VLC0 through VLC2 Split resistors can be connected to the VLC0 through VLC2 pins (LCD drive power supply) and BIAS pin (external split resistor cutting pin) by mask option. Therefore, LCD drive power can be supplied without an external split resistor according to each bias (for details, refer to 5.7.8 Supply of LCD drive power VLC0 , VLC1, and VLC2). The following three mask options can be selected. No split resistor is connected. A 10-kΩ (typ.) split resistor is connected. A 100-kΩ (typ.) split resistor is connected. The mask option is specified for the VLC0 through VLC2 and BIAS pins at once and cannot be specified in 1-pin units. The BIAS pin goes low on reset when the split resistor is connected to this pin by mask option. When the split resistor is not connected, the BIAS pin goes into a high-impedance state on reset. The µPD75P3116 does not have a mask option, and cannot be connected with a split resistor. Connect an external split resistor to the µPD75P3116, if necessary. 357 CHAPTER 10 MASK OPTION 10.2 Mask Option of Standby Function The standby function of the µ PD753108 allows you to select wait time by using a mask option. The wait time is required for the CPU to return to the normal operation mode after the standby function has been released by the RESET signal (for details, refer to 7.2 Standby Mode Release ). The following two wait times can be selected: 217 /f X (21.8 ms when fX = 6.00 MHz; 31.3 ms when fX = 4.19 MHz) 215 /f X (5.46 ms when fX = 6.00 MHz; 7.81 ms when fX = 4.19 MHz) The µ PD75P3116 does not have a mask option and its wait time is fixed to 215/f X . 358 CHAPTER 11 INSTRUCTION SET The instruction set of the µPD753108 is based on the instruction set of the 75X Series and therefore, maintains compatibility with the 75X Series, but has some improved features. They are: (1) Bit manipulation instructions for various applications (2) Efficient 4-bit manipulation instructions (3) 8-bit manipulation instructions comparable to those of 8-bit microcontrollers (4) GETI instruction reducing program size (5) String-effect and base number adjustment instructions enhancing program efficiency (6) Table reference instructions ideal for successive reference (7) 1-byte relative branch instruction (8) Easy-to-understand, well-organized NEC’s standard mnemonics For the addressing modes applicable to data memory manipulation and the register banks valid for instruction execution, refer to section 3.2 Bank Configuration of General-Purpose Registers. 11.1 Unique Instructions This section describes the unique instructions of the µPD753108’s instruction set. 11.1.1 GETI instruction The GETI instruction converts the following instructions into 1-byte instructions: (a) Subroutine call instruction to 16 Kbytes space (0000H to 3FFFH) (b) Branch instruction to 16 Kbytes space (0000H to 3FFFH) (c) Any 2-byte, 2-machine cycle instruction (except BRCB and CALLF instructions) (d) Combination of two 1-byte instructions The GETI instruction references a table at addresses 0020H through 007FH of the program memory and executes the referenced 2-byte data as an instruction of (a) to (d). Therefore, 48 types of instructions can be converted into 1-byte instructions. If instructions that are frequently used are converted into 1-byte instructions by using this GETI instruction, the number of bytes of the program can be substantially decreased. 359 CHAPTER 11 INSTRUCTION SET 11.1.2 Bit manipulation instruction The µ PD753108 has reinforced bit test, bit transfer, and bit Boolean (AND, OR, and XOR) instructions, in addition to the ordinary bit manipulation (set and clear) instructions. The bit to be manipulated is specified in the bit manipulation addressing mode. Three types of bit manipulation addressing modes can be used. The bits manipulated in each addressing mode are shown in Table 11-1. Table 11-1. Types of Bit Manipulation Addressing Modes and Specification Range Addressing fmem.bit Peripheral Hardware That Can Be Manipulated RBE, MBE, IST1, IST0, SCC, IE ×××, IRQ ××× PORT0 to 3, 5, 6, 8, 9 pmem.@L @H + mem.bit BSB0 to 3, PORT0 to 3, 5, 6, 8, 9 All peripheral hardware units that can be manipulated bit-wise Addressing Range of Bit That Can Be Manipulated FB0H through FBFH FF0H through FFFH FC0H through FFFH All bits of memory bank specified by MB that can be manipulated bit-wise Remarks 1. ××× : 0, 1, 2, 4, BT, T0, T1, T2, W, CSI 2. MB = MBE•MBS 11.1.3 String-effect instruction The µ PD753108 has the following two types of string-effect instructions: (a) MOV A, #n4 or MOV XA, #n8 (b) MOV HL, #n8 “String effect” means locating these two types of instructions at contiguous addresses. Example A0 A1 XA7 : MOV : MOV : MOV A, #0 A, #1 XA, #07 When string-effect instructions are arranged as shown in this example, and if the address executed first is A0, the two instructions following this address are replaced with the NOP instructions. If the address executed first is A1, the following one instruction is replaced with the NOP instruction. In other words, only the instruction that is executed first is valid, and all the string-effect instructions that follow are processed as NOP instructions. By using these string-effect instructions, constants can be efficiently set to the accumulator (A register or register pair XA) and data pointer (register pair HL). 360 CHAPTER 11 INSTRUCTION SET 11.1.4 Base number adjustment instruction Some application requires that the result of addition or subtraction of 4-bit data (which is carried out in binary number) be converted into a decimal number or into a number with a base of 6, such as time. Therefore, the µPD753108 is provided with base number adjustment instructions that adjusts the result of addition or subtraction of 4-bit data into a number with any base. (a) Base adjustment of result of addition Where the base number to which the result of addition executed is to be adjusted is m, the contents of the accumulator and memory (HL) are added in the following combination, and the result is adjusted to a number with a base of m: ADDS ADDC ADDS A, #16–m A, @HL A, #m ; A, CY ← A + (HL) + CY Occurrence of an overflow is indicated by the carry flag. If a carry occurs as a result of executing the ADDC A, @HL instruction, the ADDS A, #n4 instruction is skipped. If a carry does not occur, the ADDS A, #n4 instruction is executed. At this time, however, the skip function of the instruction is disabled, and the following instruction is not skipped even if a carry occurs as a result of addition. Therefore, a program can be written after the ADDS A, #n4 instruction. Example To add accumulator and memory in decimal ADDS A, #6 ADDC A, @HL ADDS A, #10 . . . (b) Base adjustment of result of subtraction Where the base number into which the result of subtraction executed is to be adjusted is m, the contents of memory (HL) are subtracted from those of the accumulator in the following combination, and the result of subtraction is adjusted to a number with a base of m: SUBC A, @HL ADDS A, #m Occurrence of an underflow is indicated by the carry flag. If a borrow does not occur as a result of executing the SUBC A, @HL instruction, the following ADDS A, #n4 instruction is skipped. If a borrow occurs, the ADDS A, #n4 instruction is executed. At this time, the skip function of this instruction is disabled, and the following instruction is not skipped, even if a carry occurs as a result of addition. Therefore, a program can be written after the ADDS A, #n4 instruction. ; A, CY ← A + (HL) + CY 361 CHAPTER 11 INSTRUCTION SET 11.1.5 Skip instruction and number of machine cycles required for skipping The instruction set of the µ PD753108 configures a program where instructions may be or may not be skipped if a given condition is satisfied. If a skip condition is satisfied when a skip instruction is executed, the instruction next to the skip instruction is skipped and the instruction after the next is executed. When a skip occurs, the number of machine cycles required for skipping is: (a) If the instruction that follows the skip instruction (i.e., the instruction to be skipped) is a 3-byte instruction (BR !addr, BRA !addr1, CALL !addr, or CALLA !addr1 instruction): 2 machine cycles (b) Instruction other than (a): 1 machine cycle 362 CHAPTER 11 INSTRUCTION SET 11.2 Instruction Sets and their Operations (1) Expression formats and description methods of operands The operand is described in the operand column of each instruction in accordance with the description method for the operand expression format of the instruction. For details, refer to RA75X ASSEMBLER PACKAGE USER’S MANUAL — LANGUAGE (U12385E). If there are several elements, one of them is selected. Capital letters and the + and – symbols are key words and are described as they are. For immediate data, appropriate numbers and labels are described. Instead of the labels such as mem, fmem, pmem, and bit, the symbols of the registers shown in Figure 3-7 can be described. However, there are restrictions in the labels that can be described for fmem and pmem. For details, see Table 3-1 Addressing Mode and Figure 3-7 µPD753108 I/O Map. Expression Format reg reg1 rp rp1 rp2 rp' rp'1 rpa rpa1 n4 n8 mem bit fmem pmem addr Description Method X, A, B, C, D, E, H, L X, B, C, D, E, H, L XA, BC, BC, XA, BC, DE, HL DE, HL DE BC, DE, HL, XA', BC', DE', HL' BC, DE, HL, XA', BC', DE', HL' HL, HL+, HL–, DE, DL DE, DL 4-bit immediate data or label 8-bit immediate data or label 8-bit immediate data or label Note 2-bit immediate data or label FB0H-FBFH, FF0H-FFFH immediate data or label FC0H-FFFH immediate data or label 000H-FFFH immediate data or label ( µ PD753104) 0000H-17FFH immediate data or label ( µPD753106) 0000H-1FFFH immediate data or label ( µPD753108) 0000H-3FFFH immediate data or label ( µPD7P3116) 000H-FFFH immediate data or label ( µ PD753104) 0000H-17FFH immediate data or label ( µPD753106) 0000H-1FFFH immediate data or label ( µPD753108) 0000H-3FFFH immediate data or label ( µPD75P3116) 12-bit immediate data or label 11-bit immediate data or label 20H-7FH immediate data (where bit 0 = 0) or label PORT0-PORT3, PORT5, PORT6, PORT8, PORT9 IEBT, IET0-IET2, IE0-IE2, IE4, IECSI, IEW RB0-RB3 MB0, MB1, MB15 addr1 caddr faddr taddr PORTn IE ××× RBn MBn Note mem can be only used for even address in 8-bit data processing. 363 CHAPTER 11 INSTRUCTION SET (2) Legend in explanation of operation A B C D E H L X XA BC DE HL XA’ BC’ DE’ HL’ PC SP CY PSW MBE RBE PORTn IME IPS IE ××× RBS MBS PCC . ( ××) ×× H : A register; 4-bit accumulator : B register : C register : D register : E register : H register : L register : X register : XA register pair; 8-bit accumulator : BC register pair : DE register pair : HL register pair : XA’ expanded register pair : BC’ expanded register pair : DE’ expanded register pair : HL’ expanded register pair : Program counter : Stack pointer : Carry flag; bit accumulator : Program status word : Memory bank enable flag : Register bank enable flag : Port n (n = 0 to 3, 5, 6, 8, 9) : Interrupt master enable flag : Interrupt priority selection register : Interrupt enable flag : Register bank selection register : Memory bank selection register : Processor clock control register : Separation between address and bit : The contents addressed by ×× : Hexadecimal data 364 CHAPTER 11 INSTRUCTION SET (3) Explanation of symbols under addressing area column *1 *2 *3 MB = MBE • MBS (MBS = 0, 1, 15) MB = 0 MBE = 0 : MB = 0 (00H-7FH) MB = 15 (F80H-FFFH) MBE = 1 : MB = MBS (MBS = 0, 1, 15) MB = 15, fmem = FB0H-FBFH, FF0H-FFFH MB = 15, pmem = FC0H-FFFH Data memory addressing *4 *5 *6 µ PD753104 µ PD753106 µ PD753108 µ PD75P3116 addr = 000H-FFFH addr = 0000H-17FFH addr = 0000H-1FFFH addr = 0000H-3FFFH *7 addr = (Current PC) – 15 to (Current PC) – 1 (Current PC) + 2 to (Current PC) + 16 addr1 = (Current PC) – 15 to (Current PC) – 1 (Current PC) + 2 to (Current PC) + 16 *8 µ PD753104 µ PD753106 µ PD753108 µ PD75P3116 caddr = 000H-FFFH caddr = 0000H-0FFFH (PC 12 = 0) or 1000H-17FFH (PC 12 = 1) caddr = 0000H-0FFFH (PC 12 = 0) or 1000H-1FFFH (PC 12 = 1) caddr = 0000H-0FFFH (PC 13, 12 = 00B) or 1000H-1FFFH (PC 13, 12 = 01B) or 2000H-2FFFH (PC 13, 12 = 10B) or 3000H-3FFFH (PC 13, 12 = 11B) Program memory addressing *9 *10 *11 faddr = 0000H-07FFH taddr = 0020H-007FH µ PD753104 µ PD753106 µ PD753108 µ PD75P3116 addr1 = 000H-FFFH (Only in Mk II mode) addr1 = 0000H-17FFH (Only in Mk II mode) addr1 = 0000H-1FFFH (Only in Mk II mode) addr1 = 0000H-3FFFH (Only in Mk II mode) Remarks 1. MB indicates memory bank that can be accessed. 2. In *2, MB = 0 independently of how MBE and MBS are set. 3. In *4 and *5, MB = 15 independently of how MBE and MBS are set. 4. *6 to *11 indicate the areas that can be addressed. 365 CHAPTER 11 INSTRUCTION SET (4) Explanation of number of machine cycles column S denotes the number of machine cycles required by skip operation when a skip instruction is executed. The value of S varies as follows. • When no skip is made ......................................................................... S = 0 • When the skipped instruction is a 1- or 2-byte instruction ............... S = 1 • When the skipped instruction is a 3-byte instructionNote ................. S = 2 Note 3-byte instruction: BR !addr, BRA !addr1, CALL !addr or CALLA !addr1 instruction Caution The GETI instruction is skipped in one machine cycle. One machine cycle is equal to one cycle of CPU clock (= tCY); time can be selected from among four types by setting PCC (See Figure 5-12 Processor Clock Control Register Format). 