UCM1V470MCL1GS

ALUMINUM  ELECTROLYTIC  CAPACITORS UCM Chip Type, Low Impedance Chip type, low impedance temperature range up to +105°C. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. UCL UCD Smaller Higher capacitance UCM Smaller Higher capacitance ■Specifications Specifications UCV Item Item PerformancePerformance Characteristics Characteristics – 55 to +105C –55 to +105°C 6.36.3 to 50V to 100V 10 to 2200 F 10 to 5100µF 20% at 120Hz, 20C ± 20% at 120Hz, 20°C of rated voltage, leakage current is not more than 0.01CV After 2 minute's application After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater. Measurement frequency : 120Hz, Category Temperature TemperatureRange Range Category Rated Voltage Range Range Rated Voltage Rated Capacitance Range Rated Capacitance Range Capacitance Tolerance Capacitance Tolerance Leakage Current Leakage Current Rated voltage (V) Tangent of loss angle (tan δ) tan (MAX.) 6.3 10 16 25 35 50 0.26 0.19 0.16 0.14 0.12 0.10 Measurement : 120Hz at 20°C C Temperature : 20frequency 63 80 100 Measurement0.08 frequency : 120 Hz 0.08 0.07 Rated voltage (V) 6.3 10 16 25 35 50 0.26 0.19 0.16 0.14 0.10 50 tan Rated δ (max.) voltage (V) 6.3 10 16 25 0.12 35 For capacitance of more than 1000µF, add 2 0.02 for every 2 increase 2 of 1000µF.( 2 φ12.5 to2 φ18 ) 2 Tangent of loss angle (tan δ) Z–25C / Z+20C Z–40C / Z+20C Rated voltage Z–55C /(V) Z+20C Stability at Low Temperature Impedance ratio ZT / Z20 (MAX.) 3 4 6.3 3 410 3 416 3 Measurement frequency : 120Hz 3 3 100 80 353 25 63 50 3 3 Z(– 25°C) / Z(+20°C) 2 2 2 2 2 2 2 2 2 Stability at Low Temperature Impedance ratio Capacitance Change Within 30% of the initial capacitance value Z(– 40°C) / Z(+20°C) 3 3 3 3 3 3 3 3 3 ZT / Z20 (max.) tan δ 200% or less than the initial specified value Endurance Z(– 55°C) / Z(+20°C) 3 3 3 3 4 3 4 4 3 Leakage current Less than or equal to the initial specified value Capacitance change Within ±30% of thebased initial capacitance valueclause The specifications listed at right shallatbe metfor 1000 hours After storing the capacitors under no load 105C and then performing voltage treatment on JIS C 5101-4 Shelf Life 200% or less than the initial specified value the capacitors are 20°C for after 4.1 when at 20C, they shall meet therestored specifiedtovalues thethe endurance tan δcharacteristics listed above. Endurance (For 63V or more : 300% or less than the initial specified value) rated voltage is applied for 5000 hours (2000 Capacitance Change Within the specified initial capacitance