NJSE036AT

Nichia STS-DA1-0227 SPECIFICATIONS FOR NICHIA CHIP TYPE BLUISH-GREEN LED MODEL : NJSE036AT NICHIA CORPORATION -0- Nichia STS-DA1-0227 1.SPECIFICATIONS (1) Absolute Maximum Ratings Item Forward Current Pulse Forward Current Allowable Reverse Current Power Dissipation Operating Temperature Storage Temperature Dice Temperature Soldering Temperature Symbol IF IFP IR PD Topr Tstg Tj Tsld Absolute Maximum Rating 650 900 85 2.8 -30 ~ + 85 -40 ~ +100 150 Reflow Soldering : 260°C Hand Soldering : 350°C (Ts=25°C) Unit mA mA mA W °C °C °C for 10sec. for 3sec. IFP Conditions : Pulse Width ≤ 10msec. and Duty ≤ 1/10 (2) Initial Electrical/Optical Characteristics Item Symbol Forward Voltage VF Luminous Flux φv x Chromaticity Coordinate y Please refer to CIE 1931 chromaticity diagram. Condition IF=350[mA] IF=350[mA] IF=350[mA] IF=350[mA] Typ. (3.9) (30.0) 0.085 0.490 (Ts=25°C) Max. Unit 4.3 V lm - (3) Ranking Item Rank P12 Rank P11 Rank P10 Rank P9 Rank P8 Symbol Condition Min. 36.0 30.3 25.5 21.4 18.0 Luminous Flux φv IF=350[mA] (Ts=25°C) Max. Unit 42.8 36.0 lm 30.3 25.5 21.4 Luminous Flux Measurement allowance is ± 7%. Color Ranks x y x y 0.05 0.30 0.05 0.48 Rank B 0.05 0.13 0.40 0.40 Rank D 0.05 0.13 0.58 0.58 0.13 0.30 0.13 0.48 x y x y 0.04 0.39 0.06 0.55 (IF=350mA,Ts=25°C) Rank C 0.04 0.12 0.12 0.49 0.49 0.39 Rank E 0.06 0.14 0.65 0.65 0.14 0.55 Color Coordinates Measurement allowance is ± 0.012. Basically, a shipment shall consist of the LEDs of a combination of the above ranks. The percentage of each rank in the shipment shall be determined by Nichia. -1- Nichia STS-DA1-0227 Correspondence table of Color Coordinates – Luminous Flux ranks Ranking by Luminous Flux Ranking by Color Coordinates P8 P9 P10 P11 P12 B, C D, E Shaded ranks are available. 2.INITIAL OPTICAL/ELECTRICAL CHARACTERISTICS Please refer to “CHARACTERISTICS” on the following pages. 3.OUTLINE DIMENSIONS AND MATERIALS Please refer to “OUTLINE DIMENSIONS” on the following page. Material as follows ; Package : Ceramics Encapsulating Resin : Silicone Resin (with Diffused) Electrodes : Au Plating 4.PACKAGING · The LEDs are packed in cardboard boxes after taping. Please refer to “TAPING DIMENSIONS” and “PACKING” on the following pages. The label on the minimum packing unit shows ; Part Number, Lot Number, Ranking, Quantity · In order to protect the LEDs from mechanical shock, we pack them in cardboard boxes for transportation. · The LEDs may be damaged if the boxes are dropped or receive a strong impact against them, so precautions must be taken to prevent any damage. · The boxes are not water resistant and therefore must be kept away from water and moisture. · When the LEDs are transported, we recommend that you use the same packing method as Nichia. 5.LOT NUMBER The first six digits number shows lot number. The lot number is composed of the following characters; - Year ( 7 for 2007, 8 for 2008 ) - Month ( 1 for Jan., 9 for Sep., A for Oct., - Nichia's Product Number - Ranking by Color Coordinates - Ranking by Luminous Flux B for Nov. ) -2- Nichia STS-DA1-0227 6.RELIABILITY (1) TEST ITEMS AND RESULTS Test Item Resistance to Soldering Heat (Reflow Soldering) Solderability (Reflow Soldering) Thermal Shock Standard Test Method JEITA ED-4701 300 301 JEITA ED-4701 300 303 JEITA ED-4701 300 307 JEITA ED-4701 100 105 JEITA ED-4701 200 203 JEITA ED-4701 200 201 JEITA ED-4701 100 103 JEITA ED-4701 200 202 Test Conditions Tsld=260°C, 10sec. (Pre treatment 30°C,70%,168hrs.) Tsld=215 ± 5°C, 3sec. (Lead Solder) -40°C ~ 100°C 1min. (10sec.) 1min. (Pre treatment 30°C,70%,168hrs.) -40°C ~ 25°C ~ 100°C ~ 25°C 30min. 5min. 30min. 5min. 25°C ~ 65°C ~ -10°C 90%RH 24hrs./1cycle Ta=100°C Ta=60°C, RH=90% Ta=-40°C Ta=25°C, IF=650mA Tested with Nichia standard circuit board. Note 2 times