NIPCI-6703

Software-Timed Analog Output – 16-Bit, 16 or 32 Channels NI 670x • 16 voltage and 16 current outputs • 16-bit resolution • 8 (5 V TTL/CMOS) lines • User-defined power-up states • Measurement services that simplify configuration and measurements Operating Systems • Windows 2000/NT/XP Recommended Software • LabVIEW • LabWindows/CVI • Measurement Studio Other Compatible Software • Visual Studio .NET • Visual Basic, C/C++, and C# Measurement Services Software (included) • NI-DAQmx driver • Measurement & Automation Explorer configuration utility Calibration Certificate Available Product NI 6703 NI 6704 1The Bus PCI PCI PXI Analog Outputs 16 voltage 16 voltage 16 current Resolution 16 bits 16 bits Output Rate Static Static Output Range ± 10 V ±10 V, 0 to 20 mA1 Digital I/O 8 8 Counter/Timers – – Current Sinks – 3 Triggers – – current output varies when set between 0 and 100 µA. Table 1. Channel, Speed, and Resolution Specifications Overview NI 670x devices are software-timed voltage and current output devices for PCI and PXI. With NI 6704 devices, you get 16 voltage outputs and 16 current outputs that you can use at the same time independently, as well as eight digital I/O (DIO) lines. You can independently set each output from ±10 V or 0 to 20 mA. The NI 6703 delivers 16 voltage outputs in addition to eight DIO lines. Current Output Channels (NI 6704 only) All 16 current outputs are identical. You can set each channel to source current from 0 to 20 mA – it does not sink current. The channels source current without requiring an external excitation source. Each output is accurate to ±2 µA. I/O Connector The analog outputs are available at a 68-pin SCSI II shielded connector. VCH are the voltage output channels. ICH are the current output channels. Each channel is referenced to a ground line, AO GND, which is shared between a voltage and current channel. A fused 5 VDC power signal from the PCI or PXI bus is available at the I/O connector as well. Hardware Voltage Output Channels All 16 voltage outputs on the NI 6703 and NI 6704 are identical. You can set each channel for a bipolar voltage output of ±10 V. Each output is accurate to ±1 mV. Software-Timed Analog Output – 16-Bit, 16 or 32 Channels Control Address Data Bus Interface Logic Main Voltage Circuit Control/Lines nvRAM/ DAC Control RAM Addr/Ctrl Digital I/O Serial Number EEPROM 16-Bit DAC RAM Data DAC Out Main Current Circuit Current Output CircuitX16 16 Voltage Output Circuit X16 16 Ordering Information PCI I/O Connector PCI/PXI/CompactPCI Bus NI PCI-6704 ..................................................................777306-01 NI PCI-6703 ..................................................................778316-01 PXI nvSRAM DIO Lines 6704 Only NI PXI-6704 ..................................................................777796-01 Includes data acquisition driver software. BUY NOW! +5 V .75 A Self-Resetting Circuit Breaker Temperature Sensor For complete product specifications, pricing, and accessory information, call (800) 813 3693 (U.S. only) or go to ni.com/dataacquisition. Figure 1. NI 670x Hardware Block Diagram Specifications Analog Output Output Characteristics Device NI 6703 NI 6704 Voltage 16 16 Channels Current 0 16 Total 16 32 Digital I/O Digital logic levels Level Input low voltage Input high voltage Output low voltage (Iout = 16 mA) Output high voltage (Iout = 16 mA) Minimum 0V 2V – 2.4 V Maximum 0.8 V 5V 0.45 V – Resolution......................................................... 16 bits, 1 in 65,536 Type of DAC...................................................... Enhanced R-2R Data transfers .................................................. Programmed I/O Voltage Output Ranges.............................................................. ±10.1 V Output coupling ................................................ DC Power-on state ................................................. Independent, user-defined Number of channels......................................... 8 input/output Compatibility .................................................... 5 V TTL/CMOS Power-on state ................................................. Input (high impedance) Bus Interface PCI, PXI ............................................................. Slave Current Output (NI 6704 Only) Range................................................................ Type .................................................................. Output compliance ........................................... Power-on state ................................................. 0.0; 0.1 to 20.2 mA Source, does not require external excitation source 0 to 10 V Independent, user-defined Physical Dimensions (not including connectors) PCI.............................................................. 17.5 by 10.7 cm (6.9 by 4.2 in.) PXI.............................................................. 16.0 by 10.0 cm (6.3 by 3.9 in.) I/O connector.................................................... 68-pin male SCSI II type For more detailed specifications, please refer to the product manual. 