UCL0J331MCL6GS

ALUMINUM  ELECTROLYTIC  CAPACITORS U U U Smaller Higher capacitance UCM Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 10 to 2200µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltages at 20°C, leakage current is not more than 0.01 CV or 3 (µA), whichever is greater. Measurement frequency : 120Hz at 20°C Tangent of loss angle (tan δ) Rated voltage (V) tan δ (max.) 6.3 0.26 10 0.19 16 0.16 25 0.14 Rated voltage (V) 6.3 10 16 25 35 50 Z(—25°C) / Z(+20°C) 2 2 2 2 2 2 Z(—40°C) / Z(+20°C) 3 3 3 3 3 3 Z(—55°C) / Z(+20°C) 4 4 4 3 3 3 35 0.12 50 0.10 Measurement frequency : 120Hz Stability at Low Temperature Impedance ratio ZT / Z20 (max.) The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 105°C. Endurance Capacitance Change Within ± 30% of the initial capacitance value tan δ 200% or less than the initial specified value Leakage current Less than or equal to the initial specified value Shelf Life After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. Resistance to soldering heat The capacitors are kept on a hot plate for 30 seconds, which is maintained at 250°C. The capacitors shall meet the characteristic requirements listed at right when they are removed from the plate and restored to 20°C . Marking Black print on the case top. Capacitance Change Within ± 10% of the initial capacitance value tan δ Less than or equal to the initial specified value Leakage current Less than or equal to the initial specified value ※ I : Leakage Current (μA), C : Rated Capacitance (μF), V : Rated Voltage (V) Type numbering system (Example : 16V 100µF) Chip Type (φ4 to φ8 × 6.2) Positive Lot No. C±0.2 B±0.2 φD±0.5 0.3 max. 3 4 5 6 7 8 9 10 11 12 13 14 Size code Capacitance tolerance (±20%) Negative Series name NL H L±0.5 2 : Except : φ10 × 7.7L 0.5 max. (mm) φD×L A±0.2 E A±0.2 B±0.2 Pressure 2 relief vent Capacitance Lot No. C±0.2 0.3 max. φD±0.5 A2 220E CL Trade mark 8 (10L) • 10(10L,13.5L) Positive Plastic platform Series name Code CL CL CL Rated voltage (16V) Type (φ8 × 10, φ10) φD 4 to 6.3 8 (6.2L) 10(7.7L) Rated capacitance (100µF) 1: Size φ8 × 6.2 only Voltage (E : 25V ) Taping code Configuration H L±0.3 Capacitance 2 A±0.2 E A±0.2 Series name A2 100C CL 1 Trade mark 1 UC L 1 C 1 0 1 M C L 1 GS 0.5 max. Plastic platform Voltage (C : 16V ) Negative 4 × 5.8 5 × 5.8 8 × 6.2 8 × 10 10 × 7.7 A 1.8 2.1 2.4 