Number of Damaged 0/22 1 time over 95% 100 cycles 0/22 0/50 Temperature Cycle Moisture Resistance Cyclic High Temperature Storage Temperature Humidity Storage Low Temperature Storage Steady State Operating Life Steady State Operating Life of High Temperature Steady State Operating Life of High Humidity Heat Steady State Operating Life of Low Temperature Permanence of Marking 100 cycles 10 cycles 1000 hrs. 1000 hrs. 1000 hrs. 1000 hrs. 1000 hrs. 500 hrs. 1000 hrs. 1 time 0/50 0/50 0/50 0/50 0/50 0/50 0/50 0/50 0/50 0/22 Ta=85°C, IF=300mA Tested with Nichia standard circuit board. 60°C, RH=90%, IF=400mA Tested with Nichia standard circuit board. Ta=-30°C, IF=350mA Tested with Nichia standard circuit board. JEITA ED-4701 500 501 JEITA ED-4701 400 403 JEITA ED-4701 300 304 Vibration Electrostatic Discharges Solvent : Isopropyl Alcohol Solvent Temperature : 20 ~ 25°C Dipping Time : 5 min. 100 ~ 2000 ~ 100Hz Sweep 4min. 200m/s2 3directions, 4cycles R=1.5kΩ, C=100pF Test Voltage=2kV 48min. 0/10 3 times Negative/Positive 0/22 Thermal resistance of LED with Nichia standard circuit board : Rja ≒ 45°C/W Nichia standard circuit board : FR4, t=1.6mm, Copper foil, t=0.07mm (2) CRITERIA FOR JUDGING DAMAGE Criteria for Judgement Item Symbol Test Conditions Min. Max. Forward Voltage VF IF=350mA Initial Level Luminous Flux IF=350mA Initial Level 0.7 φv The test is performed after the board is cooled down to the room temperature. 1.1 -3- Nichia STS-DA1-0227 7.CAUTIONS (1) Moisture Proof Package · When moisture is absorbed into the SMT package it may vaporize and expand during soldering. There is a possibility that this can cause exfoliation of the contacts and damage the optical characteristics of the LEDs. For this reason, the moisture proof package is used to keep moisture to a minimum in the package. · The moisture proof package is made of an aluminum moisture proof bag. A package of a moisture absorbent material (silica gel) is inserted into the aluminium moisture proof bag. The silica gel changes its color from blue to pink as it absorbs moisture. (2) Storage · Storage Conditions Before opening the package : The LEDs should be kept at 30°C or less and 90%RH or less. The LEDs should be used within a year. When storing the LEDs, moisture proof packaging with absorbent material (silica gel) is recommended. After opening the package : The LEDs should be kept at 30°C or less and 70%RH or less. The LEDs should be soldered within 168 hours (7days) after opening the package. If unused LEDs remain, they should be stored in the moisture proof packages, such as sealed containers with packages of moisture absorbent material (silica gel). It is also recommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bag again. · If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following condition. Baking treatment : more than 24 hours at 65 ± 5°C · Nichia LED electrodes are gold plated. The gold surface may be affected by environments which contain corrosive substances. Please avoid conditions which may cause the LED to corrode, tarnish or discolor. This corrosion or discoloration may cause difficulty during soldering operations. It is recommended that the User use the LEDs as soon as possible. · Please avoid rapid transitions in ambient temperature, especially in high humidity environments where condensation can occur. -4- Nichia STS-DA1-0227 (3) Recommended circuit · In designing a circuit, the current through each LED must not exceed the absolute maximum rating specified for each LED. It is recommended to use Circuit B which regulates the current flowing through each LED. In the meanwhile, when driving LEDs with a constant voltage in Circuit A, the current through the LEDs may vary due to the variation in forward voltage (VF) of the LEDs. In the worst