NHD-C12864WM-09-FSW-FBW-3V3-M

厂商：
NEWHAVEN
封装：
-
描述：
LCD COG GRAPHIC 128X64 TRANSFL

数据手册：

下载NHD-C12864WM-09-FSW-FBW-3V3-M.pdf

立即购买

详情介绍
数据手册
价格&库存

NHD-C12864WM-09-FSW-FBW-3V3-M 数据手册

NHD‐C12864WM‐09‐FSW‐FBW‐3V3‐M COG (Chip‐On‐Glass) Liquid Crystal Display Module NHD‐ C12864‐ WM‐ F‐ SW‐ F‐ B‐ W‐ 3V3‐ M‐ Newhaven Display 128 x 64 pixels Model Transflective Side White LED backlight FSTN (+) 6:00 view Wide Temp (‐20°C ~ +70°C) 3Vdd, 3Volt Backlight Mounting Holes RoHS Compliant Newhaven Display International, Inc. 2511 Technology Drive, Suite 101 Elgin IL, 60124 Ph: 847‐844‐8795 Fax: 847‐844‐8796 www.newhavendisplay.com nhtech@newhavendisplay.com nhsales@newhavendisplay.com [1] Document Revision History Revision 0 1 2 3 4 5 Date 1/22/2007 8/7/2009 10/13/2009 2/16/2010 2/19/2010 5/14/2010 Description Initial Release User guide reformat Updated Electrical Characteristic Mechanical drawing updated Block diagram updated Electrical Characteristic update Functions and Features • • • • • 128 x 64 pixels Built‐in SPLC501C controller Parallel/Serial mode 1/64 duty cycle; 1/9 bias RoHS Compliant [2] Changed by ‐ BE MC BE BE MP Front Back Specification: 1). Driving: Duty: 1/64, 1/9 Bias, Vlcd: 9.5V 2). Viewing Direction: 6 O’Clock 3). Display mode: FSTN/Positive/Transflective 4). Operating Temp.: -20 oC ~ +70oC Storage Temp.: -30 oC ~ +80oC 5). Driver: SPL5010C 6). Unmarked Tolerances: + 0.2mm 7). Backlight: Side White NHD-C12864WM-09-FSW-FBW-3V3-M Newhaven Display Pin Description and Wiring Diagram Pin No. Symbol 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 A K CS2 RESETB RS RW E DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 VSS2 VOUT CAP3‐ CAP1+ CAP1‐ CAP2‐ CAP2+ VSS VDD V1 V2 V3 V4 V5 VR C86 PS External Connection MPU MPU MPU MPU MPU MPU MPU MPU MPU MPU MPU MPU MPU Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply ‐ MPU MPU Power Supply Power Supply Function Description Active HIGH chip select Active LOW Reset signal Register select signal. RS=0: Command, RS=1: Data Read/write select signal. R/W=1: Read R/W=0: Write Operation enable signal. Falling edge triggered. Parallel Interface DB0‐DB7: Bi‐directional 8‐bit data bus Serial Interface: DB0‐DB5: No connect in serial mode DB6= Serial clock (CLK) DB7= Serial data input (SDA) Ground (reference for voltage step‐up circuit) Connect to 1uF cap to VSS2 (PIN‐14) Connect to 1uF cap to CAP1+ (PIN‐17) Connect to 1uF cap to CAP3‐(PIN16) and CAP1‐(PIN18) Connect to 1uF cap to CAP1+ (PIN‐17) Connect to 1uF cap to CAP2+ (PIN‐20) Connect to 1uF cap to CAP2‐ (PIN‐19) Ground Power supply for LCD and logic (3.0V) 1.0uF‐2.2uF cap to VDD 1.0uF‐2.2uF cap to VDD 1.0uF‐2.2uF cap to VDD 1.0uF‐2.2uF cap to VDD 1.0uF‐2.2uF cap to VDD No Connect Select MPU interface pin. C86=H: 6800; C86=L: 8080 Parallel/Serial select. PS= H: Parallel; PS=L: Serial Power supply for LED Backlight (+3.0V) Ground for Backlight Recommended LCD connector: 0.5mm Pitch, 30 pin FFC. Molex p/n: 52892‐3095 Backlight connector: A2001H‐2P Mates with: A2001WR‐S‐2P [4] Electrical Characteristics Item Operating Temperature Range Storage Temperature Range Supply Voltage Supply Current Supply for LCD (contrast) “H” Level input “L” Level input “H” Level output “L” Level output LED Backlight voltage LED Backlight current Symbol TOP TST VDD IDD Condition Absolute Max Absolute Max Min. ‐20 ‐30 2.4 0.6 ‐ 0.7VDD Vss ‐ ‐ Typ. ‐ ‐ 3.3 ‐ ‐ ‐ ‐ ‐ ‐ VDD-V0 - Vih Vil VLED ILED ‐ VLED=3.0 ‐ ‐ Condition CR 2 CR 2 Min. ‐60 ‐40 ‐ ‐ ‐ VDD=3.3v 3.0 10 Max. +70 +80 5.5 1.0 9.5 VDD 0.3VDD ‐ ‐ 3.5 20 Unit ⁰C ⁰C V mA V V V ‐ ‐ V mA Typ. ‐ 6 150 150 Max. +35 +40 ‐ 250 250 Unit ⁰ ⁰ ‐ ms ms Optical Characteristics Item Viewing Angle ‐ Vertical Viewing Angle ‐ Horizontal Contrast Ratio Response Time (rise) Response Time (fall) Symbol θ Φ CR Tr Tf [5] Controller Information Built‐in SPLC501C. Download specification at http://www.newhavendisplay.com/app_notes/SPLC501C.pdf [6] [7] Table of Commands [8] [9] Example Initialization Program '‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ Sub Init Reset P3.7 'set Read/write to '0' for write Reset P3.0 'RS Set P3.1 'reset Reset P3.4 'E 'Set P3.3 'Reset P3.3 Waitms 2 'Set P3.3 Waitms 20 A = &HA2 '1/9 BIAS Call Writecom A = &HA0 'ADC SELECT , NORMAL Call Writecom A = &HC8 'COM OUTPUT REVERSE Call Writecom A = &HA4 'DISPLAY ALL POINTS NORMAL Call Writecom A = &H40 'DISPLAY START LINE SET Call Writecom A = &H25 'INTERNAL RESISTOR RATIO Call Writecom A = &H81 'ELECTRONIC VOLUME MODE SET Call Writecom A = &H10 'ELECTRONIC VOLUME Call Writecom A = &H2F 'POWER CONTROLLER SET Call Writecom A = &HAF 'DISPLAY ON Call Writecom End Sub '‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ Sub Writecom Reset P3.0 'A0 low Reset P3.7 'R/W low Set P3.6 'CS2 Set P3.4 'E P1 = A Reset P3.4 Reset P3.6 Reset P3.7 End Sub Sub Writedata Set P3.0 'A0 high Reset P3.7 'R/W low Set P3.6 'CS2 Set P3.4 'E P1 = A Reset P3.4 Reset P3.6 Reset P3.7 End Sub '‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ [10] Quality Information Test Item Content of Test High Temperature storage Endurance test applying the high storage temperature for a long time. Endurance test applying the low storage temperature for a long time. Endurance test applying the electric stress (voltage & current) and the high thermal stress for a long time. Endurance test applying the electric stress (voltage & current) and the low thermal stress for a long time. Endurance test applying the electric stress (voltage & current) and the high thermal with high humidity stress for a long time. Endurance test applying the electric stress (voltage & current) during a cycle of low and high thermal stress. Endurance test applying vibration to simulate transportation and use. Low Temperature storage High Temperature Operation Low Temperature Operation High Temperature / Humidity Operation Thermal Shock resistance Vibration test Static electricity test Test Condition Endurance test applying electric static discharge. 2 ‐30⁰C , 48hrs 1,2 +70⁰C 48hrs 2 ‐20⁰C , 48hrs 1,2 +40⁰C , 90% RH , 48hrs 1,2 ‐0⁰C,30min ‐> 25⁰C,5min ‐> 50⁰C,30min = 1 cycle 10 cycles 10‐55Hz , 15mm amplitude. 60 sec in each of 3 directions X,Y,Z For 15 minutes VS=800V, RS=1.5kΩ, CS=100pF One time Note 1: No condensation to be observed. Note 2: Conducted after 4 hours of storage at 25⁰C, 0%RH. Note 3: Test performed on product itself, not inside a container. Precautions for using LCDs/LCMs See Precautions at www.newhavendisplay.com/specs/precautions.pdf Warranty Information and Terms & Conditions http://www.newhavendisplay.com/index.php?main_page=terms [11] Note +80⁰C , 48hrs 3

