No. STSE-CC7034B
SPECIFICATIONS FOR NICHIA CHIP TYPE WHITE LED
MODEL : NHSW046HT
NICHIA CORPORATION
-0-
Nichia
STSE-CC7034B
1.SPECIFICATIONS
(1) Absolute Maximum Ratings Item Forward Current Pulse Forward Current Allowable Reverse Current Power Dissipation Operating Temperature Storage Temperature Soldering Temperature Symbol IF IFP IR PD Topr Tstg Tsld Absolute Maximum Rating 10 30 85 30 -40 ~ +100 -40 ~ +100 Reflow Soldering : 260°C Dip Soldering : 260°C Hand Soldering : 350°C
and Duty < 1/10 =
(Ta=25°C) Unit mA mA mA mW °C °C for 10sec. for 10sec. for 3sec.
IFP Conditions
:
Pulse Width < 10msec. =
(2) Initial Electrical/Optical Characteristics Item Symbol Forward Voltage VF Luminous Intensity Iv x Chromaticity Coordinate y Please refer to CIE 1931 chromaticity diagram.
Condition IF=5[mA] IF=5[mA] IF=5[mA] IF=5[mA]
Typ. (2.9) (35) 0.31 0.32
(Ta=25°C) Max. Unit 3.1 V mcd -
(3) Ranking Item Luminous Intensity Rank P Rank O Rank N Symbol Iv Iv Iv Condition IF=5[mA] IF=5[mA] IF=5[mA] Min. 45 32 23
(Ta=25°C) Max. Unit 63 mcd 45 mcd 32 mcd
Luminous Intensity Measurement allowance is ± 10%.
Color Ranks x y x y 0.280 0.248 0.296 0.276 Rank a0 0.264 0.283 0.267 0.305 Rank b2 0.287 0.330 0.295 0.339 0.296 0.276 0.330 0.318 x y x y 0.287 0.295 0.330 0.318
(IF=5mA,Ta=25°C) Rank b1 0.283 0.330 0.330 0.305 0.360 0.339 Rank c0 0.330 0.361 0.360 0.385 0.356 0.351
Color Coordinates Measurement allowance is ± 0.01. One delivery will include up to two consecutive color ranks and three luminous intensity ranks of the products. The quantity-ratio of the ranks is decided by Nichia.
2.INITIAL OPTICAL/ELECTRICAL CHARACTERISTICS
Please refer to figure’s page.
-1-
Nichia
STSE-CC7034B
3.OUTLINE DIMENSIONS AND MATERIALS
Please refer to figure’s page. Material as follows ; Package Encapsulating Resin Electrodes : : : Heat-Resistant Polymer Epoxy Resin (with Diffused + Phosphor) Ag Plating Copper Alloy
4.PACKAGING
· The LEDs are packed in cardboard boxes after taping. Please refer to figure’s page. The label on the minimum packing unit shows ; Part Number, Lot Number, Ranking, Quantity · In order to protect the LEDs from mechanical shock, we pack them in cardboard boxes for transportation. · The LEDs may be damaged if the boxes are dropped or receive a strong impact against them, so precautions must be taken to prevent any damage. · The boxes are not water resistant and therefore must be kept away from water and moisture. · When the LEDs are transported, we recommend that you use the same packing method as Nichia.
