NFSL036CT

No. STSE-CC7029A SPECIFICATIONS FOR NICHIA CHIP TYPE WARM WHITE LED MODEL : NFSL036CT NICHIA CORPORATION -0- Nichia STSE-CC7029A 1.SPECIFICATIONS (1) Absolute Maximum Ratings Item Forward Current Pulse Forward Current Allowable Reverse Current Power Dissipation Operating Temperature Storage Temperature Dice Temperature Soldering Temperature Symbol IF IFP IR PD Topr Tstg Tj Tsld Absolute Maximum Rating 350 450 85 1.33 -40 ~ +100 -40 ~ +100 150 Reflow Soldering : 260°C Hand Soldering : 350°C (Ts=25°C) Unit mA mA mA W °C °C °C for 10sec. for 3sec. IFP Conditions : Pulse Width < 10msec. and Duty < 1/10 = = (2) Initial Electrical/Optical Characteristics Item Symbol Forward Voltage VF Luminous Flux φv x Chromaticity Coordinate y Please refer to CIE 1931 chromaticity diagram. Condition IF=150[mA] IF=150[mA] IF=150[mA] IF=150[mA] Typ. (3.5) (17) 0.41 0.39 (Ts=25°C) Max. Unit 3.8 V lm - (3) Ranking Item Rank P10 Rank P9 Rank P8 Rank P7 Rank P6 Symbol Condition Min. 25.5 21.4 18.0 15.1 12.7 Luminous Flux φv IF=150[mA] (Ts=25°C) Max. Unit 30.3 25.5 lm 21.4 18.0 15.1 Luminous Flux Measurement allowance is ± 7%. Color Ranks x y x y 0.3575 0.3612 0.3545 0.3408 0.3897 0.3823 0.3610 0.3850 0.3575 0.3612 0.3988 0.4116 (IF=150mA,Ts=25°C) Rank d1 0.3780 0.3988 0.3970 0.4116 Rank d2 0.3720 0.3897 0.3714 0.3823 Rank e1 0.4162 0.4390 0.4200 0.4310 0.3897 0.3823 0.3822 0.3580 0.4255 0.4000 -1- 0.3720 0.3714 0.3667 0.3484 0.4053 0.3907 x y Nichia STSE-CC7029A x y 0.3822 0.3580 0.4255 0.4000 0.4129 0.3725 0.3897 0.3823 Rank e2 0.4053 0.4255 0.3907 0.4000 0.4519 0.4086 0.4355 0.3785 0.4129 0.3725 x y x y 0.3954 0.3642 0.4519 0.4086 0.4355 0.3785 Rank f4 0.4680 0.4970 0.4385 0.4466 Rank f6 0.4519 0.4770 0.4086 0.4137 0.4770 0.4137 0.4588 0.3838 x y x y Rank f3 0.4390 0.4680 0.4310 0.4385 Rank f5 0.4255 0.4519 0.4000 0.4086 Color Coordinates Measurement allowance is ± 0.01. Correspondence table of Color Coordinates – Luminous Flux ranks Ranking by Luminous Flux Ranking by Color Coordinates P6 P7 P8 P9 P10 d1, d2, e1, e2 f3, f4, f5, f6 Shaded ranks are available. 2.INITIAL OPTICAL/ELECTRICAL CHARACTERISTICS Please refer to figure’s page. 3.OUTLINE DIMENSIONS AND MATERIALS Please refer to figure’s page. Material as follows ; Package Encapsulating Resin Electrodes : : : Ceramics Silicone Resin (with Diffused + Phosphor) Au Plating 4.PACKAGING · The LEDs are packed in cardboard boxes after taping. Please refer to figure’s page. The label on the minimum packing unit shows ; Part Number, Lot Number, Ranking, Quantity · In order to protect the LEDs from mechanical shock, we pack them in cardboard boxes for transportation. · The LEDs may be damaged if the boxes are dropped or receive a strong impact against them, so precautions must be taken to prevent any damage. · The boxes are not water resistant and therefore must be kept away from water and moisture. · When the LEDs are transported, we recommend that you use the same packing method as Nichia. 5.LOT NUMBER The first six digits number shows lot number. The lot number is composed of the following characters; - Year ( 6 for 2006, 7 for 2007 ) - Month ( 1 for Jan., 9 for Sep., A for Oct., - Nichia's Product Number - Ranking by Color Coordinates - Ranking by Luminous Flux -2- B for Nov. ) 6.RELIABILITY (1) TEST ITEMS AND RESULTS Test Item Resistance to Soldering Heat (Reflow Soldering) Solderability (Reflow Soldering) Thermal Shock Standard Test Method JEITA ED-4701 300 301 JEITA ED-4701 300 303 JEITA ED-4701 300 307 JEITA ED-4701 100 105 JEITA ED-4701 200 203 JEITA ED-4701 200 201 JEITA ED-4701 100 103 JEITA ED-4701 200 202 Test Conditions Tsld=260°C, 10sec. (Pre treatment 