NHD-7.0-800480EF-ATXV#-CTP

NHD-7.0-800480EF-ATXV#-CTP TFT (Thin-Film-Transistor) Color Liquid Crystal Display Module NHD7.0800480EFATXV#CTP- Newhaven Display 7.0” Diagonal 800xRGBx480 Pixels Model Built-in Driver / No Controller White LED Backlight TFT MVA Type, Wide Temperature RoHS Compliant Capacitive Touch Panel with Controller Newhaven Display International, Inc. 2661 Galvin Ct. Elgin IL, 60124 Ph: 847-844-8795 Fax: 847-844-8796 www.newhavendisplay.com nhtech@newhavendisplay.com nhsales@newhavendisplay.com Document Revision History Revision 0 1 2 3 Date 8/30/2013 4/1/2015 7/10/2015 3/16/16 Description Initial Release CTP mechanical dimensions updated Backlight characteristics updated Brightness Updated, Backlight Life Time Added, Datasheet Reformat, CTP Voltage Updated Functions and Features • • • • • 800xRGBx480 resolution LED backlight 24-bit digital RGB interface 16.7M colors Capacitive touch panel with controller o 5 point multi-touch input o Gesture input  Zoom In/Out  Swipe Up/Down/Left/Right [2] Changed by ML AK AK SB L A I Mechanical Drawing 3 4 BACK FRONT (49.70) T N E D I ACTIVE AREA CENTER 85.63 A.A 104±0.3 OUTLINE 800(RGB)*480 6.11 (7.26) TEAR TAPE 89.1P0.2/BZ OPENING 5.3 (6.889) 156.7±0.2/BZ OPENING 153.84 A.A (80.82) B 1 (39) 20.39±0.5 C 1 40 DETAIL A 4-R 2 4.5±0.5 0.3±0.05 CENTER LINE K .2 W=0.3±0.03 74.93±0.5 A 40 1 R0 O C Notes: 1. Display Size: 7” TFT 2. Viewing Direction: Full View 3. Display Mode: Transmissive / Normally White / Anti-Glare D 4. Driver IC: HX8264-D02 5. Power Supply Voltage: 3.3V 6. Backlight: White LED / 9.6 V / 160 mA (Typ) 7. Brightness: 290 cd/m² 8. Touch Panel: PCAP 1 2 Contact side F N COMPONENT AREA 3.5±0.3 1.75 0.3±0.03 (4) 15±1 71±0.5 (4) 4 COMPONENT AREA STIFFENER (PI) 1.5 Max. COVERLAYER OPEN 6 Description 4.9±0.4 165±0.3 A 5 Rev 36.04 2 COVERLAYER OPEN 1 P0.5X(40-1)=19.5±0.05 LED CIRCUIT 0.5±0.1 20.5±0.1 3*8=24EA,20mA*8=160mA DETAIL A (3:1) PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 Date SYMBOL LED-K LED-A GND VDD R0 R1 R2 R3 R4 R5 R6 R7 G0 G1 G2 G3 G4 G5 G6 G7 B0 B1 B2 B3 B4 B5 B6 B7 GND DCLK DISP HSYNC VSYNC DEN NC GND NC(XR) NC(YD) NC(XL) NC(YU) Date 03/16/16 Unit Gen. Tolerance ±0.3mm 3 4 mm 5 Model: NHD-7.0-800480EF-ATXV#-CTP 6 The drawing contained herein is the exclusive property of Newhaven Display International, Inc. and shall not be copied, reproduced, and/or disclosed in any format without permission. [3] A B C D Pin Description TFT: Pin No. 1 2 3 4 5-12 13-20 21-28 29 30 31 32 33 34 35 36 37 38 39 40 Symbol LED-K LED-A GND VDD [R0-R7] [G0-G7] [B0-B7] GND CLKIN DISP HSD VSD DEN NC GND NC(XR) NC(YD) NC(XL) NC(YU) Connection Power Supply Power Supply Power Supply Power Supply MPU MPU MPU Power Supply MPU MPU MPU MPU MPU Power Supply - Function Description Backlight Cathode Backlight Anode (160mA @ 9.6V) Ground Power Supply (+3.3V) Red Data Signals Green Data Signals Blue Data Signals Ground Clock for input data Display ON/OFF, DISP=1 : Display ON Line synchronization signal Frame synchronization signal Data Enable signal No Connect Ground No Connect No Connect No Connect No Connect LCD connector: 0.5mm pitch 40-Conductor FFC. Molex p/n: 54104-4031 (top contact) Backlight connector: on LCD connector Mates with: --- Capacitive Touch Panel: Pin No. 1 2 3 4 5 6 Symbol VDD GND SCL SDA /INT /RESET External Connection Power Supply Power