NHD-3.5-320240MF-ATXL#-1

NHD-3.5-320240MF-ATXL#-1 TFT (Thin-Film-Transistor) Color Liquid Crystal Display Module NHD3.5320240MFATXL#-1 Newhaven Display 3.5” Diagonal 320xRGBx240 Pixels Model Built-in Driver / No Controller White LED Backlight TFT 12:00 Optimal View, Wide Temperature RoHS Compliant Newhaven Display International, Inc. 2661 Galvin Ct. Elgin IL, 60124 Ph: 847-844-8795 Fax: 847-844-8796 www.newhavendisplay.com nhtech@newhavendisplay.com nhsales@newhavendisplay.com Document Revision History Revision 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Date 7/8/2009 7/29/2009 1/25/2011 3/31/2011 4/8/2011 12/10/2012 4/25/2014 5/30/2014 12/03/15 7/5/16 12/1/16 3/12/19 6/19/19 1/16/20 6/30/20 7/31/20 Description Initial Release MECHANICAL DRAWING UPDATE Viewing angle updated Pin description / Note section updated Contrast removed from electrical characteristics Timing characteristics updated Optical characteristics updated Driver information updated Backlight Lifetime Added, Datasheet Reformat Added Chromaticity VDD, IDD, and Chromaticity Updated ILED Updated and Drawing Repaired Backlight Characteristics Updated VLED Updated Revised Note on Manual Register Configuration Updated 2D Mechanical Drawing, Driver IC Part Number to NV3035GTC, Timing Charts & Quality Information Functions and Features • • • • 320xRGBx240 resolution LED backlight 3.3V power supply 24-bit Parallel digital RGB interface (6.4MHz) [2] Changed by CL CL AK AK BE AK ML AK SB SB SB SB SB SB AS AS 1 2 3 4 5 6 7 SYMBOL 8 REVISION DATE A A 76.9±0.2 72.88±0.15/Bezel opening (3.12) 0.3±0.3 2.12±0.2 72.28±0.3 TOP-POL (A,A70.08) 2.01±0.2 0.3±0.3 (3.41) 3.2±0.15 (38.45) RGB RGB B TEAR TAPE (29.4) (A,A52.56) 54.76±0.3 TOP-POL 55.36±0.15/Bezel opening 63.9±0.2 B NEWHAVEN DISPLAY WWYY NHD-3.5-320240MF-ATXL#-1 C C White silk on FPC NHD-3.5-320240MF_A 27.5±0.5 single side area (36.2) 5.5±0.5 D FPC out from the bottom 55.9±0.5 Component area 16.55±0.5 Protective Tape KA 16.55±0.5 single side area D Stiffener Contact Side 1 27.5±0.2 54.7±0.5 0.5±0.1 0.3±0.05 54 P0.5*53=26.5±0.05 4±0.3 0.35±0.05 2.25 0.2 0.5 15.7±0.3 W=0.35 E F NOTES: 1. Display Size: 2. Op�mal View: 3. Display Mode: 4. Driver IC: 5. Supply Voltage: 6. Backlight: 7. Lumimance: 1 0.125 0.35±0.03 3.5” TFT 12:00 Transmissive / Normally White / An�-Glare NV3035GTC 3.3V White LED / 19.2 V / 18 mA (Typ) 400 cd/m² (Typ) 2 3 E DETAIL:A STANDARD TOLERANCE: (UNLESS OTHERWISE SPECIFIED) LINEAR: ±0.3mm 5 6 1.0 NHD-3.5-320240MF-ATXL#-1 UNLESS OTHERWISE SPECIFIED: DRAWN BY: - DIMENSIONS ARE IN MILLIMETERS DRAWN DATE: - THIRD ANGLE PROJECTION 4 REVISION: DRAWING/PART NUMBER: A. Shah 7/31/20 APPROVED BY: SIZE: A3 A. Shah SCALE: APPROVED DATE: DO NOT SCALE DRAWING NS 7/31/20 SHEET 1 OF 1 THIS DRAWING IS SOLELY THE PROPERTY OF NEWHAVEN DISPLAY INTERNATIONAL, INC. THE INFORMATION IT CONTAINS IS NOT TO BE DISCLOSED, REPRODUCED OR COPIED IN WHOLE OR PART WITHOUT WRITTEN APPROVAL FROM NEWHAVEN DISPLAY. 