UPG153TB

PRELIMINARY DATA SHEET L, S Band SPDT GaAs MMIC Switch FEATURES • LOW INSERTION LOSS: LINS = 0.5 dB TYP (UPG153TB), 0.6 dB TYP (UPG155TB) at VCONT = +3.0 V/0 V, f = 1 GHz • HIGH LINEARITY SWITCHING: Pin (0.1 dB) = +29.0 dBm TYP (UPG153TB) Pin (0.1 dB) = +30.5 dBm TYP (UPG155TB) at VCONT = +3.0 V/0 V, f = 2 GHz • SMALL 6 PIN MINI-MOLD PACKAGE: Size: 2.0 x 1.25 x 0.9 mm UPG153TB UPG155TB DESCRIPTION The UPG153TB and UPG155TB are L-band SPDT (Single Pole Double Throw) GaAs FET switches for digital cellular or cordless telephone application. The devices can operate from 100 MHz to 2.5 GHz with low insertion loss. These devices are housed in an original 6 pin super mini-mold package similar to SOT363. NEC's stringent quality assurance and test procedures assure the highest reliability and performance. APPLICATION • L, S-BAND DIGITAL CELLULAR OR CORDLESS TELEPHONE • PCS, WLAN AND WLL APPLICATIONS ELECTRICAL CHARACTERISTICS (Unless otherwise specified, TA = 25°C, VCONT1 = 3 V, VCONT2 = 0 V or VCONT1 = 0 V, VCONT2 = 3 V; off chip DC blocking capacitor value, 51 pF) PART NUMBER PACKAGE OUTLINE SYMBOLS LINS PARAMETERS AND CONDITIONS Insertion Loss at f = 0.1 to 1 GHz f = 2 GHz f = 2.5 GHz Isolation at f = 0.1 to 2 GHz f = 2.5 GHz f = 1 GHz Input Return Loss at f = 0.1 to 2 GHz Input Return Loss at f = 0.1 to 2 GHz Input Power at 0.1 dB Compression Point, f = 2 GHz Input Power at 1 dB Compression Point, f = 2 GHz Switching Speed Control Current at VCONT = 3 V/0 V, no RF signal UNITS dB dB dB dB dB dB dB dB dBm dBm ns µA 31 10 15 11 11 MIN UPG153TB S06 TYP 0.5 0.7 0.9 13 10 18.5 15 15 29 33 30 20 50 32 MAX 0.65 0.9 13 18 11 11 MIN UPG155TB S06 TYP 0.6 0.75 0.9 16 10 21.5 15 15 30.5 34 30 20 50 MAX 0.8 1.0 ISOL RLIN RLOUT PIN(0.1 dB) PIN(1 dB) tsw ICONT Note: 1. It is necessary to use DC blocking capacitors for the RF input and RF output. The value of DC blocking capacitors should be chosen to accommodate the frequency of operation. The range of recommended DC blocking capacitor value is less than 100 pF. 2. The distance between IC's GND pin and ground pattern of substrate should be as short as possible to avoid parasitics. California Eastern Laboratories UPG153TB, UPG155TB ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C) SYMBOLS VCONT1, 2 PIN PTOT TA TSTG PARAMETERS Control Voltage 1, 2 2 Input Power UPG155TB UPG153TB Total Power Dissipation3 Operating Temperature Storage Temperature UNITS V dBm W °C °C RATINGS -6 to +6 +34 +33 0.15 -45 to +85 -55 to +150 Notes: 1. Operation in excess of any one of these conditions may result in permanent damage. 2. 2.5 V ≤ I VCONT1 - VCONT2 I ≤ 6 V 3. Mounted on a 50 x 50 x 1.6 mm double copper clad epoxy glass PWB, TA = +85 °C. RECOMMENDED OPERATING CONDITIONS (TA = 25°C) SYMBOLS VCONT VCONT PARAMETERS Control Voltage (High) Control Voltage (Low) UNITS V V MIN +2.5 -0.2 UPG153TB TYP MAX +3 0 +5.3 +0.2 MIN +2.7 -0.2 UPG155TB TYP +3 0 MAX +5.3 +0.2 TEST CIRCUIT1 OUT1 OUT2 C0 C0 1 2 3 G1J 6 C1 C0 5 4 C1 VCONT1 IN VCONT2 Note: 1. (TA = 25°C, VCONT1 = +3 V, VCONT2 = 0 V, VCONT1 = 0 V, VCONT2 = +3 V, f = 2 GHz; off chip DC blocking capacitors value: C0 = 51 pF, C1 = 1000 pF (Bypass)) UPG153TB, UPG155TB TRUTH TABLE OF SWITCHING BY CONDITION OF CONTROL VOLTAGE VCONT1 VCONT(H) Note 1 VCONT(L) OUT1 OUT2 OUT1 OUT2 Note 1 VCONT(H) VCONT2 IN IN VCONT(L) IN OUT1 OUT2 IN OUT1 OUT2 Note: 1. In case of VCONT1 = VCONT2 = High or VCONT1 = VCONT2 = Low (that is same control voltage for both pins), input signal (Pin 5) is output to OUT1 (Pin 1) and OUT2 (Pin 3). PIN CONNECTION DIAGRAM PIN NO. 1 2 3 4 5 6 CONNECTION OUT1 GND OUT2 VCONT2 IN VCONT1 UPG153TB (Top View) (Bottom View) (Top View) UPG155TB (Bottom View) 3 4 4 3 3 4 4 3 G1L G1J 2 5 5 2 2 5 5 2 1 6 6 1 1 6 6 1 UPG153TB, UPG155TB OUTLINE DIMENSIONS (Units in mm) PACKAGE OUTLINE S06 2.1 ± 0.1 1.25 ± 0.1 ORDERING INFORMATION PART NUMBER UPG153TB-E3 UPG155TB-E3 Note: Embossed Tape, 8 mm wide, Pins 1, 2, 3 face tape perforation side. QUANTITY 3 kpcs/Reel 3 kpcs/Reel 0.65 2.0 ± 0.2 1.3 0.2 (All Leads) 0.9 ± 0.1 0.7 0.15 - 0.05 0 ~ 0.1 +0.10 Note: All dimensions are typical unless otherwise specified. Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. EXCLUSIVE NORTH AMERICAN AGENT FOR NEC RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS CALIFORNIA EASTERN LABORATORIES • Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054-1817 • (408) 988-3500 • Telex 34-6393 • FAX (408) 988-0279 Internet: http://WWW.CEL.COM DATA SUBJECT TO CHANGE WITHOUT NOTICE 12/5/2001