NIPXI-7854R

R Series Intelligent DAQ – Data Acquisition and Control with Onboard Processing NI 781xR, NI 783xR, NI PXI-784xR, NI PXI-785xR NEW! • Onboard FPGA chip, programmable with the LabVIEW FPGA Module • User-defined triggering, timing, and decision making in hardware with 25 ns resolution • Up to 8 analog inputs, independent sampling rates up to 750 kHz, 16-bit resolution • Up to 8 analog outputs, independent update rates up to 1 MHz, 16-bit resolution • Up to 160 digital lines configurable as inputs, outputs, counters, or custom logic at rates up to 40 MHz • Direct memory access (DMA) channels for high-speed data streaming • Implement custom control logic, inline signal processing, and digital communication protocols Operating Systems • Windows XP/2000 • LabVIEW Real-Time Recommended Software • LabVIEW • LabVIEW FPGA Module • LabVIEW code compiler for FPGAs • Emulated debugging mode • LabVIEW Real-Time Module Driver Software (included) • NI-RIO Calibration Certificate Available Product Multifunction R Series NI 7851R NI 7852R NI 7853R NI 7854R NI 7841R NI 7842R NI 7830R NI 7831R NI 7833R Digital R Series NI 7811R NI 7813R Bus/Form Factor PXI PXI PXI PXI PXI PXI PCI, PXI PCI, PXI PCI, PXI PCI, PXI PCI, PXI FPGA Virtex-5 LX30 Virtex-5 LX50 Virtex-5 LX85 Virtex-5 LX110 Virtex-5 LX30 Virtex-5 LX50 Virtex-II 1M gates Virtex-II 1M gates Virtex-II 3M gates Virtex-II 1M gates Virtex-II 3M gates Analog Inputs (16-Bit) 8 8 8 8 8 8 4 8 8 – – Max Sampling Rate per Channel (kS/s) 750 750 750 750 200 200 200 200 200 – – Analog Outputs (16-Bit) 8 8 8 8 8 8 4 8 8 – – Max Update Rate per Channel (MS/s) 1 1 1 1 1 1 1 1 1 – – Digital I/O 96 96 96 96 96 96 56 96 96 160 160 Table 1. R Series Selection Guide Overview Intelligent DAQ is multifunction data acquisition that features userdefined onboard processing as well as complete flexibility of I/O timing and triggering. You can configure all device functionality by creating NI LabVIEW block diagrams with the LabVIEW FPGA Module. Your block diagram executes in hardware, giving you direct, immediate control of all I/O signals on the PXI or PCI device. With R Series and LabVIEW FPGA, you can configure user-defined hardware for a wide variety of applications requiring precise timing and control such as: • Data acquisition with flexible triggering and onboard processing • High-speed analog and discrete control loops • Pulse-width modulation (PWM) and encoder interfacing • User-defined digital communication protocols • Custom counters with up to 64-bit resolution • Hardware-timed decision making at 40 MHz Key Features Through programming in LabVIEW FPGA, you can control each of the I/O signal lines independently or synchronize a line with other channels. You can configure the digital I/O lines as custom counter/timers, PWM channels, or communication buses for user-defined protocols. All multifunction R Series devices have dedicated analog-to-digital converters/digital-to-analog converters on every analog I/O channel. This offers specialized functionality such as multirate sampling and individual channel triggering, which are beyond the capabilities of typical data acquisition hardware. You can sample every analog input channel on an R Series device simultaneously at rates up to 750 kHz, and you can program every analog output on an R Series device to update simultaneously at rates up to 1 MHz. You can also store your compiled LabVIEW FPGA application in the onboard flash memory of any R Series device and configure it for automatic loading and/or execution at power up. R Series Intelligent DAQ – Data Acquisition and Control with Onboard Processing New Virtex-5 FPGAs The new NI PXI-784xR and PXI-785xR modules use new Virtex-5 field-programmable gate arrays (FPGAs) with improved optimization capabilities that provide faster code execution and increased code capacity. These Virtex-5 FPGAs feature a new six-input lookup table (LUT) architecture for substantially improved resource utilization as well as DSP48 slices that make it possible for you to implement more complex digital signal processing at faster rates. Previous-generation Virtex-II FPGAs use four-input LUTs for up to 16 combinations of digital logic values. The new Virtex-5 FPGAs use six-input LUTs for up to 64 combinations, increasing the amount of logic that you can implement per slice. In addition, the slices themselves are placed in closer proximity to each other to reduce the propagation delay of electrons and increase overall execution rates. The single-cycle timed loop structure in LabVIEW FPGA takes full advantage