LAR2D152MELB40

ALUMINUM ELECTROLYTIC CAPACITORS LAR Snap-in Terminal Type, 105°C Permissible Overvoltage Withstanding 2000 hours application of rated ripple current at 105°C. Reduction of short incidence when overvoltage (rated voltage x 1.5) is applied to a capacitor. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). LAR Permissible Overvoltage LGU Specifications Item Performance Characteristics Category Temperature Range – 40 to +105˚C (200 250V), – 25 to +105˚C (400 450V) Rated Voltage Range 200 to 450V Rated Capacitance Range 82 to 2200µF Capacitance Tolerance ± 20% at 120Hz, 20˚C Leakage Current I 3 CV (µA) (After 5 minutes' application of rated voltage [C : Rated Capacitance(µF), V : Voltage ( V ) ] Rated voltage (V) tan δ (MAX.) Tangent of loss angle (tan δ) 200 to 400 0.15 Rated voltage(V) Z – 25°C / Z+20°C Impedance ratio Z – 40°C / Z+20°C ZT/Z20(MAX.) Stability at Low Temperature Measurement frequency : 120Hz at 20˚C 450 0.20 200 • 250 3 12 Measurement frequeny : 120Hz 400 • 450 8 ----- Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after D.C. bias plus rated ripple current is applied for 2000 hours at 105°C, the peak voltage shall not exceed the rated voltage. Capacitance change tan δ Leakage current Within ±20% of the initial capacitance value 200% or less than the initial specified value Less than or equal to the initial specified value Shelf Life After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the requirements listed at right. Capacitance change tan δ Leakage current Within ±15% of the initial capacitance value 150% or less than the initial specified value Less than or equal to the initial specified value Safety Performance When overvoltage (rated voltage x 1.5, limited current = 1A) is applied to a capacitor, the pressure relief vent will operate normally more than 60% of the time without short and flame. Marking Printed with white color letter on black sleeve. Drawing Type numbering system (Example : 400V 120µF) Polarity bar Sleeve (P.E.T.) Polarity bar 1 +1.5 MAX. φD +1.5 φDMAX. 2 3 4 5 6 7 8 10 L2 4.00.5 Pressure relief vent L±2  4.0±0.5 0.8 10 0 .1 13 14 Capacitance tolerance (±20%) Configuration Rated capacitance (120µF) Capacitance tolerance (20%) +0.2 -0.1 0.8 voltage (400V) RatedRated Capacitance (120F) .2 +0 .1 -0 0.8 Series(400V) name Rated voltage Type Series name .2 +0 .1 -0 Case length code Case dia. code Case length code φD dia. Code Case code 22 Z Code φD 25 A Z 22 30 B A 25 35 C B 30 C 35 Type (2.5) 2.5 2-2φ±0.1 +0.2 -0.1 0.8  4.0±0.5 4.00.5 0.1 10 11 12 Configuration (1 0) Pressure relief vent 10 ± 9 L1 A L 12 Z 13 3 14 0 2 R 3 2 4 G 5 1 6 2 7 1 8 M 9 E 10 11 L AR 2 G 1 2 1 ME L Z 3 0 Sleeve (P.E.T.) +0.2 0.1 2-2φ± (PC board hole dimensions) 1.5 -0.11.5 +0.2 -0.1 (Terminal dimensions) (PC board hole dimensions) (Terminal dimensions) The other terminal is also available upon request. Please refer to page " Snap-in Terminal type Terminal-Shape " for schematic of dimensions. Frequency coefficient of rated ripple current Frequency(Hz) coeff. 