NHD-0116DZ-FL-YBW-33V

NHD-0116DZ-FL-YBW-33V Character Liquid Crystal Display Module NHD0116DZFLYBW33V- Newhaven Display 1 line x 16 characters Model Transflective Yellow/Green LED Backlight STN- Yellow/Green 6:00 view Wide Temperature (-20°C~+70°C) 3.3 Vdd RoHS Compliant Newhaven Display International, Inc. 2511 Technology Drive, Suite 101 Elgin IL, 60124 Ph: 847-844-8795 Fax: 847-844-8796 www.newhavendisplay.com nhtech@newhavendisplay.com nhsales@newhavendisplay.com [1] Document Revision History Revision 0 Date 10/31/2011 Description 33V – improved liquid; VDD = 3.3V Functions and Features • • • • • 1 line x 16 characters Built-in controller (ST7066U) +3.3V Power Supply 1/16 duty, 1/5 bias RoHS compliant [2] Changed by SB PIN ASSIGNMENT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 A K VSS VDD V0 RS R/W E DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 LED+ LED- LED B/L TYPE Specification: 1) Driving: Duty:1/16, Bias: 1/5, VLCD: 3.2V, VDD: 3.3V 2) Viewing Direction: 6 O'clock 3) Display mode: STN/Yellow-Green/Positive/Transflective 4) Operating temp.: -20°C - 70°C; Storage temp: -30°C - 80°C 5) Driver: ST7066U or equivalent 6) Backlight: Yellow-Green [3] Display Pattern Newhaven Display Model Name: NHD-0116DZ-FL-YBW-33V Pin Description and Wiring Diagram Pin No. Symbol 1 2 3 4 5 6 7-10 VSS VDD V0 RS R/W E DB0 – DB3 External Connection Power Supply Power Supply Adj Power Supply MPU MPU MPU MPU 11-14 15 16 DB4 – DB7 LED+ LED- MPU Power Supply Power Supply Function Description Ground 3Supply Voltage for logic (+3.3V) Power supply for contrast (approx. 0.1V) Register select signal. RS=0: Command, RS=1: Data Read/Write select signal, R/W=1: Read R/W: =0: Write Operation enable signal. Falling edge triggered. Four low order bi-directional three-state data bus lines. These four are not used during 4-bit operation. Four high order bi-directional three-state data bus lines. Power supply for LED Backlight (+5.0V) Ground for Backlight Recommended LCD connector: 2.54mm pitch pins Backlight connector: --Mates with: --- [4] Electrical Characteristics Item Operating Temperature Range Storage Temperature Range Supply Voltage Supply Current Supply for LCD (contrast) “H” Level input “L” Level input “H” Level output “L” Level output Symbol Top Tst VDD IDD VDD-V0 Vih Vil Voh Vol Vled Iled Backlight Supply Voltage Backlight Supply Current Condition Absolute Max Absolute Max Ta=25°C, VDD=3.3V Ta=25°C Min. -20 -30 0.7 VDD 0 0.75 VDD - Typ. 3.3 1.0 3.2 - Max. +70 +80 1.5 VDD 0.6 0.2 VDD Unit ⁰C ⁰C V mA V V V V V Vled=5.0V - 5.0 110 125 V mA Optical Characteristics Item Viewing Angle – Vertical (top) Viewing Angle – Vertical (bottom) Viewing Angle – Horizontal (left) Viewing Angle – Horizontal (right) Contrast Ratio Response Time (rise) Response Time (fall) Symbol AV AV AH AH Cr Tr Tf Condition Cr ≥ 2 Cr ≥ 2 Cr ≥ 2 Cr ≥ 2 Min. - - Typ. 25 70 30 30 2 120 120 Max. 150 150 Unit ⁰ ⁰ ⁰ ⁰ ms ms Controller Information Built-in ST7066U. Download specification at http://www.newhavendisplay.com/app_notes/ST7066U.pdf Display Character Address Code: Location Address (HEX) 1 00 2 01 3 02 4 03 5 04 6 05 7 06 [5] 8 07 9 08 10 09 11 0A 12 0B 13 0C 14 0D 15 0E 16 0F Command Table Instruction code Instruction RS R/W DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Clear Display 0 0 0 0 0 0 0 0 0 1 Return Home 0 0 0 0 0 0 0 