UCD1C471MNL1GS

ALUMINUM ELECTROLYTIC CAPACITORS U U U U Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 6.3 to 100V Rated Capacitance Range 1 to 3300F Capacitance Tolerance ±20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (μA), whichever is greater. Measurement frequency : 120Hz at 20°C 6.3 0.26 Rated voltage (V) tan δ (MAX.) Tangent of loss angle (tan δ) 10 0.19 16 0.16 25 0.14 35 0.12 50 0.10 63 0.08 80 0.08 100 0.07 For capacitance of more than 1000μF, add 0.02 for every increase of 1000μF. Measurement frequency : 120Hz Rated voltage (V) 6.3 10 16 25 35 50 63 80 100 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 4 4 4 3 3 3 3 3 3 Z—25°C / Z+20°C Impedance ratio Z—40°C / Z+20°C ZT / Z20 (MAX.) Z—55°C / Z+20°C Stability at Low Temperature The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 5000 hours (2000 hours for L 10 mm: 50V or less, and for L 10mm: 63V or more) at 105°C. Endurance Capacitance Change Within ± 30% of the initial capacitance value tan δ 200% or less than the initial specified value 300% or less than the initial specified value for 63V or more Leakage current Less than or equal to the initial specified value Shelf Life After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. Resistance to soldering heat The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250°C. The capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20°C. Capacitance Change Within ± 10% of the initial capacitance value tan δ Less than or equal to the initial specified value Leakage current Less than or equal to the initial specified value Black print on the case top. Marking Type numbering system (Example : 16V 100μF) (φ4 to φ8 × φ6.2) 4 5 6 7 8 9 Package code Size Package φ4 to 10 Taping φ12.5 to 18 Taping φ12.5 to 18 Tray L±1.0 Series 0.5 MAX. A B C E L H 0.5 MAX. C±0.2 φD×L A±0.2 E A±0.2 A B C E L H H Negative 4 × 5.8 5 × 5.8 6.3 × 5.8 6.3 × 7.7 8 × 6.2 8 × 10 10 × 7.7 10 × 10 NQ (mm) 3.3 3.2 1.8 2.9 2.1 3.2 2.4 2.4 8.3 10.3 4.3 8.3 5.3 10.3 6.6 6.6 8.3 10.3 4.3 8.3 5.3 10.3 6.6 6.6 4.5 2.3 1.0 3.1 1.3 4.5 2.2 2.2 10 6.2 5.8 10 7.7 5.8 5.8 7.7 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 10 × 13.5 12.5 × 13.5 16 × 16.5 18 × 16.5 6.4 5.4 3.2 4.8 10.3 19.1 17.1 13.6 19.1 17.1 10.3 13.6 6.3 4.5 6.3 4.0 16.5 13.5 16.5 13.5 0.8 to 1.1 1.0 to 1.4 1.0 to 1.4 1.0 to 1.4 Voltage φ8 × 10L, φ10 × 10L, φ12.5 × 13.5L, φ16 × 16.5L, φ18 × 16.5L : The vibration structure-resistant product is also available upon request, please ask for details. Dimension table in next page. φD Code 4 to 6.3 CL 8 (6.2L) CL 10(7.7L) CL 8 (10L) • NL 10(10L,13.5L) 12.5 to 18 φD×L Positive 0.3 MAX. φ D±0.5 330 µF CD 50V H1015 nichicon Capacitance 2 : Except : φ10 × 7.7L Voltage Pressure relief vent Type Negative Plastic platform Lot No. Series name H L±0.5 B±0.2 Trade mark Rated voltage (16V) A±0.2 E A±0.2 B±0.2 Pressure 2 relief vent Capacitance Lot No. C±0.2 0.3 MAX. φD±0.5 A2 220E CD Trade mark (φ12.5 to φ18) Rated capacitance (100μF) Positive Plastic platform Code GS MS ZD Size code Configuration Capacitance tolerance (±20%) 1: Size φ8 × 6.2 only Series 12 13 14 Negative (φ8 × 10, φ10) Voltage ( E : 25V ) 10 11 A±0.2 E A±0.2 B±0.2 φD±0.5 A2 47 j CD 3 H L±0.3 Capacitance Lot No. C±0.2 0.3 MAX. Series 2 UCD 1 C 1 0 1 M C L 1 GS 0.5 MAX. Voltage ( j : 6.3V ) 1 Trade mark 1 Positive Plastic platform 128 V 6.3 10 16 25 35 50 63 80 100 Code j A C E V H J K 2A CAT.8100F ALUMINUM ELECTROLYTIC CAPACITORS UCD Dimensions Cap. (µF) V 6.3 10 16 25 35 50 Code 0J 1A 1C 1E 1V 1H 1 010 4 × 5.8 