Supply MPU MPU MPU MPU Function Description Power Supply (3.0V) Ground Serial I2C Clock (Requires pull-up resistor) Serial I2C Data (Requires pull-up resistor) Interrupt signal from touch panel module to host Active LOW Reset signal. Recommended connector: 1.0mm pitch 6-Conductor FFC. Molex p/n: 52271-0679 Driver/Controller Information TFT: Built-in HX8264-D02 Source Driver: http://www.newhavendisplay.com/app_notes/HX8264-D02.pdf Built-in HX8664-B Gate Driver: http://www.newhavendisplay.com/app_notes/HX8664-B.pdf Capacitive Touch Panel: Built-in FocalTech FT5406 controller. Please download specification at http://www.newhavendisplay.com/app_notes/FT5x06.pdf [4] Electrical Characteristics TFT: Item Operating Temperature Range Storage Temperature Range Supply Voltage Supply Current “H” Level Input “L” Level Input “H” Level Output “L” Level Output Backlight Supply Voltage Backlight Supply Current Backlight Lifetime* Symbol Top Tst VDD IDD VIH VIL VOH VOL Condition Absolute Max Absolute Max o VDD=3.3V 25 C - Min. -20 -30 3.0 60 0.7*VDD GND VDD-0.4 - Typ. 3.3 85 - Max. +70 +80 3.6 120 VDD 0.3*VDD GND+0.4 Unit ⁰C ⁰C V mA V V V V VLED ILED - VLED=9.6V ILED = 160 mA Top = 25° C 8.7 20,000 9.6 160 50,000 9.9 - V mA hrs. *Backlight lifetime is rated as Hours until half-brightness, under normal operating conditions. Capacitive Touch Panel: Item Operating Temperature Range Storage Temperature Range Supply Voltage Supply Current – Operating Supply Current – Hibernate “H” Level Input “L” Level Input “H” Level Output “L” Level Output Symbol Top Tst VDD IDD IDD Vih Vil Voh Vol Optical Characteristics Optimal Viewing Angles Item Top Bottom Left Right Contrast Ratio Luminance Response Time Rise Fall Condition Absolute Max Absolute Max Ta=25°C, VDD=3.3V Ta=25°C, VDD=3.3V - Symbol ϕY+ ϕYθXθX+ Cr L Tr Tf Condition Cr ≥10 - Min. -20 -30 2.8 0.7*VDD VSS 0.7*VDD VSS Min. 230 - Capacitive Touch Panel Material Characteristics: Property IC ITO Glass thickness Surface Hardness Light transmission Operating Humidity Storage Humidity Requirement FT5406EE8 0.55 ≥6 83% ± 5% 20~90 20~90 Unit mm H RH RH [5] Typ. 3.3 6.0 1.0 - Typ. 75 75 75 75 400 290 25 25 Max. +70 +80 3.6 VDD 0.3*VDD VDD 0.3*VDD Unit ⁰C ⁰C V mA uA V V V V Max. 35 35 Unit ⁰ ⁰ ⁰ ⁰ 2 cd/m ms ms Capacitive Touch Panel Registers Address Name B7 B6 B5 B4 00h DEVICE_MODE 01h GEST_ID 02h TD_STATUS 03h TOUCH1_XH Event Flag 04h TOUCH1_XL 1st Touch X Position LSB [7..0] 05h TOUCH1_YH Touch ID [3..0] 06h TOUCH1_YL 1st Touch Y Position LSB [7..0] B3 B2 B1 B0 Device Mode [2..0] Access R/W Gesture ID [7..0] R Touch Points [3..0] 1st Touch X Position MSB [11..8] R R R 1st Touch Y Position MSB [11..8] R R 07h R 08h R 09h TOUCH2_XH Event Flag 2nd Touch X Position MSB [11..8] 0Ah TOUCH2_XL 2nd Touch X Position LSB [7..0] 0Bh TOUCH2_YH Touch ID [3..0] 0Ch TOUCH2_YL 2nd Touch Y Position LSB [7..0] R R 2nd Touch Y Position MSB [11..8] R R 0Dh R 0Eh R 0Fh TOUCH3_XH Event Flag 3rd Touch X Position MSB [11..8] 10h TOUCH3_XL 3rd Touch X Position LSB [7..0] 11h TOUCH3_YH Touch ID [3..0] 12h TOUCH3_YL 3rd Touch Y Position LSB [7..0] R R 3rd Touch Y Position MSB [11..8] R R 13h R 14h R 15h TOUCH4_XH Event Flag 4th Touch X Position MSB [11..8] 16h TOUCH4_XL 4th Touch X Position LSB [7..0] 17h TOUCH4_YH Touch ID [3..0] 18h TOUCH4_YL 4th Touch Y Position LSB [7..0] R R 4th Touch Y Position MSB [11..8] R R 