of six-input LUTs for substantially improved resource utilization. This means you can optimize more LabVIEW FPGA code to fit within Virtex-5 FPGAs and perform more operations per clock cycle. Figure 1. General logic benchmarks show that Virtex-5 FPGAs offer larger sizes when compared to Virtex-II FPGAs. Figure 2. Execution speed benchmarks show that Virtex-5 FPGAs feature faster processing capabilities when compared to Virtex-II FPGAs. For more information on LabVIEW FPGA benchmarks for Virtex-5 FPGAs, visit ni.com/info and enter lvfpgabenchmarks. BUY ONLINE a t ni.com o r CALL 800 813 3693 (U.S.) 2 R Series Intelligent DAQ – Data Acquisition and Control with Onboard Processing Required Software for R Series Intelligent DAQ • NI 781xR and 783xR devices require the LabVIEW FPGA Module 7.1 or later and NI-RIO 1.3 or later driver software. • NI 784xR and 785xR devices require the LabVIEW FPGA Module 8.5.1 or later and NI-RIO 2.4 or later. • NI 7853R and 7854R devices require the LabVIEW FPGA Module 8.6 or later and NI-RIO 3.0 or later. Recommended Accessories High Performance SHC68-68-RMIO – High-performance shielded 68-conductor cable terminated with a VHDCI 68-pin male connector at one end and a 68-pin female 0.050 D-type connector at the other end that has been specifically designed for the multifunction I/O connector on R Series intelligent DAQ devices. 1 m .....................................................................189588-01 2 m .....................................................................189588-02 SHC68-68-RDIO – High-performance shielded 68-conductor cable terminated with a VHDCI 68-pin male connector at one end and a 68-pin female 0.050 D-type connector at the other end that has been specifically designed for the digital I/O connector on R Series intelligent DAQ devices. 1 m .....................................................................191667-01 SCB-68 – Shielded I/O connector block for rugged, very low-noise signal termination for connecting to 68-pin devices. The SCB-68 also includes two general-purpose breadboard areas. Dimensions – 19.5 by 15.2 by 4.5 cm (7.7 by 6.0 by 1.8 in.) SCB-68 .................................................................776844-01 Low-Cost Signal Conditioning and Channel Expansion The NI cRIO-9151 R Series expansion chassis connects directly to any digital connector on R Series devices and houses up to four C Series I/O modules for industrial signal conditioning, I/O channel expansion, and direct sensor connectivity. Ordering Information PCI NI PCI-7811R................................................................779363-01 NI PCI-7813R................................................................779370-01 NI PCI-7830R................................................................779361-01 NI PCI-7831R................................................................778797-01 NI PCI-7833R................................................................779359-01 PXI NI PXI-7811R................................................................778800-01 NI PXI-7813R................................................................779362-01 NI PXI-7830R................................................................779364-01 NI PXI-7831R................................................................778668-01 NI PXI-7833R................................................................779360-01 NI PXI-7841R................................................................780337-01 NI PXI-7842R................................................................780338-01 NI PXI-7851R................................................................780339-01 NI PXI-7852R................................................................780340-01 NI PXI-7853R................................................................780341-01 NI PXI-7854R................................................................780342-01 Includes NI-RIO driver software. Low Cost SH68-C68-S – General-purpose shielded cable that connects any type of R Series connector to 68-pin connector blocks. 0.5 m...................................................................186381-0R5 1 m .....................................................................186381-01 2 m .....................................................................186381-02 Custom Cabling SHC68-NT-S – Shielded 68-conductor cable terminated with a 68-pin male VHDCI connector at one end and unterminated bare wires at the other. Use this cable, ideal for OEM applications, to create custom cabling solutions for R Series devices. 