PJ-A3670-165.0

PJ-A3670 Series VCXO Series (PECL) PJ-A3670 Series Rev J Frequency Range: 70.0 MHz to 200.0 MHz Description The PJ-A3670 Series of voltage controlled quartz crystal oscillators provide frequency control by applying a voltage to Pin 1. This unit supplies ECLiPS compatible outputs which are enabled when Pin 2 is set to a logic low or left open. Features Size, mm 9 x 14 I/O 6 J Lead Supply Voltage 3.3V • High Reliability - NEL HALT/HASS qualified for crystal oscillator start-up conditions • Low jitter - Wavecrest jitter characterization available • Frequency range—70.0 MHz to 200.0 MHz • Will withstand vapor phase temperatures of 253°C for 4 minutes maximum • Space-saving alternative to discrete component oscillators • Wide Absolute Pull Range • High shock resistance, to 3000g • 3.3 Volt operation • Metal lid electrically connected to ground to reduce EMI • High Q crystal actively tuned oscillator circuit • Power supply decoupling internal • No internal PLL avoids cascading PLL problems • High frequencies due to proprietary design • Gold plated leads—Solder dipped leads available upon request • RoHS Compliant, Lead Free Construction (unless solder dipped leads are supplied) Creating a Part Number PJ - A367X - FREQ Package Code PJ 6 J Lead 9x14 SMD Input Voltage Code Specification A 3.3 V APR/Performance 0 ±100 ppm 0-70°C 9 Customer Specific C ±100 ppm -40 to +85°C Drawing Specifications Electrical Connection Pin 1 2 3 4 5 6 Dimensions shown in inches and millimeters. 357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone: 262-763-3591 Fax: 262-763-2881 Email: nelsales@nelfc.com www.nelfc.com For the most up to date specifications on each NEL product, log on to our website— www.nelfc.com Connection VCO Output Enable VEE Output Output Complement VCC VCXO Series (PECL) PJ-A3670 Series Rev J Frequency Range: 70.0 MHz to 200.0 MHz Operating Conditions and Output Characteristics Electrical Characteristics Parameter Symbol — — VOL VOH tr, tf — APR — — — Frequency Duty Cycle Logic 0 Logic 1 Rise & Fall Time Jitter, RMS(1) Absolute Pull Range VCO Input Impedance VCO Linearity Transfer Function (2) — @VO /2 — — 20-80% VO — VCO=0.3 to 3.0 V 50 na dc current max VCO=0.3 to 3.0 V VCO=0.3 to 3.0 V Conditions 70.0 MHz 45/55% VCC -1.810 VDC VCC -1.200 VDC — — ±100 ppm 100K ohm — — Min Typical — — — — — 3 psec — — — Positive 200.0 MHz 55/45% VCC -1.620 VDC VCC -0.880 VDC 600 ps — — — 10% — Max Supply Voltage Supply Current Output Current Operating Temperature Storage Temperature Power Dissipation Lead Temperature Load General Characteristics Parameter Symbol VCC-VEE Nominal 3.135 V — — ICC IO — 0.0 mA — 0ºC TA TS — -55ºC PD — — Soldering, 10 sec. — TL 50 ohm to VCC -2 V or Thevenin Equivalent, Bias Required — Conditions Min Typical 3.3 V — — — — — — — 3.465 V 60 mA ±50.0 mA 70ºC 125ºC 208 mW 300ºC — Max Environmental and Mechanical Characteristics Mechanical Shock Thermal Shock Vibration Soldering Condition Hermetic Seal Per MIL-STD-202, Method 213, Condition E Per MIL-STD-833, Method 1011, Condition A 0.060" double amplitude 10 Hz to 55 Hz, 35g’s 55 Hz to 2000 Hz 300ºC for 10 seconds Leak rate less than 1 x 10 -8 atm.cc/sec of helium Footnotes: 1) Jitter performance is frequency dependent. Please contact factory for full Wavecrest characterization. RMS jitter bandwidth of 12kHz to 20MHz. 2) Frequency increase with increase in control voltage and is monotonic.