value Less than or equal 10% to theofinitial value Leakage current hours for φD 10) at 105°C. Resistance to tan δ Less than or equal to the initial specified value soldering heat After storing the capacitors under no load at 105°C for 1000 hoursLeakage and then performingLess voltage onspecified JIS C 5101-4 current thantreatment or equal tobased the initial value Shelf Life clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within ±10% of the initial capacitance value maintained at 250°C. The capacitors shall meet the characteristic Less than or equal to the initial specified value tan δ requirements listed at right when they are removed from the plate Less than or equal to the initial specified value Leakage current and restored to 20°C. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Marking Black print on the case top. Black print on the case top. Marking 0.5MAX. Series C 0.2 0.3MAX. 0.3 0.3Lmax. 0.3 L max. 0.5 A 0.2 E Code CL 8 · 10 NL Type φD¥L Negative H Pressure relief vent φD 4 to 6.3 Series name A 0.2 Capacitance 0.5max. Lot No. B 0.2 a2 470E CM φD 0.5 Series (φ8,φ10 ) Rated voltage (16V) 0.5MAX. C 0.2 0.3MAX. Configuration Rated capacitance (100F) Positive Plastic platform Trade mark Configuration Capacitance tolerance (20%) Negative H Voltage( E : 25V ) Taping code Sizeµ code Type numbering system (Example : 25V 1500 F) A 0.2 0.5max. Capacitance Lot No. ※ I : Leakage Current (μA), C : Rated Capacitance (μF), V : Rated Voltage (V) E B 0.2 φD 0.5 a2 100C CM Chip Type (φ4 to φ6.3) U CM 1 C 1 0 1 M C L 1 GS Positive Plastic platform Voltage( C : 16V ) A 0.2 Resistance to soldering heat (mm) µ 4 ¥ 5.8 5 ¥ 5.8 6.3 ¥ 5.8 6.3 ¥ 7.7 8 ¥ 10 10 ¥ 10 A 1.8 2.1 2.4 2.4 2.9 3.2 B 4.3 5.3 6.6 6.6 8.3 10.3 C 4.3 5.3 6.6 6.6 8.3 10.3 E 1.0 1.3 2.2 2.2 3.1 4.5 L 5.8 5.8 5.8 7.7 10 10 H 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 4 × 5.8 5 × 5.8 6.3 × 5.8 6.3 × 7.7 8 × 10 10 × 10 12.5 × 13.5 12.5 × 21 16 × 16.5 16 × 21.5 18 × 16.5 18 × 21.5 Voltage 35 V Plastic platform 50 H Positive C±0.2 φ D±0.5 Lot No. L±1.0 Series Dimension table in next page. 2.1 2.4 2.4 2.9 3.2 5.15 5.15 5.65 5.65 6.65 6.65 4.3 5.3 6.6 6.6 8.3 10.3 13.6 13.6 17.1 17.1 19.1 19.1 4.3 5.3 6.6 6.6 8.3 10.3 13.6 13.6 17.1 17.1 19.1 19.1 1 1.3 2.2 2.2 3.1 4.5 (3.3) (3.3) (5.8) (5.8) (5.8) (5.8) 5.8 5.8 5.8 7.7 10 10 13.5 21 16.5 21.5 16.5 21.5 0.5 to 0.8 0.5 to 0.8 0.5 to 5.