NHD-1.8-128160EF-CTXI#-F

NHD-1.8-128160EF-CTXI#-F TFT (Thin-Film Transistor) Liquid Crystal Display Module NHD1.8128160EFCTXI#F- Newhaven Display 1.8” Diagonal 128 x 160 Pixels (Portrait Mode) Model Built-in Controller White LED Backlight TFT 6:00 Optimal View, Wide Temperature RoHS Compliant FFC ZIF Connection Style Newhaven Display International, Inc. 2661 Galvin Court Elgin IL, 60124 Ph: 847-844-8795 Fax: 847-844-8796 www.newhavendisplay.com nhtech@newhavendisplay.com nhsales@newhavendisplay.com Document Revision History Revision 0 1 2 3 Date 9/11/2013 11/5/15 8/1/16 9/25/18 4 5 6 3/21/19 12/13/19 3/8/21 Description Initial Release Datasheet Reformat Mechanical Drawing Updated Mechanical Drawing, Backlight Characteristics, & Supply Current Updated Driver Updated From ILI9163C to ILI9163V Updated Response Time & Added Chromaticity Updated Silkscreen on FPC, Footnote for Backlight Drive Conditions, Typical Backlight Voltage & Quality Information Functions and Features • • • • • 128 x 160 pixels (portrait mode) LED backlight 2.8V power supply 8-bit Parallel interface Built-in ILI9163V controller [2] Changed by AK SB SB SB SB SB AS 1 A 2 3 Mechanical Drawing 4 5 6 SYMBOL 7 8 REVISION DATE A TOP-POL/31.23±0.2 A.A/28.03 0.3±0.3 (3.33) 22±0.5 Green Tear tape Back 1.8" TFT 128(RGB)*160 Front A.A/35.04 TOP-POL/37.79±0.2 LCD/41.42±0.2 RGB BL/46.75±0.2 D.S.T T=0.10MM 2.25±0.2 Except the double side tape D.S.T T=0.10MM NEWHAVEN DISPLAY WWYY NHD-1.8-128160EF-CTXI#-F_rev14 1.43±0.2 NEWHAVEN DISPLAY WWYY NHD-1.8-128160EF-CTXI#-F_rev14 B LCD/31.83±0.2 10±0.5 (3.27) 0.3±0.3 1.6±0.2 BL/34.7±0.2 B R TFT Pinout: 3 0. Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 W=0.35 24 1 P=0.5 11.5±0.1 30.19±0.2 (16.5) component area 0.3±0.05 8.95±0.2 single area 24 Stiffener 12.5±0.1 1 3±0.3 0.5±0.1 550R6 8.4±0.2 2.36±0.3 YU XL YD XR 3±0.5 D 17.63±0.3 tape tape 4.5±0.5 single area Stiffener 1 White silk on FPC YU XL YD XR 102 CONTACT SIDE C E F Notes: 1. Display Size: 2. Op�mal View: 3. Display Mode: 4. Driver IC: 5. Supply Voltage: 6. Backlight: 7. Luminance: 1 1.77” TFT 6:00 Transmissive /Normal White / An�-Glare ILI9163V 2.8 V White LED / 3.2 V / 30 mA (Typ) 350 cd/m² (Typ) 2 3 Symbol GND IOVDD VDD /CS /RST D/C /WR /RD DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 LED-A LED-K1 LED-K2 GND NC NC NC NC C D E Standard Tolerance: (Unless otherwise specified) Linear: ±0.3mm Unless otherwise specified: • Dimensions are in Millimeters • Third Angle Projection Drawing/Part Number: NHD-1.8-128160EF-CTXI#-F Drawn By: Drawn Date: A. Shah 3/5/2021 Approved By: Approved Date: Do Not Scale Drawing A. Shah 3/5/2021 Revision: 14 Size: A3 Scale: NS Sheet 1 of 1 This drawing is solely the property of Newhaven Display International, Inc. The information it contains is not to be disclosed, reproduced or copied in whole or part without written approval from Newhaven Display. 4 5 6 7 8 F Pin Description and Wiring Diagram Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Symbol GND IOVDD VDD /CS /RST D/C /WR /RD DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 LED-A LED-K1 LED-K2 GND NC NC NC NC External Connection Power Supply Power Supply Power Supply MPU MPU MPU MPU MPU MPU MPU MPU MPU MPU MPU MPU MPU Power Supply Power Supply Power Supply Power Supply - Function Description Ground Supply Voltage for Logic (2.8V) – Can be tied to VDD Supply Voltage for LCD (2.8V) Active LOW Chip Select signal Active LOW Reset signal Data / Command selection: ‘1’ = Data ; ‘0’ = Command Active LOW Write signal Active LOW Read signal 8-bit bi-directional data bus Backlight Anode (30mA @ 3.2V) Backlight Cathode (Ground) Backlight Cathode (Ground) Ground No Connect No Connect No Connect No Connect LCD connector: 24pin 0.5mm FFC connector. Molex P/N: 52435-2471 [4] Electrical Characteristics Item Operating Temperature Range Storage Temperature Range Supply Voltage for Logic Supply Voltage for LCD Supply Current “H” Level input “L” Level input “H” Level output “L” Level output Backlight Supply Current Backlight Supply Voltage Backlight Lifetime* Symbol TOP TST VDD IOVDD IDD VIH VIL VOH VOL ILED VLED - Condition Absolute Max Absolute Max VDD = 2.8V - ILED = 30 mA ILED = 30 mA TOP = 25° C Min. -20 -30 1.65 2.5 1 0.7*IOVDD GND 0.8*IOVDD GND Typ. 2.8 2.8 3 - Max. +70 +80 3.3 3.3 5 IOVDD 0.3*IOVDD IOVDD 0.2*IOVDD Unit °C °C V V mA V V V V 2.8 20,000 30 3.2 50,000 40 3.3 - mA V Hrs. *Backlight lifetime is rated