7 8 F Pin Description Pin No. 1 2 3 4 5 6 7 8 9 10 11 12-19 20-27 28-35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 Symbol LED_K LED_K LED_A LED_A NC NC NC RSTB SPENB SPCK SPDA B0-B7 G0-G7 R0-R7 HSD VSD CLKIN NC NC VDD VDD NC NC NC NC NC NC NC NC NC DEN GND GND External Connection Power Supply Power Supply Power Supply Power Supply MPU MPU MPU MPU MPU MPU MPU MPU MPU MPU Power Supply Power Supply Power Supply Power Supply Function Description Backlight Cathode (Ground) Backlight Cathode (Ground) Backlight Anode (18mA @ 19.2V) Backlight Anode (18mA @ 19.2V) No Connect No Connect No Connect Active LOW Reset signal Active LOW Serial Chip Select signal Serial Clock signal Serial Data signal Blue Data signals Green Data signals Red Data signals Horizontal (Line) Sync signal Vertical (Frame) Sync signal Dot Clock signal No Connect No Connect Supply Voltage for LCD and logic (3.3V) Supply Voltage for LCD and logic (3.3V) No Connect No Connect No Connect No Connect No Connect No Connect No Connect No Connect No Connect Data Enable signal (No Connect) Ground Ground Recommended connector: 54pin, 0.5mm pitch, FFC connector. Molex P/N 51296-5494 [4] Electrical Characteristics Item Operating Temperature Range Storage Temperature Range Digital Supply Voltage Supply Current “H” Level input “L” Level input “H” Level output “L” Level output Backlight Supply Current Backlight Supply Voltage Backlight Lifetime* Symbol TOP TST VDD IDD VIH VIL VOH VOL Condition Absolute Max Absolute Max VDD =3.3V - Min. -20 -30 3.0 5 0.8 * VDD VSS VDD - 0.4 VSS Typ. 3.3 10 - Max. +70 +80 3.6 20 VDD 0.2 * VDD VDD VSS + 0.4 Unit ⁰C ⁰C V mA V V V V ILED VLED - ILED = 18mA TOP = 25° C 16.8 20,000 18 19.2 50,000 20 20.4 - mA V Hrs. *Backlight lifetime is rated as Hours until half-brightness, under normal operating conditions. The LED of the backlight is driven by current drain; drive voltage is for reference only. Drive voltage must be selected to ensure backlight current drain is below MAX level stated Optical Characteristics Optimal Viewing Angles Item Top Bottom Left Right Contrast Ratio Luminance Response Time Rise Fall Red Green Chromaticity Blue White Symbol ϕY+ ϕYθXθX+ CR LV Tr Tf XR YR XG YG XB YB XW YW Condition CR ≥ 10 ILED = 18 mA TOP=25°C - Min. 200 320 0.556 0.302 0.268 0.541 0.093 0.052 0.230 0.256 Typ. 60 40 60 60 350 400 25 25 0.606 0.352 0.318 0.591 0.143 0.102 0.280 0.306 Max. 40 40 0.656 0.402 0.368 0.641 0.193 0.152 0.330 0.356 Unit ⁰ ⁰ ⁰ ⁰ cd/m2 ms ms - Driver Information Built-in NV3035GTC driver. No controller. Please download specification at https://www.newhavendisplay.com/resources_dataFiles/datasheets/LCDs/NV3035GTC.pdf NOTE: Control registers accessible via the display’s 3-wire SPI interface are used to set optimal functionality of the driver IC and TFT panel during manufacturing of the display. These control registers are not intended for use during normal operation of the display. Changing these register values may result in undesired visual artifacts and improper functionality of the display. [5] Timing Characteristics Parameter Symbol Min. Typ. Max. System Operation Timing VDD Power Source Slew Time RSTB active pulse Width TPOR TRSTB 40 CLKIN clock time HSD to CLKIN HSD width VSD width HSD period time VSD setup time VSD hold time HSD setup time HSD hold time Data set-up time Data hold time DEN setup time Time that VSD to 1st line data input Tclk Thc Thwh Tvwh Th Tvst Tvhd Thst Thhd Tdsu Tdhd Tesd 35.7 1 1 60 8 10 8 10 