UCX1V222MNS1MS

ALUMINUM ELECTROLYTIC CAPACITORS UCX Chip Type, High Reliability Low temperature ESR specification Chip type, high temperature range, for +135°C use. Added ESR specification after the test at -40°C. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. UCX High Temperature UCZ Specifications ■Item Specifications Performance Characteristics –40 to +135°C 10 to 50V 47 to 3300µF ± 20% at 120Hz, 20°C Category Temperature Range Item Rated Voltage Range Performance Characteristics Category Temperature Range Rated Capacitance Range Rated VoltageTolerance Range Capacitance After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.01CV or 3(µA), whichever is greater. Leakage Current Range Rated Capacitance Measurement frequency : 120Hz at 20°C Capacitance Tolerance Rated voltage (V) 10 16 25 35 50 Tangent Current of loss angle (tan δ) 0.30 0.23 0.18 0.16 0.16 tan δ (MAX.) Leakage For capacitance of more than 1000µF, add 0.02 for every increase of 1000µF.frequency ( φ12.5 to: φ120Hz, 18) Temperature : 20 C Measurement Rated voltage (V) 10 16 25 35 Tangent of loss angle (tan δ) Measurement frequency : 120Hz 0.30(V) 0.23 10 0.18 0.16 tan (MAX.) Rated voltage 16 25 35 50 Stability at Low Temperature Impedance ratio Z–40°C / Z+20°C Rated voltage (V) (MAX.) 12 10 816 6 25 4 4 Measurement frequency : 120 Hz 35 Impedance ratio 12 8 6 / Z+20C ZTThe / Z20 (MAX.) Z–40C specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 135°C. Stability at Low Temperature 4 Within ± 30% of the initial capacitance value Capacitance Change 300% or less than the initial specified value tan δ Capacitance Change Within of thetoinitial capacitance value Less than30% or equal the initial specified value Leakage current tan δ 300% or less than the initial specified value After storing the capacitors under no load at 135°C for 1000 hoursLeakage and then performing voltage treatment based on JIS C 5101-4 Less than or equal to the initial specified value current Endurance Endurance Shelf Life clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. Resistance to soldering heat Marking After storing the capacitors under no load at 135C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause The capacitors shall be kept on the hot plate for 30 seconds, Capacitance Change 4.1 at 20C, they shall meet the specified values for the endurance characteristics listed above. Within ±10% of the initial capacitance value which is maintained at 250°C. The capacitors shall meet the Less than or equal to the initial specified value tan δ characteristic requirements listed at right when they are Capacitance Within of thetoinitial capacitance value than10% or equal the initial specified value Leakage currentChange Less removed from the plate and restored to 20°C. tan δ Less than or equal to the initial