NHD-5.7-640480WF-CTXL#

NHD-5.7-640480WF-CTXL# TFT (Thin-Film-Transistor) Color Liquid Crystal Display Module NHD5.7640480WFCTXL# Newhaven Display 5.7” Diagonal 640xRGBx480 Pixels Model Built-in driver + Controller White LED Backlight TFT 6:00 Optimal View, Wide Temp RoHS Compliant Newhaven Display International, Inc. 2661 Galvin Ct. Elgin IL, 60124 Ph: 847-844-8795 Fax: 847-844-8796 www.newhavendisplay.com nhtech@newhavendisplay.com nhsales@newhavendisplay.com Document Revision History Revision 0 1 2 Date 3/9/2009 6/18/2012 4/25/17 Description Initial Release Pin description updated Optical Characteristics Updated Functions and Features     640xRGBx480 resolution LED backlight 8-bit parallel interface SSD1963 Controller [2] Changed by CL AK TM Mechanical Drawing 1 2 4 79.70 21.25 60.60 64.40 0.8 9.25 103.70 12.05 B 26.85 46.70 40.00 86.40(AA) 3.00 115.20(AA) 1.85 117.50(VA) 0.18 0.18 52.10 RGB 4-R0.8 C RGB 31.95 88.70(VA) Date 24.05 26.85 98.80±0.3 6 Description A 31.95 40.00 5 4.20 B C Rev 12 3.50 2.35 3.89 1.50 1.81 A 3 0.06 Dots Size 30/1 5.70 5.95 8.30MAX 125.00±0.3 D D Date 06/18/12 Unit Gen. Tolerance ±0.3mm 1 2 3 4 [3] mm 5 Model: NHD-5.7-640480WF-CTXL# 6 1 A 2 3 4 Rev 5 Date 21 CN2 A 16.00 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 4-PTH 22 32 1 CON1 1.00 1 1.00 1 28.6 24.5 Parts Area 24.0L*16.0W CN1 25.30 50 p0.5*49=24.50 0.50 44.9 46.9 0.30 50 1 (Down-Side) 50 3.00 1 38.70 CON2 CON3 B C 6 Description 79.60 GND VDD VO A0 R/W E DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 CS UD LR RST NC NC B C 20.10 D D Date 06/18/12 Unit Gen. Tolerance ±0.3mm 1 2 3 4 [4] mm 5 Model: NHD-5.7-640480WF-CTXL# 6 Pin Description Note: CON2 has a 20-pin, 1.0mm pitch, Top-Contact FFC Connector. Pins 21 and 22 are not connected. CON2: Pin No. 1 2 3 4 5 6 7-14 15 16 17 18 19 20 Symbol GND VCC NC D/C# WR# RD# [DB0-DB7] CS# U/D R/L RES# NC NC External Connection Power Supply Power Supply MPU MPU MPU MPU MPU MPU MPU MPU - Function Description Ground Power supply for LCD and logic (3.3V) No Connect Register Select signal – 0: Command, 1: Data Active LOW Write signal, 8080 MPU interface Active LOW Read signal, 8080 MPU interface Bi-directional data bus lines Active LOW Chip Select signal Scan direction 1: Up, 0: Down Scan direction 1: Right, 0: Left Active LOW Reset signal No Connect No Connect Recommended LCD connector: 1.0mm pitch 20-Conductor FFC. Molex p/n 52746-2070 Backlight: Pin No. 1 2 Symbol VCC VCC External Connection Power Supply Power Supply Function Description LED Anode (60mA @ 23.1V) LED Cathode Backlight connector: JST p/n: BHSR-02VS-1 Mates with: JST p/n: SM 02B-BHSS-1 [5] Controller Information Built-in SSD1963 controller. Please download specification at http://www.newhavendisplay.com/app_notes/SSD1963.pdf 8080 Mode Interface: The 8080 mode MPU interface consists of CS#, D/C, RD#, WR#, and DB[7:0]. This interface uses WR# to define a write cycle and RD# to define a read cycle. If the WR# goes LOW when the CS# signal is LOW, the data or command will be latched into the system at the rising edge of WR#. Similarly, the read cycle will start when RD# goes LOW and end at the rising edge of RD#. See the SSD1963 datasheet for detailed timing diagrams. Command Instructions: See the SSD1963 datasheet for the Instruction Table and Command Descriptions. Pixel Data Format: [6] Electrical Characteristics Item Operating Temperature Range Storage Temperature Range Supply Voltage Supply Current Backlight Supply Current Backlight Supply Voltage Backlight Lifetime Symbol Top Tst VCC ICC Condition Absolute Max Absolute Max VCC=3.3 Min. -20 -30 3.0 - Typ. 3.3 190 Max. +70 +80 3.6 250 Unit ⁰C ⁰C V mA IB VBL - 10,000 60 23.1 25,000 24.5 - mA V Hr Symbol Condition Cr ≥ 10 Cr ≥ 10 Cr ≥ 10 Cr ≥ 10 - Min. 150 250 - Typ. 40 60 60 60 250 300 25 25 Max. 40 40 Unit ⁰ ⁰ ⁰ ⁰ Optical Characteristics Item Viewing Angle – Top Viewing Angle – Bottom Viewing Angle – Left Viewing Angle – Right Contrast Ratio Luminance Response Time (rise) Response Time (fall) Cr YL Tr Tr [7] cd/m2 ms ms Quality Information Test Item Content of Test High Temperature storage Endurance test applying the high storage temperature for a long time. Endurance test applying the low storage temperature for a long time. Endurance test applying the electric stress (voltage & current) and the high thermal stress for a long time. Endurance test applying the electric stress (voltage & current) and the low thermal stress for a long time. Endurance test applying the electric stress (voltage & current) and the high thermal with high humidity stress for a long time. Endurance test applying the electric stress (voltage & current) during a cycle of low and high thermal stress. Endurance test applying vibration to simulate transportation and use. Low Temperature storage High Temperature Operation Low Temperature Operation High Temperature / Humidity Operation Thermal Shock resistance Vibration test Static electricity test Test Condition Endurance test applying electric static discharge. 2 -30⁰C , 200hrs 1,2 +70⁰C 200hrs 2 -20⁰C , 200hrs 1,2 +60⁰C , 90% RH , 96hrs 1,2 -20⁰C,30min -> 25⁰C,5min -> 70⁰C,30min = 1 cycle 10 cycles 10-55Hz , 15mm amplitude. 60 sec in each of 3 directions X,Y,Z For 15 minutes VS=800V, RS=1.5kΩ, CS=100pF One time Note 1: No condensation to be observed. Note 2: Conducted after 4 hours of storage at 25⁰C, 0%RH. Note 3: Test performed on product itself, not inside a container. Precautions for using LCDs/LCMs See Precautions at www.newhavendisplay.com/specs/precautions.pdf Warranty Information and Terms & Conditions http://www.newhavendisplay.com/index.php?main_page=terms [8] Note +80⁰C , 200hrs 3