UHC1E102MPD

ALUMINUM ELECTROLYTIC CAPACITORS HC Low Impedance series A pproved by Reliability Center for Electronic Component, Japan-Certification No. RCJ-03-23C Lower impedance than HD series. Adapted to the RoHS directive (2002/95/EC). HC Low Impedance HD Specifications ltem Category Temperature Range – 40 ~ +105˚C Rated Voltage Range 6.3 ~ 35V Performance Characteristics Rated Capacitance Range 4.7 ~ 1000µF Capacitance Tolerance Leakage Current tan δ ± 20% at 120Hz, 20˚C After 2 minutes' application of rated voltage, leakage current is less than 0.01CV or 3 (µA), whichever is greater. Rated voltage (V) tan δ (MAX.) Rated voltage (V) 6.3 0.15 6.3 2 10 0.13 10 2 16 0.12 16 2 25 0.10 25 2 35 0.10 35 2 120Hz 20˚C Stability at Low Temperature Impedance ratio ZT / Z20 (MAX.) Z–40˚C / Z+20˚C 120Hz < After an application of D.C. bias voltage plus the rated ripple current for 2000 hours (φD = 6.3 : 1000 hours ) at 105˚C the peak voltage shall not exceed the rated D.C. voltage, capacitors meet the characteristic requirements listed below. Endurance Capacitance change tan δ Leakage current Within ± 20% of initial value 200% or less of initial specified value lnitial specified value or less Marking Printed with white color letter on black sleeve. Radial Lead Type Sleeve (P.E.T.) D+0.5 MAX. fd Type numbering system (Example : 10V 470µF) UHC 1 A 4 7 1 M PD Configuration Capacitance tolerance (± 20%) Rated Capacitance (470mF) Rated voltage (10V) Series name Type Configuration Pb-free leadwire fD Pb-free PET sleeve 4 5 DD 6.3 (7L) 6.3 (11L) ED 8 á 10 PD P ± 0.5 1 2 3 4 5 6 7 8 9 10 11 Pressure relief vent 15MIN L+ MAX. (f6.3up) (No pressure relief vent for 7mmL products) f 4MIN (L = 7) 1.0 (L 11) 1.5 f ( ) : Applied to 7mmL products D45 P 1.5 2.0 f d 0.45 0.45 6.3 8 10 2.5 3.5 5.0 0.5 (0.45) 0.6 0.6 (mm) • Please refer to page 21 about the end seal configulation. Please refer to page 21, 22, 23 about the formed or taped product spec. Please refer to page 3 for the minimum order quantity. Dimension table in next page. CAT.8100V ALUMINUM ELECTROLYTIC CAPACITORS HC series Standard ratings V (Code) 6.3 (0J) Case size φD × L (mm) (mArms) 20˚C / 100kHz 105˚C / 100kHz 10 (1A) Rated ripple Case size φD × L (mm) (mArms) 20˚C / 100kHz 105˚C / 100kHz 16 (1C) Rated ripple Case size φD × L (mm) (mArms) 20˚C / 100kHz 105˚C / 100kHz Item Cap.(µF) Code Impedance (Ω ) MAX. Impedance (Ω ) MAX. Impedance (Ω ) MAX. Rated ripple 22 33 47 100 220 330 470 1000 220 330 470 101 221 331 471 102 4×7 5×7 6.3 × 7 6.3 × 11 8 × 11.5 8 × 11.5 10 × 16 0.48 0.26 0.15 0.077 0.043 0.043 0.024 230 350 480 640 910 910 1650 4×7 5×7 5×7 6.3 × 7 8 × 11.5 8 × 11.5 10 × 12.5 0.49 0.26 0.26 0.15 0.044 0.043 0.030 230 350 350 480 910 910 1230 5×7 5×7 6.3 × 7 6.3 × 11 8 × 11.5 10 × 12.5 10 × 16 0.26 0.26 0.15 0.078 0.044 0.030 0.025 350 350 480 640 910 1230 1650 V (Code) 25 (1E) Case size φD × L (mm) (mArms) 20˚C / 100kHz 105˚C / 100kHz 35 (1V) Rated ripple Case size φD × L (mm) (mArms) 20˚C / 100kHz 105˚C / 100kHz Item Cap. (µF) Code Impedance (Ω ) MAX. Impedance (Ω ) MAX. Rated ripple 4.7 10 22 33 47 100 220 330 4R7 100 220 330 470 101 221 331 4×7 5×7 6.3 × 7 6.3 × 7 6.3 × 11 10 × 12.5 10 × 16 0.52 0.27 0.16 0.15 0.078 0.031 0.026 230 350 480 480 640 1230 1650 4×7 5×7 6.3 × 7 6.3 × 7 6.3 × 11 8 × 11.5 10 × 16 0.64 0.33 0.17 0.16 0.089 0.048 0.026 230 350 480 480 640 910 1650 Frequency coefficient of rated ripple current Cap. (µF) Frequency 120Hz 0.40 0.47 0.55 1kHz 0.68 0.75 0.85 10kHz 0.90 0.95 0.98 100kHz 1.00 1.00 1.00 4.7 ~ 33 47 ~ 330 470 ~ 1000 CAT.8100V