F910J107MCC

SOLID TANTALUM ELECTROLYTIC CAPACITORS F91 LOW ESR Resin-molded Chip Compliant to the RoHS directive (2002/95/EC). Specifications Item Performance Characteristics Category Temperature Range Capacitance Tolerance Dissipation Factor (120Hz) ESR (100kHz) --55 to +125˚C (Rated temperature : +85˚C) ± 20%, ±10% (at 120Hz) Refer to the table below. Refer to the table below. • After 1 minute's application of rated voltage, leakage current at 20˚C is not more than 0.01CV or 0.5µA, whichever is greater. • After 1 minute's application of rated voltage, leakage current Leakage Current at 85˚C is not more than 0.1CV or 5µA, whichever is greater. • After 1 minute's application of derated voltage, leakage current at 125˚C is not more than 0.125CV or 6.3µA, whichever is greater. Capacitance Change by Temperature Type numbering system (Example : 10V 100µF) 1 2 3 4 5 6 7 8 9 10 F 9 1 1 A 1 0 7 M C Damp Heat (Steady State) 11 Taping code (Refer to page 333 for details) Case code Capacitance tolerance Rated capacitance Rated voltage Temperature Cycles Series Capacitance Change Within ±5% of the initial value Dissipation Factor......Initial specified value or less Leakage Current........Initial specified value or less to Soldering Heat C • N Case L W1 Surge∗ After application of surge in series with a 33Ω resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 sucessive test cycles at 85˚C, capacitors shall meet the characteristic requirements table below. Capacitance Change....Within ±5% of the initial value Dissipation Factor........Initial specified value or less Leakage Current..........Initial specified value or less Endurance∗ After 2000 hours' application of rated voltage in series with a 3Ω resistor at 85 ˚C , or derated voltage in series with a 3 Ω resistor at 125 ˚C , capacitors shall meet the characteristics requirements table below. Capacitance Change......Within ±10% of the initial value Dissipation Factor..........Initial specified value or less Leakage Current............Initial specified value or less Shear Test After applying the pressure load of 5N for 10±1 seconds horizontally to the center of capacitor side body which has no electrode and has been soldered beforehand on a substrate, there shall 5N (0.51kg ¥ f) be found neither exfoliation nor its sign For 10±1 seconds at the terminal electrode. Terminal Strength Keeping a capacitor surface20 mounted on a substrate upside down R230 and supporting the substrate at both of the opposite bottom points 45mm apart from the center of capacitor, 45 45 the pressure strength is applied with a specified jig at the center of substrate so that the substrate may bend by 1mm as illustrated. Then, there shall be found no remarkable abnormality on the capacitor terminals. H W2 S S Dimensions (mm) L 6.0 ± 0.2 W1 W2 H C 3.2 ± 0.2 2.2 ± 0.1 2.5 ± 0.2 S 1.3 ± 0.2 N 7.3 ± 0.2 4.3 ± 0.2 2.4 ± 0.1 2.8 ± 0.2 1.3 ± 0.2 220 10V N Case 68 10V C Case ∗ As for the surge and derated voltage at 125˚C, refer to page 332 for details. Rated voltage (V) Rated voltage (V) Rated Capacitance (µF) Rated Volt Standard Ratings V Code 4 0G 1mm Marking Cap. (µF) At 40˚C 90 to 95% R.H. 500 hours (No voltage applied) Capacitance Change Within ±10% of the initial value Dissipation Factor......Initial specified value or less Leakage Current........Initial specified value or less --55˚C / +125˚C 30 minutes each 5 cycles Capacitance Change Within ±5% of the initial value Dissipation Factor......Initial specified value or less Leakage Current........Initial specified value or less 10 seconds reflow at 260˚C, 5 seconds immersion at 260˚C Resistance Drawing Case Code +15% Max. (at . +125˚C) +10% Max. (at +85˚C) --10% Max. (at --55˚C) 6.3 0J 10 1A C 068 686 100 107 C C 150 157 C C N 220 227 C C•N N 330 337 N N N 470 477 N N 680 687 N 4V 6.3V 10V Rated Capacitance (µF) Case code Part Number Leakage Current (µA) Disspation Factor (% @120Hz) ESR (mΩ@100kHz) 150 220 330 470 680 100 150 220 220 330 470 68 100 150 220 330 C C N N N C C C N N N C C N N N F910G157MCC F910G227MCC F910G337MNC F910G477MNC F910G687MNC F910J107MCC F910J157MCC F910J227MCC F910J227MNC F910J337MNC F910J477MNC F911A686MCC F911A107MCC F911A157MNC F911A227MNC F911A337MNC 6.0 8.8 13.2 18.8 27.2 6.3 9.5 13.9 13.9 20.8 29.6 6.8 10.0 15.0 22.0 33.0 12 12 10 16 18 8 12 14 10 14 16 8 10 10 12 18 250 250 100 100 100 250 250 250 100 100 100 300 250 100 100 100 In case of capacitance tolerance system. ± 10% type, K will be put at 9th digit of type numbering CAT.8100B