F310G476MBA

CONDUCTIVE POLYMER TANTALUM SOLID ELECTROLYTIC CAPACITORS F31 Conductive Polymer Resin-molded Chip, Compact Series Adapted to the RoHS directive (2002/95/EC). Specifications Item Category Temperature Range Capacitance Tolerance Dissipation Factor(at 120Hz) ESR (100kHz) Leakage Current Ripple Current Damp Heat (Steady State) Temperature Cycles Type numbering system (Example : 6.3V 47µF) 1 2 4 3 5 0 J F 3 1 6 7 8 9 10 11 4 7 6 M B A Taping code (Refer to page 302 for details) Resistance to Soldering Heat Case code Capacitance tolerance Rated Capacitance Rated voltage Surge Series Endurance 1 Dimensions L W1 H Endurance 2 W2 S S Case code L W1 W2 H S P 2.0± 0.2 1.25± 0.1 0.9± 0.1 1.1± 0.1 0.5± 0.2 (mm) A 3.2± 0.2 1.6± 0.2 1.2± 0.1 1.1± 0.1 0.8 ± 0.2 B 3.4 ± 0.2 2.8 ± 0.2 2.3 ± 0.1 1.1± 0.1 0.8 ± 0.2 Shear Test 1mm Terminal Strength Marking P Case A Case Conductive Polymer Rated Capacitance ( µF) Jar Capacitance code B Case Capacitance Ja Rated Voltage code code 33 P6v Month Conductive Polymer code Rated Voltage code Month code Rated Voltage (6.3V is marked as "6V " ) Standard ratings V Cap. (µF) Code Performance Characteristics Ð55 to +105ûC (Rated temperature + 85ûC) ±20% (120Hz) Refer to the list below Refer to the list below After 5 minutes' application of rated voltage, leakage current at 20ûC is not more than 0.1CV Refer to the list below At 60ûC, 90 to 95% R.H. 500hours (No voltage applied) Capacitance Change..Within Ð20 to +30% of initial value Dissipation Factor.......1.5 times Initial specified value or less Leakage Current.........Initial specified value or less Ð55ûC / +105ûC 30 minutes each 5 cycle Capacitance Change..Within ±20% of initial value Dissipation Factor.......Initial specified value or less Leakage Current.........Initial specified value or less Test Condition;10 second reflow at 240ûC Capacitance Change..Within ±20% of initial value Dissipation Factor.......1.3 times Initial specified value or less Leakage Current.........Initial specified value or less After application of surge voltage in series with a 1k½ resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85ûC, capacitors meet the characteristics requirements listed below. Capacitance Change...Within ±20% of initial value Dissipation Factor........Initial specified value or less Leakage Current..........Initial specified value or less After 1000 hours' application of rated voltage in series with a 3½ resistor at 85ûC. Capacitance Change....Within ±20% of initial value Dissipation Factor...1.5 times Initial specified value or less Leakage Current...Initial specified value or less After 1000 hours' application of rated voltage in series with a 3½ resistor at 105ûC,capacitors meet the characteristic requirements listed below Capacitance Change....Within ±20% of initial value Dissipation Factor...3 times Initial specified value or less Leakage Current...Initial specified value or less After applying the pressure load of 5N for 10±1 seconds horizontally to the center of capacitor side body which has no electrode and has been soldered beforehand on an aluminum substrate, there shall be 5N (0.51kg ¥ f) found neither exfoliation nor its sign at the For 10±1 seconds terminal electrode. Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of the capacitor, the pressure strength is applied with 20 R230 a specified jig at the center of the substrate so that the substrate may bend by 1mm as illustrated. Then, 45 45 there shall be found no remarkable abnormality on the capacitor terminals. 2.5 4 6.3 10 0E 0G 0J 1A code P P A a P (P) ¥ A (A) ¥ B Capacitance 10 106 22 226 P 33 336 A A (A) ¥ B B n 47 476 A (A) ¥ B B B s 68 686 100 107 B B B (B) ( ) The series in parentheses are being developed. Please contact to your local Nichicon sales office when these series are being designed in your application. ∗ As for the surge voltage refer to page 301 for details. Standard ratings Rated Case Rated Volt Capacitance code (V ) (µF) Leakage Disspation ESR Rated Ripple Factor Current Part Number (µA) (%@120Hz) (m½@100kHz) (mArms@100kHz) 354 200 6 5.5 F310E226MPA P 22 632 150 6 8.3 F310E336MAA A 33 2.5 632 150 6 11.8 F310E476MAA A 47 1035 70 8 F310E107MBA 25.0 B 100 354 200 6 4.0 F310G106MPA P 10 354 200 6 8.8 F310G226MPA P 22 4 632 150 6 F310G336MAA 13.2 A 33 1035 70 8 F310G476MBA 18.8 B 47 1035 70 8 F310G107MBA 40.0 B 100 354 200 6 6.3 F310J106MPA P 10 548 200 6 13.9 F310J226MAA A 22 1035 70 8 20.8 F310J336MBA B 33 6.3 1035 70 (55) 8 29.6 F310J476MBA B 47 1035 70 8 42.8 F310J686MBA B 68 548 200 6 10.0 F311A106MAA A 10 1035 70 8 22.0 F311A226MBA B 22 10 1035 70 8 33.0 F311A336MBA B 33 1035 70 8 47.0 F311A476MBA B 47 ( ) ESR specification types are also available ( ) upon S request. f Please contact to your local Nichicon sales office when these series are being designed in your application. CAT.8100X