UBT2A101MHD1TO

ALUMINUM ELECTROLYTIC CAPACITORS UBT High Temperature Range, For +125°C Use Highly dependable reliability withstanding load life of 2000 to 10000 hours at +125°C. Suited for automobile electronics where heavy duty services are indispensable. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). UBW AEC-Q200 compliant. Please contact us for details. High Temperature UBT Specifications Higher Capacitance UBY Performance Characteristics Item Category Temperature Range –40 to +125°C (10 to 250V), –25 to +125°C (350 to 450V) Rated Voltage Range 10 to 450V Rated Capacitance Range 4.7 to 4700µF ± 20% at 120Hz, 20°C Capacitance Tolerance Rated Voltage (V) Leakage Current 10 to 100 160 to 450 After 1 minute's application of rated voltage at 20°C, leakage Leakage current current is not more than 0.03CV or 4 (µA), whichever is greater. Rated voltage (V) tan δ (MAX.) Tangent of loss angle (tan δ) 10 0.20 16 0.16 25 0.14 35 0.12 50 0.10 63 0.10 After 1 minute's application of rated voltage at 20°C, I = 0.04CV+100 (µA) or less. 80 0.08 100 0.08 160 to 250 350 to 450 120Hz, 20°C 0.20 0.24 For capacitance of more than 1000µF, add 0.02 for every increase of 1000µF. 120Hz Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio Stability at Low Temperature (MAX.) Z– 40°C / Z+20°C 16 2 4 10 3 4 25 2 4 35 2 4 The specifications listed below shall be met when the capacitors are restored to 20°C after D.C. bias plus rated ripple current is applied at 125°C for the condition listed at right.The peak voltage shall not exceed the rated voltage. 50 2 4 tan δ Leakage current 80 2 4 φD(mm) Rated Voltage < = 50V 63 〜100V > =160V Endurance Capacitance change 63 2 4 100 2 4 160 to 250 350 to 450 3 6 6 – φ8 φ10 > = φ12.5 2000hrs. 5000hrs. 10000hrs. 2000hrs. 3000hrs. 5000hrs. 2000hrs. Within ±30% of the initial capacitance value (10 to 100V) Within ±20% of the initial capacitance value (160 to 450V) 300% or less than the initial specified value (10 to 100V) 200% or less than the initial specified value (160 to 450V) Less than or equal to the initial specified value After storing the capacitors under no load at 125˚C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. Shelf Life Printed with white color letter on blue sleeve. Marking Radial Lead Type Type numbering system (Example : 10V 220µF) 1 Sleeve (P.E.T) or Sleeve (polyolefin) 2 3 4 5 6 7 8 9 10 11 12 UB T 1 A 2 2 1 MPD 8 P±0.5 φD+ MAX. φd Pressure relief vent L + 2.0MAX. 15 MIN 4 MIN Configuration Standard type φD (mm) Pb-free leadwire Pb-free PET sleeve Semi-standard type Pb-free leadwire Pb-free Polyolefin sleeve φD 8 10 12.5 16 18 8 ,10 PD8 PD P 3.5 5.0 5.0 7.5 7.5 12.5 to 18 HD8 HD φd 0.6 0.6 0.6 0.8 0.8 0.8 0.8 1.0 1.0 1.0 Frequency coefficient of rated ripple current V Please refer to the Guidelines for Aluminum Electrolytic Capacitors for end seal configuration information. 