UCV1E102MNL1GS

ALUMINUM  ELECTROLYTIC  CAPACITORS UCV Chip Type, Low Impedance. Chip type, low impedance temperature range up to +105°C. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. UCM Smaller Higher capacitance UCV Specifications Item Performance Characteristics Category Temperature Range –55 to +105°C Rated Voltage Range 16 to 35V Rated Capacitance Range 220 to 1500µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01CV (µA). Rated voltage (V) tan δ (max.) Tangent of loss angle (tan δ) 16 0.16 25 0.14 16 2 3 4 Rated voltage (V) Stability at Low Temperature 35 0.12 Z(–25°C) / Z(+20°C) Impedance ratio Z(–40°C) / Z(+20°C) ZT / Z20 (max.) Z(–55°C) / Z(+20°C) 25 2 3 3 Measurement frequency : 120Hz at 20°C Measurement frequency : 120Hz 35 2 3 3 Capacitance change tan δ Leakage current The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 105°C. Endurance Within ±30% of the initial capacitance value 200% or less than the initial specified value Less than or equal to the initial specified value After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, Within ±10% of the initial capacitance value Capacitance change which is maintained at 250°C. The capacitors shall meet Less than or equal to the initial specified value tan δ the characteristic requirements listed at right when they Less than or equal to the initial specified value Leakage current are removed from the plate and restored to 20°C. Shelf Life Resistance to soldering heat Black print on the case top. Marking ※ I : Leakage Current (μA), C : Rated Capacitance (μF), V : Rated Voltage (V) Type numbering numberingsystem system (Example : 35V 220µF) Type (Example : 35V 220µF) Chip Type (φ 6.3) 1 Series C±0.2 (φ 8,φ10) Series 7 8 9 10 11 12 13 14 Taping code Configuration Capacitance tolerance (±20%) Rated capacitance (220µF) Rated voltage (35V) φD 6.3 8・10 Code CL NL Series name Type Voltage A±0.2 E A±0.2 φD±0.5 6 A±0.2 E A±0.2 H L±0.5 Capacitance 5 Positive C±0.2 0.3 max. A2 680V CV Lot No. 4 Negative Plastic platform Voltage (V : 35V ) Trade mark B±0.2 Capacitance 3 H L± 0.3 B±0.2 Lot No. φD±0.5 A2 220V CV 0.3 max. 2 UCV 1 V 2 2 1 MC L 1 GS 0.5 max. Positive Plastic platform 0.5max. Voltage (V:35V) Negative Pressure relief vent V Code Standard 16 C 25 E 35 V φD×L A B C E L H (mm) 8×10 10×10 6.3×7.7 2.9 3.2 2.4 8.3 10.3 6.6 8.3 10.3 6.6 3.1 4.5 2.2 10 10 7.7 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 Frequency coefficient of rated ripple current 0 Frequency0/ Coefficient 50Hz 0.35 120Hz­ 0.50 300Hz 0.64 1kHz 0.83 10kHz or more 1.00 Dimension table in next page. CAT.8100L ALUMINUM  ELECTROLYTIC  CAPACITORS UCV Dimensions Rated Voltage （V） （code） Rated Capacitance （µF） 470 16 （1C） 25 （1E） 35 （1V） Case Size φD×L（mm） tan δ Leakage Current Rated Ripple Impedance（Ω） （µA） （mArms） max. at 20℃ after （20℃/100kHz） （105℃/100kHz） 2 minutes （ ） 6.3× 7.7 0.16 75.2 0.16 Part Number 600 UCV1C471MCL1GS 820 8× 10 0.16 131.2 0.08 850 UCV1C821MNL1GS 1500 10× 10 0.16 240 0.06 1190 UCV1C152MNL1GS 330 6.3× 7.7 0.14 0.16 600 UCV1E331MCL1GS 82.5 560 8× 10 0.14 140 0.08 850 UCV1E561MNL1GS 1000 10× 10 0.14 250 0.06 1190 UCV1E102MNL1GS 220 6.3× 7.7 0.12 77 0.16 600 UCV1V221MCL1GS 470 8× 10 0.12 164.5 0.08 850 UCV1V471MNL1GS 680 10× 10 0.12 238 0.06 1190 UCV1V681MNL1GS For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. CAT.8100L