F950J107MSAAM1Q2

SOLID TANTALUM ELECTROLYTIC CAPACITORS MUSE F95 Conformal coated Chip, For Mobile Audio Specifications Compliant to the RoHS directive (2002/95/EC). Item Per formance Characteristics Category --55 to +125˚C (Rated temperature : +85˚C) Temperature Range Capacitance Tolerance ± 20%, ± 10% (at 120Hz) Dissipation Factor Refer to next page (at 120Hz) ESR(100kHz) Applications Mobile Audio Player Smartphone Mobile phone Wireless Microphone System Feature Rich sound in the bass register and clear sound,Materials are strictly selected to achieve high level sound. F95 series has no lead-frame, and no vibration factor. Low ESR, Low ESL Line up miniature size and high capacitance, necessary to mobile design. Surge∗ After application of surge voltage in series with a 33Ω resistor at the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive test cycles at 85˚C, capacitors shall meet the characteristic requirements table below. Capacitance Change • • • • • • Refer to next page (*1) Dissipation Factor • • • • • • • • • • Initial specified value or less Leakage Current • • • • • • • • • • • • Initial specified value or less Endurance∗ After 2000 hours' application of rated voltage at 85˚C, capacitors shall meet the characteristic requirements table below. Capacitance Change • • • • • • Refer to next page (*1) Dissipation Factor • • • • • • • • • • Initial specified value or less Leakage Current • • • • • • • • • • •• Initial specified value or less Type numbering system (Example : 4V 220µF) 1 2 3 4 5 6 7 8 9 10 11 F 9 5 0 G 2 2 7 M S 12 13 14 15 16 AM1 Q 2 Shear Test Single face electrode MUSE series code Taping code (Refer to page 333 for details) Terminal Strength Capacitance tolerance Rated capacitance Rated voltage After applying the pressure load of 5N for 10 ± 1 seconds horizontally to the center of capacitor side body which has no electrode and has been soldered 5N (0.51kg • f) beforehand on a substrate, there shall be For 10 ± 1 seconds found neither exfoliation nor its sign at the terminal electrode. Keeping a capacitor surface-mounted on a substrate upside down and supporting the substrate at both of the opposite bottom points 45mm apart from the center of capacitor, the pressure strength is applied with 20 R230 a specified jig at the center of substrate so that the substrate may bend by 1mm as illustrated. Then, 45 45 there shall be found no remarkable abnormality on the capacitor terminals. 1mm Case code Refer to next page Refer to next page Provided that • After 1 minute's application of rated voltage, leakage current at 85˚C, Leakage Current 10 times or less than 20˚C specified value. • After 1 minute's application of rated voltage, leakage current at 125˚C, 12.5 times or less than 20˚C specified value. Capacitance Change +15% Max. (at +125˚C) +10% Max. (at + 85˚C) by Temperature --10% Max. (at --55˚C) At 40˚C, 90 to 95% R.H., For 500 hours (No voltage applied) Damp Heat Capacitance Change • • • • • • Refer to next page (*1) Dissipation Factor • • • • • • • • • • Initial specified value or less (Steady State) Leakage Current • • • • • • • • • • • • Initial specified value or less At --55˚C / +125˚C, 30 minutes each, For 5 cycles, Capacitance Change • • • • • • Refer to next page (*1) Temperature Cycles Dissipation Factor • • • • • • • • • • Initial specified value or less Leakage Current • • • • • • • • • • •• Initial specified value or less 10 seconds reflow at 260˚C, 10 seconds immersion at 260˚C Resistance to Capacitance Change • • • • • • • • • Refer to next page (*1) Soldering Heat Dissipation Factor • • • • • • • • • • • • • Initial specified value or less Leakage Current • • • • • • • • • • •• • • • Initial specified value or less ∗ As for the surge voltage, refer to page 332 for details. Series Dimensions Drawing L W H Resin Case code P S A T B L W 2.2 ± 0.3 1.25 ± 0.3 3.2 ± 0.3 1.6 ± 0.3 3.2 ± 0.3 1.7 ± 0.3 3.5 ± 0.2 2.7 ± 0.2 3.5 ± 0.2 2.8 ± 0.2 (mm) H 1.0 ± 0.2 1.0 ± 0.2 1.4 ± 0.2 1.0 ± 0.2 1.8 ± 0.2 A 0.6 ± 0.3 0.8 ± 0.3 0.8 ± 0.3 0.8 ± 0.2 0.8 ± 0.3 B 0.8 ± 0.3 1.2 ± 0.3 1.2 ± 0.3 1.2 ± 0.2 1.2 ± 0.3 C 0.8 ± 0.3 0.8 ± 0.3 0.8 ± 0.3 1.1 ± 0.2 1.1 ± 0.3 (D) (0.2) (0.2) (0.2) (0.2) (0.2) D dimension only for reference Solder electrode Solder electrode A B C (D) Single-side electrodes (Both electrodes at bottom side only) CAT.8100B SOLID TANTALUM ELECTROLYTIC CAPACITORS MUSE F95 Standard Ratings Cap. (µF) Marking V 4 6.3 10 Code 0G 0J 1A 68 686 S S B 100 107 S S•T B 150 157 S (A) 220 227 (P) • S • T (A) • (T) • B 330 337 T B 470 477 (T) • B (B) 680 687 S•A case T•B Case J8 J8 Rated Capacitance code µF code (T) • (B) ( ) The series in parentheses are being developed. 68 W7 100 A8 150 E8 220 J8 330 N8 470 S8 680 W8 P case - No marking on part. Please contact to your local Nichicon sales office when these series are being designed in your application. Standard Ratings Rated Rated Volt Capacitance Case code (µF) 4V 6.3V 10V Part Number ∗ 68 S F950G686MSAAM1Q2 2.7 10 0.8 100 S F950G107MSAAM1Q2 4.0 14 0.8 ∗ 150 S F950G157MSAAM1Q2 6.0 22 0.8 ± 15 220 S F950G227MSAAM1Q2 8.8 30 0.8 ± 15 220 T F950G227MTAAM1Q2 8.8 25 0.6 ∗ 330 T F950G337MTAAM1Q2 13.2 40 0.8 ± 20 470 B F950G477MBAAM1Q2 18.8 40 0.4 ± 20 68 S F950J686MSAAM1Q2 4.3 14 0.9 ∗ 100 S F950J107MSAAM1Q2 6.3 20 0.9 ± 15 100 T F950J107MTAAM1Q2 6.3 14 0.6 ∗ 220 B F950J227MBAAM1Q2 13.9 30 0.4 ∗ 330 B F950J337MBAAM1Q2 20.8 35 0.6 ± 20 68 B F951A686MBAAM1Q2 6.8 12 0.4 ∗ 0.4 ∗ 100 B F951A107MBAAM1Q2 In case of capacitance tolerance system. *1 : ∆C/C Disspation *2 *1 ESR Leakage Current Factor ∆C/C (Ω@100kHz) (%@120Hz) (µA) (%) 10.0 14 ± 10% type, K will be put at 9th digit of type numbering Marked "∗" Item Damp Heat Tempereature cycles Resistance soldering heat Surge Endurance S • A • T • B Case (%) ±10 ±5 ±5 ±5 ±10 *2 : Leakage Current After 1 minute's application of rated voltage, leakage current at 20˚C. CAT.8100B