2 National Instruments • Tel: (800) 813 3693 • info@ni.com • ni.com Software-Timed Analog Output Cables and Accessories Analog Output Accessory Selection Guide Model NI 6703, NI 6704 Shielding Shielded Unshielded Connect to… Screw terminals Custom Screw terminals Cable SH68-68-D1 SH68-68-D1 R6868 Accessory SCB-68 CA-1000 CB-68LP Table 2. Recommended Accessories I/O Connector Blocks SCB-68 – Shielded I/O connector blocks giving you rugged, very low-noise signal termination. The SCB-68 also houses silk-screened component locations for easy addition of simple signal conditioning circuitry for your AO channels. SCB-68 ..................................................................................776844-01 Dimensions – 19.5 by 15.2 by 4.5 cm (7.7 by 6.0 by 1.8 in.) CB-68LP, CB-68LPR – 68 screw terminals for easy connection of field signals to AO devices. They include one 68-pin male connector for direct connection to 68-pin cables. The connector blocks include standoffs for use on a desktop or for mounting in a custom panel. The CB-68LP has a vertical mounted 68-pin connector. The CB-68LPR has a right-angle mounted connector and can also be used with the CA-1000. CB-68LP ................................................................................777145-01 Dimensions – 14.35 by 10.74 cm (5.65 by 4.23 in.) CB-68LPR..............................................................................777145-02 Dimensions – 7.62 by 16.19 cm (3.00 by 6.36 in.) Shielded I/O Cables SH68-68-D1 – Similar to the SH68-68-EP cable, but dedicated for use with NI 670x devices. 1 m ........................................................................................183432-01 2 m ........................................................................................183432-02 Ribbon I/O Cables R6868 – 68-conductor flat ribbon cable terminated with two 68-pin connectors. Use this cable to connect the NI 670x, NI PCI-671x, NI PXI-671x, and NI 673x devices to low-cost 68-pin accessories. 1 m ........................................................................................182482-01 SCB-68 CA-1000 CB-68LP I/O and CB-68LPR R6868 Ribbon Cable National Instruments • Tel: (800) 813 3693 • info@ni.com • ni.com 3 NI Services and Support NI has the services and support to meet your needs around the globe and through the application life cycle – from planning and development through deployment and ongoing maintenance. We offer services and service levels to meet customer requirements in research, design, validation, and manufacturing. Visit ni.com/services. Local Sales and Technical Support In offices worldwide, our staff is local to the country, giving you access to engineers who speak your language. NI delivers industryleading technical support through online knowledge bases, our applications engineers, and access to 14,000 measurement and automation professionals within NI Developer Exchange forums. Find immediate answers to your questions at ni.com/support. We also offer service programs that provide automatic upgrades to your application development environment and higher levels of technical support. Visit ni.com/ssp. SERVICE NEEDS Training and Certification NI training is the fastest, most certain route to productivity with our products. NI training can shorten your learning curve, save development time, and reduce maintenance costs over the application life cycle. We schedule instructor-led courses in cities worldwide, or we can hold a course at your facility. We also offer a professional certification program that identifies individuals who have high levels of skill and knowledge on using NI products. Visit ni.com/training. Hardware Services NI Factory Installation Services NI Factory Installation Services (FIS) is the fastest and easiest way to use your PXI or PXI/SCXI combination systems right out of the box. Trained NI technicians install the software and hardware and configure the system to your specifications. NI extends the standard warranty by one year on hardware components (controllers, chassis, modules) purchased with FIS. To use FIS, simply configure your system online with ni.com/pxiadvisor. Professional Services Our Professional Services Team is comprised of NI applications engineers, NI Consulting Services, and a worldwide National Instruments Alliance Partner program of more than 600 independent consultants and integrators. Services range from start-up assistance to turnkey system integration. Visit ni.com/alliance. Calibration Services NI recognizes the need to maintain properly calibrated devices for high-accuracy measurements. We provide manual calibration procedures, services to recalibrate your products, and automated calibration software specifically designed for use by metrology laboratories. Visit ni.com/calibration. Repair and Extended Warranty OEM Support We offer design-in consulting and product integration assistance if you want to use our products for OEM applications. For information about special pricing and services for OEM customers, visit ni.com/oem. NI provides complete repair services for our products. Express repair and advance replacement services are also available. We offer extended warranties to help you meet project life-cycle requirements. Visit ni.com/services. ni.com • (800) 813 3693 National Instruments • info@ni.com © 2005 National Instruments Corporation. All rights reserved. CVI, LabVIEW, Measurement Studio, National Instruments, National Instruments Alliance Partner, NI, ni.com, NI-DAQ, and SCXI are trademarks of National Instruments. Other product and company names listed are trademarks or trade names of their respective companies. A National Instruments Alliance Partner is a business entity independent from NI and has no agency, partnership, or joint-venture relationship with NI. 2005_5224_301_101_D_670x