50 60 120 300 1k 10k 50k or more 200 , 250V 0.81 0.85 1.00 1.17 1.32 1.45 1.50 400 , 450V 0.77 0.82 1.00 1.16 1.30 1.41 1.43 Minimum order quantity : 50pcs. Dimension table in next page. CAT.8100K ALUMINUM ELECTROLYTIC CAPACITORS LAR Dimensions 200V (2D) 250V (2E) Rated ripple Leakage Current (mArms) (mA) 22 × 25 22 × 30 1310 0.83 LAR2D391MELZ25 1480 0.91 LAR2D471MELZ30 1480 0.91 LAR2D471MELA25 560 25 × 25 22 × 35 1600 1.00 LAR2D561MELZ35 1750 1.10 LAR2D681MELZ40 680 22 × 40 25 × 30 1750 1.10 LAR2D681MELA30 30 × 25 22 × 45 1750 1.10 LAR2D681MELB25 2040 1.21 LAR2D821MELZ45 25 × 35 22 × 50 2040 1.21 LAR2D821MELA35 2300 1.34 LAR2D102MELZ50 25 × 45 30 × 30 2300 1.34 LAR2D102MELA45 2300 1.34 LAR2D102MELB30 35 × 25 25 × 50 2300 1.34 LAR2D102MELC25 2650 1.46 LAR2D122MELA50 30 × 35 35 × 30 2650 1.46 LAR2D122MELB35 2650 1.46 LAR2D122MELC30 1500 30 × 40 35 × 35 2800 1.64 LAR2D152MELB40 2800 1.64 LAR2D152MELC35 1800 30 × 50 35 × 40 3080 1.80 LAR2D182MELB50 3080 1.80 2200 35 × 45 3480 1.98 LAR2D182MELC40 LAR2D222MELC45 Cap. (µF) 390 470 820 1000 1200 Size φD × L(mm) Code Cap. (µF) Rated ripple Leakage Current (mArms) (mA) 22 × 25 22 × 30 1100 0.77 1200 0.86 LAR2E331MELZ30 25 × 25 22 × 35 1200 0.86 LAR2E331MELA25 1300 0.93 LAR2E391MELZ35 25 × 30 22 × 40 1300 0.93 LAR2E391MELA30 1400 1.02 LAR2E471MELZ40 25 × 35 30 × 25 1400 1.02 LAR2E471MELA35 1400 1.02 LAR2E471MELB25 22 × 45 25 × 35 1500 1.12 LAR2E561MELZ45 1500 1.12 LAR2E561MELA35 30 × 30 22 × 50 1500 1.12 LAR2E561MELB30 1700 1.23 LAR2E681MELZ50 25 × 40 30 × 30 1700 1.23 LAR2E681MELA40 1700 1.23 LAR2E681MELB30 35 × 25 25 × 45 1700 1.23 LAR2E681MELC25 2000 1.35 LAR2E821MELA45 30 × 35 35 × 30 2000 1.35 LAR2E821MELB35 2000 1.35 LAR2E821MELC30 1000 30 × 40 35 × 35 2200 1.50 LAR2E102MELB40 2200 1.50 LAR2E102MELC35 1200 30 × 45 35 × 40 2300 1.64 LAR2E122MELB45 2300 1.64 LAR2E122MELC40 35 × 45 35 × 50 2500 1.83 1800 2700 2.01 LAR2E152MELC45 LAR2E182MELC50 Cap. (µF) Size φD × L(mm) Rated ripple Leakage Current (mArms) (mA) 22 × 25 22 × 30 340 0.57 690 0.63 LAR2W101MELZ30 25 × 25 22 × 35 690 0.63 LAR2W101MELA25 720 0.69 LAR2W121MELZ35 25 × 30 22 × 40 720 0.69 LAR2W121MELA30 790 0.77 LAR2W151MELZ40 25 × 30 30 × 25 790 0.77 LAR2W151MELA30 790 0.77 LAR2W151MELB25 22 × 45 25 × 35 870 0.85 LAR2W181MELZ45 870 0.85 LAR2W181MELA35 270 330 390 470 560 680 820 1500 Size φD × L(mm) 400V (2G) Cap. (µF) 100 Size φD × L(mm) Leakage Current (mArms) (mA) Code 22 × 25 22 × 30 680 0.60 LAR2G101MELZ25 730 0.65 LAR2G121MELZ30 950 0.80 LAR2G181MELZ35 180 22 × 35 25 × 30 950 0.80 LAR2G181MELA30 30 × 25 22 × 45 950 0.80 LAR2G181MELB25 270 330 390 470 560 680 LAR2E271MELZ25 450V (2W) Rated ripple 120 220 Code 1100 0.88 LAR2G221MELZ45 25 × 35 30 × 25 1100 0.88 LAR2G221MELA35 1100 0.88 LAR2G221MELB25 22 × 50 25 × 40 1220 0.98 LAR2G271MELZ50 1220 0.98 LAR2G271MELA40 30 × 30 35 × 25 1220 0.98 LAR2G271MELB30 1220 0.98 LAR2G271MELC25 25 × 45 30 × 35 1440 1.08 LAR2G331MELA45 1440 1.08 LAR2G331MELB35 25 × 50 30 × 40 1550 1.18 LAR2G391MELA50 1550 1.18 LAR2G391MELB40 35 × 30 30 × 45 1550 1.18 LAR2G391MELC30 1680 1.30 LAR2G471MELB45 35 × 35 30 × 50 1680 1.30 LAR2G471MELC35 1900 1.41 LAR2G561MELB50 35 × 40 35 × 45 1900 1.41 2120 1.56 LAR2G561MELC40 LAR2G681MELC45 82 100 120 150 180 Code LAR2W820MELZ25 870 0.85 LAR2W181MELB30 1050 0.94 LAR2W221MELA40 30 × 30 35 × 25 1050 0.94 LAR2W221MELB30 1050 0.94 LAR2W221MELC25 25 × 50 30 × 35 1230 1.04 LAR2W271MELA50 1230 1.04 LAR2W271MELB35 35 × 30 30 × 40 1230 1.04 LAR2W271MELC30 1380 1.15 LAR2W331MELB40 35 × 35 30 × 50 1380 1.15 LAR2W331MELC35 1610 1.25 LAR2W391MELB50 1610 1.25 LAR2W391MELC40 470 35 × 40 35 × 45 1780 1.37 560 35 × 50 1990 1.50 LAR2W471MELC45 LAR2W561MELC50 30 × 30 25 × 40 220 270 330 390 Rated ripple current (mArms) at 105°C 120Hz CAT.8100K