2 m .....................................................................189041-02 NSC68-262650 – Shielded cable terminated with a VHDCI 68-pin male connector at one end and two 26-pin ribbon connectors and one 50-pin ribbon connector on the other; designed to connect the R Series RMIO connector to standard ribbon cable accessories. 1 m .....................................................................189151-01 NSC68-5050 – Shielded cable terminated with a VHDCI 68-pin male connector at one end and two 50-pin ribbon connectors on the other; designed to connect R Series RDIO connectors to standard ribbon cable accessories. 1 m .....................................................................189152-01 BUY NOW! For complete product specifications, pricing, and accessory information, call 800 813 3693 (U.S.) or go to ni.com/rseries. BUY ONLINE a t ni.com o r CALL 800 813 3693 (U.S.) 3 R Series Intelligent DAQ – Data Acquisition and Control with Onboard Processing Specifications Analog Input (NI 783xR/784xR/785xR Only) Input Characteristics Number of channels NI 7830R ......................................... 4 NI 7831R/7833R/784xR/785xR ...... 8 Input modes ........................................ DIFF, RSE, NRSE (software-selectable; selection applies to all channels) Type of ADC ........................................ Successive approximation Resolution ........................................... 16 bits, 1 in 65,536 Conversion time NI 783xR/NI 784xR ......................... 4 µs NI 785xR ......................................... 1 µs Maximum sampling rate NI 783xR/NI 784xR ......................... 200 kS/s (per channel) NI 785xR ......................................... 750 kS/s (per channel) Input impedance Powered on..................................... 10 GΩ in parallel with 100 pF Powered off/overload..................... 4.0 kΩ min Input signal range ............................... ±10 V Input bias current NI 783xR ......................................... ±2 nA NI 784xR/785xR.............................. ±5 nA Input offset current NI 783xR ......................................... ±1 nA NI 784xR/785xR.............................. ±5 nA Input coupling ..................................... DC Maximum working voltage (signal + common mode) ............ Inputs should remain within ±12 V of ground Overvoltage protection Powered on ................................ ±42 V Powered off ................................ ±35 V Data transfers ..................................... DMA, interrupts, programmed I/O Accuracy Information – NI 784xR/785xR Relative Accuracy Absolute % of Reading Accuracy Resolution (µV) Temp at Full Positive Negative Offset Single Drift Scale Single 24 Full Full Scale Hours 1 Year (µV) Point Averaged (%/°C) (±mV) Point Averaged Scale Nominal Range (V) 10.0 -10.0 0.0186 0.0228 1,591 1,029 91.6 0.0005 3.97 1,205 121 Note: Accuracies are valid for measurements following an internal calibration. Averaged numbers assume dithering and averaging of 100 single-channel readings. Measurement accuracies are listed for operational temperatures within ±1 °C of internal calibration temperature and ±10 °C of external or factory-calibration temperature. Absolute Accuracy Noise + Quantization DC Transfer Characteristics INL NI 783xR ......................................... NI 784xR/785xR.............................. DNL NI 783xR ......................................... NI 784xR/785xR.............................. No missing codes NI 783xR ......................................... NI 784xR/785xR.............................. CMRR, DC to 60 Hz............................. ±3 LSB typ, ±6 LSB max ±1 LSB typ, ±3 LSB max -1.0 to +2.0 LSB max ±0.4 LSB typ, ±0.9 LSB max 16 bits typ, 15 bits min 16 bits guaranteed -86 dB Settling Time Device NI 783xR Step Size ±20.0 V ±2.0 V ±0.2 V ±20.0 V ±2.0 V ±0.2 V 16 LSB 7.5 µs 2.7 µs 1.7 µs 2.1 µs 1.3 µs 0.8 µs Accuracy 4 LSB 10.3 µs 4.1 µs 2.9 µs 4.2 µs 1.6 µs 1.1 µs 2 LSB 40 µs 5.1 µs 3.6 µs 8 µs 1.8 µs 1.2 µs NI 784xR/ 785xR Crosstalk.............................................. -80 dB, DC to 100 kHz Dynamic Characteristics Bandwidth NI 783xR Small signal (-3 dB) .................... Large signal (1% THD) ............... NI 784xR/785xR Small signal (-3 dB) .................... Large signal (1% THD) ............... 