GYC1E221MCQ1GS

CONDUCTIVE POLYMER HYBRID ALUMINUM ELECTROLYTIC CAPACITORS GYC NEW Chip Type, 135°C High Reliability High Reliability, Low ESR,High ripple current. Long life of 2000 to 4000 hours at 135°C. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. GYC High Temperature GYA Specifications Item Performance Characteristics Category Temperature Range – 55 to +135°C Rated Voltage Range 25 to 63V Rated Capacitance Range 10 to 330µF Capacitance Tolerance ± 20% at 120Hz, 20°C Tangent of loss angle (tan δ) 25 0.14 Rated voltage (V) tan δ (MAX.) 35 0.12 50 0.10 63 0.08 120Hz 20°C Less than or equal to the specified value at 100kHz, 20°C ESR Leakage Current After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01CV(µA). Temperature Characteristics (Max.Impedance Ratio) Z– 25°C / Z+20°C Z– 55°C / Z+20°C Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after D.C. bias plus rated ripple current is applied for 4000 hours (2000 hours for φD = 6.3) at 125°C or 135°C, the peak voltage shall not exceed the rated voltage. 2 2.5　(100kHz) Within ± 30% of initial capacitance value 200% or less of the initial specified value 200% or less of the initial specified value Less than or equal to the initial specified value Capacitance change tan δ ESR Leakage current After storing the capacitors under no load at 135°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. Shelf Life Damp Heat (Steady State) The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours (1000 hours for φD = 6.3) at 85°C, 85% RH. Capacitance change tan δ Leakage current Within±30% of the initial capacitance value 200% or less of the initial specified value Less than or equal to the initial specified value Resistance to Soldering Heat The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250°C. The capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20°C. Capacitance change tan δ Leakage current Within±10% of the initial capacitance value Less than or equal to the initial specified value Less than or equal to the initial specified value Marking Black print on the case top. Dimensions Series 0.3 MAX. 1 0.5 MAX. Plastic platform Voltage (V:35V) Type numbering system (Example : 35V 47µF) Positive (φ6.3 ) C±0.2 2 3 4 5 6 7 8 9 10 11 12 13 14 GYC 1 V 4 7 0 MCQ 1 GS Taping code A±0.2 E B ±0.2 φD±0.5 A1 47V GYC Size code Configuration Capacitance tolerance (±20%) Rated capacitance (47µF) Lot No. L ±0.3 Capacitance Rated voltage (35V) Negative H Series name Type Positive Series 0.3 MAX. Capacitance B ±0.2 φD±0.5 A1 56J GYC Lot No. C±0.2 L ±0.5 E Voltage (J:63V) Trade mark 0.5 MAX. Plastic platform H (mm) φD×L A A±0.2 (φ8, φ10 ) Negative φ6.3 × 5.8 φ6.3 × 7.7 7.3 7.3 φ8 × 10 9.0 φ10 × 10 11.0 B 6.6 6.6 8.3 10.3 C 6.6 6.6 8.3 10.3 E 2.2 2.2 3.1 4.5 L 5.8 7.7 10.3 10.3 H Voltage V 25 35 50 63 Code E V H J 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 φ6.3× 7.7L , φ8× 10L , φ10× 10L : The vibration structure-resistant product is also available upon request, please ask for details. Dimension table in next page. 116 CONDUCTIVE POLYMER HYBRID ALUMINUM ELECTROLYTIC CAPACITORS GYC Dimensions Co Cap.(µF) V (Code) 25 35 50 de 1E 1V 1H 10 100 22 220 6.3 × 5.8 80 1100 750 33 330 6.3 × 7.7 45 1600 1100 47 470 56 560 68 680 8 × 10 30 2200 1250 100 101 10 × 10 28 2600 1600 150 151 220 221 270 271 50 6.3 × 7.7 1400 35 60 1400 900 6.3 × 7.7 40 1900 1400 900 1900 1400 8 × 10 27 2900 8 × 10 27 2900 1600 10 × 10 20 3300 2000 1600 φD×L 330 10 × 10 331 Co Cap.(µF) 6.3 × 5.8 6.3 × 5.8 20 V (Code) 63 de 1J 3300 2000 10 100 6.3 × 5.8 120 1000 700 22 220 6.3 × 7.7 80 1300 900 33 330 8 × 10 40 1900 1100 47 470 56 560 10 × 10 30 2300 1400 68 680 φD×L ESR mΩ Rated ripple Current (mArms) 125℃ 135℃ ESR at 20°C 100kHz Rated ripple Current at 125°C or 135°C 100kHz Frequency coefficient of rated ripple current 0 Frequency0/ Coefficient 120Hz 0.15 1kHz­ 0.40 10kHz 100kHz or more 0.75 1.00 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18,19. Please refer to page 3 for the minimum order quantity. 117 ESR mΩ Rated ripple Current (mArms) 125℃ 135℃