5.LOT NUMBER
The first six digits number shows lot number. The lot number is composed of the following characters; - Year ( 6 for 2006, 7 for 2007 ) - Month ( 1 for Jan., 9 for Sep., A for Oct., - Nichia's Product Number - Ranking by Color Coordinates - Ranking by Luminous Intensity
B for Nov. )
-2-
Nichia
STSE-CC7034B
6.RELIABILITY
(1) TEST ITEMS AND RESULTS
Test Item Resistance to Soldering Heat (Dip Soldering) Solderability (Dip Soldering) Resistance to Soldering Heat (Reflow Soldering) Solderability (Reflow Soldering) Thermal Shock Standard Test Method JEITA ED-4701 300 301 JEITA ED-4701 300 303 JEITA ED-4701 300 301 JEITA ED-4701 300 303 JEITA ED-4701 300 307 JEITA ED-4701 100 105 JEITA ED-4701 200 203 JEITA ED-4701 200 201 JEITA ED-4701 100 103 JEITA ED-4701 200 202 Test Conditions Tsld=260°C, 10sec. (Pre treatment 30°C,70%,168hrs.) Tsld=235 ± 5°C, 2sec. (using flux) Tsld=260°C, 10sec. (Pre treatment 30°C,70%,168hrs.) Tsld=215 ± 5°C, 3sec. (using flux, Lead Solder) -40°C ~ 100°C 1min. (10sec.) 1min. (Pre treatment 30°C,70%,168hrs.) -40°C ~ 25°C ~ 100°C ~ 25°C 30min. 5min. 30min. 5min. 25°C ~ 65°C ~ -10°C 90%RH 24hrs./1cycle Ta=100°C Ta=60°C, RH=90% Ta=-40°C Ta=25°C, IF=10mA Ta=85°C, IF=5mA 60°C, RH=90%, IF=5mA Ta=-40°C, IF=5mA JEITA ED-4701 500 501 JEITA ED-4701 400 403 Solvent : Isopropyl Alcohol Solvent Temperature : 20 ~ 25°C Dipping Time : 5 min. 100 ~ 2000 ~ 100Hz Sweep 4min. 200m/s2 3directions, 4cycles 75cm R=1.5kΩ, C=100pF Test Voltage=2kV Note 1 time Number of Damaged 0/22
1 time over 95% 2 times
0/22 0/22
1 time over 95% 100 cycles
0/22 0/100
Temperature Cycle Moisture Resistance Cyclic High Temperature Storage Temperature Humidity Storage Low Temperature Storage Steady State Operating Life Steady State Operating Life of High Temperature Steady State Operating Life of High Humidity Heat Steady State Operating Life of Low Temperature Permanence of Marking
100 cycles 10 cycles 1000 hrs. 1000 hrs. 1000 hrs. 1000 hrs. 1000 hrs. 1000 hrs. 1000 hrs. 1 time
0/100 0/100 0/100 0/100 0/100 0/100 0/100 0/100 0/100 0/22
Vibration
48min.
0/10
Drop Electrostatic Discharge JEITA ED-4701 300 304
3 times 3 times Negative/Positive
0/10 0/22
(2) CRITERIA FOR JUDGING DAMAGE
Item Forward Voltage Luminous Intensity Condition 1 Luminous Intensity Condition 2 Symbol VF IV IV Test Conditions IF=5mA IF=5mA IF=5mA Criteria for Judgement Min. Max. L.S.L.**) L.S.L.**) 0.7 0.5 U.S.L.*) 1.1
*) U.S.L. : Upper Standard Level
**) L.S.L. : Lower Standard Level -3-
These test items are judged by the criteria of Luminous Intensity Condition 2.
Nichia
STSE-CC7034B
7.CAUTIONS
The LEDs are devices which are materialized by combining Blue LEDs and special phosphors. Consequently, the color of the LEDs is changed a little by an operating current. Care should be taken after due consideration when using LEDs. (1) Moisture Proof Package · When moisture is absorbed into the SMT package it may vaporize and expand during soldering. There is a possibility that this can cause exfoliation of the contacts and damage to the optical characteristics of the LEDs. For this reason, the moisture proof package is used to keep moisture to a minimum in the package. · The moisture proof package is made of an aluminum moisture proof bag. A package of a moisture absorbent material (silica gel) is inserted into the aluminum moisture proof bag. The silica gel changes its color from blue to pink as it absorbs moisture. (2) Storage · Storage Conditions Before opening the package : The LEDs should be kept at 30°C or less and 90%RH or less. The LEDs should be used within a year. When storing the LEDs, moisture proof packaging with absorbent material (silica gel) is recommended. After opening the package : The LEDs should be kept at 30°C or less and 70%RH or less. The LEDs should be soldered within 168 hours (7days) after opening the package. If unused LEDs remain, they should be stored in moisture proof packages, such as sealed containers with packages of moisture absorbent material (silica gel). It is also recommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bag again. · If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : more than 24 hours at 65 ± 5°C · Nichia LED electrodes are silver plated copper alloy. The silver surface may be affected by environments which contain corrosive substances. Please avoid conditions which may cause the LED to corrode, tarnish or discolor. This corrosion or discoloration may cause difficulty during soldering operations. It is recommended that the User use the LEDs as soon as possible. · Please avoid rapid transitions in ambient temperature, especially in high humidity environments where condensation can occur. (3) Heat Generation · Thermal design of the end product is of paramount importance. Please consider the heat generation of the LED when making the system design. The coefficient of temperature increase per input electric power is affected by the thermal resistance of the circuit board and density of LED placement on the board, as well as other components. It is necessary to avoid intense heat generation and operate within the maximum ratings given in this specification. · The operating current should be decided after considering the ambient maximum temperature of LEDs.