2.70 60 2.2 2R2 4 × 5.8 2.70 60 3.3 3R3 4 × 5.8 2.70 60 4.7 4R7 60 10 15 22 27 33 47 4 × 5.8 100 150 220 270 330 4 × 5.8 4 × 5.8 5 × 5.8 1.35 90 1.35 4 × 5.8 90 0.70 1.35 1.35 90 5 × 5.8 0.70 160 5 × 5.8 0.70 160 4 × 5.8 1.35 90 5 × 5.8 0.70 160 4 × 5.8 1.35 90 4 × 5.8 1.35 90 5 × 5.8 0.70 160 5 × 5.8 0.70 160 6.3 × 5.8 6.3 × 5.8 470 0.36 90 90 160 4 × 5.8 1.35 0.36 4 × 5.8 1.35 0.70 160 6.3 × 5.8 0.36 240 5 × 5.8 0.70 160 5 × 5.8 0.70 160 6.3 × 5.8 0.36 240 5 × 5.8 0.70 160 6.3 × 5.8 0.36 240 6.3 × 5.8 240 0.36 1.35 90 4 × 5.8 2.70 4 × 5.8 1.35 90 5 × 5.8 1.50 90 5 × 5.8 0.70 160 6.3 × 5.8 0.86 170 5 × 5.8 0.70 160 6.3 × 5.8 0.86 170 6.3 × 7.7 0.66 195 6.3 × 5.8 0.36 240 8 × 6.2 0.63 200 6.3 × 7.7 0.66 195 8 × 6.2 0.63 200 90 240 5 × 5.8 4 × 5.8 240 6.3 × 5.8 0.36 240 56 560 5 × 5.8 0.70 160 6.3 × 5.8 0.36 240 6.3 × 5.8 0.36 240 6.3 × 5.8 0.36 240 68 680 6.3 × 5.8 0.36 240 6.3 × 5.8 0.36 240 6.3 × 5.8 0.36 240 6.3 × 5.8 0.36 240 6.3 × 7.7 0.32 290 5 × 5.8 0.70 160 6.3 × 7.7 0.32 290 6.3 × 7.7 0.32 290 8 × 10 0.32 350 6.3 × 5.8 0.36 240 8 × 6.2 0.26 300 8 × 10 0.16 600 10 × 7.7 0.36 330 8 × 10 0.16 600 8 × 10 0.16 600 10 × 10 0.16 700 10 × 7.7 0.18 600 10 × 7.7 0.18 600 10 × 10 0.16 700 100 150 220 330 390 470 6.3 × 5.8 101 151 221 6.3 × 5.8 6.3 × 5.8 0.36 240 0.36 6.3 × 5.8 0.36 0.36 240 240 6.3 × 5.8 6.3 × 7.7 0.36 0.32 6.3 × 7.7 0.32 290 6.3 × 7.7 0.32 290 8 × 10 0.16 600 8 × 10 0.16 600 8 × 6.2 0.26 300 8 × 6.2 0.26 300 10 × 7.7 0.18 600 10 × 7.7 0.18 600 8 × 10 0.16 600 8 × 10 0.16 600 10 × 10 0.08 850 10 × 7.7  0.18 600 6.3 × 7.7 0.32 290 8 × 10 0.16 600 8 × 6.2 0.26 300 10 × 7.7 0.18 600 331 391 8 × 10 0.16 600 8 × 10 0.16 600 10 × 7.7 0.18 600 10 × 7.7 0.18 10 × 10 0.16 600 600 10 × 7.7  0.18 600 0.08 850 10 × 10 0.08 850 8 × 10 0.16 600 0.18 600 102 8 × 10 0.16 600 10 × 10 0.08 850 10 × 13.5 0.08 1500 152 10 × 10 0.08 850 10 × 13.5 0.08 950 12.5 × 13.5 0.08 2200 222 10 × 13.5 0.08 0.08 1100 3300 332 12.5 × 13.5 0.08 V 63 80 Cap. (µF) Code 1J 1K 3.3 3R3 4.7 4R7 10 22 681 100 5 × 5.8 6.3 × 5.8 950 12.5 × 13.5 50 1.50 950 12.5 × 13.5 0.08 1100 950 12.5 × 13.5 0.08 1100 950 12.5 × 13.5 0.08 1100 0.14 800 0.12 900 12.5 × 13.5 0.12 900 16 × 16.5 0.073 1610 850 0.08 10 × 13.5 12.5 × 13.5 16 × 16.5 0.073 1610 16 × 16.5 0.035 1800 1100 16 × 16.5 0.035 1800 Case size Rated Impedance φD × L ripple (mm) 100 2A 5 × 5.8 5.00 25 6.3 × 5.8 3.00 40 6.3 × 7.7 2.40 60 8 × 6.2 2.40 60 8 × 10 1.30 130 80 6.3 × 7.7 1.20 120 8 × 6.2 1.20 120 220 8 × 10 1.30 130 33 330 8 × 10 0.65 250 8 × 10 1.30 130 10 × 10 0.70 200 47 470 8 × 10 0.65 250 10 × 10 0.70 200 12.5 × 13.5 0.32 500 68 680 10 × 10 0.35 400 12.5 × 13.5 0.32 500 12.5 × 13.5 0.32 500 100 101 10 × 10 0.35 400 12.5 × 13.5 0.32 500 16 × 16.5 0.17 793 150 151 12.5 × 13.5 0.16 800 12.5 × 13.5 0.32 500 16 × 16.5 0.17 793 220 221 12.5 × 13.5 0.16 800 18 × 16.5 0.15 917 330 331 0.15 917 470 471 16 × 16.5 0.082 1410 680 681 18 × 16.5 0.08 0.08 10 × 13.5 1100 3.00 0.08 10 × 13.5 10 × 10 471 8 × 10 1000 290 240 10 × 7.7 680 240 16 × 16.5 0.17 793 18 × 16.5 18 × 16.5 0.15 917 Case size Rated Impedance φD × L ripple (mm) 1690 Max. Impedance ( Ω) at 20°C 100kHz, Rated ripple current (mArms) at 105°C 100kHz : In this case, 6 will be put at 12th digit of type numbering system. Frequency coefficient of rated ripple current Frequency 50Hz 120Hz 300Hz 1kHz 10kHz or more Coefficient 0.35 0.50 0.64 0.83 1.00 129 Taping specifications are given in page 23. Recommended land size, soldering by refrow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100F