case, some LED may be subjected to stresses in excess of the absolute maximum rating. (A) ... (B) ... · This product should be operated in forward bias. A driving circuit must be designed so that the product is not subjected to either forward or reverse voltage while it is off. In particular, if a reverse voltage is continuously applied to the product, such operation can cause migration resulting in LED damage. (4) Static Electricity · Static electricity or surge voltage damages the LEDs. It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. · All devices, equipment and machinery must be properly grounded. It is recommended that precautions be taken against surge voltage to the equipment that mounts the LEDs. · When inspecting the final products in which LEDs were assembled, it is recommended to check whether the assembled LEDs are damaged by static electricity or not. It is easy to find static-damaged LEDs by a light-on test or a VF test at a lower current (below 1mA is recommended). · Damaged LEDs will show some unusual characteristics such as the forward voltage becomes lower, or the LEDs do not light at the low current. Criteria : (VF > 2.0V at IF=0.5mA) -5- Nichia STS-DA1-0227 (5) LED position and orientation · Warpage of circuit board with soldered LEDs may result in damage or package breakage of the LEDs. Please pay special attention to the orientation of the LEDs as to avoid LED failure caused by bow, twist and warpage of the board. 【Non-preferable】 Cathode mark 【Preferable】 Cathode mark When mechanical stress from the board affects the soldered LED, place the LED in the preferable location and orientation as shown above. · Depending on the position and direction of LED, the mechanical stress on the LED package can be changed. Refer to the following figure. E Perforated line A C D B Slit Stress : A > B = C > D > E · When separating the circuit boards with soldered LEDs, please use appropriate tools and equipment. Hand brake without these tools and equipment may not be used. · The use of aluminum substrate increases stress to solder joints due to thermal expansion of substrate and subsequently may result in solder joint crack. Users may need to evaluate their specific application to determine any impact due to the use of aluminum substrate. -6- Nichia STS-DA1-0227 (6) Soldering Conditions · The LEDs can be soldered in place using the reflow soldering method. Nichia cannot make a guarantee on the LEDs after they have been assembled using the dip soldering method. · Recommended soldering conditions Reflow Soldering Lead Solder Pre-heat Pre-heat time Peak temperature Soldering time Condition 10 sec. Max. refer to Temperature - profile 1. 10 sec. Max. refer to Temperature - profile 2. (N2 reflow is recommended.) 120 ~ 150°C 120 sec. Max. 240°C Max. Lead-free Solder 180 ~ 200°C 120 sec. Max. 260°C Max. Temperature Soldering time 350°C Max. 3 sec. Max. (one time only) Hand Soldering Although the recommended soldering conditions are specified in the above table, reflow or hand soldering at the lowest possible temperature is desirable for the LEDs. A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature. Use the conditions shown to the under figure. [Temperature-profile (Surface of circuit board)] 2.5 ~ 5°C / sec. Pre-heating 120 ~ 150°C 60sec.Max. Above 200°C 120sec.Max. 240°C Max. 10sec. Max. 1 ~ 5°C / sec. 1 ~ 5°C / sec. Pre-heating 180 ~ 200°C 60sec.Max. Above 220°C 260°C Max. 10sec. Max. 2.5 ~ 5°C / sec. 120sec.Max. [Recommended soldering pad design] 4.1 0.6 Use the following conditions shown in the figure. 