UCH1V101MCL1GS

ALUMINUM ELECTROLYTIC CAPACITORS UCH Chip Type, High Reliability. Low temperature ESR specification. Added ESR specification after the test at -40°C. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. UCH UCZ Low ESR Specifications Item Performance Characteristics Category Temperature Range –40 to +125°C Rated Voltage Range 25 to 63V Rated Capacitance Range 33 to 560µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01CV (µA). Rated voltage (V) tan δ (max.) Tangent of loss angle (tan δ) Stability at Low Temperature 25 0.18 35 0.16 50 0.16 Measurement frequency : 120Hz at 20°C 63 0.14 Rated voltage (V) 25 35 50 63 Impedance ratio Z(–40°C) / Z(+20°C) ZT / Z20 (max.) 3 3 3 3 Capacitance change tan δ Leakage current The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 125°C. Endurance Measurement frequency : 120Hz Within ±30% of the initial capacitance value 300% or less than the initial specified value Less than or equal to the initial specified value After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, Within ±10% of the initial capacitance value Capacitance change which is maintained at 250°C. The capacitors shall meet Less than or equal to the initial specified value tan δ the characteristic requirements listed at right when they Less than or equal to the initial specified value Leakage current are removed from the plate and restored to 20°C. Shelf Life Resistance to soldering heat Black print on the case top. Marking ※ I : Leakage Current (μA), C : Rated Capacitance (μF), V : Rated Voltage (V) Chip Type Type numbering system (Example : 35V 47µF) (φ6.3 )【Standard】 1 Positive Capacitance tolerance (±20%) Rated capacitance (47µF) Rated voltage (35V) Negative Size Code Standard L Vibration Resistance S Series name Type (φ8, φ10 )【Vibration Resistance】 Trade mark Positive Voltage (V:35V) Plastic platform Series Capacitance C±0.2 0.3 max. B±0.2 A2 220V  CH A±0.2 E A±0.2 B±0.2 φD±0.5 9 10 11 12 13 14 Configuration Lot No. H L± 0.5 Capacitance 8 φD±0.5 C±0.2 0.3max. A2 220V CH Lot No. Positive Plastic platform Series 7 Negative 0.5max. Voltage (V:35V) 6 Taping code (φ8, φ10 )【Standard】 Trade mark 5 A±0.2 E A±0.2 B±0.2 φD±0.5 A2 47V CH Lot No. 4 H L± 0.3 Capacitance 3 L ± 1.0 0.5max. C±0.2 0.3max. 2 UCH 1 V 4 7 0 MC L 1 GS A±0.2 E A±0.2 Plastic platform Series 0.5max. Voltage (V:35V) H Negative Aid electrode (φ6.3 )【Vibration Resistance】 Trade mark φD±0.5 B±0.2 H L ± 1.0 Capacitance 0.5max. C±0.2 0.3 max. A±0.2 E A±0.2 Voltage (V:35V) Plastic platform Series A2 100V  CH Lot No. Positive Negative (mm) Vibration Resistance (mm) Standard Voltage φD×L φD×L V 25 35 50 63 6.3×7.7 8×10 10×10 6.3×7.7 8×10 10×10 2.4 2.9 3.2 2.4 2.9 3.2 A A Code E V H J 6.6 8.3 10.3 6.6 8.3 10.3 B B 6.6 8.3 10.3 6.6 8.3 10.3 C C 2.2 3.1 4.5 2.2 3.1 4.5 E E 7.7 10 10 7.7 10 10 L L H 0.5 to 0.8 0.8 to 1.1 0.8 to 11 H 0.5 to 0.8 1.1 to 1.5 1.1 to 1.5 Frequency coefficient of rated ripple current 0 Frequency0/ Coefficient 50Hz 0.35 120Hz­ 0.50 300Hz 0.64 1kHz 0.83 10kHz or more 1.00 Dimension table in next page. CAT.8100L ALUMINUM  ELECTROLYTIC  CAPACITORS UCH ■ Dimensions Rated Voltage （V） （code） 25 （1E） 35 （1V） 50 （1H） 63 （1J） Rated Capacitance （µF） Case Size φD×L（mm） tan δ Leakage Current （µA） at 20℃ after 2 minutes （ ） ESR（Ω）max. Initial 20℃ 100kHz Initial －40℃ 100kHz Rated Ripple after （mArms） endurance test 2000hours （125℃/100kHz） －40℃ 400kHz Part Number 150 6.3× 7.7 0.18 37.5 0.30 3.0 6.0 197 UCH1E151MC□1GS 330 8× 10 0.18 82.5 0.20 2.0 4.5 270 UCH1E331MC□1GS 560 10× 10 0.18 47 6.3× 7.7 0.16 140 0.15 1.5 3.5 500 UCH1E561MC□1GS 16.45 0.30 3.0 6.0 197 UCH1V470MC□1GS 100 6.3× 7.7 0.16 35 0.30 3.0 6.0 197 UCH1V101MC□1GS 220 8× 10 0.16 77 0.20 2.0 4.5 270 UCH1V221MC□1GS 330 10× 10 0.16 115.5 0.15 1.5 3.5 500 UCH1V331MC□1GS 47 6.3× 7.7 0.16 23.5 0.80 8.0 － 150 UCH1H470MC□1GS 100 8× 10 0.16 50 0.40 6.0 － 250 UCH1H101MC□1GS 220 10× 10 0.16 110 0.25 3.0 － 400 UCH1H221MC□1GS 33 6.3× 7.7 0.14 20.79 0.80 8.0 － 150 UCH1J330MC□1GS 68 8× 10 0.14 42.84 0.40 6.0 － 250 UCH1J680MC□1GS 100 10× 10 0.14 63 0.25 3.0 － 400 UCH1J101MC□1GS □ : Enter the appropriate configuration code. For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. CAT.8100L