366 CHAPTER 11 INSTRUCTION SET Instruction Group Transfer Mnemonic Operand Number of Bytes 1 2 2 2 2 1 1 1 1 2 1 2 2 2 2 2 2 2 2 2 1 1 1 1 2 2 2 1 2 Number of Machine Cycles 1 2 2 2 2 1 2+S 2+S 1 2 1 2 2 2 2 2 2 2 2 2 1 2+S 2+S 1 2 2 2 1 2 A ← n4 reg1 ← n4 XA ← n8 HL ← n8 rp2 ← n8 A ← (HL) Operation Addressing Skip Condition Area String effect A MOV A, #n4 reg1, #n4 XA, #n8 HL, #n8 rp2, #n8 A, @HL A, @HL+ A, @HL– A, @rpa1 XA, @HL @HL, A @HL, XA A, mem XA, mem mem, A mem, XA A, reg XA, rp' reg1, A rp'1, XA String effect A String effect B *1 *1 *1 *2 *1 *1 *1 *3 *3 *3 *3 L=0 L = FH A ← (HL), then L ← L + 1 A ← (HL), then L ← L – 1 A ← (rpa1) XA ← (HL) (HL) ← A (HL) ← XA A ← (mem) XA ← (mem) (mem) ← A (mem) ← XA A ← reg XA ← rp' reg1 ← A rp'1 ← XA A ↔ (HL) A ↔ (HL), then L ← L + 1 A ↔ (HL), then L ← L – 1 A ↔ (rpa1) XA ↔ (HL) A ↔ (mem) XA ↔ (mem) A ↔ reg1 XA ↔ rp' XCH A, @HL A, @HL+ A, @HL– A, @rpa1 XA, @HL A, mem XA, mem A, reg1 XA, rp' *1 *1 *1 *2 *1 *3 *3 L=0 L = FH 367 CHAPTER 11 INSTRUCTION SET Instruction Group Table reference Mnemonic Operand Number of Bytes 1 Number of Machine Cycles 3 Operation • µPD753104 XA ← (PC 11–8 + DE) ROM • µPD753106, 753108 XA ← (PC 12–8 + DE) ROM • µPD75P3116 XA ← (PC 13–8 + DE) ROM Addressing Skip Condition Area MOVT XA, @PCDE XA, @PCXA 1 3 • µPD753104 XA ← (PC 11–8 + XA) ROM • µPD753106, 753108 XA ← (PC 12–8 + XA) ROM • µPD75P3116 XA ← (PC 13–8 + XA) ROM XA, @BCDE XA, @BCXA Bit transfer MOV1 CY, fmem.bit CY, pmem.@L CY, @H+mem.bit fmem.bit, CY pmem.@L, CY @H+mem.bit, CY Operation ADDS A, #n4 XA, #n8 A, @HL XA, rp' rp'1, XA ADDC A, @HL XA, rp' rp'1, XA 1 1 2 2 2 2 2 2 1 2 1 2 2 1 2 2 3 3 2 2 2 2 2 2 1+S 2+S 1+S 2+S 2+S 1 2 2 XA ← (BCDE) ROMNote XA ← (BCXA) ROMNote CY ← (fmem.bit) CY ← (pmem 7–2 + L3–2.bit(L 1–0)) CY ← (H + mem 3–0.bit) (fmem.bit) ← CY (pmem7–2 + L3–2.bit(L 1–0)) ← CY (H + mem3–0.bit) ← CY A ← A + n4 XA ← XA + n8 A ← A + (HL) XA ← XA + rp' rp'1 ← rp'1 + XA A, CY ← A + (HL) + CY XA, CY ← XA + rp' + CY rp'1, CY ← rp'1 + XA + CY *6 *6 *4 *5 *1 *4 *5 *1 carry carry *1 carry carry carry *1 Note When the µ PD753104 is used, set 0 to the B register. When the µ PD753106 and 753108 are used, only low-order 1 bit is valid in B register. When the µ PD75P3116 is used, only low-order 2 bits are valid. 368 CHAPTER 11 INSTRUCTION SET Instruction Group Operation Mnemonic Operand Number of Bytes 1 2 2 1 2 2 2 1 2 2 2 1 2 2 2 1 2 2 1 2 1 1 2 2 1 2 2 2 1 2 2 2 Number of Machine Cycles 1+S 2+S 2+S 1 2 2 2 1 2 2 2 1 2 2 2 1 2 2 1 2 1+S 1+S 2+S 2+S 1+S 2+S 2+S 2+S 1+S 2+S 2+S 2+S A ← A – (HL) XA ← XA – rp' Operation Addressing Skip Condition Area *1 borrow borrow borrow *1 SUBS A, @HL XA, rp' rp'1, XA rp'1 ← rp'1 – XA A, CY ← A – (HL) – CY XA, CY ← XA – rp' – CY rp'1, CY ← rp'1 – XA – CY A ← A ∧ n4 A ← A ∧ (HL) XA ← XA ∧ rp' rp'1 ← rp'1 ∧ XA A ← A ∨ n4 A ← A ∨ (HL) XA ← XA ∨ rp' rp'1 ← rp'1 ∨ XA A ← A ∨ n4 A ← A ∨ (HL) XA ← XA ∨ rp' rp'1 ← rp'1 ∨ XA CY ← A 0, A 3 ← CY, A n–1 ← An A←A reg ← reg + 1 rp1 ← rp1 + 1 (HL) ← (HL) + 1 (mem) ← (mem) + 1 reg ← reg – 1 rp' ← rp' – 1 Skip if reg = n4 Skip if (HL) = n4 Skip if A = (HL) Skip if XA = (HL) Skip if A = reg Skip if XA = rp' *1 *1 *1 *1 *3 *1 *1 *1 SUBC A, @HL XA, rp' rp'1, XA AND A, #n4 A, @HL XA, rp' rp'1, XA OR A, #n4 A, @HL XA, rp' rp'1, XA XOR A, #n4 A, @HL XA, rp' rp'1, XA Accumulator RORC manipulation NOT Increment and decrement INCS A A reg rp1 @HL mem reg = 0 rp1 = 00H (HL) = 0 (mem) = 0 reg = FH rp' = FFH reg = n4 (HL) = n4 A = (HL) XA = (HL) A = reg XA = rp' DECS reg rp' Comparison SKE reg, #n4 @HL, #n4 A, @HL XA, @HL A, reg XA, rp' 369 CHAPTER 11 INSTRUCTION SET Instruction Group Mnemonic Operand Number of Bytes 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 Number of Machine Cycles 1 1 1+S 1 2 2 2 2 2 2 2 2 2+S 2+S 2+S 2+S CY ← 1 CY ← 0 Skip if CY = 1 CY ← CY (mem.bit) ← 1 (fmem.bit) ← 1 Operation Addressing Skip Condition Area Carry flag SET1 manipulation CLR1 SKT NOT1 Memory bit SET1 manipulation CY CY CY CY mem. bit fmem. bit pmem. @L @H+mem. bit CY = 1 *3 *4 *5 *1 *3 *4 *5 *1 *3 *4 *5 *1 (mem.bit) = 1 (fmem.bit) = 1 (pmem.@L) = 1 (@H+mem.bit) =1 (mem.bit) = 0 (fmem.bit) = 0 (pmem.@L) = 0 (@H+mem.bit) =0 (fmem.bit) = 1 (pmem.@L) = 1 (pmem7–2 + L3–2.bit(L 1–0)) ← 1 (H + mem3–0.bit) ← 1 (mem.bit) ← 0 (fmem.bit) ← 0 (pmem7–2 + L3–2.bit(L 1–0)) ← 0 (H + mem3–0.bit) ← 0 Skip if (mem.bit) = 1 Skip if (fmem.bit) = 1 Skip if (pmem 7–2 + L3–2.bit(L 1–0)) = 1 Skip if (H + mem3–0.bit) = 1 CLR1 mem. bit fmem. bit pmem. @L @H+mem. bit SKT mem. bit fmem. bit pmem. @L @H+mem. bit SKF mem. bit fmem. bit pmem. @L @H+mem. bit 2 2 2 2 2+S 2+S 2+S 2+S Skip if (mem.bit) = 0 Skip if (fmem.bit) = 0 Skip if (pmem 7–2 + L3–2.bit(L 1–0)) = 0 Skip if (H + mem3–0.bit) = 0 *3 *4 *5 *1 SKTCLR fmem. bit pmem. @L 2 2 2+S 2+S Skip if (fmem.bit) = 1 and clear Skip if (pmem 7–2 + L3–2.bit(L 1–0)) = 1 and clear Skip if (H + mem3–0.bit) = 1 and clear CY ← CY ∧ (fmem.bit) CY ← CY ∧ (pmem7–2 + L 3–2.bit(L1–0 )) CY ← CY ∧ (H + mem 3–0.bit) CY ← CY ∨ (fmem.bit) CY ← CY ∨ (pmem7–2 + L 3–2.bit(L1–0 )) CY ← CY ∨ (H + mem 3–0.bit) CY ← CY ∨ (fmem.bit) CY ← CY ∨ (pmem7–2 + L 3–2.bit(L1–0 )) CY ← CY ∨ (H + mem 3–0.bit) *4 *5 @H+mem. bit 2 2+S *1 (@H+mem.bit) =1 AND1 CY, fmem. bit CY, pmem. @L CY, @H+mem. bit 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 *4 *5 *1 *4 *5 *1 *4 *5 *1 OR1 CY, fmem. bit CY, pmem. @L CY, @H+mem. bit XOR1 CY, fmem. bit CY, pmem. @L CY, @H+mem. bit 370 CHAPTER 11 INSTRUCTION SET Instruction Group Branch Mnemonic Operand Number of Bytes — Number of Machine Cycles — Operation • µ PD753104 PC11–0 ← addr Select appropriate instruction from among BR !addr, BRCB !caddr and BR $addr according to the assembler being used. • µPD753106, 753108 PC12–0 ← addr Select appropriate instruction from among BR !addr, BRCB !caddr and BR $addr according to the assembler being used. • µ PD75P3116 PC13–0 ← addr Select appropriate instruction from among BR !addr, BRCB !caddr and BR $addr according to the assembler being used. Addressing Skip Condition Area *6 BRNote addr 371 CHAPTER 11 INSTRUCTION SET Instruction Group Branch Mnemonic Operand Number of Bytes — Number of Machine Cycles — Operation • µPD753104 PC11-0 ← addr Select appropriate instruction from among BR !addr, BRA !addr1, BRCB !caddr and BR $addr1 according to the assembler being used. • µPD753106, 753108 PC12–0 ← addr1 Select appropriate instruction from among BR !addr, BRA !addr1, BRCB !caddr and BR $addr1 according to the assembler being used. • µPD75P3116 PC13–0 ← addr1 Select appropriate instruction from among BR !addr, BRA !addr1, BRCB !caddr and BR $addr1 according to the assembler being used. Addressing Skip Condition Area *11 BRNote addr1 !addr 3 3 • µPD753104 PC11-0 ← addr • µPD753106, 753108 PC12–0 ← addr • µPD75P3116 PC13–0 ← addr *6 $addr 1 2 • µPD753104 PC11-0 ← addr • µPD753106, 753108 PC12–0 ← addr • µPD75P3116 PC13–0 ← addr *7 Note The above operations in the shaded boxes can be performed only in the Mk II mode. 372 CHAPTER 11 INSTRUCTION SET Instruction Group Branch Mnemonic Operand Number of Bytes 1 Number of Machine Cycles 2 • µ PD753104 PC11–0 ← addr1 Operation Addressing Skip Condition Area *7 BRNote 1 $addr1 • µPD753106, 753108 PC12–0 ← addr1 • µ PD75P3116 PC13–0 ← addr1 PCDE 2 3 • µ PD753104 PC11–0 ← PC11-8 + DE • µPD753106, 753108 PC12–0 ← PC12-8 + DE • µ PD75P3116 PC13–0 ← PC13-8 + DE PCXA 2 3 • µ PD753104 PC11–0 ← PC11-8 + XA • µPD753106, 753108 PC12–0 ← PC12-8 + XA • µ PD75P3116 PC13–0 ← PC13-8 + XA BCDE 2 3 • µ PD753104 PC11–0 ← BCDENote 2 • µPD753106, 753108 PC12–0 ← BCDENote 3 • µ PD75P3116 PC13–0 ← BCDENote 4 BCXA 2 3 • µ PD753104 PC11–0 ← BCXA Note 2 • µPD753106, 753108 PC12–0 ← BCXA Note 3 • µ PD75P3116 PC13–0 ← BCXA Note 4 *6 *6 Notes 1. The above operations in the shaded boxes can be performed only in the Mk II mode. The other operations can be performed only in the Mk I mode. 2. “0” must be set to B register. 3. Only low-order one bit is valid in B register. 4. Only low-order two bits are valid in B register. 373 CHAPTER 11 INSTRUCTION SET Instruction Group Branch Mnemonic Operand Number of Bytes 3 Number of Machine Cycles 3 • µPD753104 PC11–0 ← addr1 Operation Addressing Skip Condition Area *11 BRA Note !addr1 • µPD753106, 753108 PC12–0 ← addr1 • µPD75P3116 PC13–0 ← addr1 BRCB !caddr 2 2 • µPD753104 PC11–0 ← caddr 11–0 • µPD753106, 753108 PC12–0 ← PC12 + caddr 11–0 • µPD75P3116 PC13–0 ← PC13, Subroutine stack control CALLANote !addr1 3 3 *8 12 + caddr11–0 *11 • µPD753104 (SP – 2) ← ×, × , MBE, RBE (SP – 6) (SP – 3) (SP – 4) ← PC11–0 (SP – 5) ← 0, 0, 0, 0 PC11–0 ← addr1, SP ← SP – 6 • µPD753106, 753108 (SP – 2) ← ×, × , MBE, RBE (SP – 6) (SP – 3) (SP – 4) ← PC11–0 (SP – 5) ← 0, 0, 0, PC 12 PC12–0 ← addr1, SP ← SP – 6 • µPD75P3116 (SP – 2) ← ×, × , MBE, RBE (SP – 6) (SP – 3) (SP – 4) ← PC11–0 (SP – 5) ← 0, 0, PC13 , 12 PC13–0 ← addr1, SP ← SP – 6 Note The above operations in the shaded boxes can be performed only in the Mk II mode. The other operations can be performed only in the Mk I mode. 374 CHAPTER 11 INSTRUCTION SET Instruction Group Mnemonic Operand Number of Bytes 3 Number of Machine Cycles 3 Operation • µ PD753104 (SP – 3) ← MBE, RBE, 0, 0 (SP – 4) (SP – 1) (SP – 2) ← PC11–0 PC11–0 ← addr, SP ← SP – 4 • µPD753106, 753108 (SP – 3) ← MBE, RBE, 0, PC 12 (SP – 4) (SP – 1) (SP – 2) ← PC11–0 PC12–0 ← addr, SP ← SP – 4 • µ PD75P3116 (SP – 3) ← MBE, RBE, PC 13 , 12 (SP – 4) (SP – 1) (SP – 2) ← PC11–0 PC13–0 ← addr, SP ← SP – 4 Addressing Skip Condition Area *6 Subroutine CALLNote stack control !addr 4 • µ PD753104 (SP – 2) ← ×, × , MBE, RBE (SP – 6) (SP – 3) (SP – 4) ← PC11–0 (SP – 5) ← 0, 0, 0, 0 PC11–0 ← addr, SP ← SP – 6 • µPD753106, 753108 (SP – 2) ← ×, × , MBE, RBE (SP – 6) (SP – 3) (SP – 4) ← PC11–0 (SP – 5) ← 0, 0, 0, PC 12 PC12–0 ← addr, SP ← SP – 6 • µ PD75P3116 (SP – 2) ← ×, × , MBE, RBE (SP – 6) (SP – 3) (SP – 4) ← PC11–0 (SP – 5) ← 0, 0, PC13 , 12 PC13–0 ← addr, SP ← SP – 6 Note The above operations in the shaded boxes can be performed only in the Mk II mode. The other operations can be performed only in the Mk I mode. 375 CHAPTER 11 INSTRUCTION SET Instruction Group Mnemonic Operand Number of Bytes 2 Number of Machine Cycles 2 Operation • µPD753104 (SP – 3) ← MBE, RBE, 0, 0 (SP – 4) (SP – 1) (SP – 2) ← PC11–0 PC11–0 ← 0 + faddr, SP ← SP – 4 • µPD753106, 753108 (SP – 3) ← MBE, RBE, 0, PC 12 (SP – 4) (SP – 1) (SP – 2) ← PC11–0 PC12–0 ← 00 + faddr, SP ← SP – 4 • µPD75P3116 (SP – 3) ← MBE, RBE, PC 13 , 12 (SP – 4) (SP – 1) (SP – 2) ← PC11–0 PC13–0 ← 000 + faddr, SP ← SP – 4 Addressing Skip Condition Area *9 Subroutine CALLFNote stack control !faddr 3 • µPD753104 (SP – 2) ← ×, × , MBE, RBE (SP – 6) (SP – 3) (SP – 4) ← PC11–0 (SP – 5) ← 0, 0, 0, 0 PC11–0 ← 0 + faddr, SP ← SP – 6 • µPD753106, 753108 (SP – 2) ← ×, × , MBE, RBE (SP – 6) (SP – 3) (SP – 4) ← PC11–0 (SP – 5) ← 0, 0, 0, PC 12 PC12–0 ← 00 + faddr, SP ← SP – 6 • µPD75P3116 (SP – 2) ← ×, × , MBE, RBE (SP – 6) (SP – 3) (SP – 4) ← PC11–0 (SP – 5) ← 0, 0, PC13 , 12 PC13–0 ← 000 + faddr, SP ← SP – 6 Note The above operations in the shaded boxes can be performed only in the Mk II mode. The other operations can be performed only in the Mk I mode. 376 CHAPTER 11 INSTRUCTION SET Instruction Group Mnemonic Operand Number of Bytes 1 Number of Machine Cycles 3 Operation • µ PD753104 PC11–0 ← (SP) (SP + 3) (SP + 2) MBE, RBE, 0, 0 ← (SP + 1) SP ← SP + 4 • µPD753106, 753108 PC11–0 ← (SP) (SP + 3) (SP + 2) MBE, RBE, 0, PC12 ← (SP + 1) SP ← SP + 4 • µ PD75P3116 PC11–0 ← (SP) (SP + 3) (SP + 2) MBE, RBE, 0, PC13, 12 ← (SP + 1) SP ← SP + 4 • µ PD753104 ×, ×, MBE, RBE ← (SP + 4) 0, 0, 0, 0, ← (SP + 1) PC11–0 ← (SP) (SP + 3) (SP + 2) SP ← SP + 6 • µPD753106, 753108 ×, ×, MBE, RBE ← (SP + 4) MBE, 0, 0, PC12 ← (SP + 1) PC11–0 ← (SP) (SP + 3) (SP + 2) SP ← SP + 6 • µ PD75P3116 ×, ×, MBE, RBE ← (SP + 4) PC11–0 ← (SP) (SP + 3) (SP + 2) MBE, 0, PC13, 12 ← (SP + 1) SP ← SP + 6 Addressing Skip Condition Area Subroutine RETNote stack control Note The above operations in the shaded boxes can be performed only in the Mk II mode. The other operations can be performed only in the Mk I mode. 377 CHAPTER 11 INSTRUCTION SET Instruction Group Mnemonic Operand Number of Bytes 1 Number of Machine Cycles 3+S Operation • µPD753104 MBE, RBE, 0, 0 ← (SP + 1) PC11–0 ← (SP) (SP + 3) (SP + 2) SP ← SP + 4 then skip unconditionally • µPD753106, 753108 MBE, 0, 0, PC12 ← (SP + 1) PC11–0 ← (SP) (SP + 3) (SP + 2) SP ← SP + 4 then skip unconditionally • µPD75P3116 MBE, 0, PC13, 12 ← (SP + 1) PC11–0 ← (SP) (SP + 3) (SP + 2) SP ← SP + 4 then skip unconditionally • µPD753104 0, 0, 0, 0 ← (SP + 1) PC11–0 ← (SP) (SP + 3) (SP + 2) ×, ×, MBE, RBE ← (SP + 4) SP ← SP + 6 then skip unconditionally • µPD753106, 753108 0, 0, 0, PC12 ← (SP + 1) PC11–0 ← (SP) (SP + 3) (SP + 2) ×, ×, MBE, RBE ← (SP + 4) SP ← SP + 6 then skip unconditionally • µPD75P3116 ×, ×, MBE, RBE ← (SP + 4) PC11–0 ← (SP) (SP + 3) (SP + 2) 0, 0, PC 13, 12 ← (SP + 1) SP ← SP + 6 then skip unconditionally Addressing Skip Condition Area Unconditional Subroutine RETS Note stack control Note The above operations in the shaded boxes can be performed only in the Mk II mode. The other operations can be performed only in the Mk I mode. 378 CHAPTER 11 INSTRUCTION SET Instruction Group Mnemonic Operand Number of Bytes 1 Number of Machine Cycles 3 Operation • µ PD753104 MBE, RBE, 0, 0 ← (SP + 1) PC11–0 ← (SP) (SP + 3) (SP + 2) PSW ← (SP + 4) (SP + 5) SP ← SP + 6 • µPD753106, 753108 MBE, RBE, 0, PC12 ← (SP + 1) PC11–0 ← (SP) (SP + 3) (SP + 2) PSW ← (SP + 4) (SP + 5) SP ← SP + 6 • µ PD75P3116 MBE, RBE, PC 13, 12 ← (SP + 1) PC11–0 ← (SP) (SP + 3) (SP + 2) PSW ← (SP + 4) (SP + 5) SP ← SP + 6 • µ PD753104 0, 0, 0, 0 ← (SP + 1) PC11–0 ← (SP) (SP + 3) (SP + 2) PSW ← (SP + 4) (SP + 5) SP ← SP + 6 • µPD753106, 753108 0, 0, 0, PC12 ← (SP + 1) PC11–0 ← (SP) (SP + 3) (SP + 2) PSW ← (SP + 4) (SP + 5) SP ← SP + 6 • µ PD75P3116 0, 0, PC 13, 12 ← SP + 1 PC11–0 ← (SP) (SP + 3) (SP + 2) PSW ← (SP + 4) (SP + 5) SP ← SP + 6 Addressing Skip Condition Area Subroutine RETINote stack control PUSH rp 1 1 (SP – 1) (SP – 2) ← rp SP ← SP – 2 (SP – 1) ← MBS, (SP – 2) ← RBS SP ← SP – 2 rp ← (SP + 1) (SP) SP ← SP + 2 MBS ← (SP + 1), RBS ← (SP) SP ← SP + 2 IME (IPS.3) ← 1 IE××× ← 1 IME (IPS.3) ← 0 IE××× ← 0 BS 2 2 POP rp 1 1 BS 2 2 Interrupt control EI IE××× DI IE××× 2 2 2 2 2 2 2 2 Note The above operations in the shaded boxes can be performed only in the Mk II mode. The other operations can be performed only in the Mk I mode. 379 CHAPTER 11 INSTRUCTION SET Instruction Group Input/output Mnemonic Operand Number of Bytes 2 2 2 2 2 2 1 Number of Machine Cycles 2 2 2 2 2 2 1 2 2 A ← PORTn Operation Addressing Skip Condition Area IN Note A, PORTn XA, PORTn (n = 0-3, 5, 6, 8, 9) (n = 8) XA ← PORTn + 1, PORTn PORTn ← A OUT Note PORTn, A PORTn, XA (n = 2, 3, 5, 6, 8, 9) (n = 8) PORTn + 1, PORTn ← XA Set HALT Mode (PCC.2 ← 1) Set STOP Mode (PCC.3 ← 1) No Operation RBS ← n MBS ← n CPU control HALT STOP NOP Special SEL RBn MBn 2 2 (n = 0-3) (n = 0, 1, 15) Note While the IN instruction and OUT instruction are being executed, the MBE must be set to 0 or 1 and MBS must be set to 15. 