SU-A2D10

SU-A2D10 Series LVDS SU-A2D10 Series Rev A Frequency Range: 80.0MHz to 350.0MHz Description The SU-A29D10 Series of quartz crystal oscillators provides a LVDS compatible signal. Size, mm 9 x 14 Features • Wide frequency range–80.0MHz to 350.0MHz • User specified tolerance available • Will withstand SMD reflow temperatures of 183°C for 4 minutes maximum • High shock resistance, to 1000g • 3.3 volt operation (other voltages available upon request) • Cover connected to ground • Enable/Disable • LVDS output on pin 4, complement on Pin 5 I/O 6 pad Supply Voltage 3.3V / 2.5V • Low Jitter - Wavecrest jitter characterization available • High Reliability - NEL HALT/HASS qualified for crystal oscillator start-up conditions • Overtone technology • High Q Crystal actively tuned oscillator circuit • Power supply decoupling internal • No internal PLL avoids cascading PLL problems • High frequencies due to proprietary design Creating a Part Number SU - A2D1X - FREQ Package Code SU 6 pad 9x14mm SMD Input Voltage Code Specification A 3.3V B 2.5V Tolerance/Performance 0 ±100ppm 0-70°C 1 ±50ppm 0-70°C 7 ±25ppm 0-70°C 9 Customer Specific A ±20ppm 0-70°C B ±50ppm -40 to +85°C C ±100ppm -40 to +85°C Drawing Specifications For the most up to date specifications on each NEL product, log on to our website—www.nelfc.com Dimensions shown in inches and (mm). 357 Beloit Street, P.O. Box 457, Burlington, WI 53105-0457 U.S.A. Phone: 262-763-3591 Fax: 262-763-2881 Email: nelsales@nelfc.com www.nelfc.com Electrical Connections Pin Connection 1 Enable/Disable 2 N.C 3 Ground 4 Q Output 5 /Q Output 6 VCC LVDS SU-A2D10 Series Rev A Frequency Range: 80.0MHz to 350.0MHz Operating Conditions and Output Characteristics Electrical Characteristics Parameter Symbol Frequency Duty Cycle(2) Logic 0 (2) Logic 1 (2) Differential Voltage (2) Disable Voltage Enable Voltage(5) Rise & Fall Time (2) Tpd (4) Jitter, RMS(3) Frequency Stability (1) — VOL VOH VOD — — tr,tf — — dF/F — @ VO /2 — — — VEE=0V VEE=0V 20-80%VO — — Overall conditions including: voltage, calibration, temp., 10 yr aging, shock, vibration Conditions 80.0MHz 45/55% 0.80V 1.25V 250 mV — 2.0V — -0.5 ns — -100ppm Min Typical — — — — — — — — — — — 350.0MHz 55/45% 1.10V 1.55V 450 mV 0.8V — 700 ps +0.5 ns 3 psec +100ppm Max General Characteristics Parameter Symbol Supply Voltage VCC 3.3V±5% Supply Current ICC — Output Current IO Continuous Output Current Operating Temperature TA — Storage Temperature TS — Power Dissipation PD — Lead Temperature TL Soldering, 10 sec. Load 100 ohms across differential outputs Start-up Time tS — Conditions 3.135V 0.0 mA 0.0 mA 0°C -55°C — — — Min Typical 3.3V — — — — — — 2 ms 3.465V 80 mA ±50.0 mA 70°C 125°C 277 mW 300°C 10 ms Max Environmental and Mechanical Characteristics Mechanical Shock Thermal Shock Vibration Soldering Condition Hermetic Seal Per MIL-STD-202, Method 213, Condition E Per MIL-STD-833, Method 1011, Condition A 0.060” double amplitude 10 Hz to 55 Hz, 35g’s 55Hz to 2000 Hz 300°C for 10 seconds Leak rate less than 1 x 10 -8 atm.cc/sec of helium Footnotes: 1) Standard frequency stability (±20,±25,±50ppm & others available) 2) With Load of 100 ohms across differential outputs. 3) Jitter performance is frequency dependent. Please contact factory for full Wavecrest characterization. RMS jitter bandwidth of 12kHz to 20MHz. 4) Tpd is phase shift between the falling edge of pin 4 and the rising edge of pin 5. 5) Open to enable pin also enables the output.