3.5 (Unit : mm) · Occasionally there is a brightness decrease caused by the influence of heat or ambient atmosphere during air reflow. It is recommended that the User use the nitrogen reflow method. · The encapsulated material of the LEDs is silicone. Therefore the LEDs have a soft surface on the top of package. The pressure to the top surface will be influence to the reliability of the LEDs. Precautions should be taken to avoid the strong pressure on the encapsulated part. So when using the chip mounter, the picking up nozzle that does not affect the silicone resin should be used. · Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. · Reflow soldering should not be done more than two times. · When soldering, do not put stress on the LEDs during heating. -7- Nichia STS-DA1-0227 (7) Cleaning · It is recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs. When using other solvents, it should be confirmed beforehand whether the solvents will dissolve the package and the resin or not. Freon solvents should not be used to clean the LEDs because of worldwide regulations. · Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition. Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur. (8) Heat Generation · Thermal design of the end product is of paramount importance. Please consider the heat generation of the LED when making the system design. The coefficient of temperature increase per input electric power is affected by the thermal resistance of the circuit board and density of LED placement on the board, as well as other components. It is necessary to avoid intense heat generation and operate within the maximum ratings given in this specification. · Please determine the operating current with consideration of the ambient temperature local to the LED and refer to the plot of Ambient temperature vs. Allowable Forward Current on CHARACTERISTICS in this specifications. Please also take measures to remove heat from the area near the LED to improve the operational characteristics of the LED. · The equation 1 indicates correlation between Tj and Ta, and the equation 2 indicates correlation between Tj and Ts. Tj=Ta + Rja W 1 Tj=Ts + Rjs W 2 Tj = Dice Temperature : °C, Ta = Ambient Temperature : °C, Ts = Solder Temperature (Cathode Side) : °C, Rja = Heat resistance from Dice to Ambient temperature : °C /W, Rjs = Heat resistance from Dice to Ts measuring point ≒ 30°C /W, W = Inputting Power (IF VF) : W (9) Others · NJSE036A complies with RoHS Directive. · The LED light output is strong enough to injure human eyes. Precautions must be taken to prevent looking directly at the LEDs with unaided eyes for more than a few seconds. · Flashing lights have been known to cause discomfort in people; you can prevent this by taking precautions during use. Also, people should be cautious when using equipment that has had LEDs incorporated into it. · The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment, communications equipment, measurement instruments and household appliances). Consult Nichia’s sales staff in advance for information on the applications in which exceptional quality and reliability are required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control systems, automobiles, traffic control equipment, life support systems and safety devices). · User shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent from Nichia. When defective LEDs are found, the User shall inform Nichia directly before disassembling or analysis. · The formal specifications must be exchanged and signed by both parties before large volume purchase begins. · The appearance and specifications of the product may be modified for improvement without notice. -8- Nichia STS-DA1-0227 0.9 520 530 0.8 540 510 0.7 ICI Chromaticity Diagram 550 560 0.6 500 0.5 E 570 D 580 590 600 B 610 620 630 y C 0.4 0.3 490 0.2 480 0.1 470 0 0 460 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 x Color Coordinates Measurement allowance is ± 0.012. -9- Forward Voltage vs. Forward