NHD-C160100DIZ-FSW-FBW

NHD-C160100DiZ-FSW-FBW COG (Chip-On-Glass) Liquid Crystal Display Module NHDC160100DiZFSWFBW- Newhaven Display 160 x 100 Pixels Model (I²C) Transflective Side White LED Backlight FSTN, Positive 6:00 Optimal View Wide Temp RoHS Compliant Newhaven Display International, Inc. 2661 Galvin Ct. Elgin IL, 60124 Ph: 847-844-8795 Fax: 847-844-8796 www.newhavendisplay.com nhtech@newhavendisplay.com nhsales@newhavendisplay.com Document Revision History Revision 0 1 2 3 4 5 Date 1/06/2008 9/18/2009 10/14/2009 11/9/2009 11/17/2009 11/20/2009 6 7 8 9 10 11 12/14/2010 8/25/16 3/24/17 5/25/17 5/10/18 9/11/19 Description Initial Release User guide reformat Updated Electrical Characteristic Slave Address Updated Slave Address Updated Updated backlight supply current max / Updated Table of Commands Updated backlight cable length Mechanical Drawing, Electrical & Optical Char. Updated Mechanical Drawing Updated Electrical Characteristics Updated Module Redesign Backlight Characteristics and Supply Current Updated Functions and Features • • • • • 160 x 100 pixels Built-in ST7528i (I2C) controller +3.0V power supply 1/100 duty cycle; 1/11 bias RoHS Compliant [2] Changed by BE MC BE MC MC CL SB SB TM SB SB 1 2 3 4 5 6 SYMBOL 7 8 REVISION DATE A A LCD MODULE 160*100 B B NHD-C160100DiZ-FSW-FBW_Rev1B NEWHAVEN DISPLAY C C D D E E F Notes: 1. Driver: 2. Display Mode: 3. Op�mal View: 4. Voltage: 5. Backlight: 6. Driver IC: 1 black tape(T=0.05) 1/100 Duty, 1/11 Bias FSTN Posi�ve / Transflec�ve 6:00 3.0V VDD, 11.5V VLCD White LED ST7528I - IIC Interface 2 3 STANDARD TOLERANCE: (UNLESS OTHERWISE SPECIFIED) LINEAR: ±0.3mm 5 6 1B NHD-C160100DiZ-FSW-FBW UNLESS OTHERWISE SPECIFIED: DRAWN BY: - DIMENSIONS ARE IN MILLIMETERS DRAWN DATE: - THIRD ANGLE PROJECTION 4 REVISION: DRAWING/PART NUMBER: S. Baxi 9/11/19 APPROVED BY: SIZE: A3 S. Baxi SCALE: APPROVED DATE: DO NOT SCALE DRAWING NS 9/11/19 SHEET 1 OF 1 THIS DRAWING IS SOLELY THE PROPERTY OF NEWHAVEN DISPLAY INTERNATIONAL, INC. THE INFORMATION IT CONTAINS IS NOT TO BE DISCLOSED, REPRODUCED OR COPIED IN WHOLE OR PART WITHOUT WRITTEN APPROVAL FROM NEWHAVEN DISPLAY. 7 8 F Pin Description and Wiring Diagram Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Symbol CSB RST NC SCL SDA VDD VSS VOUT V4 V3 V2 V1 NC NC External Connection MPU MPU MPU MPU Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply Power Supply - Function Description Active Low Chip Select Active Low Reset signal No Connect Serial Clock input (requires pull-up) Serial Data input (requires pull-up) Supply Voltage for LCD and logic (+3.0V) Ground Connect to 1uF cap to VSS or VDD 1.0uF-2.2uF cap to VSS 1.0uF-2.2uF cap to VSS 1.0uF-2.2uF cap to VSS 1.0uF-2.2uF cap to VSS No Connect No Connect Recommended LCD connector: 0.5mm pitch pins. Molex p/n: 52892-1495 Backlight connector: SHR-02V-S-B Mates with: SM02B-SRSS-TB [4] Electrical Characteristics Item Operating Temperature Range Storage Temperature Range Supply Voltage Supply Current Supply for LCD (contrast) “H” Level input “L” Level input “H” Level output “L” Level output Backlight Supply Voltage Backlight Supply current Optical Characteristics Optimal Viewing Angles Contrast Ratio Item Top Bottom Left Right Response Time Rise Fall Symbol TOP TST VDD IDD VLCD VIH VIL VOH VOL Condition Absolute Max Absolute Max VDD=3.0V TOP=25℃ - Min. -20 -40 2.4 0.32 11.2 2.2 VSS 2.4 VSS Typ. 3.0 0.75 11.5 - Max. +70 +80 3.3 1.5 11.8 VDD 0.6 VDD 0.4 Unit ⁰C ⁰C V mA V V V V V VLED ILED VLED = 3.0V 2.8 30 3.0 50 3.2 70 V mA Symbol ϕY+ ϕYθXθX+ CR TR TF Condition Min. 2 - Typ. 15 40 30 30 10 50 300 Max. 200 350 Unit ⁰ ⁰ ⁰ ⁰ ms ms CR ≥ 2 TOP = 25°C Controller Information Built-in ST7528 Controller. Please download specification at http://www.newhavendisplay.com/app_notes/ST7528.pdf [5] I²C Interface: I2C interface requires 2 lines, Serial Data and Serial Clock. Both lines must be connected to the positive supply via a pull-up resistor. Data transfer may be initiated only when the bus is not busy. Bit transfer: One data bit is transferred during each clock pulse. The data on the SDA line must remain stable during the HIGH period of the clock pulse, changes in the data line at this time will be interpreted as a control signal. Start and Stop conditions: Both data and clock lines remain HIGH when the bus is not busy. A HIGH-to-LOW transition of the data line while the clock is HIGH is define as the START condition. A LOW-to-HIGH transition of the data line while the clock is HIGH is defined as the STOP condition. Acknowledge: Each byte of eight bits is followed by an acknowledge bit. The ACK bit is a HIGH signal put on the bus by the transmitter, during which time the master generates an extra ACK related clock pulse. The LCD generates an ACK after the reception of each byte. The LCD will pull-down the SDA line during the ACK clock pulse, so that the SDA line is stable LOW during the HIGH period of the ACK clock pulse. Slave Address = 0x3F Timing Characteristics Write Mode [6] [7] Table of Commands [8] [9] [10] Example Initialization Program Slave Address = 0x3F /*****************************************************/ const char Slave = 0x7E; address+Write bit const char Comsend = 0x00; const char Datasend = 0x40; /*****************************************************/ void I2C_out(unsigned char j) //I2C Output { int n; unsigned char d; d=j; for(n=0;n