2.4 3.3 2.9 3.2 3.2 3.2 10 × 10 10 × 13.5 B 4.3 5.3 6.6 6.6 8.3 8.3 10.3 10.3 10.3 C 4.3 5.3 6.6 6.6 8.3 8.3 10.3 10.3 10.3 E 1.0 1.3 2.2 2.2 2.3 3.1 4.5 4.5 4.5 L 5.8 5.8 5.8 7.7 6.2 10 7.7 10 13.5 H Voltage 6.3 × 5.8 6.3 × 7.7 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 V 6.3 10 16 25 35 50 Frequency coefficient of rated ripple current Code j A C E V H Frequency 50Hz 120Hz 300Hz 1kHz 10kHz or more Coefficient 0.35 0.50 0.64 0.83 1.00 Dimension table in next page. CAT.8100L ALUMINUM  ELECTROLYTIC  CAPACITORS UCL Dimensions Rated Voltage （V） （code） 6.3 （0J） 10 （1A） 16 （1C） Rated Capacitance （µF） Leakage Current Impedance（Ω） Rated Ripple （µA） （mArms） max. at 20℃ after （20℃/100kHz） （105℃/100kHz） 2 minutes Case Size φD×L（mm） tan δ 22 4×5.8 0.26 3 0.85 160 UCL0J220MCL1GS 47 4× 5.8 0.26 3 0.85 160 UCL0J470MCL6GS 47 5× 5.8 0.26 3 0.36 240 UCL0J470MCL1GS （ ） Part Number 100 5×5.8 0.26 6.3 0.36 240 UCL0J101MCL6GS 100 6.3× 5.8 0.26 6.3 0.26 300 UCL0J101MCL1GS 220 6.3× 5.8 0.26 13.86 0.26 300 UCL0J221MCL1GS 330 6.3× 7.7 0.26 20.79 0.16 600 UCL0J331MCL1GS 330 8×6.2 0.26 20.79 0.18 500 UCL0J331MCL6GS 470 8×10 0.26 29.61 0.08 850 UCL0J471MNL1GS 470 10× 7.7 0.26 29.61 0.10 850 UCL0J471MCL6GS UCL0J102MNL1GS 1000 8×10 0.26 63 0.08 850 1500 10 ×10 0.26 94.5 0.06 1190 UCL0J152MNL1GS 1800 10 ×10 0.26 113.4 0.08 850 UCL0J182MNL1GS 2200 10×13.5 0.26 138.6 0.06 1190 UCL0J222MNL1GS 22 4× 5.8 0.19 3 0.85 160 UCL1A220MCL1GS 33 4× 5.8 0.19 3.3 0.85 160 UCL1A330MCL6GS 33 5× 5.8 0.19 3.3 0.36 240 UCL1A330MCL1GS 4.7 47 6.3× 5.8 0.19 0.26 300 UCL1A470MCL1GS 100 6.3×5.8 0.19 10 0.26 300 UCL1A101MCL1GS 150 6.3×5.8 0.19 15 0.26 300 UCL1A151MCL1GS 220 6.3×7.7 0.19 22 0.16 600 UCL1A221MCL1GS 220 8× 6.2 0.19 22 0.18 500 UCL1A221MCL6GS 330 8×10 0.19 33 0.08 850 UCL1A331MNL1GS 330 10× 7.7 0.19 33 0.10 850 UCL1A331MCL6GS UCL1A471MNL1GS 470 8×10 0.19 47 0.08 850 470 10× 7.7 0.19 47 0.10 850 UCL1A471MCL6GS 680 8×10 0.19 68 0.08 850 UCL1A681MNL1GS 1000 10 ×10 0.19 100 0.06 1190 UCL1A102MNL1GS 1200 10 ×10 0.19 120 0.08 850 UCL1A122MNL1GS 1500 10 ×13.5 0.19 150 0.06 1190 UCL1A152MNL1GS 10 4× 5.8 0.16 3 0.85 160 UCL1C100MCL1GS 22 4× 5.8 0.16 3.52 0.85 160 UCL1C220MCL6GS 22 5× 5.8 0.16 3.52 0.36 240 UCL1C220MCL1GS 47 5× 5.8 0.16 7.52 0.36 240 UCL1C470MCL6GS 47 6.3× 5.8 0.16 7.52 0.26 300 UCL1C470MCL1GS 68 6.3× 5.8 0.16 10.88 0.26 300 UCL1C680MCL1GS 100 