LQSW6391MELC35

ALUMINUM ELECTROLYTIC CAPACITORS LQS Snap-in Terminal type, 105°C High speed charge-discharge. Suited for high frequency regenerative voltage for AC servomotor, general inverter. Suited for equipment used at valtage fluctuating area. Suited for rectifier circuit of voltage doubler Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). LQS Hi speed chargedischarge LGU Specifications Item Performance Characteristics Category Temperature Range – 25 to +105°C Rated Voltage Range 350 to 450V Rated Capacitance Range 82 to 820µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current I 3 CV (µA) (After 5 minutes' application of rated voltage [C : Rated Capacitance(µF), V : Voltage ( V ) ] Measurement frequency : 120Hz at 20°C Rated voltage (V) tan δ (MAX.) Tangent of loss angle (tan δ) 350 0.15 Rated voltage (V) Stability at Low Temperature Impedance ratio ZT/Z20(MAX.) 400 0.15 420 0.15 450 0.20 Measurement frequency : 120Hz 350 to 450 Z – 25°C / Z+20°C 8 Capacitance change tan δ Leakage current Appearance Within ±20% of the initial capacitance value 300% or less than the initial specified value Less than or equal to the initial specified value There shell be found to remarkable abnormality on the capacitor Endurance of chargedischarge behavior After an application of charge-discharge voltage for 50million times (charge-discharge voltage difference(ΔV) = rated voltage × 0.35, cycle 6Hz) capacitors shell meet the characteristics requirement listed at right. Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after D.C. bias plus rated ripple current is applied for 3000 hours at 105°C, the peak voltage shall not exceed the rated voltage. Shelf Life After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified value for endurance characteristics listed above. Marking Printed with white color letter on black sleeve. Drawing 1 +1.5MAX. φDMAX. φD +1.5 4.0±0.5 L±2 Pressure relief vent 4.0±0.5 0.8 4.0±0.5 4.0±0.5 0.8 5 6 7 8 9 10 11 12 13 14 Configuration (1 0) Capacitance tolerance (±20%) Configuration +0.2 -0.1 +0.2 -0.1 0.8 voltage(180µF) (400V) RatedRated capacitance .2 +0 .1 -0 Series(400V) name Rated voltage Type Series name .2 +0 1 8 -0. 0. Case length code Case dia. code Case length code φD dia. Code Case code 22 Z φD Code 25 A 22 Z 30 B 25 A 35 C 30 B 35 C Please contact to us if other configurations areType required. (2.5) (2.5) 2-2φ±0.1 4 Rated capacitance (180µF) Capacitance tolerance (±20%) Pressure relief vent 0.1 3 (1 0) L±2 10 ± 2 L1 Q2 S3 24 G5 16 87 18 M 0 9 E 10 L 11 A 12 3 13 14 L QS 2 G 1 8 1 ME L A 3 0 Sleeve (P.E.T.) 0.1 Within ±20% of the initial capacitance value 200% or less than the initial specified value Less than or equal to the initial specified value Type numbering system (Example : 400V 180µF) Polarity bar Sleeve (P.E.T.) Polarity bar 10 ± Capacitance change tan δ Leakage current Please contact to us if other configurations are required. 1.5 +0.2 -0.1 0.1 2-2φ± (PC board hole dimensions) 1.5 +0.2 -0.1 (Terminal dimensions) (PC board hole dimensions) (Terminal dimensions) Other terminations available upon request. Please refer to the Guidelines for Aluminum Electrolytic Capacitors. Minimum order quantity : 50pcs. Dimension table in next page. CAT.8100K ALUMINUM ELECTROLYTIC CAPACITORS LQS Dimensions 400V (2G) 350V (2V) Cap. (µF) Cap. (µF) Size φD × L(mm) Rated ripple Leakage Current (mArms) (mA) 22 × 25 22 × 30 750 0.61 LQS2V121MELZ25 100 820 0.68 LQS2V151MELZ30 120 180 22 × 30 25 × 25 