NMC0402X5R104K16TRPF

Multilayer Ceramic Chip Capacitors FEATURES • CLASS II DIELECTRIC, TEMPERATURE STABLE • EXCELLENT FREQUENCY CHARACTERISTICS, NON-LINEAR CAPACITANCE CHANGE • NICKEL BARRIER TERMINATIONS AND EXCELLENT MECHANICAL STRENGTH SPECIFICATIONS Capacitance Range Capacitance Tolerance Operating Temperature Range Temperature Characteristics Rated Voltages NMC Series X5R Expanded 01005 Case Size 100pF ~ 0.82µF (see high CV datasheet for higher capacitance values) ±10% (K), ±20% (M) -55°C ~ +85°C ±15%∆ max. over temperature range (with 0 Vdc applied) 6.3Vdc, 10Vdc, 16Vdc, 25Vdc, 35Vdc & 50Vdc (see NMC-H Series for higher voltages, NMC High Cap for higer capacitance) See Available Values Tables (1KHz @ +25°C) 10,000Megohms min. or 500Megohm/µF min. whichever is less @ +25°C Except: 01005 0.1mF/6.3V 100MW, 0.1mF/10V = 500MW 250% of Rated Voltage for 1 ~ 5 seconds, 50mA maximum current 1KHz, 1.0V ±0.2Vrms Dissipation Factor insulation Resistance Dielectric Withstanding Voltage Test Conditions (EIA-198-2E) Note: Reflow soldering allowed for all case sizes. Contact NIC for wave soldering restrictions. Typical X5R Temperature Coefficient 20% %∆°C 10% 0% -10% -20% Insulation Resistance (Ohm - Farads) -50 -40 -30 -20 -10 0 10 20 30 40 50 60 70 80 90 Insulation Resistance vs. Temperature 10,000 1,000 100 0 +20 +30 +40 +50 +60 +70 +80 Temperature °C PART NUMBER SYSTEM NMC 0805 X5R 102 K 50 TRP or TRPLP 3K F Series 1 NIC COMPONENTS CORP. RoHS Compliant Optional Reel Qty (3K=3,000pcs) Tape & Reel (Embossed Plastic Carrier) Tape & Reel (Punched carrier) Voltage (Vdc) Capacitance Tolerance Code (see chart) Capacitance Code, expressed in pF, first 2 digits are significant, 3rd digit is no. of zeros, “R” indicates decimal for under 10pF Temperature Characteristic Size Code (see chart) www.niccomp.com SPECIFICATIONS ARE SUBJECT TO CHANGE Multilayer Ceramic Chip Capacitors 01005 Case Size Available Values EIA Case Size Length (L) Width (W) Thickness max. (T) Termination Width (P) Capacitance 0201, 0402 & 0603 Case Size Available Values EIA Case Size 0201 Length (L) 0.6 ± 0.05 Width (W) 0.3 ± 0.05 Thickness max. (T) 0.33 Termination Width (P) 0.10 ~ 0.20 01005 0.4±0.02 0.2±0.02 0.22 0.1±0.03 Working Voltage (Vdc) 6.3 10 7.5% 100pF 7.5% 150pF 7.5% 220pF 7.5% 330pF 7.5% 470pF 7.5% 680pF 7.5% 1,000pF 10% 1,500pF 10% 2,200pF 10% 3,300pF 10% 4,700pF 10% 6,800pF 10% 10% 10,000pF 12.5% 10% 100,000pF Percentage shown represent dissipation factor W T P P L 100% Sn over Ni barrier (CONSULT FACTORY FOR CAPACITANCE VALUES NOT LISTED) NMC Series X5R Capacitance 0402 0603 1.0±0.05 1.6±0.15 0.5±0.05 0.8±0.15 0.6 1.0 0.2±0.1 0.12 ~ 0.51 Working Voltage (Vdc) 10 16 25 35 6.3 10 16 25 35 6.3 10 6.3 10% 7.5% 0.0012µF 10% 7.5% 0.0015µF 10% 7.5% 0.0018µF 10% 7.5% 0.0022µF 10% 7.5% 0.0027µF 10% 7.5% 0.0033µF 10% 7.5% 0.0039µF 10% 7.5% 10% 7.5% 5% 0.0047µF 