8 10 12 63.56 - 1 67 - Tvs 2 13 127 Tvs 12 20 28 Tvs 17 25 33 1000 Unit Conditions us us From 0V to 90% VDD VDD = 3.3V ns CLKIN CLKIN Th us ns ns ns ns ns ns ns Th Please refer to timing table (P25) Input Output Timing DIN[23:0] to CLKIN DIN[23:0] to CLKIN DEN to CLKIN @C1R601/8bit RGB HV mode Control by HDLY[6:0] setting Tvs = HDLY[6:0] @CCIR656 NTSC mode Control by HDLY[6:0] setting Tvs = HDLY[6:0] @CCIR656 PAL mode Control by HDLY[6:0] setting Tvs = HDLY[6:0] @24bit RGB HV mode Control by HDLY[6:0] setting Tvs = HDLY[6:0] 96% final, CL=30pF, RL=2KΩ 96% final, CL=40pF 96% final, CL=33nF, RL=100Ω Time that CCIR_V to 1st line data input Time that CCIR_V to 1st line data input Time that VSD to 1st line data input Source output stable time 1 Gate output stable time VCOMOUT output stable time Tvs 2 13 127 Tst Tgst Tcst - 25 500 4 30 1000 8 Serial Clock SPCK pulse duty Serial data setup time Serial data hold time Serial clock high/low Chip select distinguish SPENA to VSD SPENB input setup time SPENB input hold time Tspck Tscdut Tisu Tihd Tssw Tcd Tcv Teck Tcke 320 40 120 120 120 1 1 150 150 50 - 60 - ns % ns ns ns us us Ns ns Parameter Symbol Min. Typ. Max. Unit Conditions CLKIN frequency CLKIN cycle time CLKIN pulse duty Time that HSD to 1st data input (NTSC) Fclk Tclk Tcwh 6.1 125 40 6.4 156 50 8.0 164 60 MHz ns % VDD=3.0~3.6V Ths 40 70 255 CLKIN DDLY=70,Offset=0(fixed) Th Th Th us ns us 3-wire serial communication AC timing [6] Tckh/Tspck Tclk Input Data Format Clock and Data Input Timing Diagram [7] 3-wire Timing Diagram Input Data Timing [8] Quality Information Test Item Content of Test High Temperature storage Endurance test applying the high storage temperature for a long time. Endurance test applying the low storage temperature for a long time. Endurance test applying the electric stress (voltage & current) and the high thermal stress for a long time. Endurance test applying the electric stress (voltage & current) and the low thermal stress for a long time. Endurance test applying the electric stress (voltage & current) and the high thermal with high humidity stress for a long time. Endurance test applying the electric stress (voltage & current) during a cycle of low and high thermal stress. Endurance test applying vibration to simulate transportation and use. Low Temperature storage High Temperature Operation Low Temperature Operation High Temperature / Humidity Operation Thermal Shock resistance Vibration test Static electricity test Test Condition Endurance test applying electric static discharge. 2 -30⁰C , 96hrs 1,2 +70⁰C , 96hrs 2 -20⁰C , 96hrs 1,2 +50⁰C , 90% RH , 96hrs 1,2 -20⁰C,60min -> 25⁰C,5min -> 70⁰C,60min = 1 cycle 20 cycles 10-50Hz , 5G Acceleration 60 sec in each of 3 directions (X,Y,Z) For 30 minutes Air: ±8kV 150pF/330Ω, 5 Times Contact: ±4kV 150pF/330Ω, 5 Times Note 1: No condensation to be observed. Note 2: Conducted after 4 hours of storage at 25⁰C, 0%RH. Note 3: Test performed on product itself, not inside a container. Precautions for using LCDs/LCMs See Precautions at www.newhavendisplay.com/specs/precautions.pdf Warranty Information and Terms & Conditions http://www.newhavendisplay.com/index.php?main_page=terms [9] Note +80⁰C , 96hrs 3