ULH2D150MNL1GS

ALUMINUM  ELECTROLYTIC  CAPACITORS ULH Chip Type, High Voltage. High Reliability. Chip type, High voltage and High Reliability. Load life of 4000 hours at +125°C. Applicable to automatic mounting machine using carrier tape. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. Please contact us for details. ULH ULT Long Life Specifications Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current Performance Characteristics –40 to +125°C 160 to 450V 2.2 to 27µF ± 20% at 120Hz, 20°C After 1 minute's application of rated voltage at 20°C, leakage current is not more than 0.04CV+100 (µA). Measurement frequency : 120Hz at 20°C Tangent of loss angle (tan δ) Rated voltage (V) tan δ (max.) 160 0.20 200 0.20 250 0.25 400 0.25 450 0.30 Measurement frequency : 120Hz Stability at Low Temperature Rated voltage (V) Impedance ratio Z(–40°C) / Z(+20°C) ZT / Z20 (max.) 160 200 250 400 450 6 6 10 10 15 The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 4000 hours at 125°C. Endurance Shelf Life Resistance to soldering heat Marking Type numbering system (Example : 400V 5.6µF) （φ8, φ10） Positive C±0.2 0.3max. Series Capacitance L ±1.0 4 5 6 7 8 9 10 11 12 13 14 Capacitance tolerance (±20%) Rated capacitance (5.6µF) H Negative Rated voltage (400V) Series name (mm) A B C E L H 3 Configuration Pressure relief vent 8 × 10 10 × 10 2.9 3.2 10.3 8.3 10.3 8.3 3.1 4.5 10 10 0.8 to 1.1 0.8 to 1.1 2 Taping code A±0.2 E A±0.2 B±0.2 φD±0.5 A2 5.6 2G LH Lot No. 1 U L H 2 G 5 R 6 MN L 1 GS 0.5max. Plastic platform Voltage(2G : 400V) φD × L Within ±30% of the initial capacitance value 300% or less than the intial specified value Less than or equal to the initial specified value After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, Within ±10% of the initial capacitance value Capacitance change which is maintained at 250°C and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they Less than or equal to the initial specified value tan δ shall meet the characteristic requirements listed at right Less than or equal to the initial specified value Leakage current when they are removed from the plate. Black print on the case top. ※ I : Leakage Current (μA), C : Rated Capacitance (μF), V : Rated Voltage (V) Chip Type Trade mark Capacitance change tan δ Leakage current Type 10 × 13.5 3.2 10.3 10.3 4.5 13.5 0.8 to 1.1 Voltage V Code 160 200 250 400 450 2C 2D 2E 2G 2W Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Dimension table in next page. CAT.8100L ALUMINUM  ELECTROLYTIC  CAPACITORS ULH ■ Dimensions Rated Voltage （V） （code） 160 （2C） 200 （2D） Leakage Current （µA） at 20℃ after 1 minute Rated Ripple （mArms） （125℃/120Hz） Part Number 0.20 176.8 45 ULH2C120MNL1GS 10× 10 0.20 215.2 60 ULH2C180MNL1GS 10× 13.5 0.20 272.8 65 ULH2C270MNL1GS 10 8× 10 0.20 180 45 ULH2D100MNL1GS 15 10× 10 0.20 220 60 ULH2D150MNL1GS 22 10× 13.5 0.20 276 65 ULH2D220MNL1GS Rated Capacitance （µF） Case Size φD×L（mm） tan δ 12 8× 10 18 27 7.5 250 （2E） 400 （2G） 450 （2W） （ ） 8× 10 0.25 175 30 ULH2E7R5MNL1GS 12 10× 10 0.25 220 45 ULH2E120MNL1GS 15 10×13.5 0.25 250 50 ULH2E150MNL1GS 3.3 8×10 0.25 152.8 30 ULH2G3R3MNL1GS 5.6 10× 10 0.25 189.6 45 ULH2G5R6MNL1GS 7.5 10× 13.5 0.25 220 50 ULH2G7R5MNL1GS 2.2 8× 10 0.30 139.6 20 ULH2W2R2MNL1GS 3.9 10× 10 0.30 170.2 35 ULH2W3R9MNL1GS 5.6 10× 13.5 0.30 200.8 40 ULH2W5R6MNL1GS For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. CAT.8100L