380 CHAPTER 11 INSTRUCTION SET Instruction Group Special Mnemonic Operand Number of Bytes 1 Number of Machine Cycles 3 Operation • µ PD753104 • When TBR instruction PC11–0 ← (taddr) 3–0 + (taddr + 1) • When TCALL instruction (SP – 4) (SP – 1) (SP – 2) ← PC11–0 (SP – 3) ← MBE, RBE, 0, 0 PC11–0 ← (taddr) 3–0 + (taddr + 1) SP ← SP – 4 • When instruction other than TBR and TCALL instructions (taddr) (taddr + 1) instruction is executed. • µ PD753106, 753108 • When TBR instruction PC12–0 ← (taddr) 4–0 + (taddr + 1) • When TCALL instruction (SP – 4) (SP – 1) (SP – 2) ← PC11–0 (SP – 3) ← MBE, RBE, 0, PC 12 PC12–0 ← (taddr) 4–0 + (taddr + 1) SP ← SP – 4 • When instruction other than TBR and TCALL instructions (taddr) (taddr + 1) instruction is executed. • µ PD75P3116 • When TBR instruction PC13–0 ← (taddr) 5–0 + (taddr + 1) • When TCALL instruction (SP – 4) (SP – 1) (SP – 2) ← PC11–0 (SP + 1) ← MBE, RBE, 0, PC 13, 12 PC13–0 ← (taddr) 5–0 + (taddr + 1) SP ← SP – 4 • When instruction other than TBR and TCALL instructions (taddr) (taddr + 1) instruction is executed. Addressing Skip Condition Area *10 GETINote taddr Depending on the reference instruction Depending on the reference instruction Depending on the reference instruction Note The TBR and TCALL instructions are the table definition assembler pseudo-instructions of the GETI instruction. 381 CHAPTER 11 INSTRUCTION SET Instruction Group Special Mnemonic Notes 1, 2 Operand Number of Bytes 1 Number of Machine Cycles 3 Operation • µ PD753104 • When TBR instruction PC11–0 ← (taddr) 3–0 + (taddr + 1) • When TCALL instruction (SP – 6) (SP – 3) (SP – 4) ← PC 11–0 (SP – 5) ← 0, 0, 0, 0 (SP – 2) ← ×, ×, MBE, RBE PC11–0 ← (taddr) 3–0 + (taddr + 1) SP ← SP – 6 • When instruction other than TBR and TCALL instructions (taddr) (taddr + 1) instruction is executed. • µ PD753106, 753108 • When TBR instruction PC12–0 ← (taddr) 4–0 + (taddr + 1) Addressing Skip Condition Area *10 GETI taddr 4 3 Depending on the reference instruction 4 • When TCALL instruction (SP – 6) (SP – 3) (SP – 4) ← PC 11–0 (SP – 5) ← 0, 0, 0, PC 12 (SP – 2) ← ×, ×, MBE, RBE PC12–0 ← (taddr) 4–0 + (taddr + 1) SP ← SP – 6 • When instruction other than TBR and TCALL instructions (taddr) (taddr + 1) instruction is executed. • µ PD75P3116 • When TBR instruction PC13–0 ← (taddr) 5–0 + (taddr + 1) Depending on the reference instruction 3 4 • When TCALL instruction (SP – 6) (SP – 3) (SP – 4) ← PC 11–0 (SP – 5) ← MBE, RBE, PC13 , 12 (SP – 2) ← ×, ×, MBE, RBE PC13–0 ← (taddr) 5–0 + (taddr + 1) SP ← SP – 6 • When instruction other than TBR and TCALL instructions (taddr) (taddr + 1) instruction is executed. Depending on the reference instruction 3 Notes 1. The TBR and TCALL instructions are the table definition assembler pseudo-instructions of the GETI instruction. 2. The above operations in the shaded boxes can be performed only in the Mk II mode. The other operations can be performed only in the Mk I mode. 382 CHAPTER 11 INSTRUCTION SET 11.3 Op Code of Each Instruction (1) Description of symbol of op code R2 R1 R0 000 001 010 011 100 101 110 111 reg A X L H E D C B reg P2 P1 P0 000 001 010 011 reg1 100 101 110 111 reg-pair XA XA’ HL HL’ DE DE’ BC BC’ rp’ rp’1 Q2 Q1 Q0 000 010 011 100 101 addressing @HL @HL + @HL – @DE @DL @rpa @rpa1 P2 P1 00 01 10 11 reg-pair XA HL DE BC rp1 rp2 rp N5 N2 N1 N0 0000 0010 0100 0101 0110 0111 1000 1100 1101 1110 IE××× IEBT IEW IET0 IECSI IE0 IE2 IE4 IET1 IET2 IE1 In : Dn : Bn : Nn : Tn : An : Sn : immediate data for n4 or n8 immediate data for mem immediate data for bit immediate data for n or IE××× immediate data for taddr × 1/2 immediate data for [relative address distance from branch destination address (2 – 16)] – 1 immediate data for 1’s complement of [relative address distance from branch destination address (15 – 1)] 383 CHAPTER 11 INSTRUCTION SET (2) Op code for bit manipulation addressing ∗1 in the operand field indicates the following three types: • fmem.bit • pmem.@L • @H+mem.bit The second byte ∗2 of the op code corresponding to the above addressing is as follows: ∗1 fmem. bit 1 1 pmem. @L @H+mem. bit 0 0 0 1 1 0 2nd Byte of Op Code B1 B1 0 B1 B0 B0 0 B0 F3 F3 G3 D3 F2 F2 G2 D2 F1 F1 G1 D1 F0 F0 G0 D0 Accessible Bit Bit of FB0H to FBFH that can be manipulated Bit of FF0H to FFFH that can be manipulated Bit of FC0H to FFFH that can be manipulated Bit of accessible memory bank that can be manipulated Bn : Fn : Gn : Dn : immediate data for bit immediate data for fmem (indicates low-order 4 bits of address) immediate data for pmem (indicates bits 5 to 2 of address) immediate data for mem (indicates low-order 4 bits of address) 384 CHAPTER 11 INSTRUCTION SET Op Code Instruction Mnemonic Operand B1 Transfer MOV A, #n4 reg1, #n4 rp, #n8 A, @rpa1 XA, @HL @HL, A @HL, XA A, mem XA, mem mem, A mem, XA A, reg XA, rp’ reg1, A rp’1, XA XCH A, @rpa1 XA, @HL A, mem XA, mem A, reg1 XA, rp’ Table reference MOVT XA, @PCDE XA, @PCXA XA, @BCDE XA, @BCXA Bit transfer MOV1 CY, ∗1 ∗1 , CY 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 1 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 1 0 1 1 1 1 0 0 1 0 0 1 1 1 1 1 1 0 0 0 1 0 1 1 1 1 1 0 1 0 0 0 0 1 0 1 1 0 0 0 0 0 0 0 1 1 1 0 1 0 0 0 1 1 1 0 1 1 1 1 1 1 I3 1 I2 0 I1 1 I0 0 I3 I7 I2 I6 I1 I5 I0 I4 1 R2 R1 R0 I3 I2 I1 I0 B2 B3 1 P2 P1 1 0 Q2 Q1 Q0 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 0 1 0 1 0 0 0 0 0 0 1 1 0 0 0 0 0 0 1 0 0 0 0 1 D7 D6 D5 D4 D3 D2 D1 D0 0 D7 D6 D5 D4 D3 D2 D1 0 1 D7 D6 D5 D4 D3 D2 D1 D0 0 D7 D6 D5 D4 D3 D2 D1 0 1 0 1 0 0 0 0 0 1 1 1 1 1 0 1 0 1 1 1 1 1 R2 R1 R0 1 P2 P1 P0 0 R2 R1 R0 0 P2 P1 P0 1 Q2 Q1 Q0 1 0 0 0 0 0 1 1 1 0 0 0 0 1 0 0 0 1 1 D7 D6 D5 D4 D3 D2 D1 D0 0 D7 D6 D5 D4 D3 D2 D1 0 1 R2 R1 R0 1 0 0 0 0 1 1 0 1 0 1 0 1 0 1 0 0 0 0 0 1 0 0 0 1 1 1 1 *2 *2 0 1 0 0 0 P2 P1 P0 385 CHAPTER 11 INSTRUCTION SET Op Code Instruction Mnemonic Operand B1 Operation ADDS A, #n4 XA, #n8 A, @HL XA, rp’ rp’1, XA ADDC A, @HL XA, rp’ rp’1, XA SUBS A, @HL XA, rp’ rp’1, XA SUBC A, @HL XA, rp’ rp’1, XA AND A, #n4 A, @HL XA, rp’ rp’1, XA OR A, #n4 A, @HL XA, rp’ rp’1, XA XOR A, #n4 A, @HL XA, rp’ rp’1, XA Accumulator manipulation RORC NOT A A 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 1 1 1 1 1 1 1 1 1 1 1 0 0 1 1 0 1 1 1 0 1 1 1 0 0 0 1 1 0 0 0 0 0 0 0 0 1 0 0 1 1 0 0 1 0 0 0 1 1 0 0 1 1 I3 1 0 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 0 1 1 1 0 1 1 1 1 I2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 I1 0 1 1 1 0 1 1 0 1 1 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 I0 1 0 0 0 1 0 0 0 0 0 0 0 0 1 0 0 0 1 0 0 0 1 0 0 0 0 1 0 1 0 1 1 1 1 1 1 1 0 0 1 1 1 1 1 P2 P1 P0 0 P2 P1 P0 1 1 0 0 0 1 1 1 0 0 0 1 1 P2 P1 P0 0 P2 P1 P0 I3 I2 I1 I0 1 1 0 0 0 1 0 0 0 1 1 0 1 P2 P1 P0 0 P2 P1 P0 I3 I2 I1 I0 1 1 0 1 1 0 1 1 1 1 1 1 1 P2 P1 P0 0 P2 P1 P0 I3 I2 I1 I0 1 1 1 1 1 1 0 0 1 P2 P1 P0 0 P2 P1 P0 1 1 1 1 0 0 1 1 1 P2 P1 P0 0 P2 P1 P0 1 1 1 1 0 0 0 0 1 P2 P1 P0 0 P2 P1 P0 I7 I6 I5 I4 I3 I2 I1 I0 B2 B3 386 CHAPTER 11 INSTRUCTION SET Op Code Instruction Mnemonic Operand B1 Increment/ decrement INCS reg rp1 @HL mem DECS reg rp’ Comparison SKE reg, #n4 @HL, #n4 A, @HL XA, @HL A, reg XA, rp’ Carry flag manipulation SET1 CLR1 SKT NOT1 Memory bit manipulation CLR1 SET1 CY CY CY CY mem. bit *1 mem. bit *1 SKT mem. bit *1 SKF mem. bit *1 SKTCLR AND1 OR1 XOR1 *1 CY, *1 CY, *1 CY, *1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 1 0 0 0 1 0 1 1 1 0 0 0 0 1 0 0 0 1 1 0 0 1 0 0 0 1 1 0 R2 R1 R0 1 P2 P1 0 1 0 0 0 0 1 1 0 0 0 0 0 0 1 0 B2 B3 0 D7 D6 D5 D4 D3 D2 D1 D0 1 R2 R1 R0 1 1 1 0 1 1 1 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 1 0 1 1 1 1 1 0 0 0 0 1 1 1 1 1 0 1 0 0 0 1 0 0 1 0 1 0 1 0 1 D7 D6 D5 D4 D3 D2 D1 D0 1 *2 0 0 0 0 0 1 0 0 0 1 0 0 1 0 0 1 0 I3 0 1 I2 1 1 I1 1 0 I0 0 1 P 2 P 1 P0 0 R2 R1 R0 I3 I2 I1 I0 1 R2 R1 R0 1 P2 P1 P0 0 B1 B0 0 0 0 1 1 0 B1 B0 0 0 0 1 1 0 D7 D6 D5 D4 D3 D2 D1 D0 0 *2 0 B1 B0 0 0 1 1 1 1 D7 D6 D5 D4 D3 D2 D1 D0 1 *2 0 B1 B0 0 0 0 0 0 0 1 0 1 1 1 1 1 0 0 1 1 1 1 1 1 0 D7 D6 D5 D4 D3 D2 D1 D0 0 1 0 0 0 *2 *2 *2 *2 *2 387 CHAPTER 11 INSTRUCTION SET Op Code Instruction Mnemonic Operand B1 Branch BR ! addr (+16) to (+2) $ addr (–1) to (–15) PCDE PCXA BCDE BCXA BRA BRCB Subroutine stack control CALLA CALL CALLF RET RETS RETI PUSH rp BS POP rp BS I/O IN A, PORTn XA, PORTn OUT PORTn, A PORTn, XA Interrupt control DI IE××× CPU control HALT STOP NOP Special SEL RBn MBn GETI taddr EI IE××× ! addr1 ! caddr ! addr1 ! addr ! faddr 1 1 1 0 1 1 0 1 1 0 1 1 1 0 1 0 1 1 1 1 1 1 1 1 1 1 1 0 1 1 0 1 0 0 0 0 0 1 0 0 1 1 1 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0 0 1 0 1 1 0 1 1 1 0 0 0 0 1 1 0 0 0 0 0 0 0 0 1 0 0 1 S3 S2 S1 S0 1 1 0 1 1 1 1 0 0 0 0 0 0 1 0 1 0 0 1 1 1 1 1 1 1 1 0 1 1 1 1 0 1 0 1 1 0 1 1 0 1 0 0 1 0 0 1 1 1 1 0 0 1 faddr 1 1 0 1 1 0 0 1 0 0 0 0 0 0 1 1 1 1 1 0 0 0 caddr addr addr 0 0 0 0 0 0 1 addr1 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 1 0 0 0 1 0 0 1 0 1 1 0 0 B2 addr B3 0 A3 A2 A1 A0 1 P2 P1 1 1 0 0 1 0 0 0 0 0 1 1 1 1 P2 P1 0 1 0 0 0 0 1 1 1 1 1 1 0 1 1 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 0 0 1 1 0 1 0 1 1 0 0 1 1 0 1 1 0 0 0 0 1 0 0 0 0 N1 N0 0 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 0 0 1 1 1 1 1 0 0 1 1 0 1 N3 N2 N1 N0 1 N3 N2 N1 N0 1 N3 N2 N1 N0 1 N3 N2 N1 N0 1 0 0 1 0 0 N5 1 0 1 1 1 N2 N1 N0 0 0 1 0 0 N5 1 0 0 1 1 0 1 1 N2 N1 N0 0 0 0 0 1 1 1 1 1 N3 N2 N1 N0 0 T5 T4 T3 T2 T1 T0 388 CHAPTER 11 INSTRUCTION SET 11.4 Instruction Function and Application This section describes the functions and applications of the respective instructions. The instructions that can be used and the functions of the instructions differ between the Mk I and Mk II modes of the µ PD753104, 753106, 753108, and 75P3116. Read the descriptions on the following pages according to the following guidance: How to read : This instruction can be used commonly to all the following: µPD753104 µPD753106 µPD753108 µPD75P3116 I II I/II : This instruction can be used only in the Mk I mode of the µPD753104, 753106, 753108, and 75P3116. : This instruction can be used only in the Mk II mode of the µ PD753104, 753106, 753108, and 75P3116. : This instruction can be used commonly in the Mk I and Mk II modes of the µ PD753104, 753106, 753108, and 75P3116, but the function may differ between the Mk I and Mk II modes. In the Mk I mode, read the description under the heading [Mk I mode]. In the Mk II mode, read the description under the heading [Mk II mode]. Remark In this section, it is assumed that the 13-bit program counter of the µPD753106 and µPD753108 is used. Note that the program counter of the µ PD753104 is 12 bits wide, and that of the µ PD75P3116 is 14 bits wide. In Mk I and Mk II modes 389 CHAPTER 11 INSTRUCTION SET 11.4.1 Transfer instructions MOV A, #n4 Function: A ← n4 n4 = I3-0 : 0-FH Transfers 4-bit immediate data n4 to the A register (4-bit accumulator). This instruction has a string effect (group A). Therefore, if this instruction is followed by another MOV A, #n4 or MOV XA, #n8, the following instruction will be processed as a NOP instruction. Application example (1) To set 0BH to the accumulator MOV A, #0BH (2) To select data output to port 3 from 0 to 2 A0: A1: A2: MOV A, #0 MOV A, #1 MOV A, #2 OUT PORT3, A MOV reg1, #n4 Function: reg1 ← n4 n4 = I3-0 0-FH Transfers 4-bit immediate data n4 to A register reg1 (X, H, L, D, E, B, or C). MOV XA, #n8 Function: XA ← n8 n8 = I7-0 : 00H-FFH Transfers 8-bit immediate data n8 to register pair XA. This instruction has a string effect, and if two or more of this instruction are executed in succession or if this instruction is followed by the MOV A, #n4 instruction, the instruction following this instruction is treated as NOP. MOV HL, #n8 Function: HL ← n8 n8 = I7-0: 00H-FFH Transfers 8-bit immediate data n8 to register pair HL. This instruction has a string effect. If two or more of this instructions are executed in succession, those that follow the first instruction are treated as NOP. MOV rp2, #n8 Function: rp2 ← n8 n8 = I7-0 : 00H-FFH Transfers 8-bit immediate data n8 to register pair rp2 (BC, DE). 