10 to 100 V 160 to 450 Dimension table in next page. Frequency CV 1000 > CV 1000 CV Frequency 120Hz 300Hz 1kHz 10kHz or more 0.50 0.64 0.83 1.00 0.67 0.79 0.91 1.00 10kHz 100kHz or more 50Hz 120Hz 300Hz 1kHz 4.7 to 330 0.75 1.00 1.25 1.50 1.75 1.80 .47 to 150 0.80 1.00 1.15 1.30 1.40 1.50 Cap. (µF) CAT.8100K ALUMINUM ELECTROLYTIC CAPACITORS UBT Dimensions Rated Voltage （V） （code） 10 （1A） 16 （1C） 25 （1E） 35 （1V） Rated Capacitance （µF） 63 （1J） tan δ Leakage Current Impedance（Ω） Rated Ripple （µA） （mArms） MAX. at 20℃ after （20℃/100kHz） （125℃/100kHz） 1 minute （ ） Part Number 220 8× 11.5 0.20 66 0.26 340 UBT1A221MPD8 330 10× 12.5 0.20 99 0.15 620 UBT1A331MPD8 470 10× 12.5 0.20 141 0.10 680 UBT1A471MPD8 1000 10× 20 0.20 300 0.057 1100 UBT1A102MPD8 2200 12.5× 25 0.22 660 0.033 1750 UBT1A222MHD8 3300 16× 25 0.24 990 0.024 2300 UBT1A332MHD8 4700 16× 31.5 0.26 1410 0.020 2710 UBT1A472MHD8 100 8× 11.5 0.16 48 0.32 340 UBT1C101MPD8 220 10× 12.5 0.16 105.6 0.15 620 UBT1C221MPD8 330 10× 12.5 0.16 158.4 0.10 680 UBT1C331MPD8 470 10× 16 0.16 225.6 0.075 945 UBT1C471MPD8 1000 12.5× 20 0.16 480 0.042 1490 UBT1C102MHD8 2200 16× 25 0.18 1056 0.024 2300 UBT1C222MHD8 3300 16× 31.5 0.20 1584 0.020 2710 UBT1C332MHD8 4700 18× 31.5 0.22 2256 0.018 3270 UBT1C472MHD8 100 8× 11.5 0.14 75 0.13 500 UBT1E101MPD8 220 10× 12.5 0.14 165 0.10 680 UBT1E221MPD8 330 10× 16 0.14 247.5 0.075 945 UBT1E331MPD8 470 10× 20 0.14 352.5 0.057 1100 UBT1E471MPD8 1000 12.5× 25 0.14 750 0.033 1750 UBT1E102MHD8 2200 16× 31.5 0.16 1650 0.020 2710 UBT1E222MHD8 3300 18× 31.5 0.18 2475 0.017 3310 UBT1E332MHD8 100 10× 12.5 0.12 105 0.15 620 UBT1V101MPD8 220 10× 16 0.12 231 0.094 790 UBT1V221MPD8 330 10× 20 0.12 346.5 0.075 950 UBT1V331MPD8 470 12.5× 20 0.12 493.5 0.058 1330 UBT1V471MHD8 1000 16× 25 0.12 1050 0.031 2010 UBT1V102MHD8 2200 18× 35.5 0.14 2310 0.025 2790 UBT1V222MHD8 8× 11.5 0.10 1.15 85 UBT1H4R7MPD8 10 8× 11.5 0.10 15 0.75 180 UBT1H100MPD8 22 8× 11.5 0.10 33 0.50 250 UBT1H220MPD8 33 8× 11.5 0.10 49.5 0.45 300 UBT1H330MPD8 70.5 4.7 50 （1H） Case Size φD×L（mm） 7.05 47 8× 11.5 0.10 0.35 440 UBT1H470MPD8 100 10× 12.5 0.10 150 0.18 555 UBT1H101MPD8 220 10× 20 0.10 330 0.098 930 UBT1H221MPD8 330 12.5× 20 0.10 495 0.070 1330 UBT1H331MHD8 470 12.5× 25 0.10 705 0.055 1650 UBT1H471MHD8 1000 16× 31.5 0.10 1500 0.031 2430 UBT1H102MHD8 22 8× 11.5 0.10 41.58 2.00 130 UBT1J220MPD8 33 8× 11.5 0.10 62.37 1.50 150 UBT1J330MPD8 47 10× 12.5 0.10 88.83 0.59 530 UBT1J470MPD8 100 10×16 0.10 189 0.41 690 UBT1J101MPD8 220 12.5× 20 0.10 415.8 0.16 1050 UBT1J221MHD8 330 12.5× 25 0.10 623.7 0.12 1290 UBT1J331MHD8 470 12.5× 31.5 0.10 888.3 0.097 1460 UBT1J471MHD8 For polyolefin sleeve, please remove size code 8 from 12th digit. For cut leads, formed leads or taped parts, please add the