650 kHz 55 kHz 1 MHz 500 kHz Accuracy Information – NI 783xR Relative Accuracy Absolute % of Reading Accuracy Resolution (µV) Temp at Full Positive Negative Offset Single Drift Scale Single 24 Full Full Scale Scale Hours 1 Year (µV) Point Averaged (%/°C) (±mV) Point Averaged Nominal Range (V) 10.0 -10.0 0.0496 0.0507 2,542 1779 165 0.0005 7.78 2,170 217 Note: Accuracies are valid for measurements following an internal calibration. Averaged numbers assume dithering and averaging of 100 single-channel readings. Measurement accuracies are listed for operational temperatures within ±1 °C of internal calibration temperature and ±10 °C of external or factory-calibration temperature. Absolute Accuracy Noise + Quantization Analog Output (NI 783xR/784xR/785xR Only) Output Characteristics Number of channels NI 7830R ......................................... NI 7831R/7833R/784xR/785xR ...... Output type ......................................... Resolution ........................................... Update time ........................................ Maximum update rate ........................ Type of DAC ........................................ Data transfers ..................................... 4 8 Single-ended, voltage output 16 bits, 1 in 65,536 1.0 µs 1 MS/s Enhanced R-2R DMA, interrupts, programmed I/O BUY ONLINE a t ni.com o r CALL 800 813 3693 (U.S.) 4 R Series Intelligent DAQ – Data Acquisition and Control with Onboard Processing Voltage Output Range .................................................. Output coupling................................... Output impedance NI 783xR ......................................... NI 784xR/785xR.............................. Current drive ....................................... Protection ............................................ Power-on state.................................... ±10 V DC 1.25 Ω 0.5 Ω ±2.5 mA Short-circuit to ground User configurable Protection Input NI 781xR/783xR ......................... -0.5 to 7.0 V, single line NI 784xR/785xR ......................... -20.0 to 20.0 V, single line Output ............................................. Short-circuit (up to eight lines may be shorted at a time) Minimum pulse width Input................................................ 25 ns Output ............................................. 12.5 ns Minimum sampling period.................. 5 ns Accuracy Information Nominal Range (V) Positive Negative Full Scale Full Scale 24 Hours 10.0 -10.0 0.0335 Absolute Accuracy % of Reading 1 Year 0.0351 Absolute Temp Drift Accuracy at Full Offset (µv) (%/°C) Scale (mV) 2,366 0.0005 5.88 Reconfigurable FPGA NI 7811R/7830R/7831R FPGA type............................................ Number of flip-flops............................ Number of 4-input LUTs...................... Number of 18x18 multipliers .............. Embedded block RAM......................... Virtex-II 1000 10,240 10,240 40 720 kb Virtex-II 3000 28,672 28,672 96 1,728 kb Virtex-5 LX30 19,200 19,200 32 1,152 kb Virtex-5 LX50 28,800 28,800 48 1,728 kb Virtex-5 LX85 51,840 51,840 48 3,456 kb Virtex-5 LX110 69,120 69,120 64 4,608 kb Note: Accuracies are valid for analog output following an internal calibration. Analog output accuracies are listed for operation temperatures within ±1 °C of internal calibration temperature and ±10 °C of external or factory calibration temperature. Temperature drift applies only if ambient is greater than ±10 °C of previous external calibration. DC Transfer Characteristics INL .................................................... ±0.5 LSB typ, ±4.0 LSB max DNL .................................................... ±0.5 LSB typ, ±1 LSB max Monotonicity ....................................... 16 bits, guaranteed NI 7813R/7833R FPGA type............................................ Number of flip-flops............................ Number of 4-input LUTs...................... Number of 18x18 multipliers .............. Embedded block RAM......................... Settling Time Step Size ±20.0 V ±2.0 V ±0.2 V 16 LSB 6.0 µs 2.2 µs 1.5 µs Accuracy 4 LSB 6.2 µs 2.9 µs 2.6 µs 2 LSB 7.2 µs 3.8 µs 3.6 µs NI 7841R/7851R FPGA type............................................ Number of flip-flops............................ Number of 6-input LUTs...................... Number of DSP48 slices (25x18 multipliers)................ Embedded block RAM......................... Dynamic Characteristics Slew rate............................................. 10 V/µs Noise ................................................... 150 µVrms, DC to 1 MHz Glitch energy at midscale transition..... ±200 mV for 3 µs NI 7842R/7852R FPGA type............................................ Number of flip-flops............................ Number of 6-input LUTs...................... Number of DSP48 slices (25x18 multipliers)................ Embedded block RAM......................... Digital I/O Number of channels NI 7811R/7813R ............................. NI 7830R ......................................... NI 7831R/7833R/784xR/785xR ..... Digital logic levels .............................. Level Input low voltage (VIL) Input high voltage (VIH) Output low voltage (VOL), where IOUT = -4 mA Output high voltage (VOH), where IOUT = 4 mA 160 56 96 3.3 V TTL, 5 V TTL Compatible Min (V) 0.0 V 2.0 V – 2.4 V Max (V) 0.8 V 5.5 V 0.4 V 3.3 V NI 7853R FPGA type............................................ Number of flip-flops............................ Number of 6-input LUTs...................... Number of DSP48 slices (25x18 multipliers)................ Embedded block RAM......................... Output current Source............................................. Sink ................................................. Input leakage current.......................... Power-on state.................................... Data transfers ..................................... 4.0 mA 4.0 mA ±10 µA Programmable, by line DMA, interrupts, programmed I/O NI 7854R FPGA type............................................ Number of flip-flops............................ Number of 6-input LUTs...................... Number of DSP48 slices (25x18 multipliers)................ Embedded block RAM......................... BUY ONLINE a t ni.com o r CALL 800 813 3693 (U.S.) 5 R Series Intelligent DAQ – Data Acquisition and Control with Onboard Processing Timebases Timebase reference sources NI PCI-781xR/783xR ....................... Onboard clock only NI PXI-78xxR ................................... Onboard clock, phase-locked to PXI 10 MHz clock LabVIEW FPGA derived clocks............ Up to 200 MHz Timebase accuracy, onboard clock ..... ±100 ppm, 250 ps peak-to-peak jitter Phase-locked to PXI 10 MHz clock (NI PXI-78xxR only) ......................... Adds 350 ps peak-to-peak jitter Additional frequency-dependent peak-to-peak jitter NI 781xR/783xR 40 MHz ....................................... None 80 MHz ....................................... 400 ps 120 MHz ..................................... 720 ps 160 MHz ..................................... 710 ps 200 MHz ..................................... 700 ps NI 784xR/785xR 40 MHz ....................................... None 80 MHz ....................................... 460 ps 120 MHz ..................................... 172 ps Maximum Working Voltage Maximum working voltage refers to the signal voltage plus the common-mode voltage. Channel-to-earth ................................. ±12 V, Measurement Category I Channel-to-channel............................. ±24 V, Measurement Category I Caution: Do not use the NI 783xR/784xR/785xR for connection to signals in Measurement Category II, III, or IV. Power Requirement +5 VDC (±5%)1 NI 781xR ......................................... 9 mA (typ), 50 mA (max) NI 7830R/7831R ............................. 330 mA (typ), 355 mA (max) NI 7833R ......................................... 364 mA (typ), 586 mA (max) NI 7841R/7851R ............................. 125 mA (typ), 252 mA (max) NI 7842R/7852R ............................. 136 mA (typ), 291 mA (max) NI 7853R. ........................................ 460 mA typ NI 7854R ......................................... 484 mA typ +3.3 VDC (±5%)2 NI 7811R ......................................... 650 mA (typ), 1,000 mA (max) NI 7813R ......................................... 850 mA (typ), 1,350 mA (max) NI 7830R/7831R ............................. 462 mA (typ), 660 mA (max) NI 7833R ......................................... 727 mA (typ), 1,148 mA (max) NI 7841R/7851R ............................. 525 mA (typ), 1,244 mA (max) NI 7842R/7852R ............................. 604 mA (typ), 1,484 mA (max) NI 7853R .................................................. 640 mA typ NI 7854R .................................................. 843 mA typ +12 V NI 784xR/785xR.............................. 0.5 A -12 V NI 784xR/785xR.............................. 0.25 A +5 V terminal Connector 0..................................... 0.5 A max Connector 1..................................... 0.5 A max Connector 2..................................... 0.5 A max All connectors................................. 1.5 A max3 To calculate the total current sourced by the digital outputs, use the following equation: j ∑ current sourced on channel i i=1 Power available at I/O connectors ..... 