30°C,70%,168hrs.) Tsld=215 ± 5°C, 3sec. (Lead Solder) -40°C ~ 100°C 1min. (10sec.) 1min. (Pre treatment 30°C,70%,168hrs.) -40°C ~ 25°C ~ 100°C ~ 25°C 30min. 5min. 30min. 5min. 25°C ~ 65°C ~ -10°C 90%RH 24hrs./1cycle Ta=100°C Ta=60°C, RH=90% Ta=-40°C Ta=25°C, IF=350mA Tested with Nichia standard circuit board. Nichia STSE-CC7029A Note 2 times Number of Damaged 0/22 1 time over 95% 100 cycles 0/22 0/50 Temperature Cycle Moisture Resistance Cyclic High Temperature Storage Temperature Humidity Storage Low Temperature Storage Steady State Operating Life Steady State Operating Life of High Temperature Steady State Operating Life of High Humidity Heat Steady State Operating Life of Low Temperature Permanence of Marking 100 cycles 10 cycles 1000 hrs. 1000 hrs. 1000 hrs. 1000 hrs. 1000 hrs. 500 hrs. 1000 hrs. 1 time 0/50 0/50 0/50 0/50 0/50 0/50 0/50 0/50 0/50 0/22 Ta=100°C, IF=140mA Tested with Nichia standard circuit board. 60°C, RH=90%, IF=250mA Tested with Nichia standard circuit board. Ta=-40°C, IF=150mA Tested with Nichia standard circuit board. JEITA ED-4701 500 501 JEITA ED-4701 400 403 JEITA ED-4701 300 304 Vibration Electrostatic Discharges Solvent : Isopropyl Alcohol Solvent Temperature : 20 ~ 25°C Dipping Time : 5 min. 100 ~ 2000 ~ 100Hz Sweep 4min. 200m/s2 3directions, 4cycles R=1.5kΩ, C=100pF Test Voltage=2kV 48min. 0/10 3 times Negative/Positive 0/22 Thermal resistance of LED with Nichia standard circuit board : Rja ≒ 90°C/W Nichia standard circuit board : FR4, t=1.6mm, Copper foil, t=0.07mm (2) CRITERIA FOR JUDGING DAMAGE Item Symbol Test Conditions Forward Voltage VF IF=150mA Initial Level Luminous Flux φv IF=150mA Initial Level 0.7 The test is performed after the board is cooled down to the room temperature. -3- Criteria for Judgement Min. Max. 1.1 Nichia STSE-CC7029A 7.CAUTIONS The LEDs are devices which are materialized by combining Blue LEDs and special phosphors. Consequently, the color of the LEDs is changed a little by an operating current. Care should be taken after due consideration when using LEDs. (1) Moisture Proof Package · When moisture is absorbed into the SMT package it may vaporize and expand during soldering. There is a possibility that this can cause exfoliation of the contacts and damage the optical characteristics of the LEDs. For this reason, the moisture proof package is used to keep moisture to a minimum in the package. · The moisture proof package is made of an aluminum moisture proof bag. A package of a moisture absorbent material (silica gel) is inserted into the aluminium moisture proof bag. The silica gel changes its color from blue to pink as it absorbs moisture. (2) Storage · Storage Conditions Before opening the package : The LEDs should be kept at 30°C or less and 90%RH or less. The LEDs should be used within a year. When storing the LEDs, moisture proof packaging with absorbent material (silica gel) is recommended. After opening the package : The LEDs should be kept at 30°C or less and 70%RH or less. The LEDs should be soldered within 168 hours (7days) after opening the package. If unused LEDs remain, they should be stored in the moisture proof packages, such as sealed containers with packages of moisture absorbent material (silica gel). It is also recommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bag again. · If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following condition. Baking treatment : more than 24 hours at 65 ± 5°C · Nichia LED electrodes are gold plated. The gold surface may be affected by environments which contain corrosive substances. Please avoid conditions which may cause the LED to corrode, tarnish or discolor. This