390 CHAPTER 11 INSTRUCTION SET MOV A, @HL MOV A, @HL+ MOV A, @HL– MOV A, @rpa1 Function: A ← (Register pair specified with an operand) when register pair = HL+ : skip if L = 0 when register pair = HL– : skip if L = FH Transfers the contents of the data memory addressed by a register pair (HL, HL+, HL–, DE, or DL) to the A register. If autoincrement (HL+) is specified as a register pair, the contents of the L register are automatically incremented by one after the data has been transferred. If the contents of the L register become 0 as a result, the next one instruction is skipped. If autodecrement (HL–) is specified as a register pair, the contents of the L register are automatically decremented by one after the data has been transferred. If the contents of the L register become FH as a result, the next one instruction is skipped. MOV XA, @HL Function: A ← (HL), X ← (HL + 1) Transfers the contents of the data memory addressed by register pair HL to the A register, and the contents of the next memory address to the X register. If the contents of the L register are an odd number, an address whose least significant bit is ignored is transferred. Application example To transfer the data at addresses 3EH and 3FH to register pair XA MOV HL, #3EH MOV XA, @HL MOV @HL, A Function: (HL) ← A Transfers the contents of the A register to the data memory addressed by register pair HL. 391 CHAPTER 11 INSTRUCTION SET MOV @HL, XA Function: (HL) ← A, (HL + 1) ← X Transfers the contents of the A register to the data memory addressed by register pair HL, and the contents of the X register to the next memory address. However, if the contents of the L register are an odd number, an address whose least significant bit is ignored is transferred. MOV A, mem Function: A ← (mem) mem = D 7-0: 00H-FFH Transfers the contents of the data memory addressed by 8-bit immediate data mem to the A register. MOV XA, mem Function: A ← (mem), X ← (mem + 1) mem = D 7-0: 00H-FEH Transfers the contents of the data memory addressed by 8-bit immediate data mem to the A register and the contents of the next address to the X register. The address that can be specified by mem is an even address. Application example To transfer the data at addresses 40H and 41H to register pair XA MOV XA, 40H MOV mem, A Function: (mem) ← A mem = D 7-0: 00H-FFH Transfers the contents of the A register to the data memory addressed by 8-bit immediate data mem. MOV mem, XA Function: (mem) ← A, (mem + 1) ← X mem = D7-0: 00H-FEH Transfers the contents of the A register to the data memory addressed by 8-bit immediate data mem and the contents of the X register to the next memory address. The address that can be specified by mem is an even address. 392 CHAPTER 11 INSTRUCTION SET MOV A, reg Function: A ← reg Transfers the contents of register reg (X, A, H, L, D, E, B, or C) to the A register. MOV XA, rp’ Function: XA ← rp’ Transfers the contents of register pair rp’ (XA, HL, DE, BC, XA’, HL’, DE’, or BC’) to register pair XA. Application example To transfer the data of register pair XA’ to register pair XA MOV XA, XA’ MOV reg1, A Function: reg1 ← A Transfers the contents of the A register to register reg1 (X, H, L, D, E, B, or C). MOV rp’1, XA Function: rp’1 ← XA Transfers the contents of register pair XA to register pair rp’1 (HL, DE, BC, XA’, HL’, DE’, or BC’). 393 CHAPTER 11 INSTRUCTION SET XCH A, @HL XCH A, @HL+ XCH A, @HL– XCH A, @rpa1 Function: A ↔ (Register pair specified with an operand) when register pair = HL+ : skip if L = 0 when register pair = HL– : skip if L = FH Exchanges the contents of the A register with the contents of the data memory addressed by a register pair (HL, HL+, HL–, DE, or DL). If autoincrement (HL+) is specified as a register pair, the contents of the L register are automatically incremented by one after the data have been exchanged. If the increment result is 0, the next one instruction is skipped. If autodecrement (HL–) is specified as a register pair, the contents of the L register are automatically decremented by one after the data have been exchanged. If the decrement result is FH, the next one instruction is skipped. Application example To exchange the data at data memory addresses 20H through 2FH with the data at addresses 30H through 3FH SEL MOV MOV LOOP: XCH XCH XCH BR MB0 D, #2 HL, #30H A, @HL A, @DL A, @HL+ LOOP ; A ↔ ( 3 ×) ; A ↔ ( 2 ×) ; A ↔ ( 3 ×) XCH XA, @HL Function: A ↔ (HL), X ↔ (HL + 1) Exchanges the contents of the A register with the contents of the data memory addressed by register pair HL, and the contents of the X register with the contents of the next address. If the contents of the L register are odd numbers, however, an address whose least significant bit is ignored is specified. XCH A, mem Function: A ↔ (mem) mem = D 7-0: 00H-FEH Exchanges the contents of the A register with the contents of the data memory addressed by 8-bit immediate data mem. 394 CHAPTER 11 INSTRUCTION SET XCH XA, mem Function: A ↔ (mem), X ↔ (mem + 1) mem = D 7-0: 00H-FEH Exchanges the contents of the A register with the data memory contents addressed by 8-bit immediate data mem, and the contents of the X register with the contents of the next memory address. The address that can be specified by mem is an even address. XCH A, reg1 Function: A ↔ reg1 Exchanges the contents of the A register with the contents of register reg1 (X, H, L, D, E, B, or C). XCH XA, rp’ Function: XA ↔ rp’ Exchanges the contents of register pair XA with the contents of register pair rp’ (XA, HL, DE, BC, XA’, HL’, DE’, or BC’). 395 CHAPTER 11 INSTRUCTION SET 11.4.2 Table reference instructions MOVT XA, @PCDE Function: µ PD753106 and µ PD753108 XA ← ROM (PC12-8 + DE) Transfers the low-order 4 bits of the table data in the program memory addressed to the A register when the low-order 8 bits (PC7-0 ) of the program counter (PC) are replaced with the contents of register pair DE, and the highorder 4 bits to the X register. The table address is determined by the contents of the program counter (PC) when this instruction is executed. The necessary data must be programmed to the table area in advance by using an assembler pseudo-instruction (DB instruction). The program counter is not affected by execution of this instruction. This instruction is useful for successively referencing table data. Example In the case of µPD753106 or 753108 Program memory 43 87 Table address PC12-8 D3-0 43 E3-0 0 7 0 Table data H Table data L 3 X 0 3 A 0 Remark The function described here applies to the µPD753106 and 753108 that has a 13-bit program counter. Note that the program counter of the µ PD753104 is 12 bits wide and that of the µ PD75P3116 is 14 bits wide. 396 CHAPTER 11 INSTRUCTION SET Caution The MOVT XA, @PCDE instruction usually references the table data in page where the instruction exists. If the instruction is at address ×× FFH, however, the table data in the page where the instruction exists is not referenced, but the table data in the next page is referenced. Program memory 7 Page 2 0 02FFH 0300H Page 3 a For example, if the MOV XA, @PCDE instruction is located at position a in the above figure, the table data in page 3, not page 2, specified by the contents of register pair DE is transferred to register pair XA. Application example To transfer the 16-byte data at program memory addresses ××F0H through ×× FFH to data memory addresses 30H through 4FH SUB: SEL MOV MOV LOOP: MOVT MOV INCS INCS INCS BR RET ORG DB ××F0H ××H, ×× H, ··· ; table data MB0 HL, #30H DE, #0F0H @HL, XA HL HL E LOOP ;E←E+1 ; HL ← 30H ; DE ← F0H ; (HL) ← XA ; HL ← HL + 2 XA, @PCDE ; XA ← table data 397 CHAPTER 11 INSTRUCTION SET MOVT XA, @PCXA Function: µ PD753106 and µ PD753108 XA ← ROM (PC12-8 + XA) Transfers the low-order 4 bits of the table data in the program memory addressed to the A register when the low-order 8 bits (PC7-0 ) of the program counter (PC) are replaced with the contents of register pair XA, and the highorder 4 bits to the X register. The table address is determined by the contents of the PC when this instruction is executed. The necessary data must be programmed to the table area in advance by using an assembler pseudo-instruction (DB instruction). The PC is not affected by execution of this instruction. Caution If an instruction exists at address ××FFH, the table data of the next page is transferred, in the same manner as MOVT XA, @PCDE. Remark The function described here applies to the µPD753106 and 753108 that has a 13-bit program counter. Note that the program counter of the µ PD753104 is 12 bits wide and that of the µ PD75P3116 is 14 bits wide. 398 CHAPTER 11 INSTRUCTION SET MOVT XA, @BCDE Function: µ PD75106 and 753108 XA ← ROM (B0 + CDE) Transfers the low-order 4 bits of the table data (8-bit) in the program memory addressed by the least significant bit of register B and the contents of registers C, D, and E, to the A register, and the high-order 4 bits to the X register. The necessary data must be programmed to the table area in advance by using an assembler pseudo-instruction (DB instruction). The PC is not affected by execution of this instruction. 12 B0 11 C 87 D 43 E 0 Table data H Table data L 3 X 0 3 A 0 MOVT XA, @BCXA Function: µ PD753106 and 753108 XA ← ROM (B0 + CXA) Transfers the low-order 4 bits of the table data (8-bit) in the program memory addressed by the least significant bit of register B and the contents of registers C, X, and A, to the A register, and the high-order 4 bits to the X register. The necessary data must be programmed to the table area in advance by using an assembler pseudo-instruction (DB instruction). The PC is not affected by execution of this instruction. 12 B0 11 C 87 X 43 A 0 Table data H Table data L 3 X 0 3 A 0 Remark The function described here applies to the µPD753106 and 753108 that has a 13-bit program counter. Note that the program counter of the µ PD753104 is 12 bits wide and that of the µ PD75P3116 is 14 bits wide. 399 CHAPTER 11 INSTRUCTION SET 11.4.3 Bit transfer instructions MOV1 CY, fmem. bit MOV1 CY, pmem. @L MOV1 CY, @H+mem. bit Function: CY ← (bit specified by operand) Transfers the contents of the data memory addressed in the bit manipulating addressing mode (fmem. bit, pmem. @L, or @H+mem. bit) to the carry flag (CY). MOV1 fmem. bit, CY MOV1 pmem. @L, CY MOV1 @H+mem. bit, CY Function: (bit specified by operand) ← CY Transfers the contents of the carry flag (CY) to the data memory bit addressed in the bit manipulation addressing mode (fmem. bit, pmem. @L, or @H+mem. bit). Application example To output the flag of bit 3 at data memory address 3FH to the bit 2 of port 3 FLAG SEL MOV MOV1 MOV1 EQU 3FH.3 MB0 H, #FLAG SHR 6 ; H ← high-order 4 bits of FLAG CY, @H+FLAG PORT3. 2, CY ; CY ← FLAG ; P32 ← CY 400 CHAPTER 11 INSTRUCTION SET 11.4.4 Operation instructions ADDS A, #n4 Function: A ← A + n4; Skip if carry. n4 = l 3-0: 0-FH Adds 4-bit immediate data n4 to the contents of the A register. If a carry occurs as a result, the next instruction is skipped. The carry flag is not affected. If this instruction is used in combination with ADDC A, @HL or SUBC A, @HL instruction, it can be used as a base number adjustment instruction (refer to section 11.1.4 Base number adjustment instruction ). ADDS XA, #n8 Function: XA ← XA + n8; Skip if carry. n8 = I7-0 : 00H-FFH Adds 8-bit immediate data n8 to the contents of register pair XA. If a carry occurs as a result, the next instruction is skipped. The carry flag is not affected. ADDS A, @HL Function: A ← A + (HL); Skip if carry. Adds the contents of the data memory addressed by register pair HL to the contents of the A register. If a carry occurs as a result, the next instruction is skipped. The carry flag is not affected. ADDS XA, rp’ Function: XA ← XA + rp’; Skip if carry. Adds the contents of register pair rp’ (XA, HL, DE, BC, XA’, HL’, DE’, or BC’) to the contents of register pair XA. If a carry occurs as a result, the next instruction is skipped. The carry flag is not affected. 401 CHAPTER 11 INSTRUCTION SET ADDS rp’1, XA Function: rp’ ← rp’1 + XA; Skip if carry. Adds the contents of register pair XA to register pair rp’1 (HL, DE, BC, XA’, HL’, DE’, or BC’). If a carry occurs as a result, the next instruction is skipped. The carry flag is not affected. Application example To shift a register pair to the left MOV ADDS NOP XA, rp’1 rp’1, XA ADDC A, @HL Function: A, CY ← A + (HL) + CY Adds the contents of the data memory addressed by register pair HL to the contents of the A register, including the carry flag. If a carry occurs as a result, the carry flag is set; if not, the carry flag is reset. If the ADDS A, #n4 instruction is placed following this instruction, and if a carry occurs as a result of executing this instruction, the ADDS A, #n4 instruction is skipped. If a carry does not occur, the ADDS A, #n4 instruction is executed, and a function that disables the skip function of the ADDS A, #n4 instruction is effected. Therefore, these instructions can be used in combination for base number adjustment (refer to section 11.1.4 Base number adjustment instruction). ADDC XA, rp’ Function: XA, CY ← XA + rp’ + CY Adds the contents of register pair rp’ (XA, HL, DE, BC, XA’, HL’, DE’, or BC’) to the contents of register pair XA, including the carry. If a carry occurs as a result, the carry flag is set; if not, the carry flag is reset. 402 CHAPTER 11 INSTRUCTION SET ADDC rp’1, XA Function: rp’1, CY ← rp’1 + XA + CY Adds the contents of register pair XA to the contents of register pair rp’1 (HL, DE, BC, XA’, HL’, DE’, or BC’), including the carry flag. If a carry occurs as a result, the carry flag is set; if not, the carry flag is reset. SUBS A, @HL Function: A ← A – (HL); Skip if borrow Subtracts the contents of the data memory addressed by register pair HL from the contents of the A register, and sets the result to the A register. If a borrow occurs as a result, the next instruction is skipped. The carry flag is not affected. SUBS XA, rp’ Function: XA ← XA – rp’; Skip if borrow Subtracts the contents of register pair rp’ (XA, HL, DE, BC, XA’, HL’, DE’, or BC’) from the contents of register pair XA, and sets the result to register pair XA. If a borrow occurs as a result, the next instruction is skipped. The carry flag is not affected. Application example To compare specified data memory contents with the contents of a register pair MOV SUBS XA, mem XA, rp’ ; (mem) ≥ rp’ ; (mem) < rp’ 403 CHAPTER 11 INSTRUCTION SET SUBS rp’1, XA Function: rp’ ← rp’1 + XA; Skip if borrow Subtracts the contents of register pair XA from register pair rp’1 (HL, DE, BC, XA’, HL’, DE’, or BC’), and sets the result to specified register pair rp’1. If a borrow occurs as a result, the next instruction is skipped. The carry flag is not affected. SUBC A, @HL Function: A, CY ← A – (HL) – CY Subtracts the contents of the data memory addressed by register pair HL to the contents from the A register, including the carry flag, and sets the result to the A register. If a borrow occurs as a result, the carry flag is set; if not, the carry flag is reset. If an ADDS A, #n4 instruction is placed following this instruction, and if a borrow does not occur as a result of executing this instruction, the ADDS A, #n4 instruction is skipped. If a borrow occurs, the ADDS A, #n4 instruction is executed, and a function that disables the skip function of the ADDS A, #n4 instruction is effected. Therefore, these instructions can be used in combination for base number adjustment (refer to section 11.1.4 Base number adjustment instruction). SUBC XA, rp’ Function: XA, CY ← XA – rp’ – CY Subtracts the contents of register pair rp’ (XA, HL, DE, BC, XA’, HL’, DE’, or BC’) from the contents of register pair XA, including the carry, and sets the result to register pair XA. If a borrow occurs as a result, the carry flag is set; if not, the carry flag is reset. 