NHD-C12865AR-FSW-GBW

NHD-C12865AR-FSW-GBW COG (Chip-On-Glass) Liquid Crystal Display Module NHDC12865ARFSWGBW- Newhaven Display 128 x 65 Pixels Model Transflective Side White LED Backlight STN Positive, Gray 6:00 Optimal View Wide Temperature RoHS Compliant Newhaven Display International, Inc. 2661 Galvin Court Elgin IL, 60124 Ph: 847-844-8795 Fax: 847-844-8796 www.newhavendisplay.com nhtech@newhavendisplay.com nhsales@newhavendisplay.com Document Revision History Revision 0 1 2 3 4 5 Date 9/12/2011 4/4/2013 3/17/2015 11/30/16 9/6/19 1/15/21 Description Initial Release Backlight mating connector updated Pin Description updated Mechanical Drawing, Electrical & Optical Char. Updated Mechanical Drawing & Backlight Characteristics Updated Updated 2D Mechanical Drawing Notes Functions and Features • • • • • • 128 x 65 pixels Built-in ST7565R controller +3.3V power supply 1/65 duty cycle; 1/9 bias Parallel/Serial Interface RoHS Compliant [2] Changed by AK RM SB SB AS 1 A 2 Mechanical Drawing 3 4 5 6 SYMBOL 7 8 REVISION DATE A B B NEWHAVEN DISPLAY NHD-C12865AR-FSW-GBW WW/YY C C D D E F Notes: 1. Driver: 2. Voltage: 3. Display Mode: 4. Op�mal View: 5. Backlight: 6. Driver IC: 7. Liner: 1 E 1/65 Duty, 1/9 Bias 3.3V VDD, 9.5 VLCD STN Posi�ve / Gray / Transflec�ve 6:00 White ST7565R Black Line on Glass Liner 2 3 STANDARD TOLERANCE: (UNLESS OTHERWISE SPECIFIED) LINEAR: ±0.3mm 5 6 1.0 NHD-C12865AR-FSW-GBW UNLESS OTHERWISE SPECIFIED: DRAWN BY: - DIMENSIONS ARE IN MILLIMETERS DRAWN DATE: - THIRD ANGLE PROJECTION 4 REVISION: DRAWING/PART NUMBER: A. Shah 1/15/21 APPROVED BY: SIZE: A3 A. Shah SCALE: APPROVED DATE: DO NOT SCALE DRAWING NS 1/15/21 SHEET 1 OF 1 THIS DRAWING IS SOLELY THE PROPERTY OF NEWHAVEN DISPLAY INTERNATIONAL, INC. THE INFORMATION IT CONTAINS IS NOT TO BE DISCLOSED, REPRODUCED OR COPIED IN WHOLE OR PART WITHOUT WRITTEN APPROVAL FROM NEWHAVEN DISPLAY. 7 8 F Pin Description and Wiring Diagram Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22~26 27 28 29 30 Symbol /CS1 /RES A0 R/W /WR E /RD DB0 DB1 DB2 DB3 DB4 DB5 DB6/SCL DB7/SI VDD VSS VOUT CAP3CAP1+ CAP1CAP2CAP2+ V1~V5 VR C86 PS /IRS External Connection MPU MPU MPU MPU MPU MPU MPU MPU MPU MPU MPU MPU MPU Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply MPU MPU MPU Function Description Active LOW Chip select Active LOW Reset signal Register select signal. A0=1: Data, A0=0: Command 6800 Mode: Read/Write select signal. R/W=1: Read R/W: =0: Write 8080 Mode: Active LOW Write Signal 6800 Mode: Active HIGH Enable Signal 8080 Mode: Active LOW Read Signal Parallel Interface DB0-DB7: Bi-directional 8-bit data bus Serial Interface: DB0-DB5: No connect in serial mode DB6= Serial clock (SCL) DB7= Serial data (SI) Supply Voltage for LCD and logic (+3.3V) Ground Voltage booster circuit – connect to 1uF Cap to VSS or VDD Connect to 1µF-2.2µF Cap to CAP1+ (Pin-18) Connect to 1µF-2.2µF Cap to CAP1-(Pin-19) and CAP3-(Pin17) Connect to 1µF-2.2µF Cap to CAP1+ (Pin-18) Connect to 1µF-2.2µF Cap to CAP2+ (Pin-21) Connect to 1µF-2.2µF Cap to CAP2- (Pin-20) 0.1µF-1µF cap to VDD or VSS No Connect Select MPU interface pin. C86 = H: 6800; C86 = L: 8080 Parallel/Serial select. PS = H: Parallel; PS = L: Serial This terminal selects the resistors for the V5 voltage level adjustment. IRS = H : Use internal resistors Recommended LCD connector: 0.5mm pitch, 30 pin FFC. Molex p/n: 52892-3095 Backlight connector: A2001H-02P Mates with: A2001WR-2P, A2001WR-S-2P, A2001WV-2P, A2001WV-S-2P [4] Electrical Characteristics Item Operating Temperature Range Storage Temperature Range Supply Voltage Supply Current Supply for LCD (contrast) “H” Level input “L” Level input “H” Level output “L” Level output Backlight supply current Backlight supply voltage Symbol TOP TST VDD IDD VLCD VIH VIL VOH VOL Condition Absolute Max Absolute Max VDD = 3.3V TOP = 25°C - Min. -20 -30 3.0 100 9.2 0.8 * VDD VSS 0.8 * VDD VSS Typ. 3.3 200 9.5 - Max. +70 +80 3.6 400 9.8 VDD 0.2 * VDD VDD 0.2 * VDD Unit ⁰C ⁰C V µA V V V V V ILED VLED ILED = 60 mA 3.0 60 3.2 75 3.4 mA V *The LED of the backlight is driven by current drain; drive voltage is for reference only. Drive voltage must be selected to ensure backlight current drain is below MAX level stated. Optical Characteristics Optimal Viewing Angles Item Top Bottom Left Right Contrast Ratio Response Time Rise Fall Symbol ϕY+ ϕYθXθX+ CR TR TF Condition CR ≥ 2 TOP = 25°C Min. 2 - Typ. 20 40 40 40 4 60 100 Max. 120 180 Controller Information Built-in ST7565R Controller. Please download specification at http://www.newhavendisplay.com/app_notes/ST7565R.pdf [5] Unit ⁰ ⁰ ⁰ ⁰ ms ms Table of Commands [6] Timing Characteristics [7] [8] [9] Example Initialization Program /*****************************************************/ Sub Command Reset P3.7 Reset P3.4 Reset P3.1 P1 = A Set P3.1 Set P3.7 End Sub /*****************************************************/ Sub Write Reset P3.7 Set P3.4 Reset P3.1 P1 = A Set P3.1 Set P3.7 End Sub /*****************************************************/ Sub Init A = &HA0 Call Command A = &HAE Call Command A = &HC0 Call Command A = &HA2 Call Command A = &H2F Call Command A = &H26 Call Command A = &H81 Call Command A = &H2F Call Command End Sub /*****************************************************/ [10] Quality Information Test Item Content of Test High Temperature storage Endurance test applying the high storage temperature for a long time. Endurance test applying the low storage temperature for a long time. Endurance test applying the electric stress (voltage & current) and the high thermal stress for a long time. Endurance test applying the electric stress (voltage & current) and the low thermal stress for a long time. Endurance test applying the electric stress (voltage & current) and the high thermal with high humidity stress for a long time. Endurance test applying the electric stress (voltage & current) during a cycle of low and high thermal stress. Endurance test applying vibration to simulate transportation and use. Low Temperature storage High Temperature Operation Low Temperature Operation High Temperature / Humidity Operation Thermal Shock resistance Vibration test Static electricity test Test Condition Endurance test applying electric static discharge. 2 -30⁰C, 240hrs 1,2 +70⁰C, 240hrs 2 -20⁰C, 240hrs 1,2 +40⁰C, 90% RH, 240hrs 1,2 -0⁰C,30min -> 25⁰C,5min -> 50⁰C,30min = 1 cycle 10 cycles 10-55Hz, 1.5mm amplitude. 60 sec in each of 3 directions X, Y, Z For 10 Minutes VS=800V, RS=1.5kΩ, CS=100pF One time Note 1: No condensation to be observed. Note 2: Conducted after 4 hours of storage at 25⁰C, 0%RH. Note 3: Test performed on product itself, not inside a container. Precautions for using LCDs/LCMs See Precautions at www.newhavendisplay.com/specs/precautions.pdf Warranty Information and Terms & Conditions http://www.newhavendisplay.com/index.php?main_page=terms [11] Note +80⁰C, 240hrs 3