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 1.0 to 1.4 1.0 to 1.4 1.0 to 1.4 1.0 to 1.4 1.0 to 1.4 1.0 to 1.4 A±0.2 E A±0.2 0.3 max. Pressure relief vent Capacitance 25 E 0.5max. 16 C Voltage 1500 µF CM 25V H1834 nichicon Trade mark 10 A B±0.2 6.3 V Code (φ12.5 to φ18 ) j 1.8 H Negative Voltage 6.3 V Code j 10 A 16 C 25 E 35 V 50 H 63 J 80 K 100 2A Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.35 120 Hz 0.50 300 Hz 0.64 1 kHz 0.83 10 kHz or more 1.00 CAT.8100L ALUMINUM  ELECTROLYTIC  CAPACITORS UCM Dimensions Rated Voltage （V） （code） 6.3 （0J） 10 （1A） 16 （1C） 25 （1E） 35 （1V） Rated Capacitance （µF） Leakage Current Rated Ripple Impedance（Ω） （µA） （mArms） max. at 20℃ after （20℃/100kHz） （105℃/100kHz） 2 minutes Case Size φD×L（mm） tan δ 100 4× 5.8 0.26 6.3 1.00 160 UCM0J101MCL1GS 220 5× 5.8 0.26 13.86 0.36 240 UCM0J221MCL1GS 330 6.3×5.8 0.26 20.79 0.26 300 UCM0J331MCL1GS 470 6.3×7.7 0.26 29.61 0.16 600 UCM0J471MCL1GS 680 6.3× 7.7 0.26 42.84 0.16 600 UCM0J681MCL1GS 1500 8×10 0.26 94.5 0.080 850 UCM0J152MNL1GS 2200 10× 10 0.26 138.6 0.060 1190 UCM0J222MNL1GS （ ） 6.8 Part Number 68 4×5.8 0.19 1.00 160 UCM1A680MCL1GS 150 5×5.8 0.19 15 0.36 240 UCM1A151MCL1GS 220 6.3× 5.8 0.19 22 0.26 300 UCM1A221MCL1GS 330 6.3× 7.7 0.19 33 0.16 600 UCM1A331MCL1GS 470 6.3×7.7 0.19 47 0.16 600 UCM1A471MCL1GS 1000 8× 10 0.19 100 0.080 850 UCM1A102MNL1GS 1500 10×10 0.19 150 0.060 1190 UCM1A152MNL1GS 47 4× 5.8 0.16 7.52 1.00 160 UCM1C470MCL1GS 68 5 ×5.8 0.16 10.88 0.36 240 UCM1C680MCL1GS 100 5× 5.8 0.16 16 0.36 240 UCM1C101MCL1GS 150 6.3×5.8 0.16 24 0.26 300 UCM1C151MCL1GS 220 6.3×5.8 0.16 35.2 0.26 300 UCM1C221MCL1GS 330 6.3×7.7 0.16 52.8 0.16 600 UCM1C331MCL1GS 680 8×10 0.16 108.8 0.080 850 UCM1C681MNL1GS 1000 10× 10 0.16 160 0.060 1190 UCM1C102MNL1GS 22 4× 5.8 0.14 5.5 1.00 160 UCM1E220MCL1GS 33 4× 5.8 0.14 8.25 1.00 160 UCM1E330MCL1GS 47 5× 5.8 0.14 11.75 0.36 240 UCM1E470MCL1GS 68 5× 5.8 0.14 17 0.36 240 UCM1E680MCL1GS 100 6.3×5.8 0.14 25 0.26 300 UCM1E101MCL1GS 150 6.3×7.7 0.14 37.5 0.16 600 UCM1E151MCL1GS 220 6.3× 7.7 0.14 55 0.16 600 UCM1E221MCL1GS 470 8×10 0.14 117.5 0.080 850 UCM1E471MNL1GS 820 10× 10 0.14 205 0.060 1190 UCM1E821MNL1GS 1500 12.5 ×13.5 0.14 375 0.058 1420 UCM1E152MNJ1MS 2400 12.5× 21 0.16 600 0.046 2080 UCM1E242MNJ1MS 2700 16×16.5 0.16 675 0.047 1910 UCM1E272MNJ1MS 3600 18×16.5 0.18 900 0.045 2060 UCM1E362MNJ1MS 3900 16×21.5 0.18 975 0.034 2540 UCM1E392MNJ1MS 5100 18×21.5 0.22 1275 0.032 2640 22 4 ×5.8 0.12 7.7 1.00 160 UCM1V220MCL1GS 33 5×5.8 0.12 11.55 0.36 240 UCM1V330MCL1GS 47 5×5.8 0.12 16.45 0.36 240 UCM1V470MCL1GS 68 6.3× 5.8 0.12 23.8 0.26 300 UCM1V680MCL1GS 100 6.3×5.8 0.12 35 0.26 300 UCM1V101MCL1GS 150 6.3× 