NHD-1.69-160128UGC3

NHD-1.69-160128UGC3 Graphic Color OLED Display Module NHD1.69160128UGC3- Newhaven Display 1.69” Diagonal Size 160 x 128 Pixels Model Full Color +3V Power Supply Newhaven Display International, Inc. 2661 Galvin Ct. Elgin IL, 60124 Ph: 847-844-8795 Fax: 847-844-8796 www.newhavendisplay.com nhtech@newhavendisplay.com nhsales@newhavendisplay.com Document Revision History Revision 0 1 2 3 Date 3/23/2014 5/1/2015 10/20/15 2/22/17 Description Initial Release Interface Description Updated Mechanical Drawing Updated Thru-Hole Diameter Increased, Temperature Updated Functions and Features • • • • • 160 x 128 pixel resolution Built-in SEPS525 controller Parallel or Serial MPU interface Single, low voltage power supply RoHS compliant [2] Changed by AK PB SB SB Mechanical Drawing 1 2 Y R A T E I 3 4 A 5 Rev Description 6 Date A WW YY B B D Notes: R P O R C P RevB Newhaven Di spl ay NHD- 1. 69- 160128UGC3 C D 1. Display Type: 1.69” Color OLED 2. Driver IC: SEPS525 3. Interface: 8-Bit 68XX/80XX Parallel, 3/4-Wire SPI 4. Operating Temp: -40°C - +70°C 5. Storage Temp: -40°C - +85°C 1 2 Unit mm Gen. Tol. ±0.3 3 4 Date 02/07/17 5 Part Number: NHD-1.69-160128UGC3 6 The information contained herein is the exclusive property of Newhaven Display International, Inc. and shall not be copied, reproduced, and/or disclosed in any format without permission. [3] Interface Description Parallel Interface: Pin No. 1 2 3 4 5 Symbol GND VDD NC D/C R/W or /WR External Connection Power Supply Power Supply MPU MPU 6 E or /RD MPU 7-14 15 16 17 18 19 20 DB10 – DB17 GND /RES /CS GND PS CPU MPU Power Supply MPU MPU Power Supply MPU MPU Function Description Ground Supply Voltage for OLED and logic. No Connect Register select signal. D/C=0: Command, D/C=1: Data 6800-interface: Read/Write select signal, R/W=1: Read R/W: =0: Write 8080-interface: Active LOW Write signal. 6800-interface: Operation enable signal. Falling edge triggered. 8080-interface: Active LOW Read signal. 8-bit Bi-directional data bus lines. Ground Active LOW Reset signal. Active LOW Chip Select signal. Ground Parallel/Serial select. HIGH: Parallel. LOW: Serial Interface select. HIGH: 6800 interface. LOW: 8080 interface External Connection Power Supply Power Supply MPU Power Supply Power Supply MPU MPU Power Supply MPU MPU Power Supply MPU MPU Function Description Ground Supply Voltage for OLED and logic. No Connect Register select signal. D/C=0: Command, D/C=1: Data Ground Ground Serial Data Input signal. Serial Clock signal. Ground Active LOW Reset signal. Active LOW Chip Select signal. Ground Parallel/Serial select. HIGH: Parallel. LOW: Serial Interface select. HIGH: 6800 interface. LOW: 8080 interface Serial Interface: Pin No. 1 2 3 4 5-6 7-12 13 14 15 16 17 18 19 20 Symbol GND VDD NC D/C VSS GND SDI SCL GND /RES /CS GND PS CPU MPU Interface Pin Assignment Summary Bus Interface 8-bit 6800 8-bit 8080 4-wire SPI D17 D16 SCL SDI Data/Command Interface D15 D14 D13 D12 D11 D[17:10] D[17:10] Tie LOW [4] D10 E E /RD R/W R/W /WR Control Signals /CS D/C /CS D/C /CS D/C /CS D/C /RES /RES /RES /RES Wiring Diagrams [5] Electrical Characteristics Item Operating Temperature Range Storage Temperature Range Supply Voltage Supply Current (logic) Supply Current (display) Sleep Mode Current “H” Level input “L” Level input “H” Level output “L” Level output Optical Characteristics Optimal Viewing Angles Item Top Bottom Left Right Contrast Ratio Response Time Brightness Lifetime Rise Fall Symbol TOP TST Condition Absolute Max Absolute Max Min. -40 -40 Typ. - Max. +70 +85 Unit ⁰C ⁰C VDD IDD ICC IDD+ICC_SLEEP VIH VIL VOH VOL - 2.6 0.8 * VDD GND VDD - 0.4 GND 2.8 6 180 2 - 3.3 12 330 10 VDD 0.4 VDD 0.4 V mA mA mA V V V V Symbol ϕY+ ϕYθXθX+ CR TR TF LV - VDD=2.8V TOP = 25°C Condition TOP = 25°C Min. 80 80 80 80 70 10,000 Typ. 2000:1 10 10 90 - Max. - Unit ⁰ ⁰ ⁰ ⁰ µs µs 2 cd/m Hrs. 50% Checkerboard 90 cd/m², TOP =25°C, 50% Checkerboard Note: Lifetime at typical temperature is based on accelerated high-temperature operation. Lifetime is tested at average 50% pixels on and is rated as Hours until Half-Brightness. The Display OFF command can be used to extend the lifetime of the display. Luminance of active pixels will degrade faster than inactive pixels. Residual (burn-in) images may occur. To avoid this, every pixel should be illuminated uniformly. Controller information Built-in SEPS525 Controller. Please download specification at