corrosion or discoloration may cause difficulty during soldering operations. It is recommended that the User use the LEDs as soon as possible. · Please avoid rapid transitions in ambient temperature, especially in high humidity environments where condensation can occur. (3) Static Electricity · Static electricity or surge voltage damages the LEDs. It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. · All devices, equipment and machinery must be properly grounded. It is recommended that precautions be taken against surge voltage to the equipment that mounts the LEDs. · When inspecting the final products in which LEDs were assembled, it is recommended to check whether the assembled LEDs are damaged by static electricity or not. It is easy to find static-damaged LEDs by a light-on test or a VF test at a lower current (below 1mA is recommended). · Damaged LEDs will show some unusual characteristics such as the forward voltage becomes lower, or the LEDs do not light at the low current. Criteria : (VF > 2.0V at IF=0.5mA) -4- Nichia STSE-CC7029A (4) Designing the position of LED on a board. · No twist / warp / bent / or other stress shall be applied to the board after mounting LED with solder to avoid a crack of LED package. Refer to the following recommended position and direction of LED. 【No good】 Cathode mark 【Recommended Direction】 Cathode mark Appropriate LED mounting is to place perpendicularly against the stress affected side. · Depending on the position and direction of LED, the mechanical stress on the LED package can be changed. Refer to the following figure. E Perforated line A C D B Slit Stress : A > B = C > D > E · Do not split board by hand. Split with exclusive special tool. · If an aluminum circuit board is used, a large stress by thermal shock might cause a solder crack. For this reason, it is recommended an appropriate verification should be taken before use. -5- (5) Soldering Conditions · The LEDs can be soldered in place using the reflow soldering method. Nichia cannot make a guarantee on the LEDs after they have been assembled using the dip soldering method. · Recommended soldering conditions Pre-heat Pre-heat time Peak temperature Soldering time Condition Reflow Soldering Lead Solder Lead-free Solder 180 ~ 200°C 120 ~ 150°C 120 sec. Max. 120 sec. Max. 240°C Max. 260°C Max. Hand Soldering Temperature Soldering time 350°C Max. 3 sec. Max. (one time only) Nichia STSE-CC7029A 10 sec. Max. 10 sec. Max. refer to refer to Temperature - profile 1. Temperature - profile 2. (N2 reflow is recommended.) Although the recommended soldering conditions are specified in the above table, reflow or hand soldering at the lowest possible temperature is desirable for the LEDs. A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature. [Temperature-profile (Surface of circuit board)] Use the conditions shown to the under figure. 2.5 ~ 5°C / sec. Pre-heating 120 ~ 150°C 60sec.Max. Above 200°C 120sec.Max. 4.1 240°C Max. 10sec. Max. 1 ~ 5°C / sec. 1 ~ 5°C / sec. 2.5 ~ 5°C / sec. Pre-heating 180 ~ 200°C 60sec.Max. 260°C Max. 10sec. Max. Above 220°C [Recommended soldering pad design] 0.6 Use the following conditions shown in the figure. 