19h R 1Ah R 1Bh TOUCH5_XH Event Flag 5th Touch X Position MSB [11..8] 1Ch TOUCH5_XL 5th Touch X Position LSB [7..0] 1Dh TOUCH5_YH Touch ID [3..0] 1Eh TOUCH5_YL 5th Touch Y Position LSB [7..0] R 5th Touch Y Position MSB [11..8] 1Fh R R R R [6] Address Name B7 B6 B5 B4 B3 B2 B1 B0 80h ID_G_THGROUP valid touching detect threshold R/W 81h ID_G_THPEAK valid touching peak detect threshold R/W 82h ID_G_THCAL the threshold when calculating the focus of touching R/W 83h ID_G_THWATER the threshold when there is surface water R/W 84h ID_G_TEMP the threshold of temperature compensation R/W 85h ID_G_THDIFF the threshold whether the coordinate is different from original R/W 86h ID_G_CTRL Power Control Mode [1..0] R/W 87h ID_G_TIME_ENTER_MONITOR 88h ID_G_PERIODACTIVE 89h ID_G_PERIODMONITOR the timer of entering idle when in monitor status R/W A0h ID_G_AUTO_CLB_MODE auto calibration mode R/W A1h ID_G_LIB_VERSION_H Firmware Library Version H byte R A2h ID_G_LIB_VERSION_L Firmware Library Version L byte R A3h ID_G_CIPHER Chip vendor ID R A4h ID_G_MODE the interrupt status to host R A5h ID_G_PMODE Power Consume Mode A6h ID_G_FIRMID Firmware ID A7h ID_G_STATE Running State A8h ID_G_FT5201ID CTPM Vendor ID R A9h ID_G_ERR Error Code R AAh ID_G_CLB Configure TP module during calibration in Test Mode R/W FEh LOG_MSG_CNT The log MSG count R FFh LOG_CUR_CHA Current character of log message R the timer for entering monitor status Period Active [3..0] Access R/W R/W R NOTE: Registers 80h – AFh have been configured for optimum settings and do not need to be modified. [7] Register No 00h 01h 02h 03h Register Name Device Mode Gesture ID Touch Points Touch 1 Event Flag Bits [2:0] [7:0] [3:0] [7:6] Value 000b Description Normal Operating Mode 100b Test Mode - read raw data (reserved) 001b 48h System Information Mode (reserved) Zoom In 49h Zoom Out 00h No Gesture 000b 0 touch points detected 001b 1 touch point detected 010b 2 touch points detected 011b 3 touch points detected 100b 4 touch points detected 101b 5 touch points detected 00b Put Down 01b Put Up 10b Contact 11b Reserved 03h TOUCH1_XH [3:0] 0h - 1h Upper 4 bits of X touch coordinate 04h TOUCH1_XL [7:0] 00h - FFh Lower 8 bits of X touch coordinate 05h TOUCH1_YH [3:0] 0h - 1h Upper 4 bits of Y touch coordinate 06h TOUCH1_YL [7:0] 00h - FFh Lower 8 bits of Y touch coordinate 09h Touch 2 Event Flag [7:6] 00b Put Down 01b Put Up 10b Contact 11b Reserved 09h TOUCH2_XH [3:0] 0h - 1h Upper 4 bits of X touch coordinate 0Ah TOUCH2_XL [7:0] 00h - FFh Lower 8 bits of X touch coordinate 0Bh TOUCH2_YH [3:0] 0h - 1h Upper 4 bits of Y touch coordinate 0Ch TOUCH2_YL [7:0] 00h - FFh Lower 8 bits of Y touch coordinate 0Fh Touch 3 Event Flag [7:6] 00b Put Down 01b Put Up 10b Contact 11b Reserved 0Fh TOUCH3_XH [3:0] 0h - 1h Upper 4 bits of X touch coordinate 10h TOUCH3_XL [7:0] 00h - FFh Lower 8 bits of X touch coordinate 11h TOUCH3_YH [3:0] 0h - 1h Upper 4 bits of Y touch coordinate 12h 15h TOUCH3_YL Touch 4 Event Flag [7:0] [7:6] 00h - FFh 00b Lower 8 bits of Y touch coordinate Put Down 01b Put Up 10b Contact 11b Reserved 15h TOUCH4_XH [3:0] 0h - 1h Upper 4 bits of X touch coordinate 16h TOUCH4_XL [7:0] 00h - FFh Lower 8 bits of X touch coordinate 17h TOUCH4_YH [3:0] 0h - 1h Upper 4 bits of Y touch coordinate 18h TOUCH4_YL [7:0] 00h - FFh Lower 8 bits of Y touch coordinate [8] Register No Register Name