0 1 - Entry mode Set 0 0 0 0 0 0 0 1 I/D SH Display ON/ OFF control 0 0 0 0 0 0 1 D C B Cursor or Display shift 0 0 0 0 0 1 S/C R/L - - Function set 0 0 0 0 1 DL N F - - 0 0 0 1 0 0 1 Set CGRAM Address Set DDRAM Address Read busy Flag and Address 0 1 BF Write data To Address 1 0 D7 Read data From RAM 1 1 D7 Write “20H” to DDRA and set DDRAM address to “00H” from AC Set DDRAM address to “00H” From AC and return cursor to Its original position if shifted. The contents of DDRAM are not changed. Assign cursor moving direction And blinking of entire display Set display (D), cursor (C), and Blinking of cursor (B) on/off Control bit. Set cursor moving and display Shift control bit, and the Direction, without changing of DDRAM data. Set interface data length (DL: 8Bit/4-bit), numbers of display Line (N: =2-line/1-line) and, Display font type (F: 5x11/5x8) Execution time (fosc= 270 KHZ 1.53ms 1.53ms 39us 39us 39us AC3 AC2 AC1 AC0 Set CGRAM address in address counter. 39us AC4 AC3 AC2 AC1 AC0 Set DDRAM address in address counter. 39us AC5 AC4 AC6 AC5 Description Whether during internal Operation or not can be known AC6 AC5 AC4 AC3 AC2 AC1 AC0 By reading BF. The contents of Address counter can also be read. Write data into internal D6 D5 D4 D3 D2 D1 D0 RAM (DDRAM/CGRAM). Read data from internal D6 D5 D4 D3 D2 D1 D0 RAM (DDRAM/CGRAM). [6] 0us 43us 43us Built-in Font Table [7] Example Initialization Program 8-bit Initialization: /**********************************************************/ void command(char i) { P1 = i; //put data on output Port D_I =0; //D/I=LOW : send instruction R_W =0; //R/W=LOW : Write E = 1; Delay(1); //enable pulse width >= 300ns E = 0; //Clock enable: falling edge } /**********************************************************/ void write(char i) { P1 = i; //put data on output Port D_I =1; //D/I=LOW : send data R_W =0; //R/W=LOW : Write E = 1; Delay(1); //enable pulse width >= 300ns E = 0; //Clock enable: falling edge } /**********************************************************/ void init() { E = 0; Delay(100); //Wait >15 msec after power is applied command(0x30); //command 0x30 = Wake up Delay(30); //must wait 5ms, busy flag not available command(0x30); //command 0x30 = Wake up #2 Delay(10); //must wait 160us, busy flag not available command(0x30); //command 0x30 = Wake up #3 Delay(10); //must wait 160us, busy flag not available command(0x38); //Function set: 8-bit/2-line command(0x10); //Set cursor command(0x0c); //Display ON; Cursor ON command(0x06); //Entry mode set } /**********************************************************/ [8] 4-bit Initialization: /**********************************************************/ void command(char i) { P1 = i; //put data on output Port D_I =0; //D/I=LOW : send instruction R_W =0; //R/W=LOW : Write Nybble(); //Send lower 4 bits i = i 50⁰C,30min = 1 cycle 10 cycles 10-55Hz , 15mm amplitude. 60 sec in each of 3 directions X,Y,Z For 15 minutes VS=800V, RS=1.5kΩ, CS=100pF One time Note 1: No condensation to be observed. Note 2: Conducted after 4 hours of storage at 25⁰C, 0%RH. Note 3: Test performed on product itself, not inside a container. Precautions for using LCDs/LCMs See Precautions at www.newhavendisplay.com/specs/precautions.pdf Warranty Information and Terms & Conditions http://www.newhavendisplay.com/index.php?main_page=terms [10] Note +80⁰C , 48hrs 3