-4-
Nichia
STSE-CC7034B
(4) Soldering Conditions · The LEDs can be soldered in place using the reflow soldering method and the dip soldering method. · Recommended soldering conditions
Pre-heat Pre-heat time Peak temperature Soldering time Condition Reflow Soldering Lead Solder Lead-free Solder 180 ~ 200°C 120 ~ 150°C 120 sec. Max. 120 sec. Max. 260°C Max. 240°C Max. 10 sec. Max. refer to Temperature - profile 1. 10 sec. Max. refer to Temperature - profile 2. (N2 reflow is recommended.) Dip Soldering Pre-heat Pre-heat time Solder bath temperature Dipping time 100°C Max. 60 sec. Max. 260°C Max. 10 sec. Max. Hand Soldering Temperature Soldering time 350°C Max. 3 sec. Max. (one time only)
Although the recommended soldering conditions are specified in the above table, reflow, dip or hand soldering at the lowest possible temperature is desirable for the LEDs. A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature. [Temperature-profile (Surface of circuit board)] Use the conditions shown to the under figure.
2.5 ~ 5°C / sec. Pre-heating 120 ~ 150°C 240°C Max. 10sec. Max.
60sec.Max. Above 200°C
1~ 5°C / sec. Pre-heating 180 ~ 200°C
260°C Max. 10sec. Max.
60sec.Max. Above 220°C
2.5 ~ 5°C / sec.
1~ 5°C / sec.
120sec.Max.
120sec.Max.
[Recommended soldering pad design] Use the following conditions shown in the figure.
9.2 4 0.8 0.8 4
1
4
: Solder resist
(Unit : mm)
· Occasionally there is a brightness decrease caused by the influence of heat or ambient atmosphere during air reflow. It is recommended that the User use the nitrogen reflow method. · Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. · Reflow soldering should not be done more than two times. · Dip soldering should not be done more than one time. · When soldering, do not put stress on the LEDs during heating. · After soldering, do not warp the circuit board.
-5-
Nichia STSE-CC7034B (5) Cleaning · It is recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs. When using other solvents, it should be confirmed beforehand whether the solvents will dissolve the package and the resin or not. Freon solvents should not be used to clean the LEDs because of worldwide regulations. · Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition. Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur. (6) Static Electricity · Static electricity or surge voltage damages the LEDs. It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. · All devices, equipment and machinery must be properly grounded. It is recommended that precautions be taken against surge voltage to the equipment that mounts the LEDs. · When inspecting the final products in which LEDs were assembled, it is recommended to check whether the assembled LEDs are damaged by static electricity or not. It is easy to find static-damaged LEDs by a light-on test or a VF test at a lower current (below 1mA is recommended). · Damaged LEDs will show some unusual characteristics such as the forward voltage becomes lower, or the LEDs do not light at the low current. Criteria : (VF > 2.0V at IF=0.5mA) (7) Others · NHSW046H complies with RoHS Directive. · The LED light output is strong enough to injure human eyes. Precautions must be taken to prevent looking directly at the LEDs with unaided eyes for more than a few seconds. · Flashing lights have been known to cause discomfort in people; you can prevent this by taking precautions during use. Also, people should be cautious when using equipment that has had LEDs incorporated into it. · The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment, communications equipment, measurement instruments and household appliances). Consult Nichia’s sales staff in advance for information on the applications in which exceptional quality and reliability are required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control systems, automobiles, traffic control equipment, life support systems and safety devices). · User shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent from Nichia. When defective LEDs are found, the User shall inform Nichia directly before disassembling or analysis. · The formal specifications must be exchanged and signed by both parties before large volume purchase begins. · The appearance and specifications of the product may be modified for improvement without notice.
-6-
Nichia STSE-CC7034B
ICI Chromaticity Diagram
0.9 520 530 0.8 540 510 0.7 550
560 0.6 570 500 0.5 580 590 0.4 600
y
b1
0.3 490
c0 b2
610 620 630
a0
0.2
480 0.1 470 460
0
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
x
Color Coordinates Measurement allowance is ± 0.01.
-7-
Forward Voltage vs. Forward Current
100 Forward Current IFP (mA) 50 30 10 5 Ta=25°C Relative Luminosity (a.u.)
Forward Current vs. Relative Luminosity
4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 0 10 20 30 40 Forward Current IFP (mA) Ta=25°C Allowable Forward Current IFP (mA)
Duty Ratio vs. Allowable Forward Current
100 50 30 10 5 Ta=25°C
1 2.5
2.7 2.9 3.1 3.3 3.5 Forward Voltage VF (V)
1
1
5 10 20 50 100 Duty Ratio (%)
Ambient Temperature vs. Forward Voltage
3.2 Forward Voltage VF (V) 3.1 3.0 2.9 2.8 2.7 2.6 -60 -30 0 30 60 90 120 Ambient Temperature Ta (°C) IFP=5mA Relative Luminosity (a.u.)