900 0.75 LQS2V181MELZ30 150 900 0.75 LQS2V181MELA25 220 22 × 35 25 × 30 1000 0.83 LQS2V221MELZ35 1000 0.83 LQS2V221MELA30 22 × 40 25 × 35 1100 0.92 LQS2V271MELZ40 1100 0.92 LQS2V271MELA35 30 × 25 22 × 45 1100 0.92 LQS2V271MELB25 1200 1.01 LQS2V331MELZ45 25 × 40 30 × 30 1200 1.01 LQS2V331MELA40 1200 1.01 LQS2V331MELB30 25 × 45 30 × 35 1300 1.10 LQS2V391MELA45 1300 1.10 LQS2V391MELB35 25 × 50 30 × 40 1400 1.21 LQS2V471MELA50 1400 1.21 LQS2V471MELB40 35 × 30 30 × 45 1400 1.21 LQS2V471MELC30 1500 1.32 LQS2V561MELB45 35 × 35 30 × 50 1500 1.32 LQS2V561MELC35 1700 1.46 LQS2V681MELB50 35 × 40 35 × 45 1700 1900 1.46 1.60 LQS2V681MELC40 LQS2V821MELC45 120 150 270 330 390 470 560 680 820 Code Size φD × L(mm) Rated ripple Leakage Current (mArms) (mA) 22 × 25 22 × 30 680 0.60 LQS2G101MELZ25 730 0.65 LQS2G121MELZ30 22 × 35 22 × 35 850 0.73 LQS2G151MELZ35 950 0.80 LQS2G181MELZ35 25 × 30 30 × 25 950 0.80 LQS2G181MELA30 950 0.80 LQS2G181MELB25 22 × 45 25 × 35 1100 0.88 LQS2G221MELZ45 1100 0.88 LQS2G221MELA35 30 × 25 22 × 50 1100 0.88 LQS2G221MELB25 1220 0.98 LQS2G271MELZ50 25 × 40 30 × 30 1220 0.98 LQS2G271MELA40 1220 0.98 LQS2G271MELB30 35 × 25 25 × 45 1220 0.98 LQS2G271MELC25 1440 1.08 LQS2G331MELA45 30 × 35 25 × 50 1440 1.08 LQS2G331MELB35 1550 1.18 LQS2G391MELA50 30 × 40 35 × 30 1550 1.18 LQS2G391MELB40 1550 1.18 LQS2G391MELC30 470 30 × 45 35 × 35 1680 1.30 LQS2G471MELB45 1680 1.30 LQS2G471MELC35 560 30 × 50 35 × 40 1900 1.41 LQS2G561MELB50 1900 1.41 LQS2G561MELC40 680 35 × 45 2120 1.56 LQS2G681MELC45 Cap. (µF) Size φD × L(mm) 180 220 270 330 390 420V (W6) Cap. (µF) Size φD × L(mm) 450V (2W) Rated ripple Leakage Current (mArms) (mA) Code 100 22 × 25 660 0.61 LQSW6101MELZ25 120 22 × 30 25 × 25 810 0.67 LQSW6121MELZ30 810 0.67 LQSW6121MELA25 150 22 × 35 25 × 30 840 0.75 LQSW6151MELZ35 840 0.75 LQSW6151MELA30 22 × 40 25 × 30 910 0.82 LQSW6181MELZ40 910 0.82 LQSW6181MELA30 180 30 × 25 22 × 45 82 640 100 22 × 30 25 × 25 690 0.63 LQS2W101MELZ30 690 0.63 LQS2W101MELA25 120 22 × 35 25 × 30 720 0.69 LQS2W121MELZ35 720 0.69 LQS2W121MELA30 22 × 40 25 × 30 790 0.77 LQS2W151MELZ40 790 0.77 LQS2W151MELA30 30 × 25 22 × 45 790 0.77 LQS2W151MELB25 870 0.85 LQS2W181MELZ45 25 × 35 30 × 30 870 0.85 LQS2W181MELA35 870 0.85 LQS2W181MELB30 25 × 40 30 × 30 1050 0.94 LQS2W221MELA40 1050 0.94 LQS2W221MELB30 35 × 25 25 × 50 1050 0.94 LQS2W221MELC25 1230 1.04 LQS2W271MELA50 30 × 35 35 × 30 1230 1.04 LQS2W271MELB35 1230 1.04 LQS2W271MELC30 330 30 × 40 35 × 35 1380 1.15 LQS2W331MELB40 1380 1.15 LQS2W331MELC35 390 30 × 50 35 × 40 1610 1.25 LQS2W391MELB50 1610 1.25 LQS2W391MELC40 35 × 45 35 × 50 1780 1.37 LQS2W471MELC45 1990 1.50 LQS2W561MELC50 150 LQSW6181MELB25 0.91 LQSW6221MELZ45 25 × 35 30 × 30 1050 0.91 LQSW6221MELA35 1050 0.91 LQSW6221MELB30 25 × 40 30 × 30 1250 1.01 LQSW6271MELA40 1250 1.01 LQSW6271MELB30 35 × 25 25 × 50 1250 1.01 LQSW6271MELC25 1420 1.11 LQSW6331MELA50 30 × 35 35 × 30 1420 1.11 LQSW6331MELB35 1420 1.11 LQSW6331MELC30 390 30 × 40 35 × 35 1610 1.21 LQSW6391MELB40 1610 1.21 LQSW6391MELC35 470 30 × 45 35 × 40 1860 1.33 LQSW6471MELB45 1860 1.33 LQSW6471MELC40 35 × 45 35 × 50 2100 1.45 LQSW6561MELC45 470 2200 1.60 LQSW6681MELC50 560 560 680 Code (mA) 0.57 0.82 330 Leakage Current 22 × 25 910 270 Rated ripple (mArms) 1050 220 Code 180 220 270 LQS2W820MELZ25 Rated ripple current (mArms) at 105°C 120Hz Frequency coefficient of rated ripple current Frequency (Hz) Coefficient 50 0.77 60 0.82 120 1.00 300 1.16 1k 1.30 10k 1.41 50k or more 1.43 CAT.8100K