4.50 to 5.25 VDC at 1 A total, 250 mA per I/O connector pin 1 Does 2 3 Calibration (NI 783xR/784xR/785xR Only) Recommended warm-up time............. 15 minutes Calibration interval ............................. 1 year Onboard calibration reference DC level........................................... 5.000 V (±3.5 mV) (actual value stored in flash memory) Temperature coefficient...................... ±5 ppm/°C max Long-term stability.............................. ±20 ppm/1,000 h Note: Refer to Calibration Certificates at ni.com/calibration to generate a calibration certificate for the NI 783xR. Bus Interface PXI (NI PXI-78xxR only) ....................... Master, slave PCI (NI PCI-781xR/783xR only) ........... Master, slave Physical Dimensions (not including connectors) NI PCI-781xR/783xR ......................... NI PXI-78xxR ..................................... Weight NI PCI-781xR/783xR ....................... NI PXI-78xxR ................................... I/O connectors NI 781xR ......................................... 17 by 11 cm (6.7 by 4.3 in.) 16 by 10 cm (6.3 by 3.9 in.) 112 g 152 g not include current drawn from the +5 V line on the I/O connectors. Does not include current sourced by the digital outputs. The NI 784xR/785xR devices have a user-replaceable socketed fuse that opens when current exceeds the current specification. Refer to the R Series Intelligent DAQ User Manual, available at ni.com/manuals, for information about fuse replacement. Four 68-pin female high-density VHDCI type NI 783xR/784xR/785xR .................. Three 68-pin female high-density VHDCI type BUY ONLINE a t ni.com o r CALL 800 813 3693 (U.S.) 6 R Series Intelligent DAQ – Data Acquisition and Control with Onboard Processing Environmental NI 78xxR devices are intended for indoor use only. Safety and Compliance Safety NI 78xxR devices are designed to meet the requirements of the following standards of safety for electrical equipment for measurement, control, and laboratory use: • IEC 61010-1, EN 61010-1 • UL 61010-1, CSA 61010-1 Note: For UL and other safety certifications, refer to the product label or visit ni.com/certification, search by model number or product line, and click the appropriate link in the Certification column. Operating Environment NI 781xR.............................................. 0 to 55 °C (tested in accordance with IEC-60068-2-1 and IEC-60068-2-2) NI 7830R, NI 7831R 40 or 80 MHz timebase .................. 0 to 55 °C (tested in accordance with IEC-60068-2-1 and IEC-60068-2-2) NI 7833R/7841R/7842R/7851R/7852R/7853R/7854R 40 MHz timebase ........................... 0 to 55 °C (tested in accordance with IEC-60068-2-1 and IEC-60068-2-2) 80 MHz timebase ........................... 0 to 55 °C except the following: 0 to 45 °C when installed in an NI PXI-1000/B or NI PXI-101x (tested in accordance with IEC-60068-2-1 and IEC-60068-2-2) Relative humidity range...................... 10 to 90%, noncondensing (tested in accordance with IEC-60068-2-56) Altitude................................................ 2,000 m at 25 °C ambient temperature Electromagnetic Compatibility This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use: • EN 61326 (IEC 61326): Class A emissions; Basic immunity • EN 55011 (CISPR 11): Group 1, Class A emissions • AS/NZS CISPR 11: Group 1, Class A emissions • FCC 47 CFR Part 15B: Class A emissions • ICES-001: Class A emissions CE Compliance This product meets the essential requirements of applicable European Directives, as amended for CE marking, as follows: • 2006/95/EC; Low-Voltage Directive (safety) • 2004/108/EC; Electromagnetic Compatibility Directive (EMC) Note: Refer to the Declaration of Conformity (DoC) for this product for any additional regulatory compliance information. To obtain the DoC for this product, visit ni.com/certification, search by model number or product line, and click the appropriate link in the Certification column. Storage Environment Ambient temperature range ............... -20 to 70 °C (tested in accordance with IEC-60068-2-1 and IEC-60068-2-2) Relative humidity range...................... 5 to 95%, noncondensing (tested in accordance with IEC-60068-2-56) Note: Clean the device with a soft, nonmetallic brush. Make sure that the device is completely dry and free from contaminants before returning it to service. Environmental Management National Instruments is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial not only to the environment but also to NI customers. For additional environmental information, refer to the NI and the Environment Web page at ni.com/environment. This page contains the environmental regulations and directives with which NI complies, as well as other environmental information not included in this document. Shock and Vibration (for NI PXI-78xxR Only) Operational shock ............................... 