Ambient Temperature vs. Relative Luminosity
2.0 IFP=5mA 1.0 Allowable Forward Current IF (mA)
Ambient Temperature vs. Allowable Forward Current
15.0 12.5 10.0 7.5 5.0 2.5 0 0 20 40 60 80 100 120 Ambient Temperature Ta (°C)
-8-
0.5
0.2 -60 -30 0 30 60 90 120 Ambient Temperature Ta (°C)
Nichia STSE-CC7034B
Model
NHSW046H
NICHIA CORPORATION
Title No.
CHARACTERISTICS
070320762781
Forward Current vs. Chromaticity Coordinate
Relative Emission Intensity (a.u.)
Spectrum
1.2 1.0 0.8 0.6 0.4 0.2 0 350 450 550 650 Wavelength λ (nm) 750 Ta=25°C IF=5mA
0.34 Ta=25°C 0.33 0.32
1mA 2mA 5mA 10mA
y
0.31 0.30
30mA
0.29 0.28 0.29 0.30 0.31 0.32 0.33
x Ambient Temperature vs. Chromaticity Coordinate
0.34 IFP=5mA 0.33
-40°C
Directivity
1.0
Relative Luminosity (a.u.)
0°
Y
10° 20° 30° 40° 50°
Y X X
y
-9-
0.32 0.31 0.30
85°C 100°C
0°C 25°C 50°C
0.5 Ta=25°C IFP=5mA X-X Y-Y 0 90° 60° 30° Radiation Angle 0° 0.5
60° 70° 80° 90° 1.0
0.29 0.28 0.29 0.30 0.31 0.32 0.33
x
Nichia STSE-CC7034B
Model
NHSW046H
NICHIA CORPORATION
Title No.
CHARACTERISTICS
070320762791
1.4 (1.15) 0.4
Anode
2.2 2 (1.55)
0.4
(1.4)
Cathode mark (C 0.25)
Cathode
Internal Circuit A
(0.7) (0.7)
-10-
1.3
Protection device K
0.9
ITEM PACKAGE ENCAPSULATING RESIN ELECTRODES
MATERIALS Heat-Resistant Polymer Epoxy Resin (with Diffused + Phosphor) Ag Plating Copper Alloy
NHSW046x has a protection device built in as a protection circuit against static electricity. Nichia STSE-CC7034B
Model
NHSW046x
Unit mm 15/1 Scale Allow ±0.1
NICHIA CORPORATION
Title No.
OUTLINE DIMENSIONS
061205537022
1.75±0.1
Taping part
φ 1.5+0.1 -0 4±0.1 2±0.05
0.25±0.05
Reel part
φ 180+0 -3
11.4±1 9±0.3
3.5±0.05
8+0.3 - 0.1
2.4±0.1
φ2
(2.75)
φ 13
±0.2
Cathode mark 4±0.1
1.51±0.1 φ 1.48±0.1 1+0.2 -0
Label
XXXX LED
TYPE NHSx046xT LOT xxxxxxQTY pcs RoHS
Reel End of tape
No LEDs
LEDs mounting part
No LEDs
φ 60+1 -0
1 ±0 . 8
-11Embossed carrier tape Reel Lead Min.160mm (No LEDs)
Reel Lead Min.100mm (No LEDs)
Pull direction
Top cover tape
Reel Lead Min.400mm
Nichia STSE-CC7034B
3,000pcs/Reel Model
Taping is based on the JIS C 0806 : Packaging of Electronic Components on Continuous Tapes.
NHSx046xT
Unit mm Scale Allow
NICHIA CORPORATION
Title No.
TAPING DIMENSIONS
070606548073
Nichia STSE-CC7034B
The reel and moisture absorbent material are put in the moisture proof foil bag and then heat sealed.
Reel
Label
Seal
TYPE LOT QTY
NICHIA
XXXX LED
NHSx046xT xxxxxxPCS
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
RoHS
Moisture absorbent material
Moisture proof foil bag
The box is partitioned with the cardboard.
Label
NICHIA
Nichia
LED
XXXX LED
TYPE RANK QTY NHSx046xT PCS RoHS
NICHIA CORPORATION
491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN
Packing unit
Moisture proof foil bag Cardboard box Cardboard box S Cardboard box M Cardboard box L Reel/bag 1reel Quantity/bag (pcs) 3,000 MAX. Reel/box 7reel MAX. 15reel MAX. 30reel MAX. Quantity/box (pcs) 21,000 MAX. 45,000 MAX. 90,000 MAX.
Dimensions (mm) 291 237 120 8t 259 247 243 5t 444 262 259 8t
Model
NHSx046xT
NICHIA CORPORATION
Title No.
PACKING
070606546073
-12-