0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
PLE0E102MDO1

PLE0E102MDO1

  • 厂商:

    NICHICON(尼吉康)

  • 封装:

    DIP

  • 描述:

    铝聚合物电容器 DIP 1mF ±20% 2.5V Ф10.00mm 5mΩ

  • 数据手册
  • 价格&库存
PLE0E102MDO1 数据手册
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS LE Ultra Low ESR series Ultra Low ESR, High ripple current. Load life of 2000 hours at 105°C. Radial lead type : Lead free flow soldering condition correspondence Adapted to the RoHS directive (2002/95/EC). LE Low ESR LF Specifications Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance tan δ ESR ( 1) Leakage Current ( 2) –55 ~ +105°C 2.5 ~ 6.3V 470 ~ 1500µF ± 20% at 120Hz, 20°C Not more than value of Standard ratings Not more than value of Standard ratings Not more than value of Standard ratings. 1.25 1.25 Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of initial value ( 3) 150% or less of the initial specified value 150% or less of the initial specified value Initial specified value or less (100kHz) at 120Hz, 20°C at 100kHz, 20°C After 2 minute's application of rated voltage. 20°C Performance Characteristics Characteristics of Temperature Z+105°C / Z+20°C Impedance Ratio Z - 55 ° C / Z + 20 ° C After 2000 hours' application of rated voltage Endurance at 105°C, capacitors meet the specified value for life characteristics listed at right. After 1000 hours' application of rated voltage Damp Heat at 60°C 90%RH, capacitors meet the specified value for life characteristics listed at right. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of initial value ( 3) 150% or less of the initial specified value 150% or less of the initial specified value Initial specified value or less Resistance to Soldering Heat To comply with recommended conditions for reflow soldering. Pre-heating shall be done at 150 ~ 200°C and for 60 ~ 180 sec. Peak temp. is 265°C, within 10 sec. Measurement for solder temperature profile shall be made at a point on the terminal nearest where the terminals protrude through the soldering side of PC board. Navy blue print on the case top. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 10% of initial value ( 3) 130% or less of the initial specified value 130% or less of the initial specified value Initial specified value or less Marking ( 1) ESR measurements should be made at a point on the terminal nearest the end seal of the capacitor. ( 2) Conditioning : If there is doubt about the measured result, measurement should be made again after the rated voltage is applied for 120 minutes at the temperature of 105°C. ( 3) Initial value : The value before test of examination of resistance to soldering. CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS LE series Dimensions Capacitance Lot. No. Laminated Case Silvered lead Wire Type numbering system (Example : 4V 680µF) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PLE 0G 6 8 1 MDO 1 TD φ D+0.5 MAX P ± 0.5 LE 680 g 681 Secondary code Size code Configuration Capacitance tolerance (± 20%) φd Series Voltage (g:4V) L+0.5MAX 15MIN 4MIN Rated Capacitance (680µF) Rated voltage (4V) Voltage V Code 2.5 e 4 g 6.3 j Configuration (mm) Series name Type Size φD L P φd φ 8 × 9L 8.0 8.5 3.5 0.6 φ 8 × 12L 8.0 11.5 3.5 0.6 φ 10 × 13L 10.0 12.5 5.0 0.6 φD × L 8×9 8 × 12 10 × 13 Code CO DO DO Standard ratings Rated Voltage (V) Rated Capacitance (µF) Case Size φD × L (mm) tan δ Leakage Current (µA) ESR (mΩ) (20˚C / 100kHz) Rated ripple (mArms) (105˚C / 100kHz) Code 560 820 2.5 820 1000 1500 560 4 680 820 1200 470 6.3 680 820 8×9 8×9 8 × 12 10 × 13 10 × 13 8×9 8 × 12 10 × 13 10 × 13 8 × 12 10 × 13 10 × 13 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 0.08 280 410 410 500 750 448 544 656 960 592 857 1033 5 5 5 5 5 5 5 5 5 5 5 5 6000 6300 6600 7100 7300 6000 6500 7000 7200 6400 6700 6800 PLE0E561MCO1 PLE0E821MCO6 PLE0E821MDO1 PLE0E102MDO1 PLE0E152MDO1 PLE0G561MCO1 PLE0G681MDO1 PLE0G821MDO1 PLE0G122MDO1 PLE0J471MDO1 PLE0J681MDO1 PLE0J821MDO1 : In this case, 6 will be put at 12th digit of type numbering system. Design, Specifications are subject to change without notice. Printed in Japan T.2006.I.1C
PLE0E102MDO1 价格&库存

很抱歉,暂时无法提供与“PLE0E102MDO1”相匹配的价格&库存,您可以联系我们找货

免费人工找货