Bits Value Description 1Bh Touch 5 Event Flag [7:6] 00b Put Down 01b Put Up 10b Contact 11b Reserved 1Bh TOUCH5_XH [3:0] 0h - 1h Upper 4 bits of X touch coordinate 1Ch TOUCH5_XL [7:0] 00h - FFh Lower 8 bits of X touch coordinate 1Dh TOUCH5_YH [3:0] 0h - 1h Upper 4 bits of Y touch coordinate 1Eh TOUCH5_YL [7:0] 00h - FFh Lower 8 bits of Y touch coordinate 80h ID_G_THGROUP [7:0] 00h - FFh Valid touching detect threshold Recommended: 46h Actual value will be 4 times register’s value 81h ID_G_THPEAK [7:0] 00h - FFh valid touching peak detect threshold Recommended: 3Ch 82h ID_G_THCAL [7:0] 00h - FFh Touch focus threshold Recommended: 1Dh 83h 84h ID_G_THWATER [7:0] 00h - FFh threshold when there is surface water Recommended: D3h ID_G_THTEMP [7:0] 00h- FFh threshold of temperature compensation Recommended: EBh 85h ID_G_THDIFF [7:0] 00h- FFh Touch difference threshold Recommended: A0h Actual value is 32 times the register’s value 86h ID_G_CTRL [1:0] 00h Power Control Mode: Not Auto Jump 01h Power Control Mode: Auto Jump 87h ID_G_TIME_ENTER_MONITOR [7:0] 00h-FFh Delay to enter 'Monitor' status (s) Recommended: C8h 88h ID_G_PERIODACTIVE [3:0] 3h-Eh Period of 'Active' status (ms) Recommended: 6h 89h ID_G_PERIODMONITOR [7:0] 1Eh-FFh Timer to enter ‘idle’ when in 'Monitor' (ms) Recommended: 28h A0h ID_G_AUTO_CLB_MODE [7:0] 00h Auto calibration mode: Enable auto calibration FFh Auto calibration mode: Disable auto calibration A1h ID_G_LIB_VERSION_H [7:0] 30h Firmware Library Version H byte A2h ID_G_LIB_VERSION_L [7:0] 01h Firmware Library Version L byte A3h ID_G_CIPHER [7:0] 06h Chip vendor ID A4h ID_G_MODE [0:0] 00h Interrupt status: Enable interrupt to host 01h Interrupt status: Disable interrupt to host 00h 'Active' Mode 01h 'Monitor' Mode 03h 'Hibernate' Mode A5h ID_G_PMODE [1:0] A6h ID_G_FIRMID [7:0] 30h Firmware ID A7h ID_G_STATE [7:0] 00h Running State: Configure 01h Running State: Work 02h Running State: Calibration 03h Running State: Factory 04h Running State: Auto-calibration A8h ID_G_FT5201ID [7:0] 98h CTPM Vendor's Chip ID A9h ID_G_ERR [7:0] 00h Error Code: OK 03h Error Code: Chip register writing inconsistent with reading 05h Error Code: Chip start fail 1Ah Error Code: Calibration match fail [9] Timing Characteristics – TFT Display Horizontal Timing Vertical Timing [10] Horizontal Timing Vertical Timing [11] Parallel 24-bit RGB mode Input Clock and Data Timing Source Output Timing [12] Vertical Timing HV (Cascade) Vertical Timing DE (Cascade) Gate Output Timing (Cascade) [13] Vertical Timing HV (Dual Gate) Vertical Timing DE (Dual Gate) Gate Output Timing (Dual Gate) [14] Power ON/OFF Sequence Enter/Exit Standby Mode Sequence [15] Timing Characteristics – Capacitive Touch Panel Data Transfer Format [16] Power ON Sequence Reset Sequence [17] Sample code to read touch data: i2c_start(); i2c_tx(0x70); i2c_tx(0x00); i2c_stop(); //Slave Address (Write) //Start reading address i2c_start(); i2c_tx(0x71); //Slave Address (Read) for(i=0x00;i 80⁰C, 30min, Change time: 5min, 10 cycles 10-55Hz , 1.5mm amplitude. 60 sec in each of 3 directions X,Y,Z For 15 minutes VS=800V, RS=1.5kΩ, CS=100pF One time Precautions for using LCDs/LCMs See Precautions at www.newhavendisplay.com/specs/precautions.pdf Warranty Information and Terms & Conditions http://www.newhavendisplay.com/index.php?main_page=terms [19] Note +80⁰C , 96hrs 3