120sec.Max. 3.5 (Unit : mm) · Occasionally there is a brightness decrease caused by the influence of heat or ambient atmosphere during air reflow. It is recommended that the User use the nitrogen reflow method. · The encapsulated material of the LEDs is silicone. Therefore the LEDs have a soft surface on the top of package. The pressure to the top surface will be influence to the reliability of the LEDs. Precautions should be taken to avoid the strong pressure on the encapsulated part. So when using the chip mounter, the picking up nozzle that does not affect the silicone resin should be used. · Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. · Reflow soldering should not be done more than two times. · When soldering, do not put stress on the LEDs during heating. (6) Cleaning · It is recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs. When using other solvents, it should be confirmed beforehand whether the solvents will dissolve the package and the resin or not. Freon solvents should not be used to clean the LEDs because of worldwide regulations. · Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition. Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur. -6- Nichia STSE-CC7029A (7) Heat Generation · Thermal design of the end product is of paramount importance. Please consider the heat generation of the LED when making the system design. The coefficient of temperature increase per input electric power is affected by the thermal resistance of the circuit board and density of LED placement on the board, as well as other components. It is necessary to avoid intense heat generation and operate within the maximum ratings given in this specification. · Please determine the operating current with consideration of the ambient temperature local to the LED and refer to the plot of Ambient temperature vs. Allowable Forward Current on CHARACTERISTICS in this specifications. Please also take measures to remove heat from the area near the LED to improve the operational characteristics of the LED. · The equation 1 indicates correlation between Tj and Ta, and the equation 2 indicates correlation between Tj and Ts. Tj=Ta + Rja W 1 Tj=Ts + Rjs W 2 Tj = Dice Temperature : °C, Ta = Ambient Temperature : °C, Ts = Solder Temperature (Cathode Side) : °C, Rja = Heat resistance from Dice to Ambient temperature : °C /W, Rjs = Heat resistance from Dice to Ts measuring point ≒ 40°C /W, W = Inputting Power (IF VF) : W (8) Others · NFSL036C complies with RoHS Directive. · The LED light output is strong enough to injure human eyes. Precautions must be taken to prevent looking directly at the LEDs with unaided eyes for more than a few seconds. · Flashing lights have been known to cause discomfort in people; you can prevent this by taking precautions during use. Also, people should be cautious when using equipment that has had LEDs incorporated into it. · The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment, communications equipment, measurement instruments and household appliances). Consult Nichia’s sales staff in advance for information on the applications in which exceptional quality and reliability are required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control systems, automobiles, traffic control equipment, life support systems and safety devices). · User shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent from Nichia. When defective LEDs are found, the User shall inform Nichia directly before disassembling or analysis. · The formal specifications must be exchanged and signed by both parties before large volume purchase begins. · The appearance and specifications of the product may be modified for improvement without notice. -7- Nichia STSE-CC7029A 0.9 520 0.8 510 0.7 530 540 ICI Chromaticity Diagram 550 560 0.6 570 500 0.5 e1 f3 f4 580 590 600 610 620 630 0.4 y d1 0.3 490 d2 e2 f5 f6 0.2 480 470 460 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.1 0 x Color Coordinates Measurement allowance is ± 0.01. -8- Forward Voltage vs. Forward Current Relative Luminous Flux (a.u.) 1000 Forward Current IFP (mA) Ta=25℃ Forward Current vs. Relative Luminous