30 g peak, half-sine, 11 ms pulse (tested in accordance with IEC-60068-2-27; test profile developed in accordance with MIL-PRF-28800F) Random vibration Operating ........................................ 5 to 500 Hz, 0.3 grms Nonoperating.................................. 5 to 500 Hz, 2.4 grms (tested in accordance with IEC-60068-2-64; nonoperating test profile exceeds the requirements of MIL-PRF-28800F, Class 3) Waste Electrical and Electronic Equipment (WEEE) EU Customers: At the end of their life cycle, all products must be sent to a WEEE recycling center. For more information about WEEE recycling centers and National Instruments WEEE initiatives, visit ni.com/environment/weee.htm. BUY ONLINE a t ni.com o r CALL 800 813 3693 (U.S.) 7 NI Services and Support IN TA PL SERVICE NEEDS LO Y V DE NI has the services and support to meet your needs around the globe and through the application life cycle – from planning and development through deployment and ongoing maintenance. We offer services and service levels to meet customer requirements in research, design, validation, and manufacturing. Visit ni.com/services. Local Sales and Technical Support In offices worldwide, our staff is local to the country, giving you access to engineers who speak your language. NI delivers industry-leading technical support through online knowledge bases, our applications engineers, and access to 14,000 measurement and automation professionals within NI Developer Exchange forums. Find immediate answers to your questions at ni.com/support. We also offer service programs that provide automatic upgrades to your application development environment and higher levels of technical support. Visit ni.com/ssp. MA IN Training and Certification NI training is the fastest, most certain route to productivity with our products. NI training can shorten your learning curve, save development time, and reduce maintenance costs over the application life cycle. We schedule instructor-led courses in cities worldwide, or we can hold a course at your facility. We also offer a professional certification program that identifies individuals who have high levels of skill and knowledge on using NI products. Visit ni.com/training. EL OP AN Professional Services Our NI Professional Services team is composed of NI applications and systems engineers and a worldwide National Instruments Alliance Partner program of more than 600 independent consultants and integrators. Services range from start-up assistance to turnkey system integration. Visit ni.com/alliance. OEM Support We offer design-in consulting and product integration assistance if you want to use our products for OEM applications. For information about special pricing and services for OEM customers, visit ni.com/oem. P DE Hardware Services NI Factory Installation Services NI Factory Installation Services (FIS) is the fastest and easiest way to use your PXI or PXI/SCXI combination systems right out of the box. Trained NI technicians install the software and hardware and configure the system to your specifications. NI extends the standard warranty by one year on hardware components (controllers, chassis, modules) purchased with FIS. To use FIS, simply configure your system online with ni.com/pxiadvisor. Calibration Services NI recognizes the need to maintain properly calibrated devices for high-accuracy measurements. We provide manual calibration procedures, services to recalibrate your products, and automated calibration software specifically designed for use by metrology laboratories. Visit ni.com/calibration. Repair and Extended Warranty NI provides complete repair services for our products. Express repair and advance replacement services are also available. We offer extended warranties to help you meet project life-cycle requirements. Visit ni.com/services. ni.com • 800 813 3693 National Instruments • info@ni.com *351588B-01* 351588B-01 2008-10077-301-101-D ©2008 National Instruments. All rights reserved. LabVIEW, National Instruments, National Instruments Alliance Partner, NI, ni.com, and SCXI are trademarks of National Instruments. Other product and company names listed are trademarks or trade names of their respective companies. A National Instruments Alliance Partner is a business entity independent from National Instruments and has no agency, partnership, or joint-venture relationship with National Instruments.