appropriate code after the size code (12th digit ). If there is no size code in the part number, please add size code “1” and then add the appropriate code. CAT.8100K ALUMINUM ELECTROLYTIC CAPACITORS UBT Dimensions Rated Voltage （V） （code） 80 （1K） 100 （2A） Rated Voltage （V） （code） 160 （2C） 200 （2D） 250 （2E） 350 （2V） 400 （2G） 450 （2W） Rated Capacitance （µF） Leakage Current Impedance（Ω） Rated Ripple （µA） （mArms） MAX. at 20℃ after （20℃/100kHz） （125℃/100kHz） 1 minute Case Size φD×L（mm） tan δ 22 8× 11.5 0.08 52.8 1.50 150 UBT1K220MPD8 33 10× 12.5 0.08 79.2 0.80 480 UBT1K330MPD8 47 10× 12.5 0.08 112.8 0.80 480 UBT1K470MPD8 0.08 0.08 240 528 0.39 0.18 790 1240 UBT1K101MPD8 UBT1K221MHD8 （ ） Part Number 100 220 10× 20 12.5× 25 330 12.5× 31.5 0.08 792 0.16 1390 UBT1K331MHD8 470 16× 25 0.08 1128 0.11 1500 UBT1K471MHD8 10 8× 11.5 0.08 30 1.50 150 UBT2A100MPD8 22 10× 12.5 0.08 66 0.80 480 UBT2A220MPD8 33 47 100 220 330 10× 12.5 10× 16 12.5× 20 16× 25 16× 31.5 0.08 0.08 0.08 0.08 0.08 99 141 300 660 990 0.80 0.55 0.25 0.11 0.079 480 630 990 1500 1790 UBT2A330MPD8 UBT2A470MPD8 UBT2A101MHD8 UBT2A221MHD8 UBT2A331MHD8 Rated Capacitance （µF） Leakage Current （µA） at 20℃ after 1 minute Rated Ripple （mArms） （125℃/120Hz） Part Number 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.20 0.24 0.24 0.24 0.24 0.24 0.24 0.24 240.8 311.2 400.8 535.2 740 1060 180 276 364 476 644 900 200 320 430 570 780 165.8 240 408 562 758 175.2 260 115 154 187 245 329 434 78 126 157 204 250 329 78 128 171 225 292 53 85 139 189 243 53 86 UBT2C220MPD8 UBT2C330MPD8 UBT2C470MHD8 UBT2C680MHD8 UBT2C101MHD8 UBT2C151MHD8 UBT2D100MPD8 UBT2D220MPD8 UBT2D330MHD8 UBT2D470MHD8 UBT2D680MHD8 UBT2D101MHD8 UBT2E100MPD8 UBT2E220MHD8 UBT2E330MHD8 UBT2E470MHD8 UBT2E680MHD8 UBT2V4R7MPD8 UBT2V100MPD8 UBT2V220MHD8 UBT2V330MHD8 UBT2V470MHD8 UBT2G4R7MPD8 UBT2G100MPD8 12.5 × 31.5 16 × 25 16 × 31.5 10 × 25 12.5 × 20 0.24 0.24 0.24 0.24 0.24 452 628 852 184.6 280 142 189 243 58 86 UBT2G220MHD8 UBT2G330MHD8 UBT2G470MHD8 UBT2W4R7MPD8 UBT2W100MHD8 16 × 25 16 × 31.5 0.24 0.24 496 694 154 203 UBT2W220MHD8 UBT2W330MHD8 Case Size φD×L（mm） tan δ 22 33 47 68 100 150 10 22 33 47 68 100 10 22 33 47 68 4.7 10 22 33 47 4.7 10 10 × 20 10 × 25 12.5 × 20 12.5 × 25 16 × 25 16 × 31.5 10 × 20 10 × 25 12.5 × 20 12.5 × 25 16 × 20 16 × 25 10 × 20 12.5 × 20 12.5 × 25 16 × 25 16 × 31.5 10 × 20 10 × 25 12.5 × 25 16 × 25 16 × 31.5 10 × 20 10 × 25 22 33 47 4.7 10 22 33 （ ） For polyolefin sleeve, please remove size code 8 from 12th digit. For cut leads, formed leads or taped parts, please add the appropriate code after the size code (12th digit ). If there is no size code in the part number, please add size code “1” and then add the appropriate code. For formed lead or taped product specifications and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. CAT.8100K