specified value Black print on the case top. Leakage current Less than or equal to the initial specified value Marking Chip Type Black print on the case top. 1 Plastic platform 7 8 1 2 3 4 5 6 A 2.9 3.2 B 8.3 10.3 Pressure C 8.3 10.3 relief vent Capacitance Series E 3.1 4.5 3.2 10.3 6.6 10.3 2.2 3.1 4.5 Negative 10.8 10 2.4 B CL 1.0 6.6 E L 10 10 L 0.8 to 1.1 0.8 to 1.1 H 8×10 0.5 to 0.8 1.1 to 1.5 10×10 Type 0.5 MAX. Positive C 0.2 φ D 0.5 A2 220V CX 0.3 MAX. C 0.2 Lot No. φ D 0.5 a2 220V CX Capacitance L 1.0 H Negative Capacitance Positive L 1.0 Plastic platform Voltage Lot No. Trade mark (mm) 2.9 A H Positive Negative 8.3 H 8.3 6.3×10 Lot No. Capacitance Series HC 0.3 MAX. φ D 0.5 φD×L Taping code 12 13 14 Plastic platform Series Trade mark 390 µF CX 50V H1015 Vibration Resistance 10×10 A 0.2 A 0.2 E H C 0.2 10 11 0.3 MAX. Series Voltage( V : 35V ) Negative L 0.5 0.3 MAX. (mm) 0.5MAX. A 0.2 E A 0.2 H Plastic platform 9 Plastic platform φ Trade mark φ nichicon 390 µF CX 50V H1015 nichicon 8×10 L 0.5 C 0.2 A 0.2 E A 0.2 Voltage Lot No. Trade mark Standard 0.3MAX. 0.5 MAX. Capacitance φD 0.5 Lot No. φD×L φD 0.5 Capacitance a2 220V CX Lot No. B 0.2 Series Trade mark Plastic platform 8 Voltage( V : 35V ) Positive B 0.2 A2 220V CX Voltage( V : 35V ) 0.5MAX. 0.3MAX. Series B 0.2 φ φD 0.5 φ Trade mark , Positive C 0.2 7 A 0.2 H Voltage( V : 35V ) 12 13 14 A 0.2 E A 0.2 A 0.2 L 1.0 Plastic platform 10 11 Code Size φ6.3 to 10 Package GScode Configuration φ12.5 to 18 MS Size code Capacitance tolerance (20%) Configuration Rated capacitance (47µF) Code ConfigurationConfiguration CL(φ10 or less) Capacitance Rated voltage tolerance (35V) (±20%) Configuration Standard NQ(φ12.5 or more) Rated capacitance CS(φ10 orCode less) Configuration Series name (47µF) Vibration Resistance NS(φ12.5 or more) Standard L Rated voltage Type (35V) Vibration Resistance S Series name Negative resistant type only Capacitance Lot φ6.3 No. × 10 : Vibration , 9 0.2 Aid electrode A 0.2 E A 0.2 H 6 0.5 MAX. L 1.0 C 0.2 5 U C X 1 V 4 7 0 M C Size L code 1 GS E Capacitance Lot No. B 0.2 B 0.2 0.3 MAX. Series φ D 0.5 φ D 0.5 a2 A2 47V 47V CX CX Voltage( V : 35V ) 4 E C 0.2 3 0.5 MAX. 0.3 MAX. Plastic platform 2 U CX 1 V 4 7 0 M C L 1 GS 0.5MAX. Series 0.5 MAX. A 0.2 E A 0.2 φ Positive A 0.2 A 0.2 φ Radial Lead Type Voltage( V : 35V ) Type numbering system (Example : 35V 47µF) B 0.2 soldering heat B 0.2 Resistance to B 0.2 Shelf Life Rated Voltage L 1.0 10 V Pressure relief vent A Code H 16 C 25 E 35 Negative V 10 1.1 to 1.5 ● Frequency coefficient of rated ripple current Frequency 50Hz 120Hz 300Hz 1kHz 10kHz or more Coefficient Dimension table in next page. 0.35 0.50 0.64 0.83 1.00 CAT.8100K ALUMINUM ELECTROLYTIC CAPACITORS UCX ■ Dimensions Leakage Current （µA） ESR（Ω）MAX. （20℃/−40℃/100kHz） Rated Ripple （mArms） after Initial Initial endurance test（135℃/100kHz） 1000hours 20℃ −40℃ −40℃ Rated Voltage （V） （code） Rated Capacitance （µF） 220 8× 10 0.30 22 0.20 3.00 12 270 UCX1A221M□□1GS 10 （1A） 330 8× 10 0.30 33 0.20 3.00 12 270 UCX1A331M□□6GS 330 10× 10 0.30 33 0.15 2.00 10 500 UCX1A331M□□1GS 470 10× 10 0.30 47 0.15 2.00 10 500 UCX1A471M□□1GS 100 6.3× 10 0.23 16 0.25 4.00 15 197 UCX1C101MCS6GS UCX1C101M□□1GS 16 （1C） 25 （1E） 35 （1V） 50 （1H） Case Size φD×L（mm） tan δ （ at 20℃ after 2 minutes ） Part Number 100 8× 10 0.23 16 0.20 3.00 12 270 220 8× 10 0.23 35.2 0.20 3.00 12 270 UCX1C221M□□1GS 330 10× 10 0.23 52.8 0.15 2.00 10 500 UCX1C331M□□1GS 470 10× 10 0.23 75.2 0.15 2.00 10 500 UCX1C471M□□1GS 100 8× 10 0.18 25 0.20 3.00 12 270 UCX1E101M□□1GS 220 10× 10 0.18 55 0.15 2.00 10 500 UCX1E221M□□1GS 330 10× 10 0.18 82.5 0.15 2.00 10 500 UCX1E331M□□1GS 820 12.5× 13.5 0.18 205 0.070 1.00 5.0 750 UCX1E821M□□1MS 1000 12.5× 13.5 0.18 250 0.070 1.00 5.0 750 UCX1E102M□□1MS 1200 16× 16.5 0.18 300 0.050 0.50 2.5 1200 UCX1E122M□□1MS 1500 16× 16.5 0.18 375 0.050 0.50 2.5 1200 UCX1E152M□□1MS 1800 16× 16.5 0.18 450 0.050 0.50 2.5 1200 UCX1E182M□□1MS 2200 18× 16.5 0.20 550 0.050 0.50 2.5 1400 UCX1E222M□□1MS 2700 16× 21.5 0.20 675 0.040 0.32 1.6 1900 UCX1E272M□□1MS 3300 18× 21.5 0.22 825 0.035 0.28 1.4 2200 UCX1E332M□□1MS 47 6.3× 10 0.16 16.45 0.25 4.00 15 197 UCX1V470MCS6GS 47 8× 10 0.16 16.45 0.20 3.00 12 270 UCX1V470M□□1GS 68 8× 10 0.16 23.8 0.20 3.00 12 270 UCX1V680M□□1GS 100 6.3× 10 0.16 35 0.25 4.00 15 197 UCX1V101MCS6GS 100 8× 10 0.16 35 0.20 3.00 12 270 UCX1V101M□□1GS 220 10× 10 0.16 77 0.15 2.00 10 500 UCX1V221M□□1GS 470 12.5× 13.5 0.16 164.5 0.070 1.00 5.0 750 UCX1V471M□□1MS 560 12.5× 13.5 0.16 196 0.070 1.00 5.0 750 UCX1V561M□□1MS 680 12.5× 13.5 0.16 238 0.070 1.00 5.0 750 UCX1V681M□□1MS 820 16× 16.5 0.16 287 0.050 0.50 2.5 1200 UCX1V821M□□1MS 1000 16×16.5 0.16 350 0.050 0.50 2.5 1200 UCX1V102M□□1MS UCX1V122M□□1MS 1200 18× 16.5 0.16 420 0.050 0.50 2.5 1400 1500 16× 21.5 0.16 525 0.040 0.32 1.6 1900 UCX1V152M□□6MS 1500 18× 16.5 0.16 525 0.050 0.50 2.5 1400 UCX1V152M□□1MS 1800 18×21.5 0.16 630 0.035 0.28 1.4 2200 UCX1V182M□□1MS 2200 18× 21.5 0.18 770 0.035 0.28 1.4 2200 UCX1V222M□□1MS 47 8× 10 0.16 23.5 0.25 3.50 15 270 UCX1H470M□□1GS 100 10 ×10 0.16 50 0.20 2.50 12 500 UCX1H101M□□1GS 390 12.5× 13.5 0.16 195 0.090 1.30 750 UCX1H391M□□1MS 6.5 470 16×16.5 0.16 235 0.070 0.70 3.5 1000 UCX1H471M□□1MS 560 16×16.5 0.16 280 0.070 0.70 3.5 1000 UCX1H561M□□1MS 680 18× 16.5 0.16 340 0.070 0.70 3.5 1200 UCX1H681M□□1MS 820 18×16.5 0.16 410 0.070 0.70 3.5 1200 UCX1H821M□□1MS 1000 16×21.5 0.16 500 0.050 0.40 2.0 1600 UCX1H102M□□1MS 1200 18×21.5 0.16 600 0.040 0.32 1.6 1900 UCX1H122M□□1MS □□ : Enter the appropriate configuration code. For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. CAT.8100K