PLX1V560MDL1TD

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PLX Radial Lead Type, Long Life Assurance High reliability, High voltage (to 50V). Low ESR, High ripple current. Long life of 3000 hours at 125°C. Radial lead type: Lead free flow soldering condition correspondence. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. PLX Higher Temperature PLV Specifications Item Performance Characteristics Category Temperature Range – 55 to +125°C Rated Voltage Range 16 to 50V Rated Capacitance Range 22 to 390µF Capacitance Tolerance ± 20% at 120Hz, 20°C Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C ESR ( 1) Less than or equal to the specified value at 100kHz, 20°C Leakage Current ( 2) Less than or equal to the specified value. 1.25 1.25 After 2 minutes' application of rated voltage at 20°C (100kHz) Temperature Characteristics (Max.Impedance Ratio) Z+125°C / Z+20°C Z– 55°C / Z+20°C Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 3000 hours at 125°C. Damp Heat (Steady State) The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 60°C, 90% RH. Resistance to Soldering Heat After soldering the capacitor under the soldering conditions prescribed here as preheat at 150 to 200°C for 60 to 180 seconds and peak temperature at 265°C for 10 seconds or less, the capacitor shall meet the specifications listed at right, provided that its temperature profile is measured at both of terminal ends facing the soldering side. Marking Navy blue print on the case top Capacitance change tan δ Within ± 20% of initial value ( 3) 150% or less of the initial specified value 150% or less of the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Within ± 20% of initial value ( 3) 150% or less of the initial specified value 150% or less of the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value ESR ( 1) Leakage current ( 2) ESR ( 1) Leakage current ( 2) ESR ( 1) Leakage current ( 2) 1 ESR should be measured at both of the terminal ends closest to the capacitor body. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. 3 Initial value : The value before test of examination of resistance to soldering. Dimensions Type numbering system (Example : 35V 39µF) Resin coated Case Capacitance 1 2 3 4 5 6 7 8 9 10 11 12 P L X 1 V 3 9 0 M C L 1 Size code P±0.5 φD±0.5 LX 39 V 023 Voltage(V:35V) Configuration Capacitance tolerance (±20%) φd Series Lot. No. L+0.5MAX. 15MIN Rated capacitance (39µF) Rated voltage (35V) 4MIN Series name Type Size φD L P φd φ8 × 9L 8.0 8.5 3.5 0.6 (mm) φ8 × 12L φ10 × 13L 10.0 8.0 12.5 11.5 5.0 3.5 0.6 0.6 Voltage V 16 20 25 35 50 Code C D E V H Frequency coefficient of rated ripple current 0 Frequency0/ 120Hz Coefficient 0.05 1kHz 0.30 10kHz 100kHz or more 0.70 1.00 Please refer to the Guidelines for Aluminum Electrolytic Capacitors for end seal configuration information. Dimension table in next page. CAT.8100K CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PLX Dimensions Rated Voltage (V)(code) Surge Voltage (V) 16 (1C) 18.4 20 (1D) 25 (1E) 35 (1V) 50 (1H) 23.0 28.7 40.2 57.5 Rated Ripple (mArms / 100kHz) Case Size φD × L (mm) tan δ Leakage Current (µA) at 20°C after 2 minutes 150 8×9 0.12 480 26 2100 810 PLX1C151MCL1 220 8 × 12 0.12 704 25 2400 930 PLX1C221MDL1 390 10 × 13 0.12 1248 23 2900 1130 PLX1C391MDL1 120 8×9 0.12 480 27 2000 800 PLX1D121MCL1 150 8 × 12 0.12 600 26 2300 910 PLX1D151MDL1 270 10 × 13 0.12 1080 24 2800 1110 PLX1D271MDL1 82 8×9 0.12 410 28 2000 780 PLX1E820MCL1 120 8 × 12 0.12 600 27 2300 890 PLX1E121MDL1 180 10 × 13 0.12 900 25 2800 1080 PLX1E181MDL1 39 8 ×9 0.12 273 33 1800 720 PLX1V390MCL1 56 8 × 12 0.12 392 31 2100 830 PLX1V560MDL1 100 10 × 13 0.12 700 28 2700 1040 PLX1V101MDL1  22 8×9 0.12 220 35 1800 700 PLX1H220MCL1  27 8 × 12 0.12 270 33 2000 810 PLX1H270MDL1  47 10 × 13 0.12 470 29 2600 1020 PLX1H470MDL1 Rated Capacitance (µF) ( ) ESR (mΩ) (20°C / 100kHz) Part Number Ambient temperature of a capacitor For formed lead or taped product specifications and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. CAT.8100K