7.7 0.12 52.5 0.16 600 UCM1V151MCL1GS 330 8× 10 0.12 115.5 0.080 850 UCM1V331MNL1GS 560 10× 10 0.12 196 0.060 1190 UCM1V561MNL1GS 910 12.5× 13.5 0.12 318.5 0.058 1420 UCM1V911MNJ1MS 12.5× 21 0.12 560 0.046 2080 UCM1V162MNJ1MS 1600 UCM1E512MNJ1MS 1800 16× 16.5 0.12 630 0.047 1910 UCM1V182MNJ1MS 2200 18× 16.5 0.14 770 0.045 2060 UCM1V222MNJ1MS 2700 16× 21.5 0.14 945 0.034 2540 UCM1V272MNJ1MS 3600 18× 21.5 0.16 1260 0.032 2640 UCM1V362MNJ1MS CAT.8100L ALUMINUM  ELECTROLYTIC  CAPACITORS UCM Dimensions Rated Voltage （V） （code） 50 （1H） 63 （1J） 80 （1K） 100 （2A） Rated Capacitance （µF） Leakage Current Impedance（Ω） Rated Ripple （µA） （mArms） max. at 20℃ after （20℃/100kHz） （105℃/100kHz） 2 minutes Case Size φD×L（mm） tan δ 10 4 ×5.8 0.10 5 2.30 85 UCM1H100MCL6GS 10 5× 5.8 0.10 5 0.88 165 UCM1H100MCL1GS 22 5× 5.8 0.10 11 0.88 165 UCM1H220MCL1GS 47 6.3× 5.8 0.10 23.5 0.68 195 UCM1H470MCL1GS 100 6.3× 7.7 0.10 50 0.34 350 UCM1H101MCL1GS 220 8× 10 0.10 110 0.18 670 UCM1H221MNL1GS 330 10× 10 0.10 165 0.12 900 UCM1H331MNL1GS 470 12.5× 13.5 0.10 235 0.12 1340 UCM1H471MNJ1MS 750 12.5× 21 0.10 375 0.080 1970 UCM1H751MNJ1MS （ ） Part Number 820 16× 16.5 0.10 410 0.080 1820 UCM1H821MNJ1MS 1100 18× 16.5 0.10 550 0.078 1980 UCM1H112MNJ1MS 1200 16× 21.5 0.10 600 0.050 2440 UCM1H122MNJ1MS 1600 18× 21.5 0.10 800 0.050 2550 UCM1H162MNJ1MS 47 6.3× 7.7 0.08 29.61 0.80 190 UCM1J470MCL1GS 100 8× 10 0.08 63 0.40 300 UCM1J101MNL1GS 220 10× 10 0.08 138.6 0.25 500 UCM1J221MNL1GS 360 12.5× 13.5 0.08 226.8 0.14 1250 UCM1J361MNJ1MS 560 12.5× 21 0.08 352.8 0.086 1850 UCM1J561MNJ1MS 620 16× 16.5 0.08 390.6 0.082 1740 UCM1J621MNJ1MS 820 18× 16.5 0.08 516.6 0.080 1880 UCM1J821MNJ1MS 910 16× 21.5 0.08 573.3 0.055 2330 UCM1J911MNJ1MS 1200 18× 21.5 0.08 756 0.054 2430 UCM1J122MNJ1MS 33 6.3× 7.7 0.08 26.4 0.80 190 UCM1K330MCL1GS 68 8× 10 0.08 54.4 0.40 300 UCM1K680MNL1GS 100 10× 10 0.08 80 0.25 500 UCM1K101MNL1GS 220 12.5× 13.5 0.08 176 0.18 1050 UCM1K221MNJ1MS 360 12.5× 21 0.08 288 0.11 1580 UCM1K361MNJ1MS 390 16× 16.5 0.08 312 0.10 1500 UCM1K391MNJ1MS 510 18× 16.5 0.08 408 0.098 1670 UCM1K511MNJ1MS 560 16× 21.5 0.08 448 0.066 2040 UCM1K561MNJ1MS 750 18× 21.5 0.08 600 0.063 2140 UCM1K751MNJ1MS 130 12.5× 13.5 0.07 130 0.18 1050 UCM2A131MNJ1MS 220 12.5× 21 0.07 220 0.11 1580 UCM2A221MNJ1MS 240 16× 16.5 0.07 240 0.10 1500 UCM2A241MNJ1MS 330 18× 16.5 0.07 330 0.098 1670 UCM2A331MNJ1MS 390 16× 21.5 0.07 390 0.066 2040 UCM2A391MNJ1MS 510 18× 21.5 0.07 510 0.063 2140 UCM2A511MNJ1MS For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. CAT.8100L