6.3×5.8 0.16 16 0.26 300 UCL1C101MCL1GS 100 6.3×7.7 0.16 16 0.16 600 UCL1C101MCL6GS 150 6.3×7.7 0.16 24 0.16 600 UCL1C151MCL1GS 220 6.3×7.7 0.16 35.2 0.16 600 UCL1C221MCL1GS 220 8× 6.2 0.16 35.2 0.18 500 UCL1C221MCL6GS UCL1C331MNL1GS 330 8×10 0.16 52.8 0.08 850 330 10 ×7.7 0.16 52.8 0.10 850 UCL1C331MCL6GS 470 8×10 0.16 75.2 0.08 850 UCL1C471MNL1GS 470 10 ×7.7 0.16 75.2 0.10 850 UCL1C471MCL6GS 680 10 ×10 0.16 108.8 0.06 1190 UCL1C681MNL1GS 820 10 ×10 0.16 131.2 0.08 850 UCL1C821MNL1GS 10 ×13.5 0.16 160 0.06 1190 UCL1C102MNL1GS 1000 CAT.8100L ALUMINUM  ELECTROLYTIC  CAPACITORS UCL Dimensions Rated Voltage （V） （code） 25 （1E） 35 （1V） 50 （1H） Leakage Current Impedance（Ω） Rated Ripple （µA） （mArms） max. at 20℃ after （20℃/100kHz） （105℃/100kHz） 2 minutes Rated Capacitance （µF） Case Size φD×L（mm） tan δ 10 4× 5.8 0.14 3 0.85 160 UCL1E100MCL1GS 22 5× 5.8 0.14 5.5 0.36 240 UCL1E220MCL1GS 33 5× 5.8 0.14 8.25 0.36 240 UCL1E330MCL6GS 33 6.3× 5.8 0.14 8.25 0.26 300 UCL1E330MCL1GS 47 6.3× 5.8 0.14 11.75 0.26 300 UCL1E470MCL1GS 68 6.3× 5.8 0.14 17 0.26 300 UCL1E680MCL1GS （ ） Part Number 100 6.3× 7.7 0.14 25 0.16 600 UCL1E101MCL1GS 100 8× 6.2 0.14 25 0.18 500 UCL1E101MCL6GS 150 8×10 0.14 37.5 0.08 850 UCL1E151MNL1GS UCL1E151MCL6GS 150 10× 7.7 0.14 37.5 0.10 850 220 8× 10 0.14 55 0.08 850 UCL1E221MNL1GS 220 10× 7.7 0.14 55 0.10 850 UCL1E221MCL6GS 330 8× 10 0.14 82.5 0.08 850 UCL1E331MNL1GS 470 10× 10 0.14 117.5 0.06 1190 UCL1E471MNL1GS 560 10× 10 0.14 140 0.08 850 UCL1E561MNL1GS 680 10× 13.5 0.14 170 0.06 1190 UCL1E681MNL1GS 10 4× 5.8 0.12 3.5 0.85 160 UCL1V100MCL6GS 10 5× 5.8 0.12 3.5 0.36 240 UCL1V100MCL1GS 22 5× 5.8 0.12 7.7 0.36 240 UCL1V220MCL1GS 33 6.3× 5.8 0.12 11.55 0.26 300 UCL1V330MCL1GS 47 6.3× 5.8 0.12 16.45 0.26 300 UCL1V470MCL1GS 68 6.3× 7.7 0.12 23.8 0.16 600 UCL1V680MCL1GS 100 6.3× 7.7 0.12 35 0.16 600 UCL1V101MCL6GS 100 8× 10 0.12 35 0.08 850 UCL1V101MNL1GS 150 8× 10 0.12 52.5 0.08 850 UCL1V151MNL1GS 150 10× 7.7 0.12 52.5 0.10 850 UCL1V151MCL6GS 220 8× 10 0.12 77 0.08 850 UCL1V221MNL1GS 220 10× 7.7 0.12 77 0.10 850 UCL1V221MCL6GS 330 10× 10 0.12 115.5 0.06 1190 UCL1V331MNL1GS 390 10× 10 0.12 136.5 0.08 850 UCL1V391MNL1GS 470 10× 13.5 0.12 164.5 0.06 1190 UCL1V471MNL1GS 100 8× 10 0.10 50 0.18 670 UCL1H101MNL1GS 220 10× 10 0.10 110 0.12 900 UCL1H221MNL1GS For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. CAT.8100L