NHD-4.3CTP-SHIELD-N

NHD-4.3CTP-SHIELD-N Color TFT Liquid Crystal Display Module + Arduino Shield NHD4.3CTPSHIELDN- Newhaven Display 4.3” Diagonal Capacitive Touch Panel with Controller Arduino Shield Display: NHD-4.3-480272EF-ASXN#-CTP, Sunlight Readable Type, Wide Temperature Newhaven Display International, Inc. 2661 Galvin Ct. Elgin IL, 60124 Ph: 847-844-8795 Fax: 847-844-8796 www.newhavendisplay.com nhtech@newhavendisplay.com nhsales@newhavendisplay.com Document Revision History Revision 0 Date 08/17/16 Description Initial Release Changed by PB Functions and Features          480xRGBx272 resolution, up to 262K colors Sunlight Readable Utilizes the FTDI FT801 Embedded Video Engine PWM backlight control Onboard audio power amplifier microSD card reader (microSD card not included) Built-in logic level shifting Assembled with NHD-4.3-480272EF-ASXN#-CTP Capacitive touch panel with controller o 5 point multi-touch input o Gesture input  Zoom In/Out  Swipe Up/Down/Left/Right User Guide: Please download User Guide at http://www.newhavendisplay.com/userguides/NHD-4.3CTP-SHIELD_User_Guide.pdf [2] Mechanical Drawing 1 2 3 4 5 Rev 1.0 6 Description Initial Release Date 08/17/16 A A PCB 105.50 0.3 14 7.45 B 58.33 51.53 PCB 67.20 0.3 B 6 4.40 C D NOTES: 1. Display Size: 4.3” TFT 2. Optimal Viewing Direction: 6:00 3. Display Mode: Transmissive / Normally White / Anti-Glare 4. Luminance: 830 cd/m² 5. 3M Brightness Enhancement Film 6. Touch Panel: PCAP 1 2 C D Unit mm Gen. Tol. ±0.3 3 4 [3] Date 08/17/16 5 Model: NHD-4.3CTP-SHIELD-N 6 Schematic [4] Schematic [5] Schematic [6] Schematic [7] Pin Description Arduino UNO Pin Symbol J1 Interface SCL SDA AREF GND 13 12 11 10 9 8 J2 Interface 7 6 5 4 3 2 1 0 J3 Interface RESERVED IOREF RESET 3.3V 5V GND GND Vin J4 Interface A0 A1 A2 A3 A4 A5 J5 Interface MISO 5V SCK MOSI RESET GND Function Description No Connect No Connect No Connect Ground No Connect (Short SJ2 for SPI SCK signal) No Connect (Short SJ3 for SPI MISO signal) No Connect (Short SJ1 for SPI MOSI signal) FT801 Active LOW Chip Select signal FT801 Active LOW Host Interrupt signal FT801 Active LOW Power Down signal No Connect No Connect No Connect microSD Active LOW Chip Select signal No Connect No Connect No Connect No Connect No Connect No Connect No Connect No Connect Supply Voltage for Module (+5V) Ground Ground No Connect No Connect No Connect No Connect No Connect No Connect No Connect SPI MISO signal (Default) No Connect SPI SCK signal (Default) SPI MOSI signal (Default) No Connect Ground [8] Electrical Characteristics Item Operating Temperature Range Storage Temperature Range Supply Voltage Supply Current “H” level input “L” level input Symbol TOP TST VDD IDD VIH VIL Condition Absolute Max Absolute Max VDD = 5V - Min. -20 -30 4.8 2.2 GND Typ. 5.0 330 - Max. +70 +80 5.5 400 VDD 0.8 Unit ⁰C ⁰C V mA V V Symbol ϕY+ ϕYθXθX+ Cr Lv Tr Tf Condition Min. 400 660 - Typ. 50 70 70 70 500 830 25 25 Max. 30 30 Unit ⁰ ⁰ ⁰ ⁰ 2 cd/m ms ms Optical Characteristics Optimal Viewing Angles Item Top Bottom Left Right Contrast Ratio Luminance Response Time Rise Fall Cr ≥ 10 ILED = 40 mA TOP = 25°C - Capacitive Touch Panel Material Characteristics Property IC ITO Glass Thickness Surface Hardness Transparency Operating Humidity Storage Humidity Requirement FT5306DE4 0.55 ≥6 83% ± 5% 20~90 20~90 Unit mm H RH RH Controller Information TFT Controller: Built-in FTDI FT801 Embedded Video Engine. Please download specification at http://www.ftdichip.com/Support/Documents/DataSheets/ICs/DS_FT801.pdf Display Information TFT: NHD-4.3-480272EF-ASXN#-CTP - Sunlight Readable 4.3” TFT, 480x272 Pixels, 24-bit Parallel RGB Interface, w/ Projected Capacitive Touch Panel. Please download specification at http://www.newhavendisplay.com/specs/NHD-4.3-480272EF-ASXN-CTP.pdf [9] Block Diagram Host Interface SPI Interface – The SPI slave interface operates up to 30MHz. Only SPI mode 0 is supported. The SPI interface is selected by default (MODE pin is internally pulled low by a 100k resistor). [10] Timing Characteristics SPI Interface: For more information about FT801 controller please go to official FT801 Datasheet. http://www.ftdichip.com/Support/Documents/DataSheets/ICs/DS_FT801.pdf [11] Quality Information Test Item Content of Test High Temperature storage Endurance test applying the high storage temperature for a long time. Endurance test applying the low storage temperature for a long time. Endurance test applying the electric stress (voltage & current) and the high thermal stress for a long time. Endurance test applying the electric stress (voltage & current) and the low thermal stress for a long time. Endurance test applying the electric stress (voltage & current) and the high thermal with high humidity stress for a long time. Endurance test applying the electric stress (voltage & current) during a cycle of low and high thermal stress. Endurance test applying vibration to simulate transportation and use. Low Temperature storage High Temperature Operation Low Temperature Operation High Temperature / Humidity Operation Thermal Shock resistance Vibration test Static electricity test Test Condition Endurance test applying electric static discharge. 2 -30⁰C , 96hrs 1,2 +70⁰C , 96hrs 2 -20⁰C , 96hrs 1,2 +60⁰C , 90% RH , 96hrs 1,2 -20⁰C,30min -> 25⁰C,5min >70⁰C,30min = 1 cycle 10 cycles 10-55Hz , 15mm amplitude. 60 sec in each of 3 directions X,Y,Z For 15 minutes VS=800V, RS=1.5kΩ, CS=100pF One time Note 1: No condensation to be observed. Note 2: Conducted after 4 hours of storage at 25⁰C, 0%RH. Note 3: Test performed on product itself, not inside a container. Precautions for using LCDs/LCMs See Precautions at www.newhavendisplay.com/specs/precautions.pdf Warranty Information See Terms & Conditions at http://www.newhavendisplay.com/index.php?main_page=terms [12] Note +80⁰C , 96hrs 3