404 CHAPTER 11 INSTRUCTION SET SUBC rp’1, XA Function: rp’1, CY ← rp’1 – XA – CY Subtracts the contents of register pair XA from the contents of register pair rp’1 (HL, DE, BC, XA’, HL’, DE’, or BC’), including the carry flag, and sets the result to specified register pair rp’1. If a borrow occurs as a result, the carry flag is set; if not, the carry flag is reset. AND A, #n4 Function: A ← A ∧ n4 n4 = l3-0 : 0-FH ANDs 4-bit immediate data n4 with the contents of the A register, and sets the result to the A register. Application example To clear the high-order 2 bits of the accumulator to 0 AND A, #0011B AND A, @HL Function: A ← A ∧ (HL) ANDs the contents of the data memory addressed by register pair HL with the contents of the A register, and sets the result to the A register. AND XA, rp’ Function: XA ← XA ∧ rp’ ANDs the contents of register pair rp’ (XA, HL, DE, BC, XA’, HL’, DE’, or BC’) with the contents of register pair XA, and sets the result to register pair XA. 405 CHAPTER 11 INSTRUCTION SET AND rp’1, XA Function: rp’ 1 ← rp’1 ∧ XA ANDs the contents of register pair XA with register pair rp’1 (HL, DE, BC, XA’, HL’, DE’, or BC’), and sets the result to the specified register pair. OR A, #n4 Function: A ← A ∨ n4 n4 = l3-0 : 0-FH ORs 4-bit immediate data n4 with the contents of the A register, and sets the result to the A register. Application example To set the low-order 3 bits of the accumulator to 1 OR A, #0111B OR A, @HL Function: A ← A ∨ (HL) ORs the contents of the data memory addressed by register pair HL with the contents of the A register, and sets the result to the A register. OR XA, rp’ Function: XA ← XA ∨ rp’ ORs the contents of register pair rp’ (XA, HL, DE, BC, XA’, HL’, DE’, or BC’) with the contents of register pair XA, and sets the result to register pair XA. 406 CHAPTER 11 INSTRUCTION SET OR rp’1, XA Function: rp’ 1 ← rp’1 ∨ XA ORs the contents of register pair XA with register pair rp’1 (HL, DE, BC, XA’, HL’, DE’, or BC’), and sets the result to the specified register pair rp’1. XOR A, #n4 Function: A ← A ∨ n4 n4 = l3-0 : 0-FH Exclusive-ORs 4-bit immediate data n4 with the contents of the A register, and sets the result to the A register. Application example To invert the high-order 4 bits of the accumulator XOR A, #1000B XOR A, @HL Function: A ← A ∨ (HL) Exclusive-ORs the contents of the data memory addressed by register pair HL with the contents of the A register, and sets the result to the A register. XOR XA, rp’ Function: XA ← XA ∨ rp’ Exclusive-ORs the contents of register pair rp’ (XA, HL, DE, BC, XA’, HL’, DE’, or BC’) with the contents of register pair XA, and sets the result to register pair XA. 407 CHAPTER 11 INSTRUCTION SET XOR rp’1, XA Function: rp’ 1 ← rp’1 ∨ XA Exclusive-ORs the contents of register pair XA with register pair rp’1 (HL, DE, BC, XA’, HL’, DE’, or BC’), and sets the result to the specified register pair rp’1. 408 CHAPTER 11 INSTRUCTION SET 11.4.5 Accumulator manipulation instructions RORC A Function: CY ← A 0, An–1 ← A n, A3 ← CY (n = 1-3) Rotates the contents of the A register (4-bit accumulator) 1 bit to the right with the carry flag. A CY Before execution RORC A After execution 1 0 0 1 0 0 3 0 2 1 1 0 0 1 NOT A Function: A ← A Takes 1’s complement of the A register (4-bit accumulator) (inverts the bits of the accumulator). 409 CHAPTER 11 INSTRUCTION SET 11.4.6 Increment/decrement instructions INCS reg Function: reg ← reg + 1; Skip if reg = 0 Increments the contents of register reg (X, A, H, L, D, E, B, or C). If reg = 0 as a result, the next instruction is skipped. INCS rp1 Function: rp1 ← rp1 + 1; Skip if rp1 = 00H Increments the contents of register pair rp1 (HL, DE, or BC). If rp1 = 00H as a result, the next instruction is skipped. INCS @HL Function: (HL) ← (HL) + 1; Skip if (HL) = 0 Increments the contents of the data memory addressed by register pair HL. If the contents of the data memory become 0 as a result, the next instruction is skipped. INCS mem Function: (mem) ← (mem) + 1; Skip if (mem) = 0, mem = D7-0 : 00H-FFH Increments the contents of the data memory addressed by 8-bit immediate data mem. If the contents of the data memory become 0 as a result, the next instruction is skipped. 410 CHAPTER 11 INSTRUCTION SET DECS reg Function: reg ← reg – 1; Skip if reg = FH Decrements the contents of register reg (X, A, H, L, D, E, B, or C). If reg = FH as a result, the next instruction is skipped. DECS rp’ Function: rp’ ← rp’ – 1; Skip if rp’ = FFH Decrements the contents of register pair rp’ (XA, HL, DE, BC, XA’, HL’, DE’ or BC’). If rp’ = FFH as a result, the next instruction is skipped. 411 CHAPTER 11 INSTRUCTION SET 11.4.7 Compare instructions SKE reg, #n4 Function: Skip if reg = n4 n4 = I3-0 : 0-FH Skips the next instruction if the contents of register reg (X, A, H, L, D, E, B, or C) are equal to 4-bit immediate data n4. SKE @HL, #n4 Function: Skip if (HL) = n4 n4 = I 3-0: 0-FH Skips the next instruction if the contents of the data memory addressed by register pair HL are equal to 4-bit immediate data n4. SKE A, @HL Function: Skip if A = (HL) Skips the next instruction if the contents of the A register are equal to the contents of the data memory addressed by register pair HL. SKE XA, @HL Function: Skip if A = (HL) and X = (HL + 1) Skips the next instruction if the contents of the A register are equal to the contents of the data memory addressed by register pair HL and if the contents of the X register are equal to the contents of the next memory address. However, if the contents of the L register are an odd number, an address whose least significant bit is ignored is specified. 412 CHAPTER 11 INSTRUCTION SET SKE A, reg Function: Skip if A = reg Skips the next one instruction if the contents of the A register are equal to register reg (X, A, H, L, D, E, B, or C). SKE XA, rp’ Function: Skip if XA = rp’ Skips the next one instruction if the contents of register pair XA are equal to the contents of register pair rp’ (XA, HL, DE, BC, XA’, HL’, DE’, or BC’). 413 CHAPTER 11 INSTRUCTION SET 11.4.8 Carry flag manipulation instructions SET1 CY Function: CY ← 1 Sets the carry flag. CLR1 CY Function: CY ← 0 Clears the carry flag. SKT CY Function: Skip if CY = 1 Skips the next one instruction if the carry flag is 1. NOT1 CY Function: CY ← CY Inverts the carry flag. Therefore, sets the carry flag to 1 if it is 0, and clears the flag to 0 if it is 1. 414 CHAPTER 11 INSTRUCTION SET 11.4.9 Memory bit manipulation instructions SET1 mem. bit Function: (mem. bit) ← 1 mem = D7-0 : 00H-FFH, bit = B1-0 : 0-3 Sets the bit specified by 2-bit immediate data bit at the address specified by 8-bit immediate data mem. SET1 fmem. bit SET1 pmem. @L SET1 @H+mem. bit Function: (bit specified by operand) ← 1 Sets the bit of the data memory addressed in the bit manipulation addressing mode (fmem. bit, pmem. @L, or @H+mem. bit). CLR1 mem. bit Function: (mem. bit) ← 0 mem = D7-0 : 00H-FFH, bit = B1-0 : 0-3 Clears the bit specified by 2-bit immediate data bit at the address specified by 8-bit immediate data mem. CLR1 fmem. bit CLR1 pmem. @L CLR1 @H+mem. bit Function: (bit specified by operand) ← 0 Clears the bit of the data memory addressed in the bit manipulation addressing mode (fmem. bit, pmem. @L, or @H+mem. bit). 415 CHAPTER 11 INSTRUCTION SET SKT mem. bit Function: Skip if (mem. bit) = 1 mem = D7-0 : 00H-FFH, bit = B1-0 : 0-3 Skips the next instruction if the bit specified by 2-bit immediate data bit at the address specified by 8-bit immediate data mem is 1. SKT fmem. bit SKT pmem. @L SKT @H+mem. bit Function: Skip if (bit specified by operand) = 1 Skips the next instruction if the bit of the data memory addressed in the bit manipulation addressing mode (fmem. bit, pmem. @L, or @H+mem. bit) is 1. SKF mem. bit Function: Skip if (mem. bit) = 0 mem = D7-0 : 00H-FFH, bit = B1-0 : 0-3 Skips the next instruction if the bit specified by 2-bit immediate data bit at the address specified by 8-bit immediate data mem is 0. SKF fmem. bit SKF pmem. @L SKF @H+mem. bit Function: Skip if (bit specified by operand) = 0 Skips the next instruction if the bit of the data memory addressed in the bit manipulation addressing mode (fmem. bit, pmem. @L, or @H+mem. bit) is 0. 416 CHAPTER 11 INSTRUCTION SET SKTCLR fmem. bit SKTCLR pmem. @L SKTCLR @H+mem. bit Function: Skip if (bit specified by operand) = 1 then clear Skips the next instruction if the bit of the data memory addressed in the bit manipulation addressing mode (fmem. bit, pmem. @L, or @H+mem. bit) is 1, and then clears the bit to “0”. AND1 CY, fmem. bit AND1 CY, pmem. @L AND1 CY, @H+mem. bit Function: CY ← CY ∧ (bit specified by operand) ANDs the content of the carry flag with the contents of the data memory addressed in the bit manipulation addressing mode (fmem. bit, pmem. @L, or @H+mem. bit), and sets the result to the carry flag. OR1 CY, fmem. bit OR1 CY, pmem. @L OR1 CY, @H+mem. bit Function: CY ← CY ∨ (bit specified by operand) ORs the content of the carry flag with the contents of the data memory addressed in the bit manipulation addressing mode (fmem. bit, pmem. @L, or @H+mem. bit), and sets the result to the carry flag. 417 CHAPTER 11 INSTRUCTION SET XOR1 CY, fmem. bit XOR1 CY, pmem. @L XOR1 CY, @H+mem. bit Function: CY ← CY ∨ (bit specified by operand) Exclusive-ORs the content of the carry flag with the contents of the data memory addressed in the bit manipulation addressing mode (fmem. bit, pmem. @L, or @H+mem. bit), and sets the result to the carry flag. 418 CHAPTER 11 INSTRUCTION SET 11.4.10 Branch instructions BR addr Function: µ PD753108 PC12-0 ← addr addr = 0000H-1FFFH Branches to an address specified by immediate data addr. This instruction is an assembler pseudo-instruction and is replaced by the assembler at assembly time with the optimum instruction from the BR !addr, BRCB !caddr, and BR $addr instructions. II BR addr1 Function: µ PD753108 PC12-0 ← addr1 addr1 = 0000H-1FFFH Branches to an address specified by immediate data addr1. This instruction is an assembler pseudo-instruction and is replaced by the assembler at assembly time with the optimum instruction from the BRA !addr1, BR !addr, BRCB !caddr, and BR $addr1 instructions. II BRA !addr1 Function: µ PD753108 PC12-0 ← addr1 BR !addr Function: µ PD753108 PC12-0 ← addr addr = 0000H-1FFFH Transfers immediate data addr to the program counter (PC) and branches to the address specified by the PC. Remark The function described in this section applies to the µPD753108, which has a 13-bit program counter and addr = 0000H-1FFFH. Interpret the above explanation according to the case where the µPD753104, µ PD753106, and µ PD75P3116 have the program counters of 12 bits and addr = 000HFFFH, 13 bits and addr = 0000H-17FFH, and 14 bits and addr = 0000H-3FFFH, respectively. 419 CHAPTER 11 INSTRUCTION SET BR $addr Function: µ PD753108 PC12-0 ← addr addr = (PC – 15) to (PC – 1), (PC + 2) to (PC + 16) This is a relative branch instruction that has a branch range of (–15 to –1) and (+2 to +16) from the current address. It is not affected by a page boundary or block boundary. II BR $addr1 Function: µ PD753108 PC12-0 ← addr1 addr1 = (PC – 15) to (PC – 1), (PC + 2) to (PC + 16) This is a relative branch instruction that has a branch range of (–15 to –1) and (+2 to +16) from the current address. It is not affected by a page boundary or block boundary. Remark The function described in this section applies to the µPD753108, which has a 13-bit program counter and addr = 0000H-1FFFH. Interpret the above explanation according to the case where the µPD753104, µ PD753106, and µ PD75P3116 have the program counters of 12 bits and addr = 000HFFFH, 13 bits and addr = 0000H-17FFH, and 14 bits and addr = 0000H-3FFFH, respectively. 420 CHAPTER 11 INSTRUCTION SET BRCB !caddr Function: µ PD753108 PC 12-0 ← PC 12 + caddr11-0 caddr = n000H-nFFFH n = PC 12 = 0, 1 Branches to an address specified by the low-order 12 bits of the program counter (PC11-0) replaced with 12-bit immediate data caddr. Caution The BRCB !caddr instruction usually branches execution within the block where the instruction exists. If the first byte of this instruction is at address 0FFEH or 0FFFH, however, execution does not branch to block 0 but to block 1. Program memory 7 Block 0 0FFEH a 0FFFH b 1000H Block 1 0 If the BRCB !caddr instruction is at position a or b in the figure above, execution branches to block 1, not block 0. Remark The function described in this section applies to the µPD753108, which has a 13-bit program counter and addr = 0000H-1FFFH. Interpret the above explanation according to the case where the µPD753104, µ PD753106, and µ PD75P3116 have the program counters of 12 bits and addr = 000HFFFH, 13 bits and addr = 0000H-17FFH, and 14 bits and addr = 0000H-3FFFH, respectively. 