Current Ta=25°C Relative Luminous Flux (a.u.) Forward Current IFP (mA) 1000 900 350 Forward Current vs. Relative Luminous Flux 2.5 Ta=25°C 2.0 1.5 1.0 0.5 0 0 200 400 600 800 1000 Forward Current IFP (mA) Allowable Forward Current IFP (mA) Duty Ratio vs. Allowable Forward Current 1000 900 650 Ta=25°C 100 50 200 Pulse Width < 10msec. = 5 10 20 50 100 Duty Ratio (%) 10 2.5 3.0 3.5 4.0 4.5 5.0 5.5 Forward Voltage VF (V) 100 1 Ambient Temperature vs. Forward Voltage IFP=350mA Relative Luminous Flux (a.u.) 5.5 Forward Voltage VF (V) Ambient Temperature vs. Relative Luminous Flux Allowable Forward Current IF (mA) 2.0 IFP=350mA 1.0 Ambient Temperature vs. Allowable Forward Current 800 650 600 452 400 352 200 0 0 -10- 5.0 4.5 4.0 3.5 3.0 0.5 Rja=35°C/W Rja=45°C/W 2.5 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (°C) 0.2 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (°C) 20 40 60 80 100 Ambient Temperature Ta (°C) Nichia STS-DA1-0227 Model NJSE036A NICHIA CORPORATION Title No. CHARACTERISTICS 080603818281 Forward Current vs. Chromaticity Coordinate (λD) Relative Emission Intensity (a.u.) Spectrum 1.2 1.0 0.8 0.6 0.4 0.2 0 350 450 550 Wavelength λ (nm) 650 Ta=25°C IFP=350mA 0.70 0.65 0.60 0.55 0.50 0.45 0.40 0 Ta=25°C 20mA(508nm) y 100mA(504nm) 350mA(500nm) 650mA(498nm) 900mA(496nm) 0.05 0.10 0.15 0.20 0.30 0.35 x Forward Current vs. Dominant Wavelength Dominant Wavelength λ D (nm) Dominant Wavelength λ D (nm) Ambient Temperature vs. Dominant Wavelength 512 508 504 500 496 492 488 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (°C) IFP=350mA Relative Illuminance (a.u.) Directivity 1.0 0° 10° 20° 30° 40° 50° 0.5 Ta=25°C IFP=350mA 0 90° 60° 30° Radiation Angle 0° 0.5 60° 70° 80° 90° 1.0 512 508 504 500 496 492 488 10 100 1000 Forward Current IFP (mA) Ta=25°C -11- Nichia STS-DA1-0227 Model NJSE036A NICHIA CORPORATION Title No. CHARACTERISTICS 080603818291 3.5 φ 2.9 0.8 3.2 0.8 3.5 3.2 Cathode mark Anode Cathode K A -12- Protection device ITEM PACKAGE ENCAPSULATING RESIN ELECTRODES MATERIALS Ceramics Silicone Resin (with Diffused) Au Plating Nichia STS-DA1-0227 NJSE036A has a protection device built in as a protection circuit against static electricity. Model 1 NJSE036A Unit mm 8/1 Scale Allow ±0.2 NICHIA CORPORATION Title No. OUTLINE DIMENSIONS 080603818391 Taping part φ 1.5+0.1 -0 8±0.1 2±0.05 4±0.1 1.75±0.1 0.2±0.05 3.85±0.1 Reel part φ 180+0 -3 15.4±1 13+1 -0 5.5±0.05 Cathode mark 12+0.3 - 0.1 φ2 1 ±0.8 ±0.2 φ 13 φ 1.5+0.2 -0 3.85±0.1 1±0.1 Label XXXX LED TYPE NJSx036xT LOT xxxxxxQTY pcs RoHS Reel End of tape No LEDs LEDs mounting part No LEDs φ 60+1 -0 Pull direction Top cover tape Embossed carrier tape -13Reel Lead Min.160mm (No LEDs) Reel Lead Min.100mm (No LEDs) Reel Lead Min.400mm 2,000pcs/Reel Nichia STS-DA1-0227 Taping is based on the JIS C 0806 : Packaging of Electronic Components on Continuous Tapes. Model NJSx036xT Unit mm Scale Allow NICHIA CORPORATION Title No. TAPING DIMENSIONS 080603818421 Nichia STS-DA1-0227 The reel and moisture absorbent material are put in the moisture proof foil bag and then heat sealed. Reel Label NICHIA Seal XXXX LED TYPE LOT QTY NJSx036xT xxxxxxRoHS PCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Moisture absorbent material Moisture proof foil bag The box is partitioned with the cardboard. Label NICHIA Nichia LED XXXX LED TYPE RANK QTY NJSx036xT PCS RoHS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Packing unit Moisture proof foil bag Cardboard box Cardboard box S Cardboard box M Cardboard box L Reel/bag 1reel Quantity/bag (pcs) 2,000 MAX. Reel/box 5reel MAX. 10reel MAX. 20reel MAX. Quantity/box (pcs) 10,000 MAX. 20,000 MAX. 40,000 MAX. Dimensions (mm) 291 237 120 8t 259 247 243 5t 444 262 259 8t Model NJSx036xT NICHIA CORPORATION Title No. PACKING 070921700171 -14-