10% 7.5% 10% 7.5% 5% 0.0056µF 10% 7.5% 10% 7.5% 5% 0.0068µF 10% 7.5% 10% 7.5% 5% 0.0075µF 10% 7.5% 10% 7.5% 5% 0.0082µF 10% 7.5% 10% 7.5% 5% 0.01µF 10% 10% 7.5% 5% 0.015µF 10% 10% 7.5% 5% 0.018µF 10% 10% 7.5% 5% 0.022µF 10% 10% 7.5% 5% 0.027µF 10% 10% 7.5% 5% 0.033µF 10% 10% 7.5% 5% 0.036µF 10% 10% 7.5% 5% 0.039µF 10% 10% 7.5% 5% 0.047µF 10% 10% 7.5% 5% 0.056µF 10% 10% 7.5% 5% 0.068µF 10% 10% 7.5% 5% 0.075µF 10% 10% 7.5% 5% 0.082µF 10% 10% 10% 7.5% 5% 0.1µF 10% 0.15µF 10% 0.18µF 10% 10% 7.5% 10% 0.22µF 0.27µF 10% 10% 10% 0.33µF 0.36µF 0.39µF 10% 10% 10% 0.47µF 10% 0.68µF 0.82µF Percentage shown represent dissipation factor 5% 5% 5% 10% 10% 7.5% 5% 10% 7.5% 5% 10% 10% 7.5% 5% 5% 10% 7.5% 5% 5% 10% 7.5% 5% 5% 10% 10% 10% 7.5% 5% 5% 10% 10% 10% 7.5% 5% 5% 10% 7.5% 5% See NMC High Capacitance datasheet for higher capacitance values or NMC-H High Voltage datasheet for higher voltage ratings 2 NIC COMPONENTS CORP. 50 www.niccomp.com SPECIFICATIONS ARE SUBJECT TO CHANGE 5% 5% 5% 5% 5% 5% 7.5% 7.5% Multilayer Ceramic Chip Capacitors REEL Taping Specifications REEL DIMENSIONS (mm) Reel Diameter (A) 7” (178 ± 2.0) 10” (250 ± 2.0) 13” (330 ± 2.0) B D B C 50 min. 100 ± 1.0 100 ± 1.0 13 ± 0.5 7 INCH REEL QUANTITIES* Size Tape Size Min. Qty Per Reel Max. Qty Per Reel C D T max. 8.4 +1.0/-0 (1812 case size 12.4 +2.0/-0) 21 ± 1.0 01005 8mm 0201 8mm 0402 8mm 0603 8mm 0805 8mm 1206 8mm 1210 8mm 1812 12mm 20,000 15,000 10,000 4,000 4,000 4,000 2,000 1,000 20,000 15,000 10,000 4,000 5,000 5,000 5,000 2,000 *Quantity dependent on chip thickness. Contact NIC for reel quantities on larger diameter reels. CARRIER TAPE MATERIAL T Parts with a thickness of >1mm will be taped on embossed plastic carrier. Parts with a thickness of less then 1mm will be taped on paper carrier A EMBOSSED PLASTIC CARRIER TAPE DIMENSIONS (mm) Tape Size W F 8mm 8.0 ± 0.2 3.5 ± 0.05 12mm 12 ± 0.2 5.5 ± 0.05 E P0 P2 D K max. 1.75 ± 0.10 4.0 ± 0.1 2.0 ± 0.5 1.5 +0.1-0.0 3.0 Notes: 1. Specifications are in compliance with EIA RS481-1-A “Taping of surface Mount Components for Automatic Placement” 2. Dimensions Ao (max.) equals component width dimension plus 0.5mm 3. Dimension Bo (max.) equals component length dimension plus 0.5mm T max. P 2.0 4.0 ± 0.1 4.5 8.0 ± 0.1 EMBOSSED PLASTIC CARRIER TAPE T D Po E P2 F Bo Ao P K See notes 2 & 3 regarding dimensions Ao and Bo PUNCHED CARRIER TAPE DIMENSIONS (mm) Type Ao Bo 01005 0.25 ± 0.04 0.45 ± 0.04 0201 0.37 ± 0.03 0.67 ± 0.05 0402 0.65 ± 0.05 1.15 ± 0.05 0603 1.1 ± 0.2 1.9 ± 0.2 0805 1.65 ± 0.2 2.4 ± 0.2 1206 2.0 ± 0.2 3.6 ± 0.2 W F E P1 P0 D0 4.0 ± 0.1 1.5 +0.1/-0.0 2.0 ± 0.05 8.0 ± 0.3 3.5 ± 0.05 1.75 ± 0.1 4.0 ± 0.10 PUNCHED CARRIER TAPE D Po t1 E F Bo t2 3 NIC COMPONENTS CORP. Ao W P1 Component Pitch www.niccomp.com SPECIFICATIONS ARE SUBJECT TO CHANGE T1 max. 0.27 0.45 T2 max. 0.36 0.80 1.1 1.4 Mounting Hole Angular Punch Hole W