as Hours until half-brightness, under normal operating conditions. The LED of the backlight is driven by current drain; drive voltage is for reference only. Drive voltage must be selected to ensure backlight current drain is below MAX level stated Optical Characteristics Optimal Viewing Angles Item Top Bottom Left Right Contrast Ratio Luminance Response Time (Rise + Fall) Red Green Chromaticity Blue White Symbol ϕY+ ϕYθXθX+ CR LV TR + TF XR YR XG YG XB YB XW YW Condition CR ≥ 10 ILED =30mA TOP = 25°C - Min. 400 290 0.558 0.304 0.248 0.550 0.095 0.035 0.233 0.275 Typ. 40 60 60 60 500 350 8 0.608 0.354 0.298 0.600 0.145 0.085 0.283 0.325 Max. 16 0.658 0.404 0.348 0.650 0.195 0.135 0.333 0.375 Controller Information Built-in ILI9163V controller. Please download specification at http://www.newhavendisplay.com/app_notes/ILI9163.pdf [5] Unit ⁰ ⁰ ⁰ ⁰ cd/m2 ms - Table of Commands [6] For Command Descriptions, please see: http://www.newhavendisplay.com/app_notes/ILI9163.pdf [7] Timing Characteristics Parallel 8-bit Bus [8] Reset Timing [9] Example Program Code void TFT_18E_Init(void) { GPIO_ResetBits(GPIOC, CS1); GPIO_SetBits(GPIOC, nRD); GPIO_ResetBits(GPIOC, nWR); GPIO_WriteBit(GPIOC, RES, Bit_RESET); delay(5); TFT_delay(10); GPIO_WriteBit(GPIOC, RES, Bit_SET); delay(100); TFT_delay(10); TFT_18E_Write_Command(0x11); TFT_delay(100); TFT_18E_Write_Command(0x26);TFT_18E_Write_Data(0x04); TFT_18E_Write_Command(0xF2);TFT_18E_Write_Data(0x00); TFT_18E_Write_Command(0xB1);TFT_18E_Write_Data(0x0A);TFT_18E_Write_Data(0x14); TFT_18E_Write_Command(0xC0);TFT_18E_Write_Data(0x0A);TFT_18E_Write_Data(0x00); TFT_18E_Write_Command(0xC1);TFT_18E_Write_Data(0x02); TFT_18E_Write_Command(0xC5);TFT_18E_Write_Data(0x2F);TFT_18E_Write_Data(0x3E); TFT_18E_Write_Command(0xC7);TFT_18E_Write_Data(0x40); TFT_18E_Write_Command(0x2A); TFT_18E_Write_Data(0x00); TFT_18E_Write_Data(0x00); TFT_18E_Write_Data(0x00); TFT_18E_Write_Data(0x7F); TFT_18E_Write_Command(0x2B); TFT_18E_Write_Data(0x00); TFT_18E_Write_Data(0x00); TFT_18E_Write_Data(0x00); TFT_18E_Write_Data(0x9F); TFT_18E_Write_Command(0x36);TFT_18E_Write_Data(0x48); TFT_18E_Write_Command(0x3A);TFT_18E_Write_Data(0xC5); TFT_18E_Write_Command(0x29); TFT_18E_Write_Command(0x2C); } /***************************************************************************************/ void TFT_18E_Write_Command(unsigned char command) { GPIO_ResetBits(GPIOC, RS); GPIO_Write(GPIOB, command); GPIO_ResetBits(GPIOC, nWR); GPIO_SetBits(GPIOC, nWR); } /***************************************************************************************/ void TFT_18E_Write_Data(unsigned char data1) { GPIO_SetBits(GPIOC, RS); GPIO_Write(GPIOB, data1); GPIO_ResetBits(GPIOC, nWR); GPIO_SetBits(GPIOC, nWR); } /***************************************************************************************/ [10] Quality Information Test Item Content of Test High Temperature storage Endurance test applying the high storage temperature for a long time. Endurance test applying the low storage temperature for a long time. Endurance test applying the electric stress (voltage & current) and the high thermal stress for a long time. Endurance test applying the electric stress (voltage & current) and the low thermal stress for a long time. Endurance test applying the electric stress (voltage & current) and the high thermal with high humidity stress for a long time. Endurance test applying the electric stress (voltage & current) during a cycle of low and high thermal stress. Endurance test applying vibration to simulate transportation and use. Endurance test applying electric static discharge. Low Temperature storage High Temperature Operation Low Temperature Operation High Temperature / Humidity Storage Thermal Shock resistance Vibration test Static electricity test Test Condition 2 -30⁰C , 96hrs 1,2 +70⁰C , 96hrs 2 -20⁰C , 96hrs 1,2 +50⁰C , 90% RH , 96hrs 1,2 -20℃ 30 min ~ +70℃ 30 min, 20 cycles 10-50Hz , 5G amplitude. 30 min in each of 3 directions X,Y,Z Air: ±8kV 150pF/330Ω, 5 Times Contact: ±4kV 150pF/330Ω, 5 Times Note 1: No condensation to be observed. Note 2: Conducted after 4 hours of storage at 25⁰C, 0%RH. Note 3: Test performed on product itself, not inside a container. Precautions for using LCDs/LCMs See Precautions at www.newhavendisplay.com/specs/precautions.pdf Warranty Information See Terms & Conditions at http://www.newhavendisplay.com/index.php?main_page=terms [11] Note +80⁰C , 96hrs 3