下载 PDF

NHD-C12864WM-09-FSW-FBW-3V3-M

物料型号： - 型号：NHD-C12864WM-09-FSW-FBW-3V3-M - 制造商：Newhaven Display International, Inc.

器件简介： - 该模块是一个128 x 64像素的液晶显示屏，具有内置的SPLC501C控制器。 - 支持并行/串行模式。 - 具有1/64占空比和1/9偏压。 - 符合RoHS标准。

引脚分配： - 引脚1至引脚30的功能描述，例如： - 引脚1：CS2，微处理器的片选信号。 - 引脚2：RESETB，微处理器的复位信号。 - 引脚3：RS，寄存器选择信号。 - 引脚4：RW，读写选择信号。 - 引脚5：E，操作使能信号。 - 引脚6至引脚7：DBO和DB1，数据总线。 - 引脚14至引脚27：VSS2至V5，电源引脚。 - 引脚28至引脚30：VR、C86和PS，分别用于未连接、选择微处理器接口和选择并行/串行模式。

参数特性： - 工作温度范围：-20°C ~ +70°C - 存储温度范围：-30°C ~ +80°C - 供电电压：2.4V ~ 5.5V - 供电电流：在3.3V供电时，典型值为1.0mA - 液晶供电：9.5V - 输入高电平：0.7VDD ~ VDD - 输入低电平：Vss ~ 0.3VDD - LED背光电压：3.0V ~ 3.5V - LED背光电流：在3.0V背光电压时，典型值为10mA ~ 20mA

功能详解： - 模块具有128 x 64像素的显示能力。 - 内置SPLC501C控制器，支持并行和串行接口。 - 支持1/64占空比和1/9偏压。 - 具有侧白LED背光，符合RoHS标准。

应用信息： - 推荐使用0.5mm间距、30针FFC的LCD连接器，例如Molex型号52892-3095。 - 背光连接器为A2001H-2P，配对型号为A2001WR-S-2P。

封装信息： - 模块的尺寸和引脚布局信息，以及相关的公差和批准信息。

NHD-C12864WM-09-FSW-FBW-3V3-M 价格&库存

-> 查询更多价格&库存

很抱歉，暂时无法提供与“NHD-C12864WM-09-FSW-FBW-3V3-M”相匹配的价格&库存，您可以联系我们找货

免费人工找货

搜索历史

NHD-C12864WM-09-FSW-FBW-3V3-M

相关技术文章