421 CHAPTER 11 INSTRUCTION SET BR PCDE Function: µ PD753108 PC 12-0 ← PC12-8 + DE PC 7-4 ← D, PC 3-0 ← E Branches to the address specified by the low-order 8 bits of the program counter (PC7-0) replaced with the contents of register pair DE. The high-order bits of the program counter are not affected. Caution The BR PCDE instruction usually branches execution within the page where the instruction exists. If the first byte of the op code is at address ×× FE or ×× FFH, however, execution does not branch in that page, but to the next page. Program memory 7 Page 2 02FEH a 02FFH b 0300H Page 3 0 For example, if the BR PCDE instruction is at position a or b in the above figure, execution branches to the loworder 8-bit address specified by the contents of register pair DE in page 3, not in page 2. BR PCXA Function: µ PD753108 PC 12-0 ← PC12-8 + XA PC 7-4 ← X, PC3-0 ← A Branches to the address specified by the low-order 8 bits of the program counter (PC7-0) replaced with the contents of register pair XA. The high-order bits of the program counter are not affected. Caution This instruction branches execution to the next page, not to the same page, if the first byte of the op code is at address ××FEH or ×× FFH, in the same manner as the BR PCDE instruction. Remark The function described in this section applies to the µPD753108, which has a 13-bit program counter and addr = 0000H-1FFFH. Interpret the above explanation according to the case where the µPD753104, µ PD753106, and µ PD75P3116 have the program counters of 12 bits and addr = 000HFFFH, 13 bits and addr = 0000H-17FFH, and 14 bits and addr = 0000H-3FFFH, respectively. 422 CHAPTER 11 INSTRUCTION SET BR BCDE Function: µ PD753108 PC 12-0 ← B 0 + CDE Branches to the address specified by the contents of the program counter replaced with the contents of registers B0, C, D, and E. 12 PC 0 B 11 87 43 0 3 C 0 3 D 0 3 E 0 BR BCXA Function: µ PD753108 PC 12-0 ← B 0 + CXA Branches to the address specified by the contents of the program counter replaced with the contents of registers B0, C, X, and A. 12 PC 0 B 11 87 43 0 3 C 0 3 X 0 3 A 0 TBR addr Function: This is an assembler pseudo-instruction for table definition by the GETI instruction. It is used to replace a 3byte BR !addr instruction with a 1-byte GETI instruction. Code the 12-bit address data as addr. For details, refer to the RA75X Assembler Package User’s Manual – Language . Remark The function described in this section applies to the µPD753108, which has a 13-bit program counter and addr = 0000H-1FFFH. Interpret the above explanation according to the case where the µPD753104, µ PD753106, and µ PD75P3116 have the program counters of 12 bits and addr = 000HFFFH, 13 bits and addr = 0000H-17FFH, and 14 bits and addr = 0000H-3FFFH, respectively. 423 CHAPTER 11 INSTRUCTION SET 11.4.11 II Subroutine stack control instructions CALLA !addr1 Function: µ PD753108 (SP – 2) ← × , ×, MBE, RBE, (SP – 3) ← PC7-4 (SP – 4) ← PC3-0 , (SP – 5) ← 0, 0, 0, PC 12 (SP – 6) ← PC11-8 PC 12–0 ← addr1, SP ← SP – 6 I/II CALL !addr Function: µ PD753108 [Mk I mode] (SP – 1) ← PC7-4 , (SP – 2) ← PC3-0 (SP – 3) ← MBE, RBE, 0, PC 12 (SP – 4) ← PC11-8 , PC12-0 ← addr, SP ← SP – 4 addr = 0000H-1FFFH [Mk II mode] (SP – 2) ← × , ×, MBE, RBE (SP – 3) ← PC 7-4 , (SP – 4) ← PC3-0 (SP – 5) ← 0, 0, 0, PC 12, (SP – 6) ← PC11-8 PC 12-0 ← addr, SP ← SP – 6 addr = 0000H-1FFFH Saves the contents of the program counter (return address), MBE, and RBE to the data memory (stack) addressed by the stack pointer (SP), decrements the SP, and then branches to the address specified by 14-bit immediate data addr. Remark The function described in this section applies to the µPD753108, which has a 13-bit program counter and addr = 0000H-1FFFH. Interpret the above explanation according to the case where the µPD753104, µ PD753106, and µ PD75P3116 have the program counters of 12 bits and addr = 000HFFFH, 13 bits and addr = 0000H-17FFH, and 14 bits and addr = 0000H-3FFFH, respectively. 424 CHAPTER 11 INSTRUCTION SET I/II CALLF !faddr Function: µ PD753108 [Mk I mode] (SP – 1) ← PC7-4 , (SP – 2) ← PC3-0 (SP – 3) ← MBE, RBE, 0, PC 12 (SP – 4) ← PC11–8, SP ← SP – 4 PC 12–0 ← 00 + faddr faddr = 0000H-07FFH [Mk II mode] (SP – 2) ← × , ×, MBE, RBE (SP – 3) ← PC7-4 , (SP – 4) ← PC3-0 (SP – 5) ← 0, 0, 0, PC 12, (SP – 6) ← PC11–8 SP ← SP – 6 PC12–0 ← 00 + faddr faddr = 0000H-07FFH Saves the contents of the program counter (return address), MBE, and RBE to the data memory (stack) addressed by the stack pointer (SP), decrements the SP, and then branches to the address specified by 11-bit immediate data faddr. The address range from which a subroutine can be called is limited to 0000H to 07FFH (0 to 2047). TCALL !addr Function This is an assembler pseudo-instruction for table definition by the GETI instruction. It is used to replace a 3byte CALL !addr instruction with a 1-byte GETI instruction. Code 12-bit address data as addr. For details, refer to the RA75X Assembler Package User’s Manual – Language . Remark The function described in this section applies to the µPD753108, which has a 13-bit program counter and addr = 0000H-1FFFH. Interpret the above explanation according to the case where the µPD753104, µ PD753106, and µ PD75P3116 have the program counters of 12 bits and addr = 000HFFFH, 13 bits and addr = 0000H-17FFH, and 14 bits and addr = 0000H-3FFFH, respectively. 425 CHAPTER 11 INSTRUCTION SET I/II RET Function: µ PD753108 [Mk I mode] PC 11-8 ← (SP), MBE, RBE, 0, PC12 ← (SP + 1) PC 3-0 ← (SP + 2), PC 7-4 ← (SP + 3), SP ← SP + 4 [Mk II mode] PC11-8 ← (SP), MBE, 0, 0, PC 12 ← (SP + 1) PC 3-0 ← (SP + 2), PC 7-4 ← (SP + 3) ×, ×, MBE, RBE ← (SP + 4) SP ← SP + 6 Restores the contents of the data memory (stack) addressed by the stack pointer (SP) to the program counter (PC), memory bank enable flag (MBE), and register bank enable flag (RBE), and then increments the contents of the SP. Caution I/II None of the flags of the program status word (PSW), except MBE and RBE, are restored. RETS Function: µ PD753108 [Mk I mode] PC 11-8 ← (SP), MBE, 0, 0, PC 12 ← (SP + 1) PC 3-0 ← (SP + 2), PC 7-4 ← (SP + 3), SP ← SP + 4 Then skip unconditionally [Mk II mode] PC11-8 ← (SP), 0, 0, 0, PC12 ← (SP + 1) PC 3-0 ← (SP + 2), PC 7-4 ← (SP + 3) ×, ×, MBE, RBE ← (SP + 4), SP ← SP + 6 Then skip unconditionally Restores the contents of the data memory (stack) addressed by the stack pointer (SP) to the program counter (PC), memory bank enable flag (MBE), and register bank enable flag (RBE), increments the contents of the SP, and then skips unconditionally. Caution None of the flags of the program status word (PSW), except MBE and RBE, are restored. Remark The function described in this section applies to the µPD753108, which has a 13-bit program counter and addr = 0000H-1FFFH. Interpret the above explanation according to the case where the µPD753104, µ PD753106, and µ PD75P3116 have the program counters of 12 bits and addr = 000HFFFH, 13 bits and addr = 0000H-17FFH, and 14 bits and addr = 0000H-3FFFH, respectively. 426 CHAPTER 11 INSTRUCTION SET I/II RETI Function: µ PD753108 [Mk I mode] PC 11-8 ← (SP), MBE, RBE, 0, PC 12 ← (SP + 1) PC 3-0 ← (SP + 2), PC 7-4 ← (SP + 3) PSWL ← (SP + 4), PSWH ← (SP + 5) SP ← SP + 6 [Mk II mode] PC 11-8 ← (SP), 0, 0, 0, PC 12 ← (SP + 1) PC 3-0 ← (SP + 2), PC 7-4 ← (SP + 3) PSWL ← (SP + 4), PSWH ← (SP + 5) SP ← SP + 6 Restores the contents of the data memory (stack) addressed by the stack pointer (SP) to the program counter (PC) and program status word (PSW), and then increments the contents of the SP. This instruction is used to return execution from an interrupt processing routine. Remark The function described in this section applies to the µPD753108, which has a 13-bit program counter and addr = 0000H-1FFFH. Interpret the above explanation according to the case where the µPD753104, µ PD753106, and µ PD75P3116 have the program counters of 12 bits and addr = 000HFFFH, 13 bits and addr = 0000H-17FFH, and 14 bits and addr = 0000H-3FFFH, respectively. 427 CHAPTER 11 INSTRUCTION SET PUSH rp Function: (SP – 1) ← rpH, (SP – 2) ← rpL, SP ← SP – 2 Saves the contents of register pair rp (XA, HL, DE, or BC) to the data memory (stack) addressed by the stack pointer (SP), and then decrements the contents of the SP. The high-order 4 bits of the register pair (rpH: X, H, D, or B) are saved to the stack addressed by (SP – 1), and the low-order 4 bits (rpL : A, L, E, or C) are saved to the stack addressed by (SP – 2). PUSH BS Function: (SP – 1) ← MBS, (SP – 2) ← RBS, SP ← SP – 2 Saves the contents of the memory bank selection register (MBS) and register bank selection register (RBS) to the data memory (stack) addressed by the stack pointer (SP), and then decrements the contents of the SP. POP rp Function: rp L ← (SP), rpH ← (SP + 1), SP ← SP + 2 Restores the contents of the data memory addressed by the stack pointer (SP) to register pair rp (XA, HL, DE, or BC), and then increments the contents of the stack pointer. The contents of (SP) are restored to the low-order 4 bits of the register pair (rpL: A, L, E, or C), and the contents of (SP + 1) are restored to the high-order 4 bits (rpH: X, H, D, or B). POP BS Function: RBS ← (SP), MBS ← (SP + 1), SP ← SP + 2 Restores the contents of the data memory (stack) addressed by the stack pointer (SP) to the register bank selection register (RBS) and memory bank selection register (MBS), and then increments the contents of the SP. 428 CHAPTER 11 INSTRUCTION SET 11.4.12 Interrupt control instructions EI Function: IME (IPS. 3) ← 1 Sets the interrupt mask enable flag (bit 3 of the interrupt priority selection register) to “1” to enable interrupts. Acknowledging an interrupt is controlled by an interrupt enable flag corresponding to the interrupt. EI IE××× Function: IE ××× ← 1 ××× = N 5, N2-0 Sets a specified interrupt enable flag (IE××× ) to “1” to enable acknowledging the corresponding interrupt ( ××× = BT, CSI, T0, T, T2, W, 0, 1, 2, or 4). DI Function: IME (IPS. 3) ← 0 Resets the interrupt mask enable flag (bit 3 of the interrupt priority selection register) to “0” to disable all interrupts, regardless of the contents of the respective interrupt enable flags. DI IE××× Function: IE ××× ← 0 ××× = N 5, N2-0 Resets a specified interrupt enable flag (IE××× ) to “0” to disable acknowledging the corresponding interrupt ( ××× = BT, CSI, T0, T1, T2, W, 0, 1, 2, or 4). 429 CHAPTER 11 INSTRUCTION SET 11.4.13 Input/output instructions IN A, PORTn Function: A ← PORTn n = N3-0: 0-3, 5, 6, 8, or 9 Transfers the contents of a port specified by PORTn (n = 0-3, 5, 6, 8, or 9) to the A register. Caution When this instruction is executed, it is necessary to set MBE = 0 or (MBE = 1, MBS = 15). Only 0 to 3, 5, 6, 8 or 9 can be specified to n. The data of the output latch is loaded to the A register in the output mode, and the data of the port pins are loaded to the register in the input mode by specifying input/output mode. IN XA, PORTn Function: A ← PORTn, X ← PORTn+1 n = N 3-0: 8 Transfers the contents of the port specified by PORTn (n = 8) to the A register, and transfers the contents of the next port to the X register. Caution Only 8 can be specified as n. When this instruction is executed, it is necessary to set MBE = 0 or (MBE = 1, MBS = 15). The data of the output latch is loaded to the A and X registers in the output mode, and the data of the port pins are loaded to the registers in the input mode by specifying input/output mode. 430 CHAPTER 11 INSTRUCTION SET OUT PORTn, A Function: PORTn ← A n = N3-0: 2, 3, 5, 6, 8, or 9 Transfers the contents of the A register to the output latch of a port specified by PORTn (n = 2, 3, 5, 6, 8, or 9). Caution When this instruction is executed, it is necessary to set MBE = 0 or (MBE = 1, MBS = 15). Only 2, 3, 5, 6, 8, or 9 can be specified as n. OUT PORTn, XA Function: PORTn ← A, PORTn+1 ← X n = N3-0: 8 Transfers the contents of the A register to the output latch of a port specified by PORTn (n = 8), and the contents of the X register to the output latch of the next port. Caution When this instruction is executed, it is necessary to set MBE = 0 or (MBE = 1, MBS = 15). Only 8 can be specified as n. 431 CHAPTER 11 INSTRUCTION SET 11.4.14 CPU control instructions HALT Function: PCC. 2 ← 1 Sets the HALT mode (this instruction sets bit 2 of the processor clock control register). Caution Make sure that a NOP instruction follows the HALT instruction. STOP Function: PCC. 3 ← 1 Sets the STOP mode (this instruction sets bit 3 of the processor clock control register). Caution Make sure that a NOP instruction follows the STOP instruction. NOP Function: Does nothing but consumes 1 machine cycle. 432 CHAPTER 11 INSTRUCTION SET 11.4.15 Special instructions SEL RBn Function: RBS ← n n = N1-0: 0-3 Sets 2-bit immediate data n to the register bank selection register (RBS). SEL MBn Function: MBS ← n n = N3-0: 0, 1, 15 Transfers 4-bit immediate data n to the memory bank selection register (MBS). I/II GETI taddr Function: µ PD753108 taddr = T 5-0, 0: 20H-7FH [Mk I mode] • When a table defined by the TBR instruction is referenced PC 12-0 ← (taddr)4-0 + (taddr + 1) • When a table defined by the TCALL instruction is referenced (SP – 1) ← PC7-4, (SP – 2) ← PC3-0 (SP – 3) ← MBE, RBE, 0, PC12 (SP – 4) ← PC11-8 PC 12-0 ← (taddr)4-0 + (taddr + 1) SP ← SP – 4 • When a table defined by an instruction other than TBR or TCALL is referenced Executes instruction with (taddr) (taddr + 1) as op code Remark The function described in this section applies to the µPD753108, which has a 13-bit program counter and addr = 0000H-1FFFH. Interpret the above explanation according to the case where the µPD753104, µ PD753106, and µ PD75P3116 have the program counters of 12 bits and addr = 000HFFFH, 13 bits and addr = 0000H-17FFH, and 14 bits and addr = 0000H-3FFFH, respectively. 