www.newhavendisplay.com/app_notes/SEPS525.pdf [6] Table of Commands [7] Timing Characteristics 6800-Series MCU Parallel Interface: [8] [9] 8080-Series MCU Parallel Interface: [10] [11] 4-wire SPI: [12] Example Initialization Sequence: void oled_Data_160128RGB(unsigned char Data) { GPIO_ResetBits(GPIOC, CS1); GPIO_SetBits(GPIOC, RS); GPIO_Write(GPIOB, Data); GPIO_ResetBits(GPIOC, RW); GPIO_SetBits(GPIOC, E1); GPIO_ResetBits(GPIOC, E1); } void oled_Command_160128RGB(unsigned char Data) { GPIO_ResetBits(GPIOC, CS1); GPIO_ResetBits(GPIOC, RS); GPIO_Write(GPIOB, Data); GPIO_ResetBits(GPIOC, RW); GPIO_SetBits(GPIOC, E1); GPIO_ResetBits(GPIOC, E1); } void OLED_Init_160128RGB(void) { int i,j; GPIO_ResetBits(GPIOC, RES); graphic_delay(500000); GPIO_SetBits(GPIOC, RES); graphic_delay(500000); oled_Command_160128RGB(0x04);// Set Normal Driving Current oled_Data_160128RGB(0x03);// Disable Oscillator Power Down graphic_delay(2000); oled_Command_160128RGB(0x04); oled_Data_160128RGB(0x00); graphic_delay(2000); // Enable Power Save Mode // Set Normal Driving Current // Disable Oscillator Power Down oled_Command_160128RGB(0x3B); oled_Data_160128RGB(0x00); oled_Command_160128RGB(0x02); oled_Data_160128RGB(0x01); oled_Command_160128RGB(0x03); oled_Data_160128RGB(0x90); // Set EXPORT1 Pin at Internal Clock // Oscillator operates with external resister. // Internal Oscillator On // Set Frame Rate as 120Hz [13] oled_Command_160128RGB(0x80); oled_Data_160128RGB(0x01); // Set Reference Voltage Controlled by External Resister oled_Command_160128RGB(0x08);// Set Pre-Charge Time of Red oled_Data_160128RGB(0x04); oled_Command_160128RGB(0x09);// Set Pre-Charge Time of Green oled_Data_160128RGB(0x05); oled_Command_160128RGB(0x0A);// Set Pre-Charge Time of Blue oled_Data_160128RGB(0x05); oled_Command_160128RGB(0x0B);// Set Pre-Charge Current of Red oled_Data_160128RGB(0x9D); oled_Command_160128RGB(0x0C);// Set Pre-Charge Current of Green oled_Data_160128RGB(0x8C); oled_Command_160128RGB(0x0D);// Set Pre-Charge Current of Blue oled_Data_160128RGB(0x57); oled_Command_160128RGB(0x10);// Set Driving Current of Red oled_Data_160128RGB(0x56); oled_Command_160128RGB(0x11);// Set Driving Current of Green oled_Data_160128RGB(0x4D); oled_Command_160128RGB(0x12);// Set Driving Current of Blue oled_Data_160128RGB(0x46); oled_Command_160128RGB(0x13); oled_Data_160128RGB(0xa0); oled_Command_160128RGB(0x14); oled_Data_160128RGB(0x01); oled_Command_160128RGB(0x16); oled_Data_160128RGB(0x76); // Set Color Sequence // Set MCU Interface Mode oled_Command_160128RGB(0x20); oled_Data_160128RGB(0x00); oled_Command_160128RGB(0x21); oled_Data_160128RGB(0x00); // Shift Mapping RAM Counter oled_Command_160128RGB(0x28); oled_Data_160128RGB(0x7F); // 1/128 Duty (0x0F~0x7F) oled_Command_160128RGB(0x29); oled_Data_160128RGB(0x00); // Set Mapping RAM Display Start Line (0x00~0x7F) oled_Command_160128RGB(0x06); oled_Data_160128RGB(0x01); // Display On (0x00/0x01) oled_Command_160128RGB(0x05); oled_Data_160128RGB(0x00); // Shift Mapping RAM Counter // Disable Power Save Mode // Set All Internal Register Value as Normal Mode [14] oled_Command_160128RGB(0x15); oled_Data_160128RGB(0x00); // Set RGB Interface Polarity as Active Low } int oled_160128RGB(void) { oled_Command_160128RGB(0x17); oled_Data_160128RGB(0x00); //set column start address // oled_Command_160128RGB(0x18); oled_Data_160128RGB(0x9F); //set column end address // oled_Command_160128RGB(0x19); oled_Data_160128RGB(0x00); //set row start address // oled_Command_160128RGB(0x1A); oled_Data_160128RGB(0x7F); //set row end address // oled_Command_160128RGB(0x22); //write to RAM command for (i=0;i 25⁰C, 5min -> 70⁰C, 30min = 1 cycle For 100 cycles 10-22Hz, 1.5mm amplitude. 22-500Hz, 1.5G 30min in each of 3 directions X,Y,Z 115mbar, 40hrs VS=800V, RS=1.5kΩ, CS=100pF One time Note 1: No condensation to be observed. Note 2: Conducted after 2 hours of storage at 25⁰C, 0%RH. Note 3: Test performed on product itself, not inside a container. Evaluation Criteria: 1: Display is fully functional during operational tests and after all tests, at room temperature. 2: No observable defects. 3: Luminance >50% of initial value. 4: Current consumption within 50% of initial value Precautions for using OLEDs/LCDs/LCMs See Precautions at www.newhavendisplay.com/specs/precautions.pdf Warranty Information and Terms & Conditions http://www.newhavendisplay.com/index.php?main_page=terms [18] Note +80⁰C , 96hrs 3 3