Flux 3.0 2.5 2.0 1.5 1.0 0.5 0 0 100 200 300 400 500 600 Forward Current IFP (mA) Ta=25℃ Allowable Forward Current IFP (mA) Duty Ratio vs. Allowable Forward Current Luminous Efficiency (lm/W) Luminous Flux (lm) 1000 Pulse Width < 10msec. = Ta=25℃ Forward Current vs. Luminous Efficiency 60 50 40 30 20 10 0 0 100 200 300 400 500 600 Forward Current IFP (mA) Luminous Efficiency : Luminous Flux : Ta=25℃ 150 100 50 450 350 10 2.5 3.0 3.5 4.0 4.5 5.0 Forward Voltage VF (V) 200 1 5 10 20 50 100 Duty Ratio (%) Ambient Temperature vs. Forward Voltage IFP=150mA 4.5 4.0 3.5 3.0 2.5 -60 -30 0 30 60 90 120 Ambient Temperature Ta (°C) Relative Luminous Flux (a.u.) 5.0 Forward Voltage VF (V) Ambient Temperature vs. Relative Luminous Flux 2.0 IFP=150mA 1.0 Allowable Forward Current IF (mA) Ambient Temperature vs. Allowable Forward Current 500 400 300 200 100 0 0 Rja=60°C/W Rja=75°C/W Rja=90°C/W -9- 0.5 0.2 -60 -30 0 30 60 90 120 Ambient Temperature Ta (°C) 20 40 60 80 100 120 Ambient Temperature Ta (°C) Nichia STSE-CC7029A Model NFSL036C NICHIA CORPORATION Title No. CHARACTERISTICS 070227762101 Forward Current vs. Chromaticity Coordinate Relative Emission Intensity (a.u.) Spectrum 1.2 1.0 0.8 0.6 0.4 0.2 0 350 450 550 650 750 Wavelength λ (nm) 850 Ta=25°C IFP=150mA 0.41 Ta=25°C 0.40 0.39 0.38 0.37 0.38 20mA 150mA y 350mA 0.39 0.40 0.41 0.42 x Ambient Temperature vs. Chromaticity Coordinate 0.41 Relative Illuminance (a.u.) Directivity 1.0 0° Ta=25°C IFP=150mA 10° 20° 30° 40° 50° 0.5 60° 70° 80° 0 90° 60° 30° Radiation Angle 0° 0.5 90° 1.0 IFP=150mA 0.40 0.39 0.38 0.37 0.38 85°C 100°C -40°C 0°C 25°C 50°C y -10- 0.39 0.40 0.41 0.42 x Nichia STSE-CC7029A Model NFSL036C NICHIA CORPORATION Title No. CHARACTERISTICS 070227762111 3.5 φ 2.9 0.8 3.2 0.8 3.5 3.2 Cathode mark Anode Cathode A K Protection device ITEM PACKAGE ENCAPSULATING RESIN ELECTRODES MATERIALS Ceramics Silicone Resin (with Diffused + Phosphor) Au Plating Nichia STSE-CC7029A NFSL036C has a protection device built in as a protection circuit against static electricity. Model 1 -11- NFSL036C Unit mm 8/1 Scale Allow ±0.2 NICHIA CORPORATION Title No. OUTLINE DIMENSIONS 070227762121 ±0.1 Taping PART φ1.5 +0.1 -0 Reel PART 0.2 3.85 ±0.1 ±0.05 1.75 4 ±0.1 Cathode mark 2 ±0.05 φ180 +0 -3 15.4 +1 13-0 ±1 21 φ ±0.05 8 0. ± 5.5 +0.3 12-0.1 8 ±0.1 1 φ1.5 +0.2 -0 ±0.1 XXXX LED 3.85 ±0.1 Reel End of Tape No LEDs TYPE NFSx036xT LOT XXXXXX-△■ QTY pcs LEDs mounting part No LEDs Top cover tape φ 13 Label ± 0. 2 φ60-0 +1 -12Pull direction Reel Lead Min.40mm (No LEDs) Embossed carrier tape Reel Lead Min.160mm (No LEDs is more than 40) Reel Lead Min.400mm Nichia STSE-CC7029A 2,000pcs/Reel Taping is based on the JIS C 0806 : Packaging of Electronic Components on Continuous Tapes. Model NFSx036xT Unit mm Scale Allow NICHIA CORPORATION Title No. TAPING DIMENSIONS 050620537332 Nichia STSE-CC7029A The reel and moisture absorbent material are put in the moisture proof foil bag and then heat sealed. Reel Label Seal NICHIA XXXX LED TYPE LOT QTY NFSx036xT xxxxxxPCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Moisture absorbent material Moisture proof foil bag The box is partitioned with the cardboard. Label NICHIA Nichia LED XXXX LED TYPE RANK QTY NFSx036xT PCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Packing unit Moisture proof foil bag Cardboard box Cardboard box S Cardboard box M Cardboard box L Reel/bag 1reel Quantity/bag (pcs) 2,000 MAX. Reel/box 5reel MAX. 10reel MAX. 20reel MAX. Quantity/box (pcs) 10,000 MAX. 20,000 MAX. 40,000 MAX. Dimensions (mm) 291 237 120 8t 259 247 243 5t 444 262 259 8t Model NFSx036xT NICHIA CORPORATION Title No. PACKING 050616541931 -13-