433 CHAPTER 11 INSTRUCTION SET [Mk II mode] • When a table defined by the TBR instruction is referencedNote PC 12-0 ← (taddr)4-0 + (taddr + 1) • When a table defined by the TCALL instruction is referencedNote (SP – 2) ← ×, ×, MBE, RBE (SP – 3) ← PC7-4, (SP – 4) ← PC3-0 (SP – 5) ← 0, 0, 0, PC 12, (SP – 6) ← PC11-8 PC 12-0 ← (taddr)4-0 + (taddr + 1) SP ← SP – 6 • When a table defined by an instruction other than TBR or TCALL is referenced Executes instruction with (taddr) (taddr + 1) as op code Note The address specified by the TBR and TCALL instructions is limited to 0000H to 3FFFH. References the 2-byte data at the program memory address specified by (taddr), (taddr + 1) and executes it as an instruction. The area of the reference table consists of addresses 0020H through 007FH. Data must be written to this area in advance. When the data to be written is 1-byte or 2-byte instructions, code the mnemonics directly. When a 3-byte call instruction or 3-byte branch instruction is used, data is written by using an assembler pseudoinstruction (TCALL or TBR). Only an even address can be specified by taddr. Remark The function described in this section applies to the µPD753108, which has a 13-bit program counter and addr = 0000H-1FFFH. Interpret the above explanation according to the case where the µPD753104, µ PD753106, and µ PD75P3116 have the program counters of 12 bits and addr = 000HFFFH, 13 bits and addr = 0000H-17FFH, and 14 bits and addr = 0000H-3FFFH, respectively. 434 CHAPTER 11 INSTRUCTION SET Caution Only the 2-machine cycle instructions can be placed in the reference table as a 2-byte instructions (except the BRCB and CALLF instructions). Two 1-byte instructions can be used only in the following combinations: Instruction of 1st Byte MOV MOV XCH A, @HL @HL, A A, @HL Instruction of 2nd Byte INCS DECS INCS DECS INCS INCS DECS INCS DECS INCS MOV XCH A, @DL A, @DL INCS DECS INCS DECS L L H H HL E E D D DE L L D D MOV XCH A, @DE A, @DE The contents of the PC are not incremented while the GETI instruction is executed. Therefore, after the referenced instruction has been executed, processing continues from the address following that of the GETI instruction. If the instruction preceding the GETI instruction has a skip function, the GETI instruction is skipped in the same manner as other 1-byte instructions. If the instruction referenced by the GETI instruction has a skip function, the instruction that follows the GETI instruction is skipped. If an instruction having a string effect is referenced by the GETI instruction, it is executed as follows: • If the instruction preceding the GETI instruction has the string effect in the same group as the referenced instruction, the string effect is lost and the referenced instruction is not skipped when GETI instruction is executed. • If the instruction next to GETI instruction has the string effect in the same group as the referenced instruction, the string effect by the referenced instruction is valid, and the instruction following that instruction is skipped. 435 CHAPTER 11 INSTRUCTION SET Application example MOV MOV CALL BR HL00 : XAFF : CSUB1 : BSUB2 : HL, #00H XA, #FFH SUB1 SUB2 ORG MOV MOV TCALL TBR . . . . . . GETI . . . . . . GETI . . . . . . GETI . . . . . . GETI 20H HL, #00H XA, #FFH SUB1 SUB2 Replaced by GETI HL00 ; MOV HL, #00H BSUB2 ; BR SUB2 CSUB1 ; CALL SUB1 XAFF ; MOV XA, #FFH 436 APPENDIX A µPD75308B, 753108 AND 75P3116 FUNCTIONAL LIST Parameter Program memory µPD75308B Mask ROM 0000H-1F7FH (8064 × 8 bits) 000H-1FFH (512 × 4 bits) 75X Standard µPD753108 Mask ROM 0000H-1FFFH (8192 × 8 bits) µPD75P3116 One-time PROM 0000H-3FFFH (16384 × 8 bits) Data memory CPU Instruction When main system execution clock is selected time When subsystem clock is selected Stack SBS register Stack area Subroutine call instruction stack operation Instruction BRA !addr1 CALLA !addr1 MOVT XA, @BCDE MOVT XA, @BCXA BR BCDE BR BCXA CALL !addr CALLF !faddr I/O port CMOS input CMOS input/output Bit port output N-ch open-drain input/output Total 75XL CPU 0.95, 1.91, 15.3 µs • 0.95, 1.91, 3.81, 15.3 µs (during 4.19-MHz operation) (during 4.19-MHz operation) • 0.67, 1.33, 2.67, 10.7 µs (during 6.0-MHz operation) 122 µs (32.768-kHz operation) None 000H-0FFH 2-byte stack SBS.3 = 1: Mk I mode selection SBS.3 = 0: Mk II mode selection 000H-1FFH When MK I mode: 2-byte stack When MK II mode: 3-byte stack When MK I mode: unavailable When MK II mode: available Available Unavailable 3 machine cycles 2 machine cycles 8 16 8 8 40 Mk I mode: 3 machine cycles, Mk II mode: 4 machine cycles Mk I mode: 2 machine cycles, Mk II mode: 3 machine cycles 8 20 0 4 32 437 APPENDIX A µPD75308B, 753108 AND 75P3116 FUNCTIONAL LIST Parameter LCD controller/driver µ PD75308B µ PD753108 µ PD75P3116 Segment selection: 24/28/32 Segment selection: 16/20/24 segments (can be changed to CMOS (can be changed to CMOS input/output port in 4 timeinput/output port in 4 time- unit; max. 8) unit; max. 8) Display mode selection: static, 1/2 duty (1/2 bias), 1/3 duty (1/2 bias), 1/3 duty (1/3 bias), 1/4 duty (1/3 bias) On-chip split resistor for LCD driver can be specified by using mask option. No on-chip split resistor for LCD driver 5 channels • Basic interval timer/watchdog timer: 1 channel • 8-bit timer/event counter: 3 channels (can be used as a 16-bit timer/event counter, carrier generator, gated timer) • Watch timer: 1 channel • Φ, 524, 262, 65.5 kHz (Main system clock: during 4.19-MHz operation) • Φ, 750, 375, 93.8 kHz (Main system clock: during 6.0-MHz operation) • 2, 4, 32 kHz (Main system clock: during 4.19-MHz operation or subsystem clock: during 32.768-kHz operation) • 2.93, 5.86, 46.9 kHz (Main system clock: during 6.0-MHz operation) Timer 3 channels • Basic interval timer: 1 channel • 8-bit timer/event counter: 1 channel • Watch timer: 1 channel • Φ , 524, 262, 65.5 kHz (Main system clock: during 4.19-MHz operation) 2 kHz (Main system clock: during 4.19-MHz operation) Clock output (PCL) BUZ output (BUZ) Serial interface 3 modes are available • 3-wire serial I/O mode ... MSB/LSB can be selected for transfer first bit • 2-wire serial I/O mode • SBI mode None None None No None Contained Contained Yes Yes Yes SOS Feedback resistor cut flag register (SOS.0) Subsystem clock oscillator current cut flag (SOS.1) Register bank selection register (RBS) Standby release by INT0 Interrupt priority selection register (IPS) 438 APPENDIX A µPD75308B, 753108 AND 75P3116 FUNCTIONAL LIST Parameter Vectored interrupt Supply voltage Operating ambient temperature Package µ PD75308B External: 3, internal: 3 VDD = 2.0 to 6.0 V TA = –40 to +85°C µ PD753108 External: 3, internal: 5 VDD = 1.8 to 5.5 V µ PD75P3116 • 80-pin plastic QFP • 64-pin plastic QFP (14 × 14 mm) (14 × 20 mm) • 64-pin plastic QFP (12 × 12 mm) • 80-pin plastic QFP (14 × 14 mm) • 80-pin plastic TQFP (Fine pitch) (12 × 12 mm) 439 [MEMO] 440 APPENDIX B DEVELOPMENT TOOLS The following development tools are provided for system development using the µPD753108. In 75XL Series, the relocatable assembler which is common to the series is used in combination with the device file of each product. Language processor RA75X relocatable assembler Host Machine OS PC-9800 series MS-DOS Ver. 3.30 to Ver. 6.2Note Distribution Media 3.5-inch 2HD 5-inch 2HD 3.5-inch 2HC 5-inch 2HC Part Number (Product Name) µS5A13RA75X µS5A10RA75X µS7B13RA75X µS7B10RA75X IBM PC/AT™ and Refer to compatible machines “OS for IBM PC” Device file Host Machine OS PC-9800 series MS-DOS Ver. 3.30 to Ver. 6.2Note Distribution Media 3.5-inch 2HD 5-inch 2HD 3.5-inch 2HC 5-inch 2HC Part Number (Product Name) µS5A13DF753108 µS5A10DF753108 µS7B13DF753108 µS7B10DF753108 IBM PC/AT and Refer to compatible machines “OS for IBM PC” Note Although MS-DOS ver.5.00 and later versions have the task swap function, the function cannot be used with this software. Remark Operations of the assembler and device file are guaranteed only on the above host machines and OSs. 441 APPENDIX B DEVELOPMENT TOOLS PROM write tools Hardware PG-1500 PG-1500 is a PROM programmer which enables you to program single-chip microcontrollers including PROM by stand-alone or host machine operation by connecting an attached board and optional programmer adapter to PG-1500. It also enables you to program typical PROM devices of 256K bits to 4M bits. PROM programmer adapter for the µPD75P3116GC. Connect the programmer adapter to PG-1500 for use. PROM programmer adapter for the µ PD75P3116GK. Connect the programmer adapter to PG-1500 for use. PG-1500 and a host machine are connected by serial and parallel interface and PG-1500 is controlled on the host machine. Host Machine OS PC-9800 series MS-DOS Ver. 3.30 to Ver. 6.2Note Distribution Media 3.5-inch 2HD 5-inch 2HD 3.5-inch 2HC 5-inch 2HC Part Number (Product Name) PA-75P3116GC PA-75P3116GK Software PG-1500 controller µ S5A13PG1500 µ S5A10PG1500 µ S7B13PG1500 µ S7B10PG1500 IBM PC/AT and Refer to compatible machines “OS for IBM PC ” Note Although MS-DOS ver.5.00 and later versions have the task swap function, the function cannot be used with this software. Remark Operation of the PG-1500 controller is guaranteed only on the above host machines and OSs. 442 APPENDIX B DEVELOPMENT TOOLS Debugging tool The in-circuit emulators (IE-75000-R and IE-75001-R) are available as the program debugging tool for the µ PD753108. The system configurations are described as follows. Hardware IE-75000-R Note 1 In-circuit emulator for debugging the hardware and software when developing the application systems that use the 75X Series and 75XL Series. When developing a µ PD753108 Subseries, the emulation board IE-75300-R-EM and emulation probe that are sold separately must be used with the IE-75000-R. By connecting with the host machine and the PROM programmer, efficient debugging can be made. It contains the emulation board IE-75000-R-EM which is connected. In-circuit emulator for debugging the hardware and software when developing the application systems that use the 75X Series and 75XL Series. When developing a µ PD753108 Subseries, the emulation board IE-75300-R-EM and emulation probe that are sold separately must be used with the IE-75001-R. By connecting with the host machine and the PROM programmer, efficient debugging can be made. Emulation board for evaluating the application systems that use a µPD753108 Subseries. It must be used with the IE-75000-R or IE-75001-R. EP-753108GC-R Emulation probe for the µ PD753108GC. It must be connected to the IE-75000-R (or IE-75001-R) and IE-75300-R-EM. It is supplied with the 64-pin conversion socket EV-9200GC-64 which facilitates connection to a target system. IE-75001-R IE-75300-R-EM EV-9200GC-64 EP-753108GK-R Emulation probe for the µ PD753108GK. It must be connected to the IE-75000-R (or IE-75001-R) and IE-75300-R-EM. It is supplied with the 64-pin conversion adapter TGK-064SBW which facilitates connection TGK-064SBWNote 2 to a target system. Connects the IE-75000-R or IE-75001-R to a host machine via RS-232-C and Centronics interface and controls the above hardware on a host machine. Host Machine OS PC-9800 series MS-DOS Ver. 3.30 to Ver. 6.2 Note 3 Distribution Media 3.5-inch 2HD 5-inch 2HD 3.5-inch 2HC 5-inch 2HC Part Number (Product Name) Software IE control program µ S5A13IE75X µ S5A10IE75X µ S7B13IE75X µ S7B10IE75X IBM PC/AT and Refer to compatible machines “OS for IBM PC ” Notes 1. Maintenance parts 2. Made by TOKYO ELETECH CORPORATION (TEL: 03-5295-1661). Consult an NEC sales representative for purchasing. 3. Although MS-DOS ver.5.00 and later versions have the task swap function, the function cannot be used with this software. Remarks 1. Operation of the IE control program is guaranteed only on the above host machines and OSs. 2. The µ PD753104, 753106, 753108, and 75P3116 are collectively called µ PD753108 Subseries. 443 APPENDIX B DEVELOPMENT TOOLS OS for IBM PC The following IBM PC OSs are supported. OS PC DOS MS-DOS IBM DOSTM Version Ver. 3.1 to Ver. 6.3 J6.1/V Note to J6.3/VNote Ver. 5.00 to Ver. 6.22 5.0/VNote to 6.2/VNote J5.02/VNote Note Only English version is supported. Caution Ver. 5.0 and later versions have the task swap function, but it cannot be used with this software. 444 Development Tool Configuration In-circuit emulator IE-75000-R or IE-75001-R Centronics I/F Emulation board RS-232-C IE control program Host machine PC-9800 series IBM PC/AT Symbolic debug enable IE-75300-R-EMNote 1 EP-753108GC-R EP-753108GK-R Emulation probe APPENDIX B Note 2 PG-1500 controller On-chip PROM version PROM programmer Target system DEVELOPMENT TOOLS µ PD75P3116GC/GK PG-1500 Relocatable assembler + + Programmer adapter Notes 1. In-circuit emulator does not contain IE-75300-R-EM (option). PA-75P3116GC PA-75P3116GK 2. EV-9200GC-64 TGK-064SBW Device file 445 APPENDIX B DEVELOPMENT TOOLS Package Drawing and Recommended Footprint of Conversion Socket (EV-9200GC-64) Figure B-1. Package Drawing of EV-9200GC-64 (for reference only) A E B F M R N O D C S T K Q EV-9200GC-64 1 No.1 pin index P G H I EV-9200GC-64-G0 ITEM A B C D E F G H I J K L M N O P Q R S T MILLIMETERS 18.8 14.1 14.1 18.8 4-C 3.0 0.8 6.0 15.8 18.5 6.0 15.8 18.5 8.0 7.8 2.5 2.0 1.35 0.35 ± 0.1 φ 2.3 φ 1.5 J INCHES 0.74 0.555 0.555 0.74 4-C 0.118 0.031 0.236 0.622 0.728 0.236 0.622 0.728 0.315 0.307 0.098 0.079 0.053 0.014+0.004 –0.005 φ 0.091 φ 0.059 446 L APPENDIX B DEVELOPMENT TOOLS Figure B-2. Recommended Footprint of EV-9200GC-64 (for reference only) G J K D E F L C B A EV-9200GC-64-P1E ITEM A B C D E F G H I J K L Caution MILLIMETERS 19.5 14.8 0.8±0.02 × 15=12.0±0.05 INCHES 0.768 0.583 0.031+0.002 × –0.001 0.591=0.472 +0.003 –0.002 0.8±0.02 × 15=12.0±0.05 0.031+0.002 × 0.591=0.472 +0.003 –0.001 –0.002 14.8 19.5 6.00 ± 0.08 6.00 ± 0.08 0.5 ± 0.02 0.583 0.768 0.236 +0.004 –0.003 0.236 +0.004 –0.003 0.197 +0.001 –0.002 φ 2.36 ± 0.03 φ 2.2 ± 0.1 φ 1.57 ± 0.03 φ 0.093 +0.001 –0.002 φ 0.087 +0.004 –0.005 φ 0.062 +0.001 –0.002 Dimensions of mount pad for EV-9200 and that for target device (QFP) may be different in some parts. For the recommended mount pad dimensions for QFP, refer to "SEMICONDUCTOR DEVICE MOUNTING TECHNOLOGY MANUAL" (C10535E). I H 447 [MEMO] 448 APPENDIX C ORDERING MASK ROMS After your program has been developed, place an order for a mask ROM using the following procedure: Reservation for ordering mask ROM Inform NEC of your schedule to place an order for the mask ROM (NEC’s response may be delayed if it is not informed in advance). Preparation of ordering media The following three media for ordering the mask ROM are available: • UV-EPROM Note • 3.5-inch IBM-format floppy disk (outside Japan only) • 5-inch IBM-format floppy disk (outside Japan only) Note Prepare three UV-EPROMs having the same contents when ordering with UV-EPROM. For the product with mask option, write down the mask option data on the mask option information sheet. Preparation of necessary documents Fill out the following documents when ordering the mask ROM: A. B. Mask ROM Ordering Sheet Mask ROM Ordering Check Sheet C. Mask Option Information Sheet (necessary for product with mask option) Ordering Submit the media prepared in and documents prepared in to NEC by the reserved date. Caution Refer to the information document, ROM Code Ordering Method (C10302J: Japaneseversion) for details. 449 [MEMO] 450 APPENDIX D INSTRUCTION INDEX D.1 Instruction Index (by function) [Operation instructions] ADDS ADDS ADDS ADDS ADDS ADDC ADDC ADDC SUBS SUBS SUBS SUBC SUBC SUBC AND AND AND AND OR OR OR OR XOR XOR XOR XOR A, #n4 ··· 368, 401 XA, #n8 ··· 368, 401 A, @HL ··· 368, 401 XA, rp’ ··· 368, 401 rp’1, XA ··· 368, 402 A, @HL ··· 368, 402 XA, rp’ ··· 368, 402 rp’1, XA ··· 368, 403 A, @HL ··· 369, 403 XA, rp’ ··· 369, 403 rp’1, XA ··· 369, 404 A, @HL ··· 369, 404 XA, rp’ ··· 369, 404 rp’1, XA ··· 369, 405 A, #n4 ··· 369, 405 A, @HL ··· 369, 405 XA, rp’ ··· 369, 405 rp’1, XA ··· 369, 406 A, #n4 ··· 369, 406 A, @HL ··· 369, 406 XA, rp’ ··· 369, 406 rp’1, XA ··· 369, 407 A, #n4 ··· 369, 407 A, @HL ··· 369, 407 XA, rp’ ··· 369, 407 rp’1, XA ··· 369, 408 [Transfer instructions] MOV MOV MOV MOV MOV MOV MOV MOV MOV MOV MOV MOV MOV MOV MOV MOV MOV MOV MOV MOV XCH XCH XCH XCH XCH XCH XCH XCH XCH A, #n4 ··· 367, 390 reg1, #n4 ··· 367, 390 XA, #n8 ··· 367, 390 HL, #n8 ··· 367, 390 rp2, #n8 ··· 367, 390 A, @HL ··· 367, 391 A, @HL+ ··· 367, 391 A, @HL– ··· 367, 391 A, @rpa1 ··· 367, 391 XA, @HL ··· 367, 391 @HL, A ··· 367, 391 @HL, XA ··· 367, 392 A, mem ··· 367, 392 XA, mem ··· 367, 392 mem, A ··· 367, 392 mem, XA ··· 367, 392 A, reg ··· 367, 393 XA, rp’ ··· 367, 393 reg1, A ··· 367, 393 rp’1, XA ··· 367, 393 A, @HL ··· 367, 394 A, @HL+ ··· 367, 394 A, @HL– ··· 367, 394 A, @rpa1 ··· 367, 394 XA, @HL ··· 367, 394 A, mem ··· 367, 394 XA, mem ··· 367, 395 A, reg1 ··· 367, 395 XA, rp’ ··· 367, 395 [Accumulator manipulation instructions] RORC NOT A ··· 369, 409 A ··· 369, 409 [Table reference instructions] MOVT MOVT MOVT MOVT XA, @PCDE ··· 368, 396 XA, @PCXA ··· 368, 398 XA, @BCDE ··· 368, 399 XA, @BCXA ··· 368, 399 [Increment/decrement instructions] INCS INCS INCS INCS [Bit transfer instructions] MOV1 MOV1 MOV1 MOV1 MOV1 MOV1 CY, fmem. bit ··· 368, 400 CY, pmem. @L ··· 368, 400 CY, @H+mem. bit ··· 368, 400 fmem. bit, CY ··· 368, 400 pmem. @L, CY ··· 368, 400 @H+mem. bit, CY ··· 368, 400 DECS DECS reg ··· 369, 410 rp1 ··· 369, 410 @HL ··· 369, 410 mem ··· 369, 410 reg ··· 369, 411 rp’ ··· 369, 411 451 APPENDIX D INSTRUCTION INDEX [Compare instructions] SKE SKE SKE SKE SKE SKE reg, #n4 ··· 369, 412 @HL, #n4 ··· 369, 412 A, @HL ··· 369, 412 XA, @HL ··· 369, 412 A, reg ··· 369, 413 XA, rp’ ··· 369, 413 [Branch instructions] BR BR BRA BR BR BR BRCB BR BR BR BR TBR addr ··· 371, 419 addr1 ··· 372, 419 !addr1 ··· 374, 419 !addr ··· 372, 419 $addr ··· 372, 420 $addr1 ··· 373, 420 !caddr ··· 374, 421 PCDE ··· 373, 422 PCXA ··· 373, 422 BCDE ··· 373, 423 BCXA ··· 373, 423 addr ··· 381, 423 [Carry flag manipulation instructions] SET1 CLR1 SKT NOT1 CY ··· 370, 414 CY ··· 370, 414 CY ··· 370, 414 CY ··· 370, 414 [Memory bit manipulation instructions] SET1 SET1 SET1 SET1 CLR1 CLR1 CLR1 CLR1 SKT SKT SKT SKT SKF SKF SKF SKF mem. bit ··· 370, 415 fmem. bit ··· 370, 415 pmem. @L ··· 370, 415 @H+mem. bit ··· 370, 415 mem. bit ··· 370, 415 fmem. bit ··· 370, 415 pmem. @L ··· 370, 415 @H+mem. bit ··· 370, 415 mem. bit ··· 370, 416 fmem. bit ··· 370, 416 pmem. @L ··· 370, 416 @H+mem. bit ··· 370, 416 mem. bit ··· 370, 416 fmem. bit ··· 370, 416 pmem. @L ··· 370, 416 @H+mem. bit ··· 370, 416 [Subroutine stack control instructions] CALLA CALL CALLF TCALL !addr1 ··· 374, 424 !addr ··· 375, 424 !faddr ··· 376, 425 !addr ··· 381, 425 RET ··· 377, 426 RETS ··· 378, 426 RETI ··· 379, 427 PUSH PUSH POP POP rp ··· 379, 428 BS ··· 379, 428 rp ··· 379, 428 BS ··· 379, 428 [Interrupt control instructions] EI ··· 379, 429 EI DI IE ××× ··· 379, 429 IE ××× ··· 379, 429 DI ··· 379, 429 SKTCLR fmem. bit ··· 370, 417 SKTCLR pmem. @L ··· 370, 417 SKTCLR @H+mem. bit ··· 370, 417 AND1 AND1 AND1 OR1 OR1 OR1 XOR1 XOR1 XOR1 CY, fmem. bit ··· 370, 417 CY, pmem. @L ··· 370, 417 CY, @H+mem. bit ··· 370, 417 CY, fmem. bit ··· 370, 417 CY, pmem. @L ··· 370, 417 CY, @H+mem. bit ··· 370, 417 CY, fmem. bit ··· 370, 418 CY, pmem. @L ··· 370, 418 CY, @H+mem. bit ··· 370, 418 [Input/output instructions] IN IN OUT OUT A, PORTn ··· 380, 430 XA, PORTn ··· 380, 430 PORTn, A ··· 380, 431 PORTn, XA ··· 380, 431 [CPU control instructions] HALT ··· 380, 432 STOP ··· 380, 432 NOP ··· 380, 432 [Special instructions] SEL SEL GETI RBn ··· 380, 433 MBn ··· 380, 433 taddr ··· 381, 433 452 APPENDIX D INSTRUCTION INDEX D.2 [A] Instruction Index (alphabetical order) [E] A, @HL ··· 368, 402 rp’1, XA ··· 368, 403 XA, rp’ ··· 368, 402 A, #n4 ··· 368, 401 A, @HL ··· 368, 401 rp’1, XA ··· 368, 402 XA, rp’ ··· 368, 401 XA, #n8 ··· 368, 401 A, #n4 ··· 369, 405 A, @HL ··· 369, 405 rp’1, XA ··· 369, 406 XA, rp’ ··· 369, 405 CY, fmem. bit ··· 370, 417 CY, pmem. @L ··· 370, 417 CY, @H+mem. bit ··· 370, 417 [I] IN IN INCS INCS INCS INCS A, PORTn ··· 380, 430 XA, PORTn ··· 380, 430 mem ··· 369, 410 reg ··· 369, 410 rp1 ··· 369, 410 @HL ··· 369, 410 [H] HALT ··· 380, 432 [G] GETI taddr ··· 381, 433 EI ··· 379, 429 EI IE ××× ··· 379, 429 ADDC ADDC ADDC ADDS ADDS ADDS ADDS ADDS AND AND AND AND AND1 AND1 AND1 [B] BR BR BR BR BR BR BR BR BR BRA BRCB [C] CALL CALLA CALLF CLR1 CLR1 CLR1 CLR1 CLR1 [D] DECS DECS DI addr ··· 371, 419 addr1 ··· 372, 419 BCDE ··· 373, 423 BCXA ··· 373, 423 PCDE ··· 373, 422 PCXA ··· 373, 422 !addr ··· 372, 419 $addr ··· 372, 420 $addr1 ··· 373, 420 !addr1 ··· 374, 419 !caddr ··· 374, 421 [M] MOV MOV MOV MOV MOV MOV MOV MOV MOV MOV MOV MOV A, mem ··· 367, 392 A, reg ··· 367, 393 A, #n4 ··· 367, 390 A, @HL ··· 367, 391 A, @HL+ ··· 367, 391 A, @HL– ··· 367, 391 A, @rpa1 ··· 367, 391 HL, #n8 ··· 367, 390 mem, A ··· 367, 392 mem, XA ··· 367, 392 reg1, A ··· 367, 393 reg1, #n4 ··· 367, 390 rp’1, XA ··· 367, 393 rp2, #n8 ··· 367, 390 XA, mem ··· 367, 392 XA, rp’ ··· 367, 393 XA, #n8 ··· 367, 390 XA, @HL ··· 367, 391 @HL, A ··· 367, 391 @HL, XA ··· 367, 392 XA, @BCDE ··· 368, 399 XA, @BCXA ··· 368, 399 XA, @PCDE ··· 368, 396 XA, @PCXA ··· 368, 398 CY, fmem. bit ··· 368, 400 CY, pmem. @L ··· 368, 400 !addr ··· 375, 424 !addr1 ··· 374, 424 !faddr ··· 376, 425 CY ··· 370, 414 fmem. bit ··· 370, 415 mem. bit ··· 370, 415 pmem. @L ··· 370, 415 @H+mem. bit ··· 370, 415 MOV MOV MOV MOV MOV MOV MOV MOV MOVT MOVT reg ··· 369, 411 rp’ ··· 369, 411 IE××× ··· 379, 429 MOVT MOVT MOV1 MOV1 DI ··· 379, 429 453 APPENDIX D INSTRUCTION INDEX MOV1 MOV1 MOV1 MOV1 [N] CY, @H+mem. bit ··· 368, 400 fmem. bit, CY ··· 368, 400 pmem. @L, CY ··· 368, 400 @H+mem. bit, CY ··· 368, 400 SKF SKF SKF SKT SKT SKT SKT SKT mem. bit ··· 370, 416 pmem. @L ··· 370, 416 @H+mem. bit ··· 370, 416 CY ··· 370, 414 fmem. bit ··· 370, 416 mem. bit ··· 370, 416 pmem. @L ··· 370, 416 @H+mem. bit ···· 370, 416 NOP ··· 380, 432 NOT NOT1 [O] OR OR OR OR OR1 OR1 CR1 OUT OUT [P] POP POP PUSH PUSH [R] RET ··· 377, 426 RETI ··· 379, 427 RETS ··· 378, 426 RORC [S] SEL SEL SET1 SET1 SET1 SET1 SET1 SKE SKE SKE SKE SKE SKE SKF MBn ··· 380, 433 RBn ··· 380, 433 CY ··· 370, 414 fmem. bit ··· 370, 415 mem. bit ··· 370, 415 pmem. @L ··· 370, 415 @H+mem. bit ··· 370, 415 A, reg ··· 369, 413 A, @HL ··· 369, 412 reg, #n4 ··· 369, 412 XA, rp’ ··· 369, 413 XA, @HL ··· 369, 412 @HL, #n4 ··· 369, 412 fmem. bit ··· 370, 416 A ··· 369, 409 BS ··· 379, 428 rp ··· 379, 428 BS ··· 379, 428 rp ··· 379, 428 A, #n4 ··· 369, 406 A, @HL ··· 369, 406 rp’1, XA ··· 369, 407 XA, rp’ ··· 369, 406 CY, fmem. bit ··· 370, 417 CY, pmem. @L ··· 370, 417 CY, @H+mem. bit ··· 370, 417 PORTn, A ··· 380, 431 PORTn, XA ··· 380, 431 A ··· 369, 409 CY ··· 370, 414 SKTCLR fmem. bit ··· 370, 417 SKTCLR pmem. @L ··· 370, 417 SKTCLR @H+mem. bit ··· 370, 417 STOP ··· 380, 432 SUBC SUBC SUBC SUBS SUBS SUBS [T] TBR TCALL [X] XCH XCH XCH XCH XCH XCH XCH XCH XCH XOR XOR XOR XOR XOR1 XOR1 XOR1 A, mem ··· 367, 394 A, reg1 ··· 367, 395 A, @HL ··· 367, 394 A, @HL+ ··· 367, 394 A, @HL– ··· 367, 394 A, @rpa1 ··· 367, 394 XA, mem ··· 367, 395 XA, rp’ ··· 367, 395 XA, @HL ··· 367, 394 A, #n4 ··· 369, 407 A, @HL ··· 369, 407 rp’1, XA ··· 369, 408 XA, rp’ ··· 369, 407 CY, fmem. bit ··· 370, 418 CY, pmem. @L ··· 370, 418 CY, @H+mem. bit ··· 370, 418 addr ··· 381, 423 !addr ··· 381, 425 A, @HL ··· 369, 404 rp’1, XA ··· 369, 405 XA, rp’ ··· 369, 404 A, @HL ··· 369, 403 rp’1, XA ··· 369, 404 XA, rp’ ··· 369, 403 454 APPENDIX E HARDWARE INDEX [A] ACKD ··· 212 ACKE ··· 212 ACKT ··· 212 [B] BS ··· 93 BSB0 to BSB3 ··· 298 BSYE ··· 212 BT ··· 130 BTM ··· 130 [C] CLOM ··· 127 CMDD ··· 213 CMDT ··· 213 COI ··· 210 CSIE ··· 209 CSIM ··· 208 CY ··· 89 [I] IE0 ··· 305 IE1 ··· 305 IE2 ··· 328 IE4 ··· 305 IEBT ··· 305 IECSI ··· 305 IET0 ··· 305 IET1 ··· 305 IET2 ··· 305 IEW ··· 328 IM0 ··· 311 IM1 ··· 311 IM2 ··· 331 IME ··· 307 INTA ··· 68 INTC ··· 68 INTE ··· 68 INTF ··· 68 INTG ··· 68 INTH ··· 68 IPS ··· 306 IRQ0 ··· 305 IRQ1 ··· 305 IRQ2 ··· 328 IRQ4 ··· 305 IRQBT ··· 305 IRQCSI ··· 305 IRQT0 ··· 305 IRQT1 ··· 305 IRQT2 ··· 305 IRQW ··· 328 IST0, IST1 ··· 91, 312 [K] KR0 to KR3 ··· 329 [L] LCDC ··· 273 LCDM ··· 271 [M] MBE ··· 43, 92 MBS ··· 43, 93 [N] NRZ ··· 150 NRZB ··· 150 [P] PC ··· 73 PCC ··· 114 PMGA, PMGB, PMGC ··· 101 POGA, POGB ··· 108 PORT0 to 3, 5, 6, 8, 9 ··· 96 PSW ··· 89 [R] RBE ··· 59, 92 RBS ··· 59, 93 RELD ··· 213 RELT ··· 213 REMC ··· 150 [S] SBIC ··· 211 SBS ··· 72, 85 SCC ··· 116 SIO ··· 214 455 APPENDIX E HARDWARE INDEX SK0 to SK2 ··· 90 SOS ··· 122 SP ··· 85 SVA ··· 215 [T] T0, T1, T2 ··· 67 TC2 ··· 150 TGCE ··· 150 TM0, TM1, TM2 ··· 145 TMOD0, TMOD1, TMOD2 ··· 67 TMOD2H ··· 66, 144 TOE0 ··· 149 TOE1 ··· 149 TOE2 ··· 150 [W] WDTM ··· 132 WM ··· 139 WUP ··· 210 456 APPENDIX F REVISION HISTORY The table shown below lists the major revised points in each edition of this manual. Note that, in the "Including Chapter" column, the chapter numbers and names of each edition are shown, not necessarily this edition. Edition Second Description The development status of the µPD753104, 753106, 753108, and 75P3116 is changed from “Under development” to “Development completed.” The input withstand voltage of the port 5’s pins in the N-ch open-drain mode is changed from 12 V to 13 V. A caution description is added for the S16/P93 to S19/P90 and S20/P83 to S23/P80 pins used as segment signal outputs. An explanation for the feedback resistor mask options is added in paragraph “Subsystem clock oscillator control register (SOS).” Values for 6.00-MHz operation are added in the “Resolution and Maximum Allowable Time Setting” tables. Of the LCD drive modes, the lower LCD drive voltage limit in the normal mode is changed from 2.7 V to 2.2 V. The explanation about mask options is added. Entries in the instruction function description sections are rearranged according to those in the “Instruction Sets and their Operations” section. The versions of the supported operating systems are upgraded. Third Data bus pins (D0 to D7) are added. “List of Recommended Connections for Unused Pins” is changed. Caution in “Differences between Mk I Mode and Mk II Mode” is changed. Description on feedback resistor mask option in the section of the “Subsystem clock oscillator control register (SOS)” is deleted. “Maximum Time Required to Switch System to/from CPU Clocks” is changed. “Switching between System Clock and CPU Clock” is changed. Cautions are added to “Bus release signal (REL)” and “Command signal (CMD).” “Mask Option Selection” is added. “Writing Program Memory” is changed. “Reading Program Memory” is changed. “Mask Option of Feedback Resistor for Subsystem Clock” is deleted. Ordering media in “Ordering Mask ROMs” are changed. CHAPTER 7 STANDBY FUNCTION CHAPTER 9 WRITING AND VERIFYING PROM (PROGRAM MEMORY) CHAPTER 10 MASK OPTION APPENDIX C ORDERING MASK ROMS CHAPTER 10 MASK OPTION CHAPTER 11 INSTRUCTION SET APPENDIX B DEVELOPMENT TOOLS Throughout CHAPTER 2 PIN FUNCTION CHAPTER 4 INTERNAL CPU FUNCTIONS CHAPTER 5 PERIPHERAL HARDWARE FUNCTION CHAPTER 5 PERIPHERAL HARDWARE FUNCTION Including Chapter Throughout 457 [MEMO] 458 Facsimile Message From: Name Company Although NEC has taken all possible steps to ensure that the documentation supplied to our customers is complete, bug free and up-to-date, we readily accept that errors may occur. Despite all the care and precautions we've taken, you may encounter problems in the documentation. Please complete this form whenever you'd like to report errors or suggest improvements to us. Tel. FAX Address Thank you for your kind support. North America Hong Kong, Philippines, Oceania NEC Electronics Inc. NEC Electronics Hong Kong Ltd. Corporate Communications Dept. Fax: +852-2886-9022/9044 Fax: 1-800-729-9288 1-408-588-6130 Korea Europe NEC Electronics Hong Kong Ltd. NEC Electronics (Europe) GmbH Seoul Branch Technical Documentation Dept. Fax: 02-528-4411 Fax: +49-211-6503-274 South America NEC do Brasil S.A. Fax: +55-11-6465-6829 Taiwan NEC Electronics Taiwan Ltd. Fax: 02-719-5951 Asian Nations except Philippines NEC Electronics Singapore Pte. Ltd. Fax: +65-250-3583 Japan NEC Semiconductor Technical Hotline Fax: 044-548-7900 I would like to report the following error/make the following suggestion: Document title: Document number: Page number: If possible, please fax the referenced page or drawing